i have charmer pm200 which is in dutch,i want to change it to english language.i need hardspl in order to flash the wwe rom
There is no HardSPL for Charmer.
ChrBeck said:
There is no HardSPL for Charmer.
Click to expand...
Click to collapse
I Have Charmer PM200 (G4) and i install Prophet HardSPL aka (SPL 2.G4.4PDA) ... It Work for my Charmer.
Are you realy sure it works? It can't cause ROM layout is different for Charmer so no Charmer ROMs will boot.
If I'm wrong I'd like to see some screenshots of it.
Cause I can't believe that.
ChrBeck said:
Are you realy sure it works? It can't cause ROM layout is different for Charmer so no Charmer ROMs will boot.
If I'm wrong I'd like to see some screenshots of it.
Cause I can't believe that.
Click to expand...
Click to collapse
ok n.p. Sorry for bad pictures, i don't have photo camera, created with samsung U700 camera. And LCD not full color, broken flex. I revive it with JTAG, 1 week ago. and loock inside for spl, may be i'm wrong, but it booting and working for my Charmer,
OK very interesting. By the way. I've got a Charmer here where the IPL died. (It still boots but bootloader mode is dead). So where are the JTag Pins on Charmer board and which JTag kit have you used? Would be cool to know that.
If I'm able to get that IPL ok again I may the the HardSPL too.
ChrBeck said:
OK very interesting. By the way. I've got a Charmer here where the IPL died. (It still boots but bootloader mode is dead). So where are the JTag Pins on Charmer board and which JTag kit have you used? Would be cool to know that.
If I'm able to get that IPL ok again I may the the HardSPL too.
Click to expand...
Click to collapse
ok.np. http://pda2u.ru/topic348.html.... Needed H-JTAG Software 0.92, NoICE. Repair Step same as wizard, becose wizard and charmer PM200 have Omap850 proccessor. if your Charmer have M-System DOC G4 use wizard sspl-s_wizard.nb, if G3 you need typho5, and official full firmware for extract with typho5.
Related
Hi,
I have Qtek 9100 with IPL 1.01 and SPL 2.20.0001. When I switch on divice, it displeyed color screen and nothing more. I flash it whit many ROM's but IPL/SPL always is the same and did't work normal. How can I resolve the problem. Thanks!
Only with a JTAG device. It's a special device that can access the chips without the need for the phone to be working. But nobody knows which are the JTAG pins so no luck here.
The IPL 1.xx is meant for the G3 DOC chip Wizards and G4 all have IPL/SPL starting at 2.xx.xxxxx. Since IPL is the firt bootloader with information and addresses for SPL and since they don't match you'll never get out of that situation...
Thanks for reply. I have JTAC device and will try to find jtag pinouts for Wizard G4.
havy said:
Hi,
I have Qtek 9100 with IPL 1.01 and SPL 2.20.0001. When I switch on divice, it displeyed color screen and nothing more. I flash it whit many ROM's but IPL/SPL always is the same and did't work normal. How can I resolve the problem. Thanks!
Click to expand...
Click to collapse
Try..
(1) put the phone in bootloader mode
(2) flash it with cingular 1.x radio (search for it)
you should get a normal device in the end
best of luck!
dont know how
kdskamal said:
Try..
(1) put the phone in bootloader mode
(2) flash it with cingular 1.x radio (search for it)
you should get a normal device in the end
best of luck!
Click to expand...
Click to collapse
(1) OK
(2) DONT KNOW HOW!!
Please help, i never did this. how do i flash the phone if my comp does not recognise it (i can only enter the bootloader screen).
You should
1) Flash only IPL/SPL from g4 (f.e. 2.26.0001) to get your SPL/IPL the same with italian RUU 2.5.2
2) Flash ROM without IPL/SPL italian RUU 2.5.2
yesterday we bringed such device to live) try
how do you compare that with Atom
Hi,
I have got O2 Arom.
does anyone know whether my device is equivelent to G3 or G4?? or its completely diff technology that cannot be compared!!!
I know O2 Atom is by Quanta and it uses CPLD (Complex programmble Logic Design!! I hope i remember this right).
this can't be compared at all, totally different technology. there is a whole separate section for the atom. just go to the forum root page and look for the atom.
Hello,
I will start with my story: I have a qtek S200 and i have make a mistake i think? a friend off my set that i cane use every rom for your phone. So i have putt this a Vincent rom on it. (that's the only thing i know)
Now i want a new rom but, every Rom for a Prophet that i tray on my S200 stops by the Red/Green/Blue screen.
Can some wane help me to get a working Rom for me or a fix for this problem.
Thanks
(And sorry for the bad English)
i think it is in this topic right? (http://forum.xda-developers.com/showthread.php?t=353547)
the problem. You haven't HARDSPL your Device.
Now, go to bootloader mode and flash PDAVIETTemp ,which can be found here.
PDAVIET TEMP
and HARDSPL your Device.
once you HARDSPL your device. SPL information should be 2.G4.4PDA for PPC G4 or 2.G3.4PDA for PPC G3.
Read WIKI. What is SPL. And how to go to bootloader mode.
Thanks
Hello varanusvincent,
So if i'm right my device was not ready jet for WM6? En after your Prophet_Temp i cane load every Rom 6 in it? I'm right?
Tanks
Edit: I have tray your Temp but i won't work. is there another way to hardSPL my device?
For the second time i have load te Rom in the image stay still at 74% cane i break the operation? And how do i get te boot screan back after a abord?
Smattie said:
Hello,
I will start with my story: I have a qtek S200 and i have make a mistake i think? a friend off my set that i cane use every rom for your phone. So i have putt this a Vincent rom on it. (that's the only thing i know)
Now i want a new rom but, every Rom for a Prophet that i tray on my S200 stops by the Red/Green/Blue screen.
Can some wane help me to get a working Rom for me or a fix for this problem.
Thanks
(And sorry for the bad English)
i think it is in this topic right? (http://forum.xda-developers.com/showthread.php?t=353547)
Click to expand...
Click to collapse
You may try
Just a question: I have still Red/Green/Blue?
My IPL 2.21.0001
SPL 2.20.0001
Still i cane not update?
Smattie said:
Just a question: I have still Red/Green/Blue?
My IPL 2.21.0001
SPL 2.20.0001
Still i cane not update?
Click to expand...
Click to collapse
1. yes, can still update,
2. FORCE BOOLOADER MANUALLY, (very important )
3. Flash NVID for Prophet
4. after restart and activesync,
5. use my Lazy_tool to flash any rom you like....
Enjoy....
Sorry, i'm busy for 8 hours with this ..... phone and it's very hard for me to dot it wright.
So how do i get in "FORCE BOOLOADER MANUALLY" and what do you mean by "Flash NVID for Prophet"
(i'm sorry for all the questions but if read all the Wiki's and guide's but it still not working)
I hope you cane explaine it to me
Smattie said:
Sorry, i'm busy for 8 hours with this ..... phone and it's very hard for me to dot it wright.
So how do i get in "FORCE BOOLOADER MANUALLY" and what do you mean by "Flash NVID for Prophet"
(i'm sorry for all the questions but if read all the Wiki's and guide's but it still not working)
I hope you cane explaine it to me
Click to expand...
Click to collapse
Have you read wiki for prophet?
Here are how to enter bootloadermode
PDA Viet Temp is just to make you back to WM5 no vendor.
To hardspl your device. Read here.
You can HARDSPL your device. Or use lazytool from youzi. Posted from dioxda2.
Lazytool is using softspl.
varanusvincent said:
Have you read wiki for prophet?
Here are how to enter bootloadermode
PDA Viet Temp is just to make you back to WM5 no vendor.
To hardspl your device. Read here.
You can HARDSPL your device. Or use lazytool from youzi. Posted from dioxda2.
Lazytool is using softspl.
Click to expand...
Click to collapse
Hey smattie,
from the wiki, there is a sentence missing after "To enter bootloader, you need to hold the comm manager button and soft reset."
that is " then release the stylus and keep pressing the comm. button until you see the bootloader screen"
Dear VaranusVincent,
Lazy_Tool is a modified version from Youzii's Chinese version, I had that named "LAZY" because I am ~~~~~~~
Hello varanusvincent and dioxda2,
Very tanks for the good explenations and tips. i want to tank you guys for that.
Just another question the SPL is now 2.G4.4PDA cane i run every rom now ore must i do it with a tool?
Smattie said:
Hello varanusvincent and dioxda2,
Very tanks for the good explenations and tips. i want to tank you guys for that.
Just another question the SPL is now 2.G4.4PDA cane i run every rom now ore must i do it with a tool?
Click to expand...
Click to collapse
Don't worry, both way can do.
1. Flash with the tool included in your favorite rom package.
2. or change the nk.nbf in the Lazy_Tool will do ,too.
enjoy~~~
imate jamin boot loader problem
please help me my imate jamin after upgrade shows red green and blue colour iam not able to enter boot loader by pressing com manager and reset button please help
josepgreg said:
please help me my imate jamin after upgrade shows red green and blue colour iam not able to enter boot loader by pressing com manager and reset button please help
Click to expand...
Click to collapse
READ WORD BY WORD~~~~~
http://wiki.xda-developers.com/index.php?pagename=prophet_bootloader
HELP
Hai My Phone Shows 3 Colours And Ipl &spl Nos What Sould We Do
josepgreg said:
Hai My Phone Shows 3 Colours And Ipl &spl Nos What Sould We Do
Click to expand...
Click to collapse
He josep,
Have you this whole topic? You must load the bootloader your self. And what this have you trayed?
I have an Imate jamin.. and i installed wm6.1.. everything was goin good..but lately i installed and other rom on it and now it doesnt go forward... it is stuck on the start screen... i need help!!!
Hey,
First try an hard reset, this can be done with pushing the _commmenager-button+Camera-button+stylus-reset(on bottom of ur device)_ at the same time, just release the stylus-reset some earlyer then the other 2 buttons.
if thats not working:
Try to charge your mobile with your original charger,
Then go to your bootloader, put in the USB Cable.
goto the site of your brand of phone... imate / qtek or whatelse...
download official WM5 ROM.
try to flash it again.
Also flash your radio rom to 02.19.21
I like 02.19.21, i think its the best radio-rom for prophet i ever used.
but that can be because i have Vodafone, dont know if its also the same with your provider...
but i should say, give it an try!
here you can download all Radio-Roms.
First of all, when u start flashing again to WM5/6 (doesn't matter what rom) always use HARD-SPL!
And i can advice you an good rom(although for me in case)
The rom made by VaranusVincent
ROM Prophet Blue Manilla 2d
Have fun!!
whoops doublepost...
Simply stuck and wandering...
Hi there
I am a noob in this area. I am reading the forum for the last days and trying to upgrade my i-mate jamin G3 but i always get stuck...
I started this thread as it involves more than one thread I read, namely
- Windows Mobile 6 Directory For Dummies
- New WM6 Upgrade Guide
- HardSPL guide and files
- Prophet Tools Light: Just the flash! & Prophet Tools: Simplify Flashing--V2.8.3 now up!
- Current upgrade guide for the most ROMs
- LAZYTOOL For all nk.nbf FLASHING + 3 color bootup SOLUTION + (PLEASE READ.........)
- WM 6.5 build 21501 Titanium [ Fixed ] & Fixed CommManager, and other ROMs I tryed...
- ...
so here it goes:
#1# I tryed to run HardSPL an I got an error message like this:
'One or more CON code pages invalid for your given keyboard'
so i guess i didn't work...
#2# then I tryed with ProphetTools and after doing the HardSPL it asks (in jamin) to run JumpSPL I click on yes and then I get white screen (in jamin) I click the flash rom and then I get either:
- error 260 or 274 - connection - this sometimes is worked around and got to 208
or/then
- error 208 - file open (and I did put the nk.nbf rom file in ...\Tools (as said on PTL) and also tryed in ...\Utils\Flash)
#3# While in white screen (achieved with PTL) I also tryed ROM 21501 (with its own RUU) and I get 3 colour screen after supposedly successful upgrade...
#4# also tryed lazyTool but got the same 3 colour screen
#5# With the no vendor NVID_RUU (got from lazy tool thread) I got it back to WM5 and working, pitfully i forgot to dump my original rom so now i am stuck in WM5 in English (i at least had it in Portuguese - my native L)...
I found this comment from dioxda2 in another thread...
Quote:
dioxda2 said:
Try to flash the NVID from Here http://forum.xda-developers.com/showthread.php?t=353547,
if your Prophet works fine after that, you may flash any rom you like ,
...try to read my thread and....Good luck and
Click to expand...
Click to collapse
... actually my prophet (jamin) works fine after I flashed the NVID, the problem is that I can't put it to work with any other ROM...
So any of senior experts plz advice
hopefully i am missing some supidly simple solution
#6# Meanwhile if someone knows were do download a original PTG ROM for prophet I would appreciate.
MYG
Jamin G3 unlocked
IPL 2.13
SPL 2.20
NVID
Last edited by MYGene; Today at 06:20 PM.. Reason: confused with dioxda2 comment...
my prophet is G4 so slightly different i would ask you to post detail for the second boot screen
here is mine
IPL 2.10.001
SPL 2.G4.4PDA
GSM 02.19.21
wapvirus said:
my prophet is G4 so slightly different i would ask you to post detail for the second boot screen
Click to expand...
Click to collapse
My SPL only shows:
IPL 2.13
SPL 2.20
im a total noob here too but i never encountered the same prob as you have.. i see SPL 2.20 right... so if you want to flash a ROM from here its required that you do HardSPL. i have a G3 device too. you might want to try this... i will try to help as much as i can...
make sure your USB cable/cradle is working perfectly and try to attached it at the back of your PC CPU...
and btw are you using XP or VISTA? coz i use XP...
just RUN HardSPL and let it do its thing... when its done check your SPL again..
marekPLPH said:
im a total noob here too but i never encountered the same prob as you have.. i see SPL 2.20 right... so if you want to flash a ROM from here its required that you do HardSPL. i have a G3 device too. you might want to try this... i will try to help as much as i can...
make sure your USB cable/cradle is working perfectly and try to attached it at the back of your PC CPU...
and btw are you using XP or VISTA? coz i use XP...
just RUN HardSPL and let it do its thing... when its done check your SPL again..
Click to expand...
Click to collapse
I just got another USB cable borrowed and tried the HardSPL you uploaded and it Worked
Actually It gave me the same error message about 'One or more CON code pages invalid for your given keyboard' but this time I didn't got the 3colour screen at the end, instead it restarted normally with SPL 2.G3
I am just waiting battery charge reaches 50% to try flashing it
Many thanks
(I assume either i got a corrupted HardSPL file either a bad USB cable...)
MYGene said:
I just got another USB cable borrowed and tried the HardSPL you uploaded and it Worked
