Hye
After use HardSPl
I try to flash my Diamond Pro
and I have Eoor 244 : Invalid Device ID
and the flash stop
So what is the problem
thanks
lilive10 said:
Error 244 : Invalid Device ID
Click to expand...
Click to collapse
u wont get that error is hardSPL is installed properly. check ur spl by putting ur device in bootloader mode. if ur hardspl is correctly installed, continue to flash rom using raphael ruuwrapper by cmonex.
thanks
but how i go in bootloader mode and then see if hardspl is well install?
Next time pls read the thread thoroughly especially when u r upgrading ur device. u can get more info from where u get the correct HardSPL for raphael.
Just an advise from friend to a friend. U can go to the main thread to get more info. For entering bootloader, just press voldown + reset hole when device is on.
Hi
I use the correct hardspl for raphael
when I go in boot mode, I see 1.90 Olinex I think is it the good one
But nothing change
Sorry, but what can I do now?
Thanks
Related
please anyone in here help me for my x01ht
1. i flash with HER_DopodAsia_AUS_1[1].30.707.4_1.20.31.10_WWE_Ship.exe
2. when it flash until 14% , it stop
3. i plug out cable and restart phone , now phone only can go into bootloader mode
4. in bootloader mode , it show
HERM IPL-1.01
HERM SPL-1.06
5. now i flash whatever file into this phone , it will show invalid vender id
6. please teach me how to do now all master
thanks !
file i try to flash
-RUU_X01HT_1.33.761.4_1.14.00.10.exe
-RUU_Hermes_DopodAsia_AUS_1.30.707.8_1.27.30.10_WWE_SHIP.exe
-HER_DopodAsia_1237074_1060010_WWE_SHIP.exe
all not work , will show invalid vender id
check the two stickies in this forum - bricked device and free unlocker. If you can run the unlocker, it will SuperCID your phone, if you can get that far.
If not, check out the bricked device thread - lot's going on in there.
Also, have you tried putting the ROM back on that was there to start with? Inalid Vendor ID is a failed check by the phone to match Phone CID with ROM CID. If you didn't fry it out, then you whould be able to put the OLD ROM back on. If so, you have a little more work ahead of you.
no unlocker not work for me , please teach me step by step what should i do ... thanks for your help
hanyean1 said:
no unlocker not work for me , please teach me step by step what should i do ... thanks for your help
Click to expand...
Click to collapse
Shamelessly stolen from one of pof's recent posts but still applicable...
10 READ(wiki)
20 READ(Hermes->forums->stickies)
30 READ(Hermes->forums)
40 IF (Questions?) GOTO 10
50 FLASH(Hermes)
LOL
Closing this thread as he already posted here:
http://forum.xda-developers.com/showthread.php?t=286755
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
cowballz69 said:
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
Click to expand...
Click to collapse
Have you took the sim card and memory card out?????
Jay
yes they are both out when tryign to flash, been over a week with out a working athena
cowballz69 said:
yes they are both out when tryign to flash, been over a week with out a working athena
Click to expand...
Click to collapse
try flashing your original ROM which should be found in the wiki section.
ignore what I said below and report back if you were able to load your original ROM
***Ignore this read above**Once your phone is working , do the athena wrapper which should load SPL 1.2
Also read this
http://forum.xda-developers.com/showthread.php?t=429013
yes I tryed to flash the original rom (its a wm5 i beleive to), still gets error after 1%,, downloaded both on the wiki and the ftp site, =\ been over a week so far no clues on why i cant flash, i even tryed to change the mac address using mtty, but instead of going into level = 0 , i get level = FF witch means the phone is locked out from flashing anything threw mtty,
thank u guys so much for responding on my issue
I also tryed doing the unlocker and its a no go
If the error when it stops at 1% is "invalid model id" the solution is here http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
cowballz69 said:
yes I tryed to flash the original rom (its a wm5 i beleive to), still gets error after 1%,, downloaded both on the wiki and the ftp site, =\ been over a week so far no clues on why i cant flash, i even tryed to change the mac address using mtty, but instead of going into level = 0 , i get level = FF witch means the phone is locked out from flashing anything threw mtty,
thank u guys so much for responding on my issue
I also tryed doing the unlocker and its a no go
Click to expand...
