Related
I have been reading through thr forums for a resolution to TT5 freezing on the XDAIIi, so far I have downloaded the update from o2.co.uk and the TOM TOM 5 update but to no avail, I found out from another forum that if you put the phone into flight mode it stops it freezing and guess what it did!!!
So a different radio version is needed any ideas? Where can I get a Radio Version that works with TT5 as I use traffic and need a signal for GPRS.
HELP!!!!
ftp://ftp.xda-developers.com/O2 Alpine Roms/
Try this link, I installed it to my Xda 2i and have not had any problems with it at all
ftp://ftp.xda-developers.com/
Go to the o2 alpine roms folder (top right hand corner of page)
download the rar file there. Good Luck
Hummm
This did not work TOMTOM still froze I have got hold of radio version 1.20.00 (beta test from O2) awaiting to see if work will post response
Hey frog can you post that beta radio 1.20
Can anyone share their experience upgrading their Bell HTC6800 ROM (including radio, unlocking SPL, and upgrading PRL) with DCD 3.0.1? I have never done it before but curious to hear if anyone has had success or failure.
I noticed that DCD released a Bell ROM in his 2.3.2 kitchen but not in his 3.0.0 kitchen. Does anyone know how to port the correct Bell settings into the 3.0.0 release?
My main reason for upgrading is of course better performance but more importantly I am curious about aGPS and how I can use it instead of my Bluetooth GPS receiver. If anyone can share that would be much appreciated.
http://rapidshare.com/files/99219142/DCD_3.0.1_Bell.exe
Check the last page of this thread
http://forum.xda-developers.com/showthread.php?t=363693
Thanks origins81. I noticed now that DCD added the Bell ROM to his 3.0.1. So can you share you experience with this ROM upgrade? Did you have any problems (I assume you've done this before)? Can you share your experience if you are a Bell HTC 6800 user?
1. If you have not already done so, run the 2.40-olipro unlocker. Your device will again be left in tri-color screen.
2. Flash the official sprint 3.35 update.
3. When the device boots for the first time, do not pass screen calibration. Flash a 3.x.x ROM. (that being the custom rom of your choice)
Think I only used the official Bell rom for about a day before i got sick and tired of it and flashed to one of DCD's clean roms, never looked back since then...
As much as I hate Bell, I purchased this phone, had it for about 7 months and got into flashing roms, well, this newest ROM from DCD was the trickiest. First I tried using the Kitchen (disaster), I finally got it to work, installed it, and I kinda forgot to read the instructions, you have to be SURE to install the Olipro 2.40 first, and flash to the new radio, or it will do one of two things. 1st it will either continuously restart or 2nd thing is it will get stuck on the infamous red, blue, and green screen. However if you do get stuck on this, you can flash the rom again, then install the newest radio and it *should work.
But after all that pain and misery, I got a little better signal (I'm not too sure if this is caused by the new rom or not), the GPS works great as always, and seeing as Bell charges 2 arms and your first child for data, I haven't tried the speeds for Rev. A.
P.S- If you ever need help with your Bell 6800, just ask, I've been troubleshooting the same phone for a couple months, and I know how to use a kitchen, just a PM away.
Thanks guys. You have instilled more confidence in me now. I am just going to make sure I have the original stock ROM from ustar as well as the Titan re-locker just in case (I want a backout plan). I will wait a little longer until everyone irons out the kinks of this new 3.35 radio and I will give the latest DCD ROM a try. Thanks again!
I've used the SPRINT update and it works fine. I've added the quick GPS program that comes with the DCD version and I am going to change the startup logos from Sprint to Bell...(As soon as I figure out how). I didn't need to reprogram anything!!
I just got my phone today, gonna give this a shot...
oh man... i ran the olipro 2.4 file and it took me to the tri color mode and then tried to flash it with the latest sprint update. it went up to 4-5% and then it showed an error of Update Utility. i tried to go bak to the Bell update and it did the samething but this time after 1%. can someone please help me out here? I'm with bell.
ok now i'm stuck at the bell screen and at the bottom it says "No Radio" cuz i tried flashing the dcd file.
Well, to begin with, here are the steps I took to accomplish what I have.
1. Flash Olipro 2.40
2. Flash Radio to 3.35 (For the newest version of DCD's rom)
3. Flash the ROM to DCD's rom.
Now, the first time I did this, I got stuck at the tri-color screen, such a pain. I then tried flashing the rom again, and it rebooted continuously and I had no idea why. This was because I didn't flash to the newest radio. So I did that, and it worked, so try those steps, and good luck.
