Like the title says, im just stuck at bootloader and instead of booting to the white screen it just stays on bootloader and says "SERIAL".
Ive googled, youtubed, and searched here, and many have the same problem, but i have yet to seen a solution to this.
I have tried android and many custom roms, and now im back on original ROM and everything works great. BUT i have HSPL in my phone and i dont want it for now.
It is a very easy procedure in the guides and should not be a problem, but please how can i get my LEOIMG.nbh to boot from my memorycard?
It is formated FAT32, and i have tried redownload the stock rom and unpacked it with winrar several times, but the result is always the same.
Is there some way to go around this? I Just wanna boot from the memorycard and restore my phone.
FYI, the restore is just for warranty issues.. I just want to be able to go back just to be on the safe side..
Then after that i can try the cooked roms all days
Thanks!
What size is the microSD card? As there has been reports of problems flashing from 16GB cards.
While in bootloader mode, you can plug in the microUSB and the 'Serial' should be replaced by 'USB'. This means that you can run the flashing from the computer (just ignore the requirement for ActiveSync).
Thanks for the quick reply!
I have a 8 GB memorycard.
Just before i read your post i inserted the usbcable and the screen on my htc says "USB".
But how do i uninstall HSPL from my PC in usbmode? Use customRUU and place LEOIMG.nbh in that folder?
If you install either the HTC Stock or your mobile provider's ROM (what ever you need for warranty requirements), they will flash your phone with SPL, ROM and RADIO.
These ROMs are avaiable from your mobile provider's website or via a link in the ROM Section.
Sounds great!
So i just run the original .exe file from my PC when my HTC HD2 is in bootloader screen in USB-mode, correct?
I have alreade flashed with original rom from PC when my phone was online. But then the HSPL did not go away even though my original rom was installed.
I could use alittle help too
when i try to update it stops at 4% tried to flash other energy roms with the same issue. don't know what todo to get past 4%
fred_up said:
If you install either the HTC Stock or your mobile provider's ROM (what ever you need for warranty requirements), they will flash your phone with SPL, ROM and RADIO.
These ROMs are avaiable from your mobile provider's website or via a link in the ROM Section.
Click to expand...
Click to collapse
won't flash the spl over usb whilst hspl is installed.
H4z3 said:
Sounds great!
So i just run the original .exe file from my PC when my HTC HD2 is in bootloader screen in USB-mode, correct?
I have alreade flashed with original rom from PC when my phone was online. But then the HSPL did not go away even though my original rom was installed.
Click to expand...
Click to collapse
use the hspl.exe program to remove hspl just like you used it to apply it. just choose a stock spl instead of the hspl.
example, regular hd2, wants to go back to o2 stock everything.
run hspl2, choose 1.66.0000
run the o2 1.72.exe rom over usb.
all done.
if the rom doesn't flash its not the correct stock rom.
samsamuel said:
use the hspl.exe program to remove hspl just like you used it to apply it. just choose a stock spl instead of the hspl.
example, regular hd2, wants to go back to o2 stock everything.
run hspl2, choose 1.66.0000
run the o2 1.72.exe rom over usb.
all done.
if the rom doesn't flash its not the correct stock rom.
Click to expand...
Click to collapse
At first i used HSPL 3 to install 2.08.0000 HSPL.
But if i run that file again i only have the choice 2.08.0000.
I downloaded a previous version of HSPL, and there i could choose SPL 1.42.0000 wich was my original SPL version before the flash.
Is this a correct way to do this?
I am asking again because even though i now am at the original ROM and Original SPL version the Radio and Protokoll-version differs from the versions when i bought the telephone.
radio and protocol doesn't matter. yes you've done it right. so long as its a stock rom and the spl ends 0000 then it's fine.
Ok thanks!
Then everything is ok now and i am very happy for that, so thanks for all answers!
I can also add that i took my original SD-card (2GB) and put the LEOIMG.nbh on it.
The bootsequence then started ok when holding down volumebutton and power on.
But the result was exactly the same as it was when flashing to stock SPL with HSPL2 utility.
