I have read lots of threads here...trying to flash my HTC Fuze GSM...downloaded Hardspl "RaphaelHardSPL-Unsigned_190_1_3" when I run it it puts the phone in a black screen...according to the instructions its supposed to reboot and it doesn't....after w hile the RUU comes back and says error occured...try recovering etc....
i have also ran the SPL manual from my SD and tried running "RaphaelHardSPL-Unsigned_190_1_3" as soon as I run manual spl from my device...it goes to blank screen and does't reboot....
Please help...
under the 3 colour mode to flash your SPL again
that worked thanks a million
Related
Hi All,
I tried flash by wizard following http://forum.xda-developers.com/showthread.php?t=298967
Every thing went well but I was not able to HARD RESET. So instead I removed the battery and started it again. It starts up but got struck at screen which says
IPL 2.21.0001
SPL 2.21.0001
GSM 02.19.11
OS 2.18.00
Could some help me what to do now. I read some threads to go to Boot loader screen by pressing "Camera" + "Reset" button and got USB at bottom left and tried RUU with some thing available on forum but every thing failed saying "connection not established"
Please guide me to solve this problem.
if ur device is CID LOCKED "G4" u need to flash the official rom 1st then flash with any G4 safe rom available >>
USING :
ShellTool
http://forum.xda-developers.com/showthread.php?t=293480
or
SoftSPL
http://forum.xda-developers.com/showthread.php?t=329147
Thats the only way for G4 "CID LOCKED"
No...
If OS is not boot up correctly, both ways doesn't work because all of them requires to do in a working OS.
You should find your stock ROM or Wizard Love ROM, use the bundled RUU to flash it so you get the device working again, then use SoftSPL/flash HardSPL and use RUU to flash OS-only WM6 ROMs.
Yes starkwong you are right. I bought my device back working by flashing it with "wizard love" now its up and running. I would proceed with Soft SPL/Hard SPL and then try to flash it with WM6.
after update my hermes my phone dosent start windows after another upfate with a shipped rom the phone finish the update but stil dident start windows any suggest
ipl.1.01
spl 140 olipro
londere said:
after update my hermes my phone dosent start windows after another upfate with a shipped rom the phone finish the update but stil dident start windows any suggest
ipl.1.01
spl 140 olipro
Click to expand...
Click to collapse
You might need to reflash it. Hold the two soft keys and then push the reset button. it will ask to hard reset. If the phone fails to come on after the hard reset, then hold the left 'ok' key and the power button, and then push the reset under the phone- this will take you to a tricolor screen where you can then re-flash the phone. try reflashing with official rom's, before using any other roms.
yes i do but it still in boot any sugest ipl 1.01 spl 1.40 olipro if any know how to update ipl with hard spl or how to remove hard spl it will be aprecible
My suggestion would be to try using sd to reflash the rom and see if that orks. format sd card making sure its fat 32 then put .nbh file in root directory. rename to herimg.nbh then insert into phone. go to bootloader and it should start the flash straight away. if this works make sure you upgrade spl to olipro 2.10 hard spl so its easier if there are problems. you can possibly upgrade spl this way too (get nbh file and rename hermimg.nbh). I tried this on my herme 100 and it seemed to work. it will flash the spl BUT when it restarts it will go straight to bootloader and start flashing again. as soon as it restarts get the sd card out and put on the os you want to flash. insert card and as long as you've named it hermimg.nbh it should flash new os with spl olipro 2.10. Good luck flashing.
You should read the wiki first : http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
your phone can be unbricked using the information on wiki.
only enter to bootloader the ipl dosent start also i fla**** but it stil apear spl.140oli whei in flash it with hard spl 1.10 and when i flash it with spl 2.60 oli it send me a error i try to flash it with qtek-cingular-doppod roms and nothing any suggest
any fu**ing suggest?
also it avoid me to update spl im stuck on hard spl 1.40 and ipl 1.04 i try to flash hspl 260-210 but it refiuses to stay in 1.40 radio 1.27 patched the ipl works but it frezzes with the green led dosent apear nothing
my device still blocked in boot mode i dont know if it is briked the device had the following info
ipl 1.04
spl1.40 oli
radio maybe no
os no
any suggest
any sugest to save my hermes
follow the unbrick guide link that koorosh_bsboys posted
it cant be unlocked its stuck in spl 140 olipro
did you follow the unbrick guide that koorosh_bsboys posted?
just stop trying any unauthorised ideas. let me know if i can help u. i have a friend in o2 service centre here in india. he can get ur device working. he does it by help of a software and 3 cables . it takes about 2 hrs. just let me know if u want ur device to work again
stil zombie my device im getting crazy any ideas
londere said:
stil zombie my device im getting crazy any ideas
Click to expand...
Click to collapse
If you want people to help you, you have to help yourself first!
1st of all, have you gone to read the Wiki as suggested?
2nd what methods have you tried to unbrick your device?
If you can't answer these questions then we can not help you, you keep asking for suggestions but you do not even reply to other's questions!
