I have a herm300 ipl-1.04 spl-1.40 olipro, and when I try to open appers the bootlother screen with 4 colours red,green,blue and white, and I don't cnow what to do.. pleas help me,please
Format a 2Gb or less sd card FAT32 then copy he .nbh file for Hard SPL V7 onto it. Rename to hermimg.nbh and insert it into the Hermes. Restart the Hermes.
This should put a new Hard SPL onto your Hermes. It should now read IPL - 1.04, SPL 2.10 olipro.
Now do the same things again but use a new rom instead of Hard SPL and don't worry about formatting again.
This should get you back up and running but as you have installed a new ROM you will loose all contacts/messages and apps installed...
As you can't get to today screen this is unavoidable....
Cheers...
thanks a lot , now I mus to reboot the battery an I will try ... thanks
joke9 said:
thanks a lot , now I mus to reboot the battery an I will try ... thanks
Click to expand...
Click to collapse
when I try to upgrate the pda from the pc , the bildversion don't appers the bildversion from the pda , what schold I do (( ,I have try with the card and no respons, the same thing
what schoul I do with my herm?,, it will not upgrating ,the bildversion don't appears When I try to upgrate and the program it's working erything it's going, the upgrating is finisch but the spl version dosen't upgreated it's the same ......... please hellp :
Sorry, should have said Restart the Hermes in bootloader - Hold power, OK button above flywheel and reset with styls. Hold all buttons in until the tri-colour screen (bootloader) appears...
Must've been tired...
Related
after update my hermes my phone dosent start windows after another upfate with a shipped rom the phone finish the update but stil dident start windows any suggest
ipl.1.01
spl 140 olipro
londere said:
after update my hermes my phone dosent start windows after another upfate with a shipped rom the phone finish the update but stil dident start windows any suggest
ipl.1.01
spl 140 olipro
Click to expand...
Click to collapse
You might need to reflash it. Hold the two soft keys and then push the reset button. it will ask to hard reset. If the phone fails to come on after the hard reset, then hold the left 'ok' key and the power button, and then push the reset under the phone- this will take you to a tricolor screen where you can then re-flash the phone. try reflashing with official rom's, before using any other roms.
yes i do but it still in boot any sugest ipl 1.01 spl 1.40 olipro if any know how to update ipl with hard spl or how to remove hard spl it will be aprecible
My suggestion would be to try using sd to reflash the rom and see if that orks. format sd card making sure its fat 32 then put .nbh file in root directory. rename to herimg.nbh then insert into phone. go to bootloader and it should start the flash straight away. if this works make sure you upgrade spl to olipro 2.10 hard spl so its easier if there are problems. you can possibly upgrade spl this way too (get nbh file and rename hermimg.nbh). I tried this on my herme 100 and it seemed to work. it will flash the spl BUT when it restarts it will go straight to bootloader and start flashing again. as soon as it restarts get the sd card out and put on the os you want to flash. insert card and as long as you've named it hermimg.nbh it should flash new os with spl olipro 2.10. Good luck flashing.
You should read the wiki first : http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
your phone can be unbricked using the information on wiki.
only enter to bootloader the ipl dosent start also i fla**** but it stil apear spl.140oli whei in flash it with hard spl 1.10 and when i flash it with spl 2.60 oli it send me a error i try to flash it with qtek-cingular-doppod roms and nothing any suggest
any fu**ing suggest?
also it avoid me to update spl im stuck on hard spl 1.40 and ipl 1.04 i try to flash hspl 260-210 but it refiuses to stay in 1.40 radio 1.27 patched the ipl works but it frezzes with the green led dosent apear nothing
my device still blocked in boot mode i dont know if it is briked the device had the following info
ipl 1.04
spl1.40 oli
radio maybe no
os no
any suggest
any sugest to save my hermes
follow the unbrick guide link that koorosh_bsboys posted
it cant be unlocked its stuck in spl 140 olipro
did you follow the unbrick guide that koorosh_bsboys posted?
just stop trying any unauthorised ideas. let me know if i can help u. i have a friend in o2 service centre here in india. he can get ur device working. he does it by help of a software and 3 cables . it takes about 2 hrs. just let me know if u want ur device to work again
stil zombie my device im getting crazy any ideas
londere said:
stil zombie my device im getting crazy any ideas
Click to expand...
Click to collapse
If you want people to help you, you have to help yourself first!
1st of all, have you gone to read the Wiki as suggested?
2nd what methods have you tried to unbrick your device?
If you can't answer these questions then we can not help you, you keep asking for suggestions but you do not even reply to other's questions!
Here's a good place to start helping yourself if you haven't already http://forum.xda-developers.com/showpost.php?p=1465974&postcount=1
Hi,
Please help me, as its very urgent. I have been upgrading to various ROM's every now and then. Recently I did a blunder, as While upgrading with One of the ROM (Black Majik) i selected SPL 2.10 instead of Force SSPL and while upgrading USB Connection get lost.
Now I am only getting the Splash Screen showing HTC, when i Hard Reset my phone I do not get IPL and SPL version displayed and it takes my to the Splash Screen again.
Please help me in finding a way i can recover my phone.
Thanks in Advance
Regards
Try a hard reset...
If that doesn't work and you have Hard SPL on your phone upgrade using the sd card method.
As for your IPL and SPL, what do you see when you go to bootloader? That shows your IPL & SPL. To get to bootloader press power, OK button next to flywheel and soft reset with stylus. Hold all three buttons until you get to tri-colour screen. That will tell you what IPL & Spl you have.
Cheers...
Thanx for help. I could get my IPL and SPL info. But still i am not been able to get any rom installed on my device as it get stuck on that tri-color screen and rom up gradation wizards comes with different rom looks for activesync connection with the device. I am not been able to boot my device so that i can upgrade it to specific rom. Is there any way i can install a ROM without having active sync connection with the device...
Pl.. Pl.. Pl.. help. I would be greatfull to you
IF you have flashed Hard SPL on your phone you have a good Chance...
If you haven't and its under warranty you might be able to get them to fix for you.
Assuming you have Hard SPLed your phone, try the sd card method - format up to 2gb sd card fat32. copy the .nbh file from the rom upgrade to the sd card.Rename the .nbh file to "hermimg.nbh". Reset phone. As you keep going into bootloader you wont have to manually do that. It should recognize the os flash and prompt you to hit the power button to proceed...
PLEASE NOTE - THIS WILL ONLY WORK IF YOUR SPL IS 2.10 OLIPRO...
Hope you upgraded your SPL cos you will only have a paper weight otherwise..
Best of luck. Cheers...
hi,
I have One Herm 100 Imate Jasjam.It came to me for the repair,i searched and found the solution in the forum.The device has no IMEI and No Gsm and booting properly but no network.So i follow this thread "How to unbrick your bricked hermes" Link is http://wiki.xda-developers.com/index.php?pagename=Hermes_Unbrick
and found that the solution from the given Table after answering the all the questions,so the solution is (1.) Flash Hard-SPL (2.)Flash any radio in NBH format.Do both steps using SSPL+ActiveSync.
i could succesfully Flash the Hard-SPL.Now i put the Phone is bootlaoder mode i can see that the HERM100 IPL-1.04 and HERM100 SPL-2.10.Olipro.
But when i am performing the second step that is "Flash any radio in NBH format.Do both steps using SSPL+ActiveSync" (i downloaded the Hermes_Radio_1.50.00.00_108) from the support and trying to upgrade the radio but it always starts and stuck at updating 0% and not moving further and an error message popping up saying error 260 and 262.I read the read me and followed all the instructions but all the time i am getting the same error.
So please guide me what to do?
Waiting for replies from all the PDA Guru'S.
Regards,
Moderate.
If you had of read you might have found this is a problem with VERY low probability of you fixing it....
So saying, try the sd card method, You have Hard SPL on the phone, do this....
1. Format an sd card fat32 and copy RUU_signed.nbh on it. Rename to hermimg.nbh.
2. Insert sd card and put Hermes into bootloader - Hold down power, OK button above flywheel and then use stylus to reset... Hold all three in until you get to the tri-colour screen A.K.A bootloader.
3. It should recognise the herm flash file so follow the prompts...
If the Radio only rom doesn't work you can try a stock rom... Best if you try the carrier rom it was initially.
If that doesn't work, at least you have a nice PDA.....
Good Luck, you're gonna need it...
Cheers...
ultramag69 said:
If you had of read you might have found this is a problem with VERY low probability of you fixing it....
So saying, try the sd card method, You have Hard SPL on the phone, do this....
1. Format an sd card fat32 and copy RUU_signed.nbh on it. Rename to hermimg.nbh.
2. Insert sd card and put Hermes into bootloader - Hold down power, OK button above flywheel and then use stylus to reset... Hold all three in until you get to the tri-colour screen A.K.A bootloader.
3. It should recognise the herm flash file so follow the prompts...
If the Radio only rom doesn't work you can try a stock rom... Best if you try the carrier rom it was initially.
If that doesn't work, at least you have a nice PDA.....
Good Luck, you're gonna need it...
Cheers...
Click to expand...
Click to collapse
First of all thanks for the reply.
I am using Carrier NBH and following your instructions and now it is updating the image lets see,it has just started.i willl update here with results.
i Can see on screen the following details.
================================================
HERMIMG.nbh -
IPL - OK
BOOTLOADER - OK
SPLASH1 - OK
SPLASH2 - OK
EXTROM - OK
GSM -
OS -
Update in Progress...
================================================
Regards,
OOps it stopped at some percentage say between 10 to 15.And it didn't move further for more than 30 minutes.
I removed and trying to flash via pc but it is hanged at 14% now for a very long time.what could be the problem.Could this be hardware or i am making misake somewhere.
Dunno,,
regards,
moderate said:
OOps it stopped at some percentage say between 10 to 15.And it didn't move further for more than 30 minutes.
I removed and trying to flash via pc but it is hanged at 14% now for a very long time.what could be the problem.Could this be hardware or i am making misake somewhere.
Dunno,,
regards,
Click to expand...
Click to collapse
Congratulations! You now have a Hermes PDA
I have something like this now
I tried flashing CRC13 via USB
at about 92% it failed. It attempted to recover and failed again.
I used a 1gb lexar MicroSD, copied the CRC rom's RUU_Signed.nbh to the card as HERMIMG.nbh
reset holding Power and OK buttons.
It flashed 000680002 and went back to the tricolor screen
Herm100
IPL-1.04
Herm100
SPL-2.03
I'm trying the KITL method from http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
Any other suggestions?
If I let it attempt to boot normally, the CRC splash screen comes up, then brightens for a second, then goes blank. The charge indicator will respond to power, and the USB will make the PC "bu-bumb" but AS will not connect, explorer will not see it, and RUU_Wrapper will not detect it
Thank god... I DL'ed a factory OS, extracted it and ran the RUU_Wrapper and that did install
then installed CRC13 naked
All is well
Radimus, HARD SPL YOUR PHONE.... You were EXTREMELY lucky... If you are thinking about reflashing your phone you need Hard SPL ver 7 installed... It won't guarantee you won't brick your phone but will offer a safety net so you may be able to fix it.
Cheers...
for some reason the hardspl7 will not install via AS for me...
Is it OK to do it via sd card using SSPL-HERM.exe
Yep, thats actually my preferred method of flashing. Check out post 1160 on page 116 of this thread for instructions - http://forum.xda-developers.com/showthread.php?t=296722
You can also flash Os'es with the sd card method. Once you've Hard SPLed your Hermes you won't need to use sspl.exe but make sure your battery is more than 50%.
I personally wouldn't flash the radio rom from the pc as there are too many things that can go wrong. SD card all the way...
Cheers...
done.
sspl.exe rules
HERM100
IPL-1.04
HERM100
SPL-2.10.Olipro
Click to expand...
Click to collapse
i just bought it and thinked it`s a rom problem....after reading many hours and writing wizard love rom molski aku 3.3...nothing changed ..tried tu update ipl spl but nothing ...hard reset do not work << FAT FORMAT..FORMAT FAILED >>i can do soft reset i can even flash it but nothing starts...if you know a solution please help me... the device ony shows ipl 2.16.0001
spl 3.08
i was a nokia fan no windows mobile devices...so please tutorial for stupids
Use the attached file... copy YOUR nk.nbf file in the folder you extracted
and then run ROMUpdateUtility.exe
1. Extract RUU_NoID.zip
2. Copy the nk.nbf from the wizard love rom
3. Paste in the RUU_NoID folder
4. Run ROMUpdateUtility.exe
5. Follw the instruction of the programm
6. be happy if it works
please heeeeeeeellllppppp
done that with wizard love and witn no ui utility...but nothing changed....i can write rom....it say`s congratulatios on rom installer...but pda still stuck on the same tricolor screen with the same ipl/spl :|
:S update ipl/spl to 3.08.0001 then do the update ? use the german tmobile aku... 3.3 http://www.t-mobile.de/downloads/t-mobile/ruu_vario_aku3.3_3822_382120_026911_tmo_de_ger_ship.zip
wait a second and i`ll tell if it works
i uploaded t-mobile rom all ok but stiilllllll nothing changed :| wtffff
If you have an SD Card in your phone, take it out. That's it 99% of the time.
Myrddin Wyllt said:
If you have an SD Card in your phone, take it out. That's it 99% of the time.
Click to expand...
Click to collapse
no sd card nothing ...HOW CAN I REPAIR THIS STUbBORN THING ???
Sounds like memory has bad sectors.
You may be holding a brick. Sorry.
hello friends,
i bought a jasjam (hermes) from ebay but the device it not works. the os isn't in it. I tried to hard reset, soft reset and i try to update MDF, SPL etc. MDF is 1.01 SPF is 1.00. I cant install any os to my device. It's always giving to me an Error about connection problems. i try to use mtty and i see no bad blocks. whats the problem? and how do i use my device?
thank you.
My Device is:
HERM100
IPL-1.00
HERM100 MFG
SPL-1.01
no body knows?
congrats, you bought a brick...
If you are REALLY lucky it may have Hard SPL on it. Try this...
SD card Must be 2Gb or less.
1 Format SD card FAT32. Copy .nbh file of ROM to it.
2 Rename .nbh file hermimg.nbh then put in Jasjam. Reboot to bootloader.
3 If its going to work and you have done EVERYTHING right, follow onscreen instructions.
thank you so much for your reply ultramag69 but i tryi this way. i see 1 or 2 sec. Loading... on my screen and than after its turning back to tri color screen / bootloader screen. another way?