Hey I have an HTC Touch Pro (CDMA, Spring)
I haven't flashed it with a new rom in a long time and want to upgrade again.
I have Hard SPL 0.37 CMONEX
I really liked the Juicy 8 rom but all the roms i've tried putting on here aren't working.
What do I need to do to flash a new rom? Yes i've wiped the phone, and yes i'm in the bootloader. Does it need an updated Hard SPL?
Once you have unlocked your phone, with the HSPL Tool, you shouldn't be having a problem. More information is needed. What happens when you are in the bootloader screen? have you tried renaming the nbh file to RAPHIMG.nbh and putting it on your SD card and installing it from there? Just for craps and giggles, have you tried Reinstalling to a stock ROM to see if you can do that? the Stock ROM from HTC.com will install whether you are locked or not.
Related
I accidentally flashed the titan using olipro 1.2, and the new unlocker, and I cannot get past the verizon boot screen. This is a fresh new 6800. when I start it it says:
p DCAAXAM-4350
R 3.42.30
D 2.17
The bootloader screen says Tita100 spl-120.olipro
the only way I can flash is via the sd card. I cannot connect via activesync.
how do I fix it?
this is a warranty replacement, so I need to get this to work before I restore my old 6800 to factory settings, and return it to verizon
thanks
whiteblazer01 said:
I accidentally flashed the titan using olipro 1.2, and the new unlocker, and I cannot get past the verizon boot screen. This is a fresh new 6800. when I start it it says:
p DCAAXAM-4350
R 3.42.30
D 2.17
The bootloader screen says Tita100 spl-120.olipro
the only way I can flash is via the sd card. I cannot connect via activesync.
how do I fix it?
this is a warranty replacement, so I need to get this to work before I restore my old 6800 to factory settings, and return it to verizon
thanks
Click to expand...
Click to collapse
Can you not put the phone in bootloader mode (power+camera+reset) and connect via USB? Even though activesync doesn't see it, it's still possible for RUU updater to connect. I had a similar problem before. Try doing this and putting Hard_SPL 2.4 on it.
Look at section II on this wiki... it says if you have 1.20 olipro... flash to an older rom and radio... WIKI
Snippit.... " if it is 1.20 then you have the pre-GPS ROM bootloader and must first flash to one of the older ROMs and associated radio to boot into WM, get an ActiveSync connection and then upgrade to 2.40. "
nitro66215 said:
if it is 1.20 then you have the pre-GPS ROM bootloader and must first flash to one of the older ROMs and associated radio to boot into WM, get an ActiveSync connection and then upgrade to 2.40. "
Click to expand...
Click to collapse
Hes right, you need to load an old pre-GPS rom on your phone, then upgrade. I've had this happen myself.
Yes, this is what I saw too, however, all the roms I found on this page http://wiki.xda-developers.com/index.php?pagename=TitanOtherHome for the olipro 1.20 take me to an internal server error on fileshex.com. I can't find any rom file that I can actually download. Does anyone have a link to one or can you upload it? I suppose it doesn't matter which one it is, since I'm going to upgrade from there.
I just cooked an old 1.6.7 rom for you...wow did it bring back old memories.
Download 1.6.7 rom here: http://www.cinconet.org/titan/dcd 1.6.7 Rom.zip
Download 1.30.60 radio here: http://www.cinconet.org/titan/Titan Radio 1.30.60.zip
Put radio .nbh on the root of the card with a card reader. Force phone into bootloader and flash radio first. When it completes, remove the microsd card and replace the radio .nbh with the rom .nbh with the card reader. Insert the card again, force bootloader, and flash the rom. Remove the card and soft reset.
WOOOOOOOOT!!! it worked! Thanks gc14 for the files and awesome instructions!
I just upgraded the bootloader on my phone from 1.04 to the 2.4 in order to upgrade the rom. After the bootloader upgrade finished however, my phone will not boot back into the OS. Each reset brings me right back to the bootloader screen. How do I proceed?
JJohnson911 said:
I just upgraded the bootloader on my phone from 1.04 to the 2.4 in order to upgrade the rom. After the bootloader upgrade finished however, my phone will not boot back into the OS. Each reset brings me right back to the bootloader screen. How do I proceed?
Click to expand...
Click to collapse
Flash a stock gps rom and then flash any custom rom you like.....if that does not work try the exit bl program....
flyers2114 said:
Flash a stock gps rom and then flash any custom rom you like.....if that does not work try the exit bl program....
Click to expand...
