Hi all,
My jasjam showing "no GSM" error after i upgrade it to shaps.4.22 & telestra & stain normal & Dvh-V-24 & Cic-13-
normal when those roms works about one year.I have (no gsm error & no protocol & no IMEI ) about one week.
I read many webpages in Xda-... & try many ways but steel have those errors.
My device os can boot(shap's 4.22 )
Model: Jasjam
ROM Before Flash:I dont know
Radio Before Flash: I dont know
Bootloader Before Flash: I dont know
Current ROM: shap's 4.22
Flashing Radio:
Current Bootloader : 2.1 olipro & can change to 1.04 With micro sd
CID : i think super cid
Radio Corrupt: Yes
No GSM Error: Yes
Stuck In Bootloader: No
Stuck On Windows Mobile Splash: NO
Can boot into OS: Yes
Tried mtty command Rtask: error comannd
Which radio/rom (rom with radio on it on NBH format only ) must I install on it.
The telstra roms that I downloaded from club-imat cant install(how van i change this roms to nbh roms ?? )
What should i do next? Thanks every body
Try installing a shipped rom, you should be able to locate it in the wiki.
Cheers...
I can help you solve in China
Related
HI
I AM IN NOW BIG TROUBLE
I HAVE O2 WITH SPLASH ON SCREEN AND HANGS THERE
all i done is upgarde downgrade from version 1.600 /1.66/1.72
all giving same errors
error 114 while erasing radio rom
this is RUUL LOG
9:54:14 Write block133
09:54:19 Update Stage 3 complete
09:54:34 Begin Stage 4
09:55:04 Radio Erase retry 1
09:55:34 Radio Erase retry 2
09:56:04 Radio Erase retry 3
`
THEN ERROR
NEED GUIDANCE
its a nogsm on screen
No GSM
1.72 wwe
thanks
no one has problem before ?
how to do with mmc card
why lauch vwrsion does not communicate with xdaII
i got Xda_II_LaunchROM_v10311
alos Xda_II_Upgrade_v16050
but this two cant communicate
also i put himupgradeUT in same folder but it gives error bed chacksum
i am becoming crazy now
OK.. can u tell me what version you have now? and what version are you trying to upgrade.. lets make this step by step.. i will try my best..
srtange
i had put my phone on charger after two hours
windows start up scrren appeared
also if i allow to reset phone hangs on O2 screen
its work ok now but without gsm
this is information
i got O2 XDAII
ROM VERSION 1.72.00WWE
ROM DATE 03/15/04
RADIO VERSION NOT AVIALABLE
PROTOCOL VERSION NOT AVIABLE
ExTROM VERSION 1.72.181
IDENTITY
Model No. PH10B
Platform: pocket pc
imei: not aviable
i cant flash radio part
my boot loader is 1.03
thanks and regards
Oh My God i dont know how to upgrade the bootloader... i think the problem is your bootloader cuz its not updated.. it sgould be 1.06 and all of that will work fine.. i dont know how to upgrade the bootloeader...
This is my experience with my dead Hermes.....wich back to life
my case is:
my Hermes is an Imate JasJam loaded with TNT ROM ( WM6 ) with IPL-100 and SPL-1.04
1- during uptating the Radio the upgrade stop due to something wrong in the USB connection
2-i got a Hermes with these error :
A: Bootloader is OK
B: NO GSM
C: Operating system stop at first screen and not booting at all
The solution:
i did anything you can emagin with no success....loading another Radio( Failed )....loading another ROM ( Failed )...
What i did:
i used the new HTC wm6 ROM....which started to flash my Hermes without problems...it first loaded the SPL from 1.04 to 2.03 and after that start to flash the ROM and i stucked at the error ( INVALID VENDOR ID )......
here is the steps now:
1- use the new HTC ( wm6 ) ROM...the latest one as i did...this one will change the SPL to 2.03
2- get yourself the original 2005 ROM that fits your MFG ( Imate,O2.....etc)
which also incluse Radio as a deafult.
3-extract this rom to the separet files ( using WinZip or WinRar )
4-take the .NBH file of this ROM
5-extract the HTC ROM you used at step (1) and replace the .NBH with the from the ORIGINAL ROM ... this step will pass the (INVALIED VENDOR ID ) error.