So the booting-problem was memorycard related.. So it seems that even some 8 gb memorymodules have problems.
Just thought you should know.
Related
Hi guys,
At the moment i have SSPL.
I want to install HSPL3 - 2.08
but i cant unstall the sspl.
when i try to install hspl, i get error, BAD SPL VERSION
to install my sspl i used the folowing steps :
1. Remove SD (and remove Application Data and Program Files folders from it using SD card reader)
2. Remove HSPL with HSPL2_RUN.exe (flash SPL 1.66.0000 with HSPL2_RUN.exe)
3. PowerOff the phone
4. Boot to bootloader (VolDown+PowerOn) and when it shows "USB" flash stock ROM by running matching RUU_Leo_S_HTC_XXX_3.14.XXX_Radio_15.42.50.11U_2.15 .50.14_LEO_S_Ship.exe (get yours HERE or for Orange UK/FR HERE)
5. Hard Reset (when phone starts booting after step 4, remove the battery, insert it back press VolUp+VolDown and still holding both press PowerOn and follow the instructions)
6. Boot to homescreen.
7. Run SSPL_RUU.exe with Artemis v40 RUU_Signed_0409.nbh in the same folder - YOU HAVE TO BE ON HOME SCREEN, NOT BOOTLOADER (this took me 3 tries until succeded - yes - nerve wrecking, but works). If it doesn't work (hangs on black screen for more than 2min or stays at 0%) remove the battery and try again. If still doesn't work - try solutions in NOTE below.
8. Hard reset (instructions in step 5)
9. when on homescreen - softreset.
10. Insert SD
Any help?
you dont have sspl, 'sspl - soft secondary program loader' is a one shot version of 'hspl - hard/hacked secondary program loader'.
You have 'spl - secondary program loader' - stock spl.
If you followed those steps you now have spl 3.03 and so hspl will not work. You must downgrade your phone to an earlier rom/spl version. 1.66 for example. USB will be fine so long as its your correct stock rom, , any version except 3.14.
samsamuel said:
you dont have sspl, 'sspl - soft secondary program loader' is a one shot version of 'hspl - hard/hacked secondary program loader'.
You have 'spl - secondary program loader' - stock spl.
If you followed those steps you now have spl 3.03 and so hspl will not work. You must downgrade your phone to an earlier rom/spl version. 1.66 for example. USB will be fine so long as its your correct stock rom, , any version except 3.14.
Click to expand...
Click to collapse
how can i downgrade?
its not working
as i said, get your stock rom, any version, but it must be correct for your phone, and flash it usb is fine. that's it.
AAh ok thanks it worked
I flashed original 1.66 ROM
No w i was able to install HSPL
Thanks!!!
no worries.
Hmmmm, I have the 3.14 ROM with 3.03.000 SPL installed.
What I`m trying to do is Install NAND Android. But to do this I need HSPL 2.08.
Tried downloading one of the older stock roms (1.66) and then attemped to flash via SD and through the .exe file directly.
From the .exe file it boots to the tri color screen and then reaches the progress bar screen. However it sticks there and the errors out with a code : 294.
Through the SD method after the phone detects the .nbh file it comes back with a "28002 : Not allow" error message.
Have tried this with varoius types of Mem cards but no luck.
I then tried SSPL with 1.66 as the ROM and i got it to flash the ROM with no problems but the HSPL still sticks at 3.03. And thats expected since SSPL is like a one shot go at flashing a ROM different from your region.
Question : Since this isnt working, will a task 29 help in this case? From what I understand it formats the filesystem that holds the OS. By doing so, will I then be able to flash one of the older Roms so I can install HSPL 2.08?
Any help will be appreciated.
xcsi said:
Hmmmm, I have the 3.14 ROM with 3.03.000 SPL installed.
What I`m trying to do is Install NAND Android. But to do this I need HSPL 2.08.
Tried downloading one of the older stock roms (1.66) and then attemped to flash via SD and through the .exe file directly.
From the .exe file it boots to the tri color screen and then reaches the progress bar screen. However it sticks there and the errors out with a code : 294.