Here's a good place to start helping yourself if you haven't already http://forum.xda-developers.com/showpost.php?p=1465974&postcount=1
hi everyone, can someone please tell me what i did wrong.
I have flashed a few roms before and this time every time i start the 8125 it gets stuck cingular raising the bar screen.
The phone will still do hard reset.
Ipl 2.25.0001
Spl 2.2.5.001
Gsm 02.25.11
OS 11.0.1.1
I tried to do upgrade it to the the TNT 19199 professional wizard v.2. I used the shell tool and dropped the nk.nbf file into the shell folder like i have always done before and this time its stuck at the same screen. I can't connect it to active sync or even the computer to put back the stock cingular rom back in. Can someone please tell me what im doing wrong, from what i understand the phone is not bricked yet because i can still do a hard reset but still sends me back to the main startup screen. Help please.
Stock ROM can be flashed from Bootloader mode, just put your Wizard into bootloader mode (Camera+reset), then run the stock ROM RUU.
thanks helped out perfectly
Same Problem
New to this...Could someone Please give me a walkthrough on how to do this.I can still hard reset.I reset using camera + reset...Brings up r/b/g screen.I don't know how to flash from there.Any help is greatly appreciated.
IPL 2.25.0001
SPL 2.25.001
OS is 10.0.0.10
I took it back to WM5.Seems to be OK.Gonna try using Wizard Service Tool instead of ShellTool.See what happens
You should HardSPL, then use RUU on ROMs without IPL directly.
Just did the titan unlocker and now the p4000 is stuck in bootloader with these 2 lines:
TITA100
SPL-1.20.Olipro
i think i need some help
thanks in advance
Marc
edit:
RUU_TITAN_SPRINT_WWE_3.56.651.0_RS_3.42.02_SPCS2.0 4_PPST_0619_Ship.exe >>> would flashing this ROM and Radio save me or my titan?
orangeworx said:
edit:
RUU_TITAN_SPRINT_WWE_3.56.651.0_RS_3.42.02_SPCS2.0 4_PPST_0619_Ship.exe >>> would flashing this ROM and Radio save me or my titan?
Click to expand...
Click to collapse
yes..............
since i'm stuck in bootloader mode, how can i use the ruu update utility ?
i'm getting connectiong failed and only option is to exit utility
any ideas ?
if u are in bootloader connect the usb cable and the phone should say usb at the bottom, just open up the ruu update and it should work just fine
Error 264
update utility cannot connect to your pda
and it says USB on the bootloader screen
SPL is 1.20 olipro
take your SD card out if (with phone powered off) if u have an image on the SD card and retry
no SD card being used at the moment
edit: it seems now it is flashing...
let's say this does work, fact that i'm putting a sprint ROM on my telus phone is gonna be alright?
re-edit: crashed at 11% - invalid command error 290... RUU encountered a communication error
recovery
at 11%, titan reset and went back into bootloader mode, RUU crashed but gave option for recovery which was "successful"
retried the same RUU_TITAN_SPRINT_WWE_3.56.651.0_RS_3.42.02_SPCS2.04_PPST_0619_Ship.exe
and crashed again at 11%
i think i killed my phone
i can't seem to do anything, not the telus wm6.0 ruu nor the one stated earlier...
is there a way i can revert to my previous SPL 1.04 ?
really appreciate the help @ 5:35 AM
got my telus wm6 to run and then decided to up to olipro 2.40
now it won't got past second splash...
radio is 1.32, rom is dcd 3.2.5
now from my understanding of what i've been reading is that i need to revert to olipro 1.20 to be able to flash my radio
and i can't do that since i can't get activesync.
any ideas ?
Get a SD card. Go to WIKI and following reverting to Stock. Then start over on flashing. I have done as you did and fixed the phone.
your phone sounds jacked up, how long is it stalling at 11%, r u giving it decent enough time?
redownload the latest sprint rom from htc america here:
http://216.139.227.226/RUU_TITAN_SPRINT_WWE_3.56.651.0_RS_TITAN_3.42.02_SPCS2.04_PPST_0718_Ship.exe
let it run for at least 20 minutes before deciding it crashed...after 1st boot softreset before letting it run any customizations
I was trying to follow instructions here: http://forum.xda-developers.com/showthread.php?t=395945 to unlock my phone, I got as far as flashing the radio but at 95% done.. it failed. I have tried taking the battery out, hard resetting the phone but now whenever I go to flash the radio with 1.00.000.0 (in the instructions above) or my original radio 1.58.16.27 - it gets to the percentage screen and just hangs on 0%, then the ROM update utility says its failed. I've well and truly messed it up - when using the ROM update utility it's blank under current image version now and whenever I power on the phone it's always on the following boot screen:
NIKI200
SPL-1.16.0000
CPLD-4
I just can't do anything with it, help!!
Any help is much appreciated! Thanks
Try to flash the original rom
Have tried this, it does the same thing.. just hangs
Read this thread http://forum.xda-developers.com/showthread.php?t=390606
Thanks for your help, MTTY sorted this