6-the upgrade will go very well and now you will have a Hermes with WM2005 on it.
that is it......you got your device back...and now you can do anything with it...and upgrade it to any operating system.
Regards
Sherif
He Guys,
Just my luck I have bought an HTC Tytn with the original Dutch rom and sim unlocked second hand.
I wanted to put a new Dutch rom from HTC on it but I keep on getting the ERROR [244] : INVALID MODEL ID but what I don`t understand is I have used the original Dutch rom from HTC. So I checked the device information and under the tab identity it says;
Model No.: H
Platform: PocketPC
IMEI: xxxxxxxxxxxxxxxxxxx
Shouldn’t the Model No. be HERM200?
Has anyone any suggestions in how I can solve this problem so I can flash any rom I wish.
I have tried al the cid unlock programs I could find and in bootloader it says;
H
IPL-1.01
H
SPL-1.40.Olipro
Thanks in advanced.
Use RAR to unpack the Original Dutch ROM.
Take the NBH file that you get when you unpack the ROM.
Put it in a folder with CUSTOM_RUU from Olipro.
Run CUSTOM_RUU and it will load up the ROM from the NBH file, bypassing the CID check. Should work
Thanks for the reply,
I have tried what you suggested but I still get ERROR [244] : INVALID MODEL ID I have also read these posts http://forum.xda-developers.com/showthread.php?t=322231&highlight=CUSTOM_RUU+from+Olipro and http://forum.xda-developers.com/showthread.php?t=322119&highlight=CUSTOM_RUU+from+Olipro and http://forum.xda-developers.com/showthread.php?t=309707&highlight=CUSTOM_RUU+from+Olipro and tried these suggestions but every time I get the error message. The radio update process was the same for me it will go to 7% and then give the message ERROR [244] : INVALID MODEL ID.
I have also tried the HTC_Hermes_SIM_CID_Unlock_v3a and Hard-SPL-V7 but still get the error message.
I hope I’m doing something wrong if not then I hope you have a new suggestion.
Thanks in advance.
Please set your device in BOOTLOADER MODE and post here your IPL / SPL versions.
Junner2003 said:
Please set your device in BOOTLOADER MODE and post here your IPL / SPL versions.
Click to expand...
Click to collapse
Did you read first post?
VivaErBetis said:
Did you read first post?
Click to expand...
Click to collapse
Ups, missed the bottom - thought it is the signature already! Sorry, haven't had my coffee yet!
Well, looks like the device is CID unlocked!
How about trying to flash an entire cooked ROM?
i would suggest the following:
flash a cooked rom (any)
see if that makes any difference to your model id
then try and flash the native dutch rom
good luck
Hi Guys,
As you suggested I tried a cooked rom the Hermes_WM6_vanilla still get the same error message when I put my device manually in boot loader it shows;
H
IPL-1.01
H
SPL-1.40.Olipro
But as soon as I try an official or cooked rom it shows;
H
IPL-SSPL by des
H
SPL-1.09.ds
I’m now trying Schaps_WM6Pro_WWE_4.00_Full_Beta3.exe and choose for auto detect and it said 1.40 Olipro and in boot loader it shows;
H
IPL-1.01
H
SPL-1.40.Olipro
And after 1% I got the ERROR [244] : INVALID MODEL ID message again.
I think my options are getting slim.
Your ModelID is stored on NAND and can be edited quite trivially (mostly).
how it got corrupted I don't know, however, the important question is; can you get into the OS?
He Olipro,
The device it zelf works perfect I can go anywhere I want even in the OS.
Just lead the way.
Changing Model ID
I have a similar problem in that my Model ID got corrupted during a radio upgrade. I now get the same error (244) and am stuck on SPL2.10 and can't downgrade to fix it. Can anyone tell us how to manually change the model ID in the NAND?
Much appreciated.
Dumping NAND
Ok, I'm a relative newbie so appologies before I get flamed. Thanks Olipro for giving me a clue.
I have now got spl 2.60 on my device but am unsure how to dump the NAND. I've worked out how to dump the 3 partitions from the device to dump the OS but am still unclear which part of the device is the NAND. I've read the Wiki on the memory map but am still not too sure.