Through the SD method after the phone detects the .nbh file it comes back with a "28002 : Not allow" error message.
Have tried this with varoius types of Mem cards but no luck.
I then tried SSPL with 1.66 as the ROM and i got it to flash the ROM with no problems but the HSPL still sticks at 3.03. And thats expected since SSPL is like a one shot go at flashing a ROM different from your region.
Question : Since this isnt working, will a task 29 help in this case? From what I understand it formats the filesystem that holds the OS. By doing so, will I then be able to flash one of the older Roms so I can install HSPL 2.08?
Any help will be appreciated.
Click to expand...
Click to collapse
i had similar issues, i used task29 that contains blank .nbh. you must have hspl 2.08 first to run this then install any custom ROM through PC or your branded ROM through SD card it should work or install Android then. i hope this helps.
here you go
http://forum.xda-developers.com/atta...0&d=1268260144
xcsi said:
Hmmmm, I have the 3.14 ROM with 3.03.000 SPL installed.
What I`m trying to do is Install NAND Android. But to do this I need HSPL 2.08.
Tried downloading one of the older stock roms (1.66) and then attemped to flash via SD and through the .exe file directly.
From the .exe file it boots to the tri color screen and then reaches the progress bar screen. However it sticks there and the errors out with a code : 294.
Through the SD method after the phone detects the .nbh file it comes back with a "28002 : Not allow" error message.
Have tried this with varoius types of Mem cards but no luck.
I then tried SSPL with 1.66 as the ROM and i got it to flash the ROM with no problems but the HSPL still sticks at 3.03. And thats expected since SSPL is like a one shot go at flashing a ROM different from your region.
Question : Since this isnt working, will a task 29 help in this case? From what I understand it formats the filesystem that holds the OS. By doing so, will I then be able to flash one of the older Roms so I can install HSPL 2.08?
Any help will be appreciated.
Click to expand...
Click to collapse
Is your phone branded (T-Mobile, Vodafone, O2, Orange, etc) and to what country?
If you are using a T-Mobile USA HD2, then you may try and flash the 2.08 TMOUS ROM.
Hey,
I want to do the exact same thing and I am locked on Orange? Is it possible to downgrade?
lhayati said:
Hey,
I want to do the exact same thing and I am locked on Orange? Is it possible to downgrade?
Click to expand...
Click to collapse
If you can find the previous stock ROM than yes. But it's a hard one to find (Orange UK)
Problem with spl3.03
Hello all. I trying today upgrade my htc leo to 3.14 rom but right now my htc is locked and I cant downgrade to any version . I trying to use all countries software for downgrade but allways I have information "NOT ALLOW"
My S/N is HT04YNW00034
Please help me.
dalisman said:
Hello all. I trying today upgrade my htc leo to 3.14 rom but right now my htc is locked and I cant downgrade to any version . I trying to use all countries software for downgrade but allways I have information "NOT ALLOWED"
My S/N is HT04YNW00034
Please help me.
Click to expand...
Click to collapse
Mate, do you want to upgrade or downgrade? You're statement is confusing
what do you mean "locked"?
As long as you flash the CORRECT STOCK ROM, you can upgrade or downgrade.
What you have to do first is find the CORRECT STOCK ROM".
you can't try all countries version, it is dangerous.
Go to htc website and select the country where your hd2 come from, and download the stock rom using your SN.
If you can't find the CORRECT STOCK ROM, the only alternative is using gold card method.
Good luck
I want to downgrade to version 1.66 but I cant beause always when I try to downgrade (using sdcard) I see information "not allow" . lock = Software update failed . please try again.
what is this gold card ?
dalisman said:
I want to downgrade to version 1.66 but I cant beause always when I try to downgrade (using sdcard) I see information "not allow" . lock = Software update failed . please try again.
what is this gold card ?
Click to expand...
Click to collapse
I think you haven't found th CORRECT STOCK ROM, that is why "not allow"
Gold card is a method to enable you to flash stock rom from other country (it is useful in a situation where you can't find the CORRECT STOCK ROM.
