Hi, my TytN begin to show me "no GSM", i upgrade to WM6, but the process stop in 12% and error 262 appears. i tried to fix with this method:
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems#problem5
everything is ok, but when i use the Simulock, the utility go until the final part and says me that cant communicate with the device and the indicator bar remains in 0%
any suggestion
Related
I'm following Mr Vanx's guide for upgrading my Jasjam from WM5 to WM6, but am having trouble with flashing the new bootloader onto the device. It's a second-hand telstra imate. I just bought it off ebay a couple of weeks ago and need to upgrade it to get it to read sdhc memory cards. I can't get it to connect to optus' (my mobile contract provider) mobile internet either, which I did via GPRS on my old phone. I'm hoping by upgrading the OS I can remove all of Telstra's code so It's not trying to connect to telstra's 3g network when I start the web browser.
When I get to the last step of the Hard-SPL installation, where the "updater will flash the new SPL and then restart your device (this will take generally less than a minute)" , the phone restarts almost immediately after clicking yes when prompted on the phone. The screen quickly goes to the bootloader screen, which says
"herm 100
IPL-SSPL by Des
Herm 100
SPL-1.09.ds"
The PC says that it can't connect to the phone and I should check the cable, which is still connected
The phone stays on the bootloader screen until I hit the soft reset, and WM5 boots like normal.
Has anyone else had this happen?
Yup,
Same problem over here. I had the problem before. But i fixed it! The only question is how did i do that? short term memory.
I'm trying to solve the problem. If its solved i will let you know.
Till then hang on
I've been trying again today. Still getting the same result, though I figured out if I just leave it when it gets to the bootloader screen, the pc I'm installing from eventually comes up with Error 260.
I'm thinking now that the XP firewall may be the issue, but I'm having trouble disabling it because it's managed by "group policies" (it's a work computer). I'm going to try either finding out which port to unblock, or starting the pc in safe mode so I can disable the firewall altogether.
I fixed the problem with the following softwaretool Hypercore. Just intergrate the Hard spl from olipro. After this the error dissapears.
Hello, gents.
Trying to upgrade SPL with v7 on a friends 8525 but getting timeout or connection dropped. When attempting to install, it's get's as far as rebooting the device after accepting "yes". It then attempts the SPL install and eventually error 260 shows on the workstation screen with the raibow screen left on the device.
Read somewhere that .NET 2.0 would correct this but I already have it installed.
Error 260 on "Official" WM6 ROM
ehartley said:
It then attempts the...install and eventually error 260 shows on the workstation screen with the raibow screen left on the device.
Click to expand...
Click to collapse
I am having the same error message crop up when I try to install the latest ROM from HTC.
I am on Vista (but that really doesn't matter because A: I followed mrvanx's instructions to add the proper driver and B: I get the same crap from my roomate's XP machine).
When I run the ROM, it checks the PC, and then I get to the wizard. I check that I know this will erase my device, and then I check that I have done all of the things I need to do (activesync, etc.)
I acknowledge that I want to upgrade, and that I am going from my old ROM to the latest ROM, and click next...
At which time my phone screen goes dark and drops my connection via sync and the update bar stays at 0%. 30 seconds later I have a message come up that says Erro [260]: Connection, and some piss poor advice from HTC that says restart and reconnect everything and try again...
My Phone(Herm100 AT&T 8525) is running:
HardSPL 2.10 (v.7)
ROM Version 2.15.502.3
Radio 1.40.30.00
Protocol 32.73.7020.16H
HAAAAALLLLLLPPPPPPPPPP!!!!!!
Hi guys,
I've got a T-Mobile MDA Vario 2 (Hermes).
i used the "HTC Hermes SIM & CID Unlocker *New* version v3a" tool so i could then load any ROM i want. I followed the instructions perfectly and then ran the unlocker, and that went fine too, however, when i'm trying to change to a particular ROM version, it gives me a "error 101 : Connection Error" after it tries to check the status of the device......it gets to the tricolour bootloader screen absolutely fine and the screen shows the following -
HERM300
IPL - 1.01
HERM300
SPL-1.40Olipro
It sits saying 'Checking the information onyour device..........please wait' for around 2 minutes, then kicks back and gives me the "Error 101 : Connection Error".
I have tried the search function, but there's not a lot i can find on the problem.
Can anyone help?
Thanks
Mark
That drove me crazy too until I finally found a post on another board explaining what to do.
If you notice when the updater is running, your activesync program will exit. Immediatelly restart activesync when you see it exit. It will not reconnect to your device, in fact it will show not connected but that is ok. The ruu is only using the activesync program, not to actual connection to communicate with your device.
I actually created an easily accessible activesync icon on the desktop of my PC so I can restart it quickly. Watch it closely, I have had the activesync program exit up to two times before I ever get the installation underway.
I guess this is normal, based on what I have read elsewhere.
Hope this helps. Let me know if you are successful with this method.
I'm currently trying to update my HERM100 (HTC 8525) and every time I run the update utility it stalls 11% for a number of minutes and then returns ERROR [262]: Update Error. I'm currently running SPL-2.10 as a bootloader. Any idea what might be causing this?
You have with Radio part of the device. Do you have GSM?
I think I might not, I don't get a no GSM error but when windows boots I don't have any phone functionality at all
failing at 11% is because you have a corrupted radio. try flashing a radio only rom
I have the Touch Pro for Sprint, bought it today.
I have followed every How-To I can find, and I think I'm doing something wrong.
In windows XP, phone connected to USB, ActiveSync connected. I run the Raphael CDMA Hard SPL and... nothing happens. It just times out.
If I try Mighty Rom's CDMA installer for Touch Pro, It gets tot he security screen, and then the percentage screen, but stays at 0 and eventually times out with "Connection Error".
I have no idea what I'm doing wrong.
Any suggestions?
Edit: It's the 262 Error