Click to collapse
I think this means your phone is not unlocked
with respect to sergiopi , you cant do the mtty script.
I would suggest you msg cmonex or try to talk to her on IRC on the
dxa-devs channel
addendum
seeing that you have nothing to lose, why dont you try flashing the original rom from the sd card using the method in the wiki
cowballz69 said:
anyone know what rom is compatible with athe100 SPL 1.10 ?
i know theirs lots of 1.2 and 3.5 spl roms, i tryed to flash a 3.5spl on my phone and now only way i can turn on the phone is in bootloader, i try to flash the phone but it always gets stuck at 1%, can anyone assist me?
Click to expand...
Click to collapse
I have the same problem.
what I do...
I have ameo t-mobile...windows mobile 5.0
run AthenaUnlocker
Step 1 make all finish noc problem
Step 2 hung up on 60 %
bootloader no problem....but can´t flash original flash always stuck at 1% and reboot...
flashing the original rom from the sd card using the method in the wiki ...
make it, but no do...on screen see
cheking...
loading....
than come on screen
0002802
ching...
loading...
not allowed
sergiopi said:
If the error when it stops at 1% is "invalid model id" the solution is here http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
Click to expand...
Click to collapse
My error when it stops at 1% is "invalid vender id"
my image version is demaged
Re: Ameo from t-Mobile german - repair
________________________________________
hi
what is your CID? use mtty command "info 2" to find out.
for example, if it is TMOB_007, you have to find a shipped athena rom with that CID.
if you cannot find a matching rom, let me know, i can still help,
cmonex
HTCS Þ?ÒtHTCE
please need halp
thx
felix999
read this post http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
lakeman said:
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
Click to expand...
Click to collapse
in mtty this can read:
when type task 32
become LEVEL: FF
when type info 2:
HTCS Þ?ÒtHTCE
my CID is 1.1
on bootscreen can see this:
ATHE100
IPL-v1.00
ATHE100
SPL-v1.10.RP00
what I do before...
Ameo WM 5.0 >>>>my mistake not update to WM6.0
run AthenaUnlocker
STEP1>>>OK
STEP2>>>by 60 % hang and stopped....
and now have the big problems.....Image ROM of t-Mobile 5.0 german demaged
can´t flash any rom´s
thx for hel or I want to pay bucks for service, when ma ameo live again...
felix999
lakeman said:
read this post which tells you how to run mtty
follow the instructions to start mtty then press enter to get the cmd prompt
then type info 2 to get your CID
depending on this you will be able to flash the apprpriate ROM
Click to expand...
Click to collapse
this is my CID
Cmd>info 2
info 2
Wait interpreter timeout
HTCS Þ?ÒtHTCE
????????
don´t know
felix999
Athena mobile 6 > SPL 1.10
become today a answer from crazy cat, that olipro say must take an rom in athena forum....
I flaswh with so many roms...anytime same error: error 294 - invalid vendor ID.....
My SPL 1.10 >>> can´t find a rom with SPL 1.10
what rom can repair my demaged ameo?????
thx for help
felix999
problem solved with ONLINEHELP from>>>>>cmonex>>>><<:::::>><<:::E:::>><<:::R:::>><<:::F:::>><<:::E:::>><<:::C:::>><<:::T:::>>
thx
felix999
lakeman said:
try flashing your original ROM which should be found in the wiki section.
Click to expand...
Click to collapse
Is this how you solved your problem?
I upgrade my rom and now he stucks on de first screen when windows mobile show i do everything i can and i don no what do more
The multi port program give-me this error
Cmd>ls boo.bin
clean up the image temp buffer at 0x8C100000 Length 0x03A00000
BOOTLOAD_PAGE_TABLE_BASE_C_VIRTUAL= 0x8C080000
Clear image temp buffer done .