There is a thread for gold card, just using search button to find it out
Good luck
I allready check I think all countries because Im not sure from which country is my phone. and always on htc website I see information software is not for this S/N
dalisman said:
I allready check I think all countries because Im not sure from which country is my phone. and always on htc website I see information software is not for this S/N
Click to expand...
Click to collapse
Is it branded phone (telstra, Tmobile, orange, etc)? if yes, you should go to their website instead of htc website.
However, if you still fails, then the only alternative is using gold card method.
I never experience for this though I read it many times, so I would suggest you to search the forum. There is a thread title [GOLD CARD], just use search button.
Good luck
hello
I read about gold card and I understand everything, but my problem is :
my htc is detected by system but not detected by active sync
and I cant make gold card
dalisman said:
hello
I read about gold card and I understand everything, but my problem is :
my htc is detected by system but not detected by active sync
and I cant make gold card
Click to expand...
Click to collapse
I would suggest you to post this at the gold card thread, mate
Maybe there's someone can answer that.
Good luck
Hi all
Apologies if this has been covered before but I cannot find anything thus far. I upgraded my HTC HD2 (Vodafone branded) from 1.72 to 3.1.4. As the device was branded I had to use HSPL (version 3) as Vodafone had no specific version, at that time, and thus used the generic HTC version as it was all that was available at that time. This seemed fine until I hit the, what I now know to be the memory issue, with this combination. At this point after trying a number of custom ROM's, I am using a Dutty Custom ROM (V12, COM2). I decided today, as I just discovered that Vodafone now have their own specific 3.1.4 ROM update available I would flash the 3.1.4 ROM, which I was able to download legitimately from the HTC web site, using my serial number.
I first flashed the stock ROM in the vain hope that the Vodafone had fixed the memory issue. They haven't and thus I decided to remove HSPL. I did this from the installation program and chose the 0000 option which removes HSPL. I then rather stupidly decided to run a task 29, which of course, failed at 0% and just hung totally. It did not time out after 10 minutes, at which point I had no option but to remove the battery and data cable. Fortunately the phone booted up and ran normally. I thus decided to re-flash with the legitimate Vodafone 3.1.4 ROM. as the memory issue still persisted. It failed at 0% just as with the task 29. I now cannot flash ANY Rom unless I install HSPL. I have only tried version 3 thus far.
Any ideas how I can get my phone loaded up with my genuine 3.1.4 Vodafone branded ROM without HSPL and thus avoid the memory issue and load genuine ROMS and updates please? For now I am back to using the Dutty V12, COM2 ROM. Any ideas most gratefully recieved and apologies if this has been covered before.
Many thanks in advance.
Regards,
Paul Lemonidis.
Try flashing to HSPL 2 not 3, and read this thread
http://forum.xda-developers.com/showthread.php?t=609477
Russ
Flash your vodafone stock ROM over SD.
And to be able to install custom ROM, use SSPL_RUU
phone into bootloader
connect usb
run hspl2
choose 1.66.0000
when phone restarts immediately re enter bootloader
run the voda 3.14 rom flash over usb
Thanks
I flashed from an SD Card and all was well. I can now reflash the same version, which I could not before, without HSPL. Thus for the moment I no longer need HSPL. Thus my warranty is valid again and I have a stable phone with the latest correct vendor ROM. I may try a custom ROM again at some point in the future if I experience problems but at least I can say I gave it a fair chance.
As a sideline, Swype works beautifully with this ROM.
Once again many thanks in advance.
Regards,
Paul Lemonidis.
samsamuel said:
phone into bootloader
connect usb
run hspl2
choose 1.66.0000
when phone restarts immediately re enter bootloader
run the voda 3.14 rom flash over usb
Click to expand...
Click to collapse
hi
i am facing the similar issue, cannot revert back to branded ROm it does not boot any further than HTC logo, will the goldcard can do this,,, aslo my branded ROM is 1.72.82124, and reason i want to put back on is that my phone memory after installing custom rom is always less than 12mb then go below 1 mb in few hours..
tried hspl, sspl etc nothing works..
netvpn7 said:
hi
i am facing the similar issue, cannot revert back to branded ROm it does not boot any further than HTC logo, will the goldcard can do this,,, aslo my branded ROM is 1.72.82124, and reason i want to put back on is that my phone memory after installing custom rom is always less than 12mb then go below 1 mb in few hours..
tried hspl, sspl etc nothing works..
