HTC P3400 is struck at start up screen.
It shows only >>
ONBL 1.07.000
SPL 1.0.7.00
OS 1.7.000
S/N starts with HT808FW and procured from India
It does not show the radio version..
Tried hard reset but does not go to reset mode..
Then tried flashing with RUU_Gene_hTC_Asia_India_1.17.720 shipped ROM but after 2% gets Invalid Vendor..
Even tried the gene unbricker by Orefkov (Matty Method), but no success..
Phone goes to bootloader mode by pressing Camara + Power On..
Need help >> Supporter come to rescue...
can u describe how/why the current situation occurred
Phone was getting restarted and then arrived at this condition...
has not been tapmered with any software...
it will be better to go to a service center instead
it seems to be hardware issue
Related
hi guys..
i hav a gene 100 or a p3400..
it went dead two days back as i was listening to music..i charged it up again but it just didnt start.. When i press the power button, the green light lights up and nothing else happens...
PLLLLSSSSS help......
gene
the gene doesnt even repond to the resets mentioned in the forum..
pls help me with any software or smthing..
plsss...
dead GENE- TRY THIS
We can hard reset the device just by pressing and holding both the " -" keys right above the answer and end keys and pressing the power button . It will run the ghost image and recover the device ...
note :
1) make sure your battery is more than 50 % charged .
2)you must do a power cycle in your device ( take out the battery , then press and hold the power button ) before you do a hard reset ...
My device is back to normal...
video is here
there you go http://www.youtube.com/watch?v=R53104JTgNI
Tried it once...
hi bryan..
thnkx for ya reply but i'v already done that but got no responce..
Can i fix it by flashing or smthin??.. i'm new to these things ...
Can you explain to me ... to what extend the device is screwd.....
Another P3400i bricked
I tried olipro spl on my p3400i and the screen went black.
later on i managed to get it to bootloader mode showing Olipro spl but unable to flash any rom everytime i have same error 300 'get newer update utility '
i tried mtty,htcflasher,hard reset without powering on but nothing works.
phone is stuck at bootloader screen .
help please
its isnt startin up
hi bryan..
Once i put he batery and switch the device on,the green led lightsup and staysthere until i remove the battery..( all this tym the device screen is black..)
the red led lights up when i connect it to my pc..
What are my options??..
shahabaz said:
hi bryan..
Once i put he batery and switch the device on,the green led lightsup and staysthere until i remove the battery..( all this tym the device screen is black..)
the red led lights up when i connect it to my pc..
What are my options??..
Click to expand...
Click to collapse
Your battery is finished. I started getting that when my charger got messed up and starts taking power out of the battery instead of putting it in. Take out the battery,put it back in, then plug it to your PC and leave it there for a while.
mailforkrishna said:
I tried olipro spl on my p3400i and the screen went black.
later on i managed to get it to bootloader mode showing Olipro spl but unable to flash any rom everytime i have same error 300 'get newer update utility '
i tried mtty,htcflasher,hard reset without powering on but nothing works.
phone is stuck at bootloader screen .
help please
Click to expand...
Click to collapse
If your s\n starts with 814 - there is no solution now
Daemon_Hell said:
If your s\n starts with 814 - there is no solution now
Click to expand...
Click to collapse
no it is HT816FW01645 is there any hope
i have the same
my ht807
is it repaired ?
the same problem for me.
s/n start with HT829
any solution to recover?
to all p3400i guys
you can do nothing.... i am also having the same problem..... only solution take it to a service centre and tell them to hard flash and reinstall the windows..... my p3400i is in the service centre right now... we cant flash p3400i .... i dont know why???
go4thoman said:
you can do nothing.... i am also having the same problem..... only solution take it to a service centre and tell them to hard flash and reinstall the windows..... my p3400i is in the service centre right now... we cant flash p3400i .... i dont know why???
Click to expand...
Click to collapse
I too had taken my P3400i to service center but they did no solution Motherboard has be changed ??
and it cost 75%of a new P3400i
mailforkrishna said:
I too had taken my P3400i to service center but they did no solution Motherboard has be changed ??
and it cost 75%of a new P3400i
Click to expand...
Click to collapse
try to hard reset it and get the boot loader and flash with it the stock rom for p3400i i will give the link soon. my friend did it for me. then i send it to bangloure service centre, now waiting for their reply. They said that if we try to flash it our warranty will be void..... dont know what to do now.......