MTTYDownloadImage
Not allow operation!
Error : DownloadImage return error (code = 0xFFFFFFFF)
Is everything i can do to my gene come back to life???????
Please Help me
Do you already do a SPL unlock?
If yes, just flash with another ROM.
Go to bootloader by press and hold camera then reset, release reset but still hold camera untill tri color appear, connect usb cable to pc then flash again with another ROM.
How thing i have all ready done that?but show-me how i do to see if i done well
When im restarting the pda the information tha show is
onbl 1.07.0000
spl 1.07.0000
gsm 02.71.90
os 1.17.0.0
After that screen goes to windows mobile screen and stuck
But is i do the combinations of the power button and camera i go to the 3 colors screen but when i do a update the program go to 2 % and reset
Please help-me
I think i all ready done that. But show-me how i do?
When i start the pda when arrive to the screen with the windows mobile picture stuck in there.
The information that i have in the begining is
onbl 1.07.0000
spl 1.07.0000
gsm 02.71.90
os 1.17.0.0
When i startup the device i can go to the 3 colors screen but when i tried to
upgrade the rom t when arrive at 2 % the device reset and give-me a error
i don now what i do more please help-me
@tonysucre do HSPL
hi
as per the nos u have posted u have not done HSPL
ur spl should end with .olip or .oref at the end instead of .0000
go to the tut given by Krazy and read many times use the tools and do the needful given in the same section viabhav has also given a tool
chek on both good luck
tonysucre said:
I think i all ready done that. But show-me how i do?
When i start the pda when arrive to the screen with the windows mobile picture stuck in there.
The information that i have in the begining is
onbl 1.07.0000
spl 1.07.0000
gsm 02.71.90
os 1.17.0.0
When i startup the device i can go to the 3 colors screen but when i tried to
upgrade the rom t when arrive at 2 % the device reset and give-me a error
i don now what i do more please help-me
Click to expand...
Click to collapse
haree said:
hi
as per the nos u have posted u have not done HSPL
ur spl should end with .olip or .oref at the end instead of .0000
go to the tut given by Krazy and read many times use the tools and do the needful given in the same section viabhav has also given a tool
chek on both good luck
Click to expand...
Click to collapse
Can you give-me the link of the tutorial?
Tks
@haree
buddy you are wasting your time .
There is a thread named upgrading ... by krazy as well as a thread by vaibhav named automatic SPL Updater. Just search a bit, son.
or may be you can take the cell to haree who will patch it for you
I Have already tried that but the thing but i cant put thing in the memory phone only in the sd card
Help please
after upgrade to 6.5 screen showing windows mobile 6.5 onyl
I used SumitsProUsersROM_WM6.5_build21815_OldGene_Fixed to upgrade its struck at windows mobile 6.5 screen only nothing happening.
not able to flash again. Aslo want to note that while I was ugrading it shows me something like "sudden loss of power"
Pls help my phone is not working now.
thaks
recharge the battery for mare than 1 hour and try again
After 6 hours of trying to change spl to flash the rom i haven´t manage to do anything more ist´s exactaly the same that i have all ready i have download a lot´s o rom´s and nothing i have tried the to do updating the spl by the sd card and nothing happen because i can´t put anything in the memory of the phone i only can put thing in the card from my computers card reader to trying to change the spl to 1.10-Olipro to flash the rom but i can´t
I don´t no what i have do more?
please anyone with the same problem can help-me
Tks
what error are u getting while upgrading?
vaibhav_batra_the_techguy said:
what error are u getting while upgrading?
Click to expand...
Click to collapse
error 270
is the same that a told is star to upgrading and in the 2 % the phone restarts and give-me that error i thing is because spl is 1.7.0000 or not?