Click to expand...
Click to collapse
Take the 1.72 ROM and use the flash from the SD Card method. This will get you back your memory.
The reason for the memory problems is a combination of 3.14 ROM and HSPL.
My HD2 needs to go in for repair so I need to remove HSPL and flash a stock WinMo ROM ready for monday when it is getting collected.
I have followed the instructions here - http://forum.xda-developers.com/showthread.php?t=623402 but the screen does not go grey, there is a very quick flash then it returns to the multicoloured screen and pressing the power button does nothing
Would someone be kind enough to enlighten me here as I have to sort this before Monday.
Cheers in advance
Bry.
Bryski said:
but the screen does not go grey, there is a very quick flash then it returns to the multicoloured screen and pressing the power button does nothing
Click to expand...
Click to collapse
the quick flash is the bootloader looking for a valid file, and usually means one of a few things..
1 - the file isn't correctly named leoimg.nbh
2 - you simply renamed the htc_wwe_blahblah_.exe to leoimg.nbh instead of extracting ruu_signed.nbh and renaming THAT.
3 - you are using an sd card bigger than 4gb (not always the case, but most times bigger cards fail)
4 - the card is formatted FAT16 instead of FAT32
5 - hspl isn't installed after all and the ROM is not a match for the phones ROM/region lock. (what does the spl line say in bootloader?)
try those, see if it resolves it.
fix
go to http://forum.xda-developers.com/showthread.php?t=611433 and on the 4th post there is a zip at the bottom download unzip and run and just choose the non hspl
what hspl are you running?
Ok tried again and the bootloader screen looks like this
thats the right on but the last line about the touch is different i have 50 instead of 40
Any reason why it would be different?
Wanna make sure its dont right, dont want em sending it back and telling me I have hacked it
That's only a valid spl if you have a tmous,,,, if you have a regular hd2 then any spl starting 2 is wrong. Only tmous roms use 2.x spls.
Its a UK O2 phone mate, what have I done wrong then?
Bryski said:
Its a UK O2 phone mate, what have I done wrong then?
Click to expand...
Click to collapse
Well without scanning back through the thread, I'm guessing you had 2.08.hspl installed and ran hspl2 or 4, which will have defaulted to the opposite, namely 2.08.0000,
Or,you SD flashed a tmous stock rom, which didn't initially fail because hspl was installed, but then failed to continue to flash after the spl had changed because hspl was no longer there.
Fix - run hspl2 (hspl2 is the most usefull for us reg Leo users) and choose a matching spl to the rom version installed ...
Rom ....... spl
1.43 ....... 1.42.0000
1.66 ....... 1.66.0000
3.14 ....... 3.03.0000 -- you would need to use Hspl4 for this.
If the phone is buggered and wont boot, then it doesn't really matter which you choose, so long as it's one of those three.
(And in fact it probably wouldn't matter even if the rom and spl don't match,, they're only really interested in the spl, just nice to be cautious,would be a pain to have it sent back on a technicality)
Phone boots but I cant do anything with it due to the screen freeze which is why its going back to HTC.
Ok now it tells me I dont have SPL 1.42 on my phone and it refuses to flash a stock ROM :/
Guess I am screwed, new phone time
Bryski said:
Ok now it tells me I dont have SPL 1.42 on my phone and it refuses to flash a stock ROM :/
Guess I am screwed, new phone time
Click to expand...
Click to collapse
You're using the wrong hspl.exe, its v1 that requires 1.42 to work,,,try again.
Ok I think I got it
I should flash the latest ROM again aswell really as they asked me to do that when I rang em yesterday
All sorted and upgraded to the latest ROM ready to go back to HTC.