GENE 100 dead (stuck on bootloader)
Same with me
After running orefcove gene hspl my gene is dead and It goes up to tricolor bootloader and hangs. Cannot do any rom upgrades (ERROR- invalid upgrade tool)
Now SPL is 1.10.Olip
Orefcove HSPL
http://forum.xda-developers.com/showpost.php?p=1847381&postcount=37
(please dont use this and you will end up with dead gene like mines)
I have Gene 100
S/N HT817
basha said:
Same with me
After running orefcove gene hspl my gene is dead and It goes up to tricolor bootloader and hangs. Cannot do any rom upgrades (ERROR- invalid upgrade tool)
Now SPL is 1.10.Olip
Orefcove HSPL
http://forum.xda-developers.com/showpost.php?p=1847381&postcount=37
(please dont use this and you will end up with dead gene like mines)
I have Gene 100
S/N HT817
Click to expand...
Click to collapse
If you have not completed 14 days after buying the device, just take it to HTC service center sying that your device is not booting. At least in my case, those guys couldn't figure out what is the cause (see how efficient they are ) and I got a replacement !
basha said:
Same with me
After running orefcove gene hspl my gene is dead and It goes up to tricolor bootloader and hangs. Cannot do any rom upgrades (ERROR- invalid upgrade tool)
Now SPL is 1.10.Olip
Orefcove HSPL
http://forum.xda-developers.com/showpost.php?p=1847381&postcount=37
(please dont use this and you will end up with dead gene like mines)
I have Gene 100
S/N HT817
Click to expand...
Click to collapse
I used the exact same HSPL ... and was able to upgrade to WM 6.1 ROM by cyan..
mGforCe said:
I used the exact same HSPL ... and was able to upgrade to WM 6.1 ROM by cyan..
Click to expand...
Click to collapse
What is your serial, is it P3400i
basha said:
What is your serial, is it P3400i
Click to expand...
Click to collapse
Nope... its P3400 which came with WM 5.
My HTC is under the S/N : H7XXXXX, but accidentally use the H8XXXX to flash it. Now my HTC unable to start except press the "Camera" key and "Power" key to up my HTC, and it only shows the 3-color screen on it.
When I tried to use the original ROM "P3400 - 24 March 2007" to do the flash, but the upgrading fails and shows "Invalid Vendor ID".
Please help me on this. Thanks
Please advise on a solutions
I have the same serial number on my htc but mine i hardspl it with stock rom wm6.1. Tried the reflashing it and still don't wanna work.also tried the mmty program but it not work on my device
Time to visit the Docs. Sorry!
try changing the spl first... check the old posts for old gene..... man you have to do some reading b4 flashing...which spl its showing now is it oref or olpiro.. is it still detecting the Usb... showing at btm lft corner?
the one and only solution is to send the device to HTC service centre...
ther is also 2nd option,,,, if u flash ur device with stock WM5 version 1.7.455.2 WWE
but this ROM is nowhere available..
i hv faced exact same problem , which u r facing now....thn i tried almost every method...but nothing worked....thn finally i send device to HTC service center.....
next day they returned my device fully working again....
so........this is the only way for u now....!!!
bst of luck..
I have HT7 Phone it bricks during upgrading the SPL because it had WM5 and I went to install WM6
I can boot the Phone in Recovery Mode ( Holding the Camera Button and Boot ). Three Color Screen and I can communicate with the phone through the MTTY but during installing the Update it says ERROR 300
is there anyway to get the phone alive again ?
Thanks for your Help
** I have Kaiser and it's not mine , it was belong to my friend and I damaged his phone
PS : Phone is out of warranty and there is no service center here , also I can't use the JTAG Method
jafer mainly error 300 comes in when you are using wrong rom update utility... atleast in my case...after running spl pgm from phone and mtty program make sure you run the rom update utility inside the spl folder before running the rom update utility inside the rom folder... hope this helps.. and make sure that the rom is for old gene...
which spl its nowing at the tricolor screen now... oref or olipro?
which spl its showing at the tricolor screen now... oref or olipro?
ONBL 1.10.0000
SPL 1.07.oref
Thank you
Could you please explain more , where to get those files
I got Unbricker from here
http://forum.xda-developers.com/showpost.php?p=2784291&postcount=66
Thank you again
Question : when TriColor Launched can I re-flash the original firmware ? i don't know what to do now
Please look at the stickey, krazy has made quite a good tutorial about flashing etc and has all the tools hyperlinked. LoL
Hi Thanks but please don't refer me to reads topics , because i've already read all of them
The Phone is HT7 , during the upgrade it bricks , I used the " Orefkov " but it seems it only works for new Phones
Anyway by no I can Boot the Phone in Tri Color Mode but when i try to upgrade a rom it says ERORR 300
is there any way to BOOT the Phone through the SD Card ? I already had the same issue with another phone , I boot the phone with SDCard and it became alive again !!