On problem that I did notice is that my phone always has the roaming triangle on?? Hopefully it's not costing me roaming charges... I was going to try and use the DCD 3.0.1 rom but don't want to chance it. I'm going to try playing with it some more an see what happens.
I'm running DCD 3.0.1 on my Bell 6800 and it's working great so far (day 2)
Follow Origins81's install points above, and remain calm if it takes a try or two to get past the 2.40-olipro unlocker 3-color screen step.
I'm having some issues ActiveSync'ing to both work and home PCs, but I don't think it's related to this ROM.
GPS works great with Google Maps
The alarm clock bug is fixed (e.g. not working when plugged in)
Got it working and everyhthing is great except is doesnt play video in the media player...Working on it.
Well for some reason I can't seem to activate my phone. I hit Talk then I enter ##911224#. It tries to connect for 15 secs then hangs up.
I _thought_ I did everything properly.
1) Ran Olipro2.40 (actually it was the unlock from http://www.phonenews.com/how-to-add-gps-to-htc-mogul-xv6800-p4000-titan-2663/) it looks like it's got Olipro2.40 in it.
2) ran official upgrade from sprint (RUU_TITAN_SPRINT_WWE_3.35.651.2_RS_TITAN_3.35.04_4350H_SPCS_AM_Ship.exe)
3) Extracted DCD_3.0.1_Bell.exe and ran the RUU.
hope I didn't perma-brick it.
M
Ok fixed it. Browsed around the and found out in a Howard forum that you have to type ##111111# (doh!) before. Ok my heart can start beating again! Posted for posterity. The code that I used must have been for a different area. This phone is from the GTA.
can you give me a link to those howard forum posts because i ran into a problem ... after a last flash my phone works but its not activated... I tryied ##111111# but i get a code check error... ##911224# doesnt do anything... ##778# works but 000000 code doesnt so i cant get in... HELP
Roaming After Update
After suffering with the pesky Bluetooth issues with my HTC, I thought I'd do some searching on the Internet to see if others had the same issues. Lo and behold, it looks like a real bug with the HTC. After reading some forums, it looked like the latest Sprint release would cure the problem. I downloaded an unlock program ("Hard-SPL-MFG") and the Spring update (RUU_TITAN_SPRINT_WWE_3.35.651.2_RS_TITAN_3.35.04_4350H_SPCS_AM_Ship)
and proceeded to update my HTC.
After a few unsuccessful attempts (stuck at the three color bars a couple of times, restarting a few times on it's own) I managed to get the unlock code and Sprint update installed.
The problem I have now is that it appears that I am now roaming even though I'm in my calling area (I'm with Bell Canada)!
Help! What should I do??
Check the bottom link out, had similar issues when I first flashed. If you have any further questions let me know
http://forum.xda-developers.com/showthread.php?t=363693&highlight=FOR+BELL
i follow the step, but when the phone restart, i stuck a the bell screen...
i'm unable to connect with the usb.
Can you able to help me ? to complete the installation or trying to go back OEM
- i do the first step; see the red, green, blue screen (http://forum.ppcgeeks.com/showthread.php?t=9093)
- flash the rom
- now stuck......
thx for your precious help
TwistedWaffle said:
As much as I hate Bell, I purchased this phone, had it for about 7 months and got into flashing roms, well, this newest ROM from DCD was the trickiest. First I tried using the Kitchen (disaster), I finally got it to work, installed it, and I kinda forgot to read the instructions, you have to be SURE to install the Olipro 2.40 first, and flash to the new radio, or it will do one of two things. 1st it will either continuously restart or 2nd thing is it will get stuck on the infamous red, blue, and green screen. However if you do get stuck on this, you can flash the rom again, then install the newest radio and it *should work.
But after all that pain and misery, I got a little better signal (I'm not too sure if this is caused by the new rom or not), the GPS works great as always, and seeing as Bell charges 2 arms and your first child for data, I haven't tried the speeds for Rev. A.
P.S- If you ever need help with your Bell 6800, just ask, I've been troubleshooting the same phone for a couple months, and I know how to use a kitchen, just a PM away.
Click to expand...
Click to collapse
Hi TwistedWaffle, Are you from the montreal region? I am looking for somebody who would do this stuff for me... Can you help?
is there a tutorial to get the GPS functioning on the titan? I have flashed the bootloader and radio and rom with the dcd kitchen. It finds the gps but it wont get signal from anything. Trying to get trackme to function. Ideas?