I just see i hav cid lock and and dont now i unlock ?any help
@tonysucre
see
below link as i had told u before u have not done HSPL
u go to the below links and save them on ur comp and Read no one is going to hand hold u and u dont need it with such nice tutes given pls not im a guy with Zero tech skills and i did it so u can as my boss would say its not rocket science
& i dont have any gene tools with me as i have upgraded to another phone (see my sign)
good luck
http://forum.xda-developers.com/showthread.php?t=513329
http://forum.xda-developers.com/showthread.php?t=472169
tonysucre said:
Help please
Click to expand...
Click to collapse
i flashed my new gene
now i am at the tri colour screen
its showing ONBL 1.17.0000
SPL 1.10.Olip
when i give a click on Rom update Utility
its giving me ERROR [300] : INVALID UPDATE TOOL
please help me wat to do
its almost been a month, that my phone is not working
Follow krazy's thread, starting with the gene unbricker step.
you have only done 50% hspl, if you are sure your Gene is New
u can also use @fusioncoast
hi
just a suggestion Viabhav has provided a tool to chek if ur phone is old or new use it and he has also provided the HSPL tool also try it it will tell u wether ur phone is new or old
goodluck
fusioncoast said:
i flashed my new gene
now i am at the tri colour screen
its showing ONBL 1.17.0000
SPL 1.10.Olip
when i give a click on Rom update Utility
its giving me ERROR [300] : INVALID UPDATE TOOL
please help me wat to do
its almost been a month, that my phone is not working
Click to expand...
Click to collapse
now the phone does not reboot after updating Rom
i was successfull in updating the ROm, but after clicking finish....the phone should retart
but it does not restart
tried manual restarting.....
tried hard reset
nothing works
my phone is not booting up after updating the ROM
try this @fusioncoast
hi
try this
1.off the phone & take the battery out
2. press the power button on the phone for a few secs after removing battery
3.put battery back in the phone
4. press& hold camera button & then power button this will give u tricolor
use USB and Flash a new ROM
if ur sure ur SPL is .olip then Flash with old gene ROM or look in this same site besfen has also provided the orginal wm6 ROM u can also try the same
good luck
fusioncoast said:
i was successfull in updating the ROm, but after clicking finish....the phone should retart
but it does not restart
tried manual restarting.....
tried hard reset
nothing works
my phone is not booting up after updating the ROM
Click to expand...
Click to collapse
When I attach my niki in bootloader mode with my pc and the i try to do hardspl there comes white screen showing a bar 0% but it did not go ahead like other htc it stays on and after some time there come an error 262 saying this
the rom update utility has encountered a communication error during the update process........etc
i also acted step b step on the guidence of this program but in vain so plez help me how can i hard spl my niki to upgrade new rom ......plzzzzzzzzz
Nofear99 said:
When I attach my niki in bootloader mode with my pc and the i try to do hardspl there comes white screen showing a bar 0% but it did not go ahead like other htc it stays on and after some time there come an error 262 saying this
the rom update utility has encountered a communication error during the update process........etc
i also acted step b step on the guidence of this program but in vain so plez help me how can i hard spl my niki to upgrade new rom ......plzzzzzzzzz
Click to expand...
Click to collapse
if u have already spl 1.5 on ur device then,after runing hard spl 1.22,the moment u c the tri colour on ur device,take the data cable off from pc.when u c 'serial' on ur device,insert the cable again.the process will be complete.
regards
thanks to answer but same problem...
deepankerjha said:
if u have already spl 1.5 on ur device then,after runing hard spl 1.22,the moment u c the tri colour on ur device,take the data cable off from pc.when u c 'serial' on ur device,insert the cable again.the process will be complete.
regards
Click to expand...
Click to collapse
i can see on boot loader mode my spl is 1.16.0000
niki200 cpld-4
plzz tell me another solution
i will be thankful to u
Nofear99 said:
i can see on boot loader mode my spl is 1.16.0000
niki200 cpld-4
plzz tell me another solution
i will be thankful to u
Click to expand...
Click to collapse
is ur device sim unlocked?moreover i think u have already hard spl installed on ur device pal.