Anyone able to give me simple instructions to dump the NAND and once I've done that where abouts is the ModelID stored? Do I do this using mtty?
Thanks in advance.
http://forum.xda-developers.com/showthread.php?t=322225
NAND Dump
Thanks Drummer for pointing me in the right direction.
Ive done this bit:
BTW, if you want to do a full backup of you FULL eeprom nand at any time, connect as before and type these commands:
plink HERMES > full.nb (hit ENTER twice)
task 32 (hit ENTER once and only once from now on after every command)
password 0000000000000000 - My device password is BsaD5SeoA which I used instead.
set 1e 1
rbmc me.txt 50000000 7fff800
watch your file grow to 128 MB.
It creates a full.nb file but it stays at 1k!!
** Note I have copied the bootloader file for spl 2.60 on my Hermes and ran that so I can now use that versino instead of the 2.10 thats on my device if that makes a difference and have tried with no joy with either version. Yes I know it says to use 2.30 but I can't work out how to get that on my device due to the ModelID error.
The Model number is contained within the herm1.nb file that was posted by BusStop in that thread. No need for complete NAND reflashing, only that section. You'll see it using a Hex Editor. You should write down your WiFi MAC addess, so you can edit it before flashing the file with the corrected Model number. Now you just have to figure out how to get SPL 1.01 MFG on your device...
Thanks Drummer. I did try flashing the herm1.nb file but of course as I do not have SPL 1.01 MFG it gievs an error. I'll keep trawling through the site and see if I can work out how to get SPL 1.01 onto my device. I'm not going to let this damn device beat me.
Ok so I worked out how to get the ModelID using getdevicedata. Used nbhtool to create a vaild nbh using the ModelID I'd just got and used the spl from 2.30 and it updated that fine.
Excellent.
However did the same with the MFG1.01 and flashed it and......
I now have a dead brick, no power and no response form usb. Time to get a replacement device.
Thanks for all the help I've had. I'm sure it should have worked.
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber
5.) Soft Reset
Thanks for the advice Drummer however:
1.) Remove battery
2.) Connect Hermes to charger or USB
3.) Insert the battery while Hermes is connected to charger
4.) Red light should turn Amber - Nope red light goes out!
Mne shows HHHHHHH
Hi all, i've upgraded my radio and after my model id changed to H.
So, reading some posts i've used NBHTOOL.
1.I've decompiled an original Italian ROM
2.i've obtained a custom nbh selecting only OS and EXTROM and changing my Model number.
3. after that i've flashed the nbh resulting into a write error at 84% and a bricked htc.
Luckily i was able to reflash roms and i processed to second experiment.
I've made a custom rom with only the os, and it WORKED!
so my questions are:
1. can i use my htc even if my external rom isn't flashed (it cames from an old Schaps 4.0 succesful flash)
2. It is safe to proceed installing bootloader SPL using the nbhtool like i did with the os?
In that case i will be able to fix the model id problem by flashinh spl 1.01 and using the wireless fixing method you posted..
Thanks in advance for your reply!
Hi
From my understanding the Ext rom is mainly used for carriers to install there specific addons and customizations so it shouldn't be a problem.
As you can see I did flash spl 2.30 using this method and it worked fine ti was only when something whent wrong flashing 1.01 that my problem happened but I think that may be that I used an nbs file instead of an nb file from what I've read since.
Good luck.
Edit: Just noticed someone on this thread has managed it by going straight ot 2.60 http://forum.xda-developers.com/showthread.php?t=322225
Hi, I've got this problem:
My device: HERM300 (T-mobile MDA Vario II)
IPL: 1.01
SPL: 2.03
No KITL
No MTTY
Errors while flashing ROMs (260, 270, 274, ) via USB
Errors while flashing ROMs via SD card ( numbers in red 00028002 or error 00068002) so it's impossible. I don't know if it is HardSPL, but I know that it's impossible to flash any ROM (including CID unlocking + HardSPL + original + cooked ROMs)
I tried everything possible, except JTAG, so, if you have any other advice, Help me please....
P.S. Bootloader works, but it's unable to load any ROM
Edit: Original shipped ROMs gives me Error 294 - Invalid Vender ID
you need to found your phonecompany country rom original
hii,
I bought a HTC HD2 from a friend with a broken LCD.