Try here:
http://forum.xda-developers.com/showthread.php?t=363431
i have tried that already. When I try use gps view and tell it to open gps or scan for the gps it locks up. Ideas?
Well I upgraded to DCD 3.2.4 and 3.42.50 radio rom. For some reason now I cannot get a connection through WiFi , it gives me errors such as: Cannot obtain a server assigned IP address. Try again later or enter and ip address in network settings. It also says it cannot connect to the network at times.
I am on the Verizon Wireless network. Thank you in advance for your help.
Anyone???????
Did you install the customization?
do you have wifi router install
If you have WiFiRouter installed, wireless will not work until u remove it from the list.
ill find the cab you need to fix it the wifi router changes reg files and theres a cab around here that fixes it
I installed WMWifiRouter im not able to remove it from my programs list no matter how I try. That shouldn't be the problem either way because it did this before I even installed the software.
if you dont have access to your router you have to wait until your connection/ip clears out.
if you do have access clear out your ip from router setup and reconnect
Here is the fix i found the cab.
Installed CAB still same problem: Cannot connect to the network. Check your network and service provider settings and try again. Also cannot obtain a server assigned ip address. Try again later or enter an ip address in network settings.
Anyone can help?
I really need my WiFi to work .... if it costs to fix this problem I will.
Did you install the carrier cab?
I have had the same problem since upgrading to 3.3.4 from 3.2.6. I ran the carrier customization and everything else works just fine. I have DCD's version of the 3.42.50 radio. The wifi switch is on and if you hit wifi in comm manager the icon blink on and then off in about 1 second. I don't have wifi-router installed. I'm kind of lost at the moment, but haven't had a chance to downgrade to 3.2.6 to see if it works again to rule out the wifi radio being dead.
Same Problem
I am in Canada and have the Mogul (Telus P4000) with DCD 3.2.5 Radio 3.42.50 and the WIFI is NOT working and I have NEVER installed WiFiRouter.
Is it a radio version problem?
Any help would be appreciated
same problem here, I updated the ppc6800 to the last rom from sprint 3.35 with dcd 3.01 from bell and still same thing the wifi is not working.
is it one hardware problem or can I fix with with a cab file ?
DCD 3.0.1 is so old. Use 3.3.4 or 3.2.6 instead and do a reflash to fix the problem.
drewcam888 said:
DCD 3.0.1 is so old. Use 3.3.4 or 3.2.6 instead and do a reflash to fix the problem.
Click to expand...
Click to collapse
I need one for bell, do you have a link ?
http://dcd1182.n715dp.com/
I have downloaded dcd Bell Carrier 20081031.cab
what version is it ? and how do I apply it to the phone ?
thank you
I am trying to unlock my gps and have found lots of nice builds but i am confused as to which provider rom i should use. dcd's build looks the best to me. from what i have read about what i want to accomplish.
here is my data
software 2.17.557.0
firmware 1.61.00
hardware verson 0003
activation date mar 31 2008
device info.
rom version 2.17.557.0
rom date 11/20/07
radio version 1.64.00
i can read and i am not affraid to get my hands dirty but i didn't know which rock to start looking under.
thanks
nick
xbeergogglesx said:
I am trying to unlock my gps and have found lots of nice builds but i am confused as to which provider rom i should use. dcd's build looks the best to me. from what i have read about what i want to accomplish.
here is my data
software 2.17.557.0
firmware 1.61.00
hardware verson 0003
activation date mar 31 2008
device info.
rom version 2.17.557.0
rom date 11/20/07
radio version 1.64.00
i can read and i am not affraid to get my hands dirty but i didn't know which rock to start looking under.
thanks
nick
Click to expand...
Click to collapse
I have US Cellular also. Read the thread on how to unlock you phone. You will need to update your radio also. DCD 4.1.2 is the one I run and it is very good.
Start by going here
http://wiki.xda-developers.com/index.php?pagename=HTC_Titan
Or this post is more orientated to USCC
http://forum.ppcgeeks.com/showthread.php?t=24511&highlight=uscc
Howdy,it's a breeze, just a bit scary at first but well worth it. Holla out if you need some step by step. 1. get good unlocker, 2. update radio to the latest dcd's offered. 3. upload carrier (uscc, right!) it will say cellsouth but dont worry, its just a name we can fix later, then load dcd's 4.1.2 rom. Set your GPS com to 4 and baud to 4800, dont let window automatically manage, too slow.