Cheers mate saved me a lot of heartache
Welcome...
while on this topic, im using Leo_RADIO_2.15.50.14** via HSPL
now i wish to return to my stock (which i am pretty sure is this :
RUU_Leo_HTC_Asia_WWE_1.48.707.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship.exe
(i copied down these details when i got my phone on the first day)
do i need to roll down to Radio 2.05.51.05_2 ?
i cant seem to get this ROM installed, whether its 1.42 SPL or 2.08 HSPL
i removed HSPL, and definitely not a TMOUS hd2 but cant install the stock rom
I currently have a MIUI android ROM installed but want to go back to WinMo 6.5 (stock). Now when i try to flash the ROM like i did before, its says on my PC USB Init failed, connection problem. The bootloader screen does say usb. Also when I try to flash trough the MAGLDR flash modus there is USB standing but i cant flash. I've also tried flashing the stock ROM from my SD card as an NBH file but it wont work.. Also repartitioning and all the stuff dont work because they all have te connection problem. I have tried multiple USB cables. Anyone know a solution??
you say that the SD flash doesn't work, can you elaborate a bit more?
explain everything you did, what ROM did you try, if you can give me the whole step by step you tried to SD card flash, including and file name changes etc
SD flash is usually the last resort and if you tried it with a genuine original Stock ROM it should work, albeit it will change the RADIO, SPL and ROM at the same time...
Hello,
I intend to downgrade my hd2 Europe version, from Android with Magldr, to stock Rom,
because of some bootloops i encounter after trying install wp7, so i want to start from scratch and try flashing wp7 or Android again!
I have HSPL 2.08 and i want to flash a Greek Stock Rom
(RUU_Leo_S_HTC_ELL_3.14.482.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship)
OR
(HTC HD2-RUU_Leo_HTC_ELL_1.66.482.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship_2).
My radio is 2.15.50.14.
So far i have made some research and i understand that:
1st. i must flash a stock Rom from SD.
2nd. The hspl will be replaced with stock SPL. Do i need to flash HSPL 3.03, as 3.14 ROMs on HTC HD2 Eu require SPL 3.03.0000 or HSPL 3.03, before flashing stock Rom from SD? What about 1.66 Rom?
The stock SPL version depends from the Rom which i would choose, or will be the same?
after that I just need to run HSPL4, install HSPL2.08 and continue with Magldr as i have done in the past?
Is there something I should be extremely careful so as not I have a fatal problem?
Thanks in advance everyone who will help a confused man!!!
(i don't wanted to start a new thread, so i posted here because of the title)
cmour said:
Hello,
I intend to downgrade my hd2 Europe version, from Android with Magldr, to stock Rom,
because of some bootloops i encounter after trying install wp7, so i want to start from scratch and try flashing wp7 or Android again!
I have HSPL 2.08 and i want to flash a Greek Stock Rom
(RUU_Leo_S_HTC_ELL_3.14.482.2_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship)
OR
(HTC HD2-RUU_Leo_HTC_ELL_1.66.482.1_Radio_Signed_15.30.50.07U_2.06.51.07_Ship_2).
My radio is 2.15.50.14.
So far i have made some research and i understand that:
1st. i must flash a stock Rom from SD.
2nd. The hspl will be replaced with stock SPL. Do i need to flash HSPL 3.03, as 3.14 ROMs on HTC HD2 Eu require SPL 3.03.0000 or HSPL 3.03, before flashing stock Rom from SD? What about 1.66 Rom?
The stock SPL version depends from the Rom which i would choose, or will be the same?
after that I just need to run HSPL4, install HSPL2.08 and continue with Magldr as i have done in the past?
Is there something I should be extremely careful so as not I have a fatal problem?
Thanks in advance everyone who will help a confused man!!!
(i don't wanted to start a new thread, so i posted here because of the title)
Click to expand...