He walked with his HD2 in his pocket against a table and it cracked.
If you push a little on the screen you still can see allmost everything.
so here is the problem:
I try to boot it but I've got a black screen with a white triangle...
I did some research on google en tried a soft reset bij holding de up and down volume en start up the phone, it was succesfull. But the problem didn't solved.
Than I did the thing with only the volume down button and this is what i get.
a screen with 4 collors.
HX-BC
SPL - 1.42.0000 XE
MicroP (LED) 0x05
MicroP (TOUCH) 0x30
Upgrade rom code error please try again...
someone knows what to do ?
I really need some help.
Many Thanks..
What is your phone type?
HD2 with 512rom or TMobile ?
If you flash with official rom. Below are the serial numbers you may need to download the rom from official website.[I quoted from mskip]
World Wide English (WWE) - Serial: HT9AZNW00968
South East Asia (Asian WWE) - Serial:HT01XNW03437
Denmark: (DAN) - Serial: HT9B6NW00167
Norway: (NOR) - Serial: HT9C7NW01234
France: (FRA) - Serial: HT9BLNW00122
Spain: (SPA) - Serial: HT9BDNW00592
Italy: (ITA) - Serial: HT9BCNW00722
Greek: (ELL) - Serial: HT9BMNW00059
Germany: (GER) - Serial: HT9B9NW00374
Netherlands: (NLD) - Serial: HT9AVNW01232
Russian: (RUS) - Serial: HT9BCNW00012
Turkey: (TUR) - Serial: HT9CMNW05766
East Europe: (WWE_EastEurope) - Serial: HT9B3NW02204
*If you want to flash with custom rom.
Read below thread.
http://forum.xda-developers.com/showthread.php?t=609477
Go to HTC's website and download an updated ROM. You will only be allowed, with your phone's serial number, to download a ROM that is suitable for your phone.
It can't be a tmous with working spl 1.42.
It's been SD card flashed with an incorrect stock Rom whilst hspl was installed so updated the spl , removed hspl and then the flash failed.
Either find and flash the correct stock, or go straight to hspl2 and flash what you like. Usb flashing from bootloader will be fine in either case.
Well try to get the stock rom flashed...
Sent from my HTC HD2 using XDA App
Download the Stock ROM from HTC's website for the country the phone was purchased from. It should work flashing via SD Card method.
No way to flash stock rom
Hi,
I have an HTC HD2 bought in austria in sept 2010. since march 2011 i flashed to HSPL 2.08, Radiorom 2.15.50.14, MAGLDR113 and a Android NAND.
2 weeks ago i tried to upgrade to new NAND Version and my HD2 brocked. I´ve tried zu flash with stockrom by usb AND sd, but nothing worked. Tryed to flash by usb with org. HTC_GER_3.14.407.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship.exe and get an Error 290 at 8%. After that i´ve tryed leoimg.nbh in root of SD by renaming RUU_signed.nbh form that rom.
Starting in Bootloader I read "Upgrade ROM code error Please try again" but it does not load the image from SD.
Any ideas?
thx in advanced
try using hspl 2 , 3 and 4 to remove the spl 2.08.hspl first, my first try would be hspl2 - choose 1.66.0000, and then flash the stock rom from sd card, and my second attempt if that didnt work would be hspl4 - choose 3.03.0000
hi again,
i tryed to flash with all versions of hpsl 2,3 and 4, but nothing works.
last try was hspl 2, 1.42.0000 an flashing by usb.
it was working to 100%, reboot and i get a whitescreen with htc logo.
thats all.
after 1 hour reboot, but nothig, only whitescreen with logo.
flash by sd don´t work anyway.
In that case, and especially since the failure happened at 8%, I'd say you have the stuck radio issue, (which seems to be happening a lot more than usual lately...)
Symptoms are usually spl seemingly flashing but hasn't changed when you check in bootloader, plus flashing failing at around 8 or 9%.
You may be able to flash cooked roms which don't include radio or spl, and you may be able to flash android, but may well get fatal hit errors,, it's not always the same. I suspect bad memory blocks or corrupted radio (or both, perhaps they are the same thing)