I was wondering how your coming with all the reading. I just ran accross your post and reminds me of doing this to my uscc titan last weekend. Always write ALL of your information from EPSt (##778 send) save it as a text on your computer, easy access....If you lose any info, I've got it here on mine. Let me know how it goes, really hard to mess up, dont worry....KC
xbeergogglesx said:
I am trying to unlock my gps and have found lots of nice builds but i am confused as to which provider rom i should use. dcd's build looks the best to me. from what i have read about what i want to accomplish.
here is my data
software 2.17.557.0
firmware 1.61.00
hardware verson 0003
activation date mar 31 2008
device info.
rom version 2.17.557.0
rom date 11/20/07
radio version 1.64.00
i can read and i am not affraid to get my hands dirty but i didn't know which rock to start looking under.
thanks
nick
Click to expand...
Click to collapse
Hi friends ..
I have a problem hopefully can help me, is the following.
I have a 6800 Titan U.S. Cellular and try to upgrade the ROM DCD 3.2.6 but made the mistake to put the ROM in the SPL 1.07.000 or blocked. When completed the installation of the ROM, my phone restart but it did not run the windows just stays on a black screen that says HTC Smart Mobility and no more progress is just there. in the bootloader (3 colored screen) shows that the SPL is 1.07.0000 and even more I've tried the stick olipro 2.40 to unlock the SPL and will not let me.
When you start appearing in small red letters that said R 1.64.00, D 3.2.6
Please help me no longer do that, I think it broke. !
Copoernico64 said:
Hi friends ..
I have a problem hopefully can help me, is the following.
I have a 6800 Titan U.S. Cellular and try to upgrade the ROM DCD 3.2.6 but made the mistake to put the ROM in the SPL 1.07.000 or blocked. When completed the installation of the ROM, my phone restart but it did not run the windows just stays on a black screen that says HTC Smart Mobility and no more progress is just there. in the bootloader (3 colored screen) shows that the SPL is 1.07.0000 and even more I've tried the stick olipro 2.40 to unlock the SPL and will not let me.
When you start appearing in small red letters that said R 1.64.00, D 3.2.6
Please help me no longer do that, I think it broke. !
Click to expand...
Click to collapse
Try updating it via the micro sd card. I believe this happened to me once and that is what I had to do. Just follow the instructions in one of the previous links.
And the radio is to old for that rom.
cmf04 said:
Try updating it via the micro sd card. I believe this happened to me once and that is what I had to do. Just follow the instructions in one of the previous links.
Click to expand...
Click to collapse
when told by the method of the microsd card, refer to NueSPL 2.47? because if so, for that is required to synchronize the phone with active sync so to put the exe in any folder of NueSPL and then format the card in fat32. The problem is that my phone can not synch with the active zync, that otherwise can have a flash card 2GB believe that this affects the flasheo through titaimg.nbh because all that I have just run is the gray screen with the legend that says "Loading ..."
I too have a USCC 6800 with 2.17.557.0 and 1.64.00 on it. I am new to the whole phone flashing scene, and have spent literally all day today on these forums searching and reading. Did you get yours working, and if so, what did you end up using? The main things I am looking for are GPS support and windows mobile 6.1 instead of 6.0, if that is possible. Any help would be greatly appreciated!!!
Would the upgrade for the Alltell/Sprint versions of the 6800 on the HTC site work with the USCC version? From what I can tell they are the exact same handset, just with different software features by their respective service provider.
i just put wm6.5 on my phone, its running...OK but too slow, I'm gonna go back to dcd 3.3.4 or maybe try a different one.
I am still hesitant of changing anything with mine. I guess I am too afraid of choosing the wrong thing and bricking it. I think I have a pretty good handle on how to do it, but not so much on the various files. If anyone has a good (tested) setup, please share the links to the various files.
Just wondering, are any of you who are having problems with flashing from the Kenosha, Racine, or Milwaukee Area of WI?
If so, I may be able to help you. I go to school in downtown Milwaukee and have flashed USCC roms on my phone many times before. I could unlock your phones and flash them for you as long as you payed me for the time to do so.
Thanks
Dave
I'm over at Fennimore on the southwest.
chrialex said:
I'm over at Fennimore on the southwest.
Click to expand...
Click to collapse
Are you serious...what are the odds of finding someone on a board like this from Fennimore. I live in Fennimore.
LOL, maybe the same as finding someone you know from Fennimore, it's Coulman
No ****. how are you doing. haven't seen you in a long time. i know this is off topic. hit me up on myspace www.myspace.com/sevendust4556
This guide help me get the gps going on a us cellular 6800. I thought i broke my phone at first. just read the instructions before doing it.
http://forum.ppcgeeks.com/showthread.php?t=24511