But I don't know the Instructions for this GENO Crappy Phone
try removing the SD card and update the ROM. BTW as far as i know oref Is for new Gene. post a query on the right thread and ankit or krazy or any proficient member will definitely help you out. or you may pm basha for help.
I ran hspl.exe. It's didn't restart but went off. I press soft reset now only bootloader is showing with ONBL 1.10.0000 and SPL 1.10.Olip. there is also RUU at the top right corner. What can I do now to flash another rom or get back my gene?
your_suraj said:
I ran hspl.exe. It's didn't restart but went off. I press soft reset now only bootloader is showing with ONBL 1.10.0000 and SPL 1.10.Olip. there is also RUU at the top right corner. What can I do now to flash another rom or get back my gene?
Click to expand...
Click to collapse
First try to remove the battery and then put it back in and try to switch it on see if it boots into the windows...if not then follow the step given below...
Download any custom rom for OLD gene and run the rom update utility (RUU) it will be back to normal...
Note : Most importantly don't panic ...even if the phone is taking its usual time to boot up it may seem longer cos we are worried....have patience...
hay man
tell us the serial number of your device to tell you exactly what to do
is it (ht8xxx) or (ht7xxx) ?
it is very important
and for god's sake guys read the sticky threads first.
do not do anything before getting answers from other members.
Thanks guys, but I solve it already but I am not able to download any rom for my gene.
Can somebody give me another mirror apart from rapidshare and megaupload............. and which ROM is good, like with cube for my gene HTC 3400?
your_suraj said:
I ran hspl.exe. It's didn't restart but went off. I press soft reset now only bootloader is showing with ONBL 1.10.0000 and SPL 1.10.Olip. there is also RUU at the top right corner. What can I do now to flash another rom or get back my gene?
Click to expand...
Click to collapse
Its normal thing that ur device got off after hspl.exe
it seems like u hv new gene....so now u should use Oref unbricker...
u just followed step 1....
so u should move on to step 2
which is unbricking gene by oref method
http://forum.xda-developers.com/showthread.php?t=472169
read this bro n follow instructions...
Thank you once again but I have solved my problem already. Now all I need is a new rom for my old gene.
Could anyone give me alternative mirror for any rom? Rapidshare and megaupload is not working for me.
Help - Gene stuck at boot loader after upgrading ROM 6.5
ONBL 1.07.0000
SPL 1.07.olip
GSM 02.79.90
OS 1.7.0.0
This happened when i upgraded the ROM from WM 6.1 to 6.5
Kindly help me how to restore my phone
same here
same happened to my Gene. I tried upgrading ROM to 6.5. after restart, it get struck on bootloader screen. it is not even detected by activsync
i flashed my new gene
now i am at the tri colour screen
its showing ONBL 1.17.0000
SPL 1.10.Olip
when i give a click on Rom update Utility
its giving me ERROR [300] : INVALID UPDATE TOOL
please help me wat to do
its almost been a month, that my phone is not working
Follow krazy's thread, starting with the gene unbricker step.
you have only done 50% hspl, if you are sure your Gene is New
u can also use @fusioncoast
hi
just a suggestion Viabhav has provided a tool to chek if ur phone is old or new use it and he has also provided the HSPL tool also try it it will tell u wether ur phone is new or old
goodluck
fusioncoast said:
i flashed my new gene
now i am at the tri colour screen
its showing ONBL 1.17.0000
SPL 1.10.Olip
when i give a click on Rom update Utility
its giving me ERROR [300] : INVALID UPDATE TOOL
please help me wat to do
its almost been a month, that my phone is not working
Click to expand...
Click to collapse
now the phone does not reboot after updating Rom
i was successfull in updating the ROm, but after clicking finish....the phone should retart
but it does not restart
tried manual restarting.....
tried hard reset
nothing works
my phone is not booting up after updating the ROM
try this @fusioncoast
hi
try this
1.off the phone & take the battery out
2. press the power button on the phone for a few secs after removing battery
3.put battery back in the phone
4. press& hold camera button & then power button this will give u tricolor
use USB and Flash a new ROM
if ur sure ur SPL is .olip then Flash with old gene ROM or look in this same site besfen has also provided the orginal wm6 ROM u can also try the same
good luck
fusioncoast said:
i was successfull in updating the ROm, but after clicking finish....the phone should retart
but it does not restart
tried manual restarting.....
tried hard reset
nothing works
my phone is not booting up after updating the ROM
Click to expand...
Click to collapse