Click to collapse
just follow the guide on the relevant ROM that your interested in
but if your playing with WP then use HSPL 2.08
if your flashing a stock ROM via SD as you pointed out it will replace the SLP with the one that comes with that ROM, so it doesn't matter what you do, then you can use HSPL4 to install the required version for the ROM that you want to use. You can use HSPL 4 to revert back to a stock SPL as well, but if you have any doubt at all then just re flash a original stock ROM, you cant go wrong at all then
Well, if i try to flash anything from my pc it says connection error. When I use flasher modus the HD2 freezes and i need to pull out the battery. I also tried flashing the stock ROM from my SD card but that also doesnt work. I use MAGLDR 1.13 and HSPL 2.08 i think. The current ROM is MyMIUI V11.
i managed to install the stock rom but now i cannot install magldr. When i start the installation the hd2 shows bootloader, then goes into the installation screen but after 1 second it flashes back to bootloader.. any help?
are you putting the phone in to the tri coloured bootloader with the word "serial" at the bottom? plug in to a USB port and the word changes to "USB" then install MAGLDR?
just so im clear what you have tried
i have install NexusHD2-ICS-CM9-HWA_V2.7 and worked perfect and i wanna to get back to win6.5 mobile and get it back my phone is htc hd2 512 ROM ( noooooooooot t-mobile ) i download the official ROM from htc.com install it or there is some things to do ????? plz help me fast :good:
No, you just install it.
option 1 (assuming you downloaded the 3.14 rom)
enter bootloader
flash rom from usb
reboot
enter bootloader
run hspl4
choose 3.03.hspl
reboot
done
option 2
extract ruu_signed.nbh from inside the yourdownloadedrom.exe
rename it to leoimg.nbh
copy it to root of your sd card (sd card 4gb or smaller, 2gb is preffered)
enter bootloader, it should start to flash automatically.
done
---------- Post added at 03:01 PM ---------- Previous post was at 03:00 PM ----------
Spaqin said:
No, you just install it.
Click to expand...
Click to collapse
assuming he doesnt want to remove hspl, that is, if he did 'just install it' and sent it back to htc, they wouldn't honour any warranty since hspl would still be there.
Also, he's just had android installed, so chances are the spl is 2.08.hspl, , , if he installed a 3.14 rom and didnt change teh spl, it wouldn't work, since 3.14 roms dont work on any spl except 3.03.xxxx (for regular hd2, , tmous seems to be able to handle 3.14 roms on non 3.03 spls)
ty aallllllll
HI Guys, I am also looking to install the standard rom back onto my phone as I want to make a claim under my insurance (o2)
The only problem I have is my touch screen has stopped responding (after I spilt petrol on the phone), is it possable to get the phone back to factory rom and radio without the screen working?
Thanks
Gary T
see the link 'Various radios, stock roms and tools HERE' in my sig, the o2 3.14 rom is in there.
either
..
open that exe file with a zip program (change teh extension from .exe to .zip will also work) inside get ruu_signed.nbh, rename it to leoimg.nbh and put on your sd card, reboot into bootloader and it will flash, , thats it.
or
...
into bootloader, connect usb, , when serial changes to usb on teh screen, run that .exe file. when its finished, go back into bootloader, connect usb, and run hspl4, and select 3.03.0000, done.
Hello. I'll use the thread to ask a simple question. I bought HD2 and it currently has Android ICS. I don't want to brick my phone in day 1 so to flash it back to WM6.5 I have to follow this guide, right ? http://www.youtube.com/watch?v=X--T--kvE24
The only thing that worries me is that I have spl-2.08.hspl not the 1.42 stated in the video, is that a problem ? I will use dutty's rom kitchen. Thanks.
EmZvr said:
Hello. I'll use the thread to ask a simple question. I bought HD2 and it currently has Android ICS. I don't want to brick my phone in day 1 so to flash it back to WM6.5 I have to follow this guide, right ? http://www.youtube.com/watch?v=X--T--kvE24
The only thing that worries me is that I have spl-2.08.hspl not the 1.42 stated in the video, is that a problem ? I will use dutty's rom kitchen. Thanks.
Click to expand...
Click to collapse
if you flashed over USB, then hspl isn't replaced, which is why it is still on 2.08,hspl.
Its perfectly fine, assuming you arent wanting to send it for warranty. if you do want to go back to 1.42 then use HSPL2.exe and set 1.42.0000