Click to collapse
Each rom flash starts with opening an activesync connection.... I cannot get the OS to load. would the exit bl fix this?
You can download a GPS compatible radio and a GPS compatible ROM and flash them from SD card, this is actually very easy to do. Once they are both flashed on the phone, then you can flash whatever GPS compatible rom you want via Activesync. For now tho, since it won't boot, the SD card is your best option.
They end in .nbh, so look around, there are 2 posts one for the latest radio and one for DCD's latest rom, both should have links to .nbh files, and if not, you can rename the RUU file out of the DCD rom and then copy it to your SD card.
There are dozens of tutorials on here, just do some searching and you'll be ok.
BTC
BillThyCat said:
You can download a GPS compatible radio and a GPS compatible ROM and flash them from SD card, this is actually very easy to do. Once they are both flashed on the phone, then you can flash whatever GPS compatible rom you want via Activesync. For now tho, since it won't boot, the SD card is your best option.
They end in .nbh, so look around, there are 2 posts one for the latest radio and one for DCD's latest rom, both should have links to .nbh files, and if not, you can rename the RUU file out of the DCD rom and then copy it to your SD card.
There are dozens of tutorials on here, just do some searching and you'll be ok.
BTC
Click to expand...
Click to collapse
Thank you so much for your help! I spent a couple hours looking around. Copied the radio .nbh to the SD, let it load, reset, copied ROM .nbh to SD, let it load, reset. and I'm up and running.
Thanks again.
Glad things worked out.
BTC
Like the title says, im just stuck at bootloader and instead of booting to the white screen it just stays on bootloader and says "SERIAL".
Ive googled, youtubed, and searched here, and many have the same problem, but i have yet to seen a solution to this.
I have tried android and many custom roms, and now im back on original ROM and everything works great. BUT i have HSPL in my phone and i dont want it for now.
It is a very easy procedure in the guides and should not be a problem, but please how can i get my LEOIMG.nbh to boot from my memorycard?
It is formated FAT32, and i have tried redownload the stock rom and unpacked it with winrar several times, but the result is always the same.
Is there some way to go around this? I Just wanna boot from the memorycard and restore my phone.
FYI, the restore is just for warranty issues.. I just want to be able to go back just to be on the safe side..
Then after that i can try the cooked roms all days
Thanks!
What size is the microSD card? As there has been reports of problems flashing from 16GB cards.
While in bootloader mode, you can plug in the microUSB and the 'Serial' should be replaced by 'USB'. This means that you can run the flashing from the computer (just ignore the requirement for ActiveSync).
Thanks for the quick reply!
I have a 8 GB memorycard.
Just before i read your post i inserted the usbcable and the screen on my htc says "USB".
But how do i uninstall HSPL from my PC in usbmode? Use customRUU and place LEOIMG.nbh in that folder?
If you install either the HTC Stock or your mobile provider's ROM (what ever you need for warranty requirements), they will flash your phone with SPL, ROM and RADIO.
These ROMs are avaiable from your mobile provider's website or via a link in the ROM Section.
Sounds great!
So i just run the original .exe file from my PC when my HTC HD2 is in bootloader screen in USB-mode, correct?
I have alreade flashed with original rom from PC when my phone was online. But then the HSPL did not go away even though my original rom was installed.
I could use alittle help too
when i try to update it stops at 4% tried to flash other energy roms with the same issue. don't know what todo to get past 4%
fred_up said:
If you install either the HTC Stock or your mobile provider's ROM (what ever you need for warranty requirements), they will flash your phone with SPL, ROM and RADIO.
These ROMs are avaiable from your mobile provider's website or via a link in the ROM Section.
Click to expand...
Click to collapse
won't flash the spl over usb whilst hspl is installed.
H4z3 said:
Sounds great!
So i just run the original .exe file from my PC when my HTC HD2 is in bootloader screen in USB-mode, correct?
I have alreade flashed with original rom from PC when my phone was online. But then the HSPL did not go away even though my original rom was installed.
Click to expand...
Click to collapse
use the hspl.exe program to remove hspl just like you used it to apply it. just choose a stock spl instead of the hspl.
example, regular hd2, wants to go back to o2 stock everything.
run hspl2, choose 1.66.0000
run the o2 1.72.exe rom over usb.
all done.
if the rom doesn't flash its not the correct stock rom.
samsamuel said:
use the hspl.exe program to remove hspl just like you used it to apply it. just choose a stock spl instead of the hspl.
example, regular hd2, wants to go back to o2 stock everything.
run hspl2, choose 1.66.0000
run the o2 1.72.exe rom over usb.
all done.
if the rom doesn't flash its not the correct stock rom.
Click to expand...
Click to collapse
At first i used HSPL 3 to install 2.08.0000 HSPL.
But if i run that file again i only have the choice 2.08.0000.
I downloaded a previous version of HSPL, and there i could choose SPL 1.42.0000 wich was my original SPL version before the flash.
Is this a correct way to do this?
I am asking again because even though i now am at the original ROM and Original SPL version the Radio and Protokoll-version differs from the versions when i bought the telephone.
radio and protocol doesn't matter. yes you've done it right. so long as its a stock rom and the spl ends 0000 then it's fine.
Ok thanks!
Then everything is ok now and i am very happy for that, so thanks for all answers!
I can also add that i took my original SD-card (2GB) and put the LEOIMG.nbh on it.
The bootsequence then started ok when holding down volumebutton and power on.
But the result was exactly the same as it was when flashing to stock SPL with HSPL2 utility.
So the booting-problem was memorycard related.. So it seems that even some 8 gb memorymodules have problems.
Just thought you should know.
Hi all
Apologies if this has been covered before but I cannot find anything thus far. I upgraded my HTC HD2 (Vodafone branded) from 1.72 to 3.1.4. As the device was branded I had to use HSPL (version 3) as Vodafone had no specific version, at that time, and thus used the generic HTC version as it was all that was available at that time. This seemed fine until I hit the, what I now know to be the memory issue, with this combination. At this point after trying a number of custom ROM's, I am using a Dutty Custom ROM (V12, COM2). I decided today, as I just discovered that Vodafone now have their own specific 3.1.4 ROM update available I would flash the 3.1.4 ROM, which I was able to download legitimately from the HTC web site, using my serial number.
I first flashed the stock ROM in the vain hope that the Vodafone had fixed the memory issue. They haven't and thus I decided to remove HSPL. I did this from the installation program and chose the 0000 option which removes HSPL. I then rather stupidly decided to run a task 29, which of course, failed at 0% and just hung totally. It did not time out after 10 minutes, at which point I had no option but to remove the battery and data cable. Fortunately the phone booted up and ran normally. I thus decided to re-flash with the legitimate Vodafone 3.1.4 ROM. as the memory issue still persisted. It failed at 0% just as with the task 29. I now cannot flash ANY Rom unless I install HSPL. I have only tried version 3 thus far.
Any ideas how I can get my phone loaded up with my genuine 3.1.4 Vodafone branded ROM without HSPL and thus avoid the memory issue and load genuine ROMS and updates please? For now I am back to using the Dutty V12, COM2 ROM. Any ideas most gratefully recieved and apologies if this has been covered before.
Many thanks in advance.
Regards,
Paul Lemonidis.
Try flashing to HSPL 2 not 3, and read this thread
http://forum.xda-developers.com/showthread.php?t=609477
Russ
Flash your vodafone stock ROM over SD.
And to be able to install custom ROM, use SSPL_RUU
phone into bootloader
connect usb
run hspl2
choose 1.66.0000
when phone restarts immediately re enter bootloader
run the voda 3.14 rom flash over usb
Thanks
I flashed from an SD Card and all was well. I can now reflash the same version, which I could not before, without HSPL. Thus for the moment I no longer need HSPL. Thus my warranty is valid again and I have a stable phone with the latest correct vendor ROM. I may try a custom ROM again at some point in the future if I experience problems but at least I can say I gave it a fair chance.
As a sideline, Swype works beautifully with this ROM.
Once again many thanks in advance.
Regards,
Paul Lemonidis.
samsamuel said:
phone into bootloader
connect usb
run hspl2
choose 1.66.0000
when phone restarts immediately re enter bootloader
run the voda 3.14 rom flash over usb
Click to expand...
Click to collapse
hi
i am facing the similar issue, cannot revert back to branded ROm it does not boot any further than HTC logo, will the goldcard can do this,,, aslo my branded ROM is 1.72.82124, and reason i want to put back on is that my phone memory after installing custom rom is always less than 12mb then go below 1 mb in few hours..
tried hspl, sspl etc nothing works..
netvpn7 said:
hi
i am facing the similar issue, cannot revert back to branded ROm it does not boot any further than HTC logo, will the goldcard can do this,,, aslo my branded ROM is 1.72.82124, and reason i want to put back on is that my phone memory after installing custom rom is always less than 12mb then go below 1 mb in few hours..
tried hspl, sspl etc nothing works..
Click to expand...
Click to collapse
Take the 1.72 ROM and use the flash from the SD Card method. This will get you back your memory.
The reason for the memory problems is a combination of 3.14 ROM and HSPL.
I currently have a MIUI android ROM installed but want to go back to WinMo 6.5 (stock). Now when i try to flash the ROM like i did before, its says on my PC USB Init failed, connection problem. The bootloader screen does say usb. Also when I try to flash trough the MAGLDR flash modus there is USB standing but i cant flash. I've also tried flashing the stock ROM from my SD card as an NBH file but it wont work.. Also repartitioning and all the stuff dont work because they all have te connection problem. I have tried multiple USB cables. Anyone know a solution??
you say that the SD flash doesn't work, can you elaborate a bit more?
explain everything you did, what ROM did you try, if you can give me the whole step by step you tried to SD card flash, including and file name changes etc
SD flash is usually the last resort and if you tried it with a genuine original Stock ROM it should work, albeit it will change the RADIO, SPL and ROM at the same time...
Hello,
I intend to downgrade my hd2 Europe version, from Android with Magldr, to stock Rom,
because of some bootloops i encounter after trying install wp7, so i want to start from scratch and try flashing wp7 or Android again!
I have HSPL 2.08 and i want to flash a Greek Stock Rom
(RUU_Leo_S_HTC_ELL_3.14.482.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship)
OR
(HTC HD2-RUU_Leo_HTC_ELL_1.66.482.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship_2).
My radio is 2.15.50.14.
So far i have made some research and i understand that:
1st. i must flash a stock Rom from SD.
2nd. The hspl will be replaced with stock SPL. Do i need to flash HSPL 3.03, as 3.14 ROMs on HTC HD2 Eu require SPL 3.03.0000 or HSPL 3.03, before flashing stock Rom from SD? What about 1.66 Rom?
The stock SPL version depends from the Rom which i would choose, or will be the same?
after that I just need to run HSPL4, install HSPL2.08 and continue with Magldr as i have done in the past?
Is there something I should be extremely careful so as not I have a fatal problem?
Thanks in advance everyone who will help a confused man!!!
(i don't wanted to start a new thread, so i posted here because of the title)
cmour said:
Hello,
I intend to downgrade my hd2 Europe version, from Android with Magldr, to stock Rom,
because of some bootloops i encounter after trying install wp7, so i want to start from scratch and try flashing wp7 or Android again!
I have HSPL 2.08 and i want to flash a Greek Stock Rom
(RUU_Leo_S_HTC_ELL_3.14.482.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship)
OR
(HTC HD2-RUU_Leo_HTC_ELL_1.66.482.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship_2).
My radio is 2.15.50.14.
So far i have made some research and i understand that:
1st. i must flash a stock Rom from SD.
2nd. The hspl will be replaced with stock SPL. Do i need to flash HSPL 3.03, as 3.14 ROMs on HTC HD2 Eu require SPL 3.03.0000 or HSPL 3.03, before flashing stock Rom from SD? What about 1.66 Rom?
The stock SPL version depends from the Rom which i would choose, or will be the same?
after that I just need to run HSPL4, install HSPL2.08 and continue with Magldr as i have done in the past?
Is there something I should be extremely careful so as not I have a fatal problem?
Thanks in advance everyone who will help a confused man!!!
(i don't wanted to start a new thread, so i posted here because of the title)
Click to expand...
Click to collapse
just follow the guide on the relevant ROM that your interested in
but if your playing with WP then use HSPL 2.08
if your flashing a stock ROM via SD as you pointed out it will replace the SLP with the one that comes with that ROM, so it doesn't matter what you do, then you can use HSPL4 to install the required version for the ROM that you want to use. You can use HSPL 4 to revert back to a stock SPL as well, but if you have any doubt at all then just re flash a original stock ROM, you cant go wrong at all then
Well, if i try to flash anything from my pc it says connection error. When I use flasher modus the HD2 freezes and i need to pull out the battery. I also tried flashing the stock ROM from my SD card but that also doesnt work. I use MAGLDR 1.13 and HSPL 2.08 i think. The current ROM is MyMIUI V11.
i managed to install the stock rom but now i cannot install magldr. When i start the installation the hd2 shows bootloader, then goes into the installation screen but after 1 second it flashes back to bootloader.. any help?
are you putting the phone in to the tri coloured bootloader with the word "serial" at the bottom? plug in to a USB port and the word changes to "USB" then install MAGLDR?
just so im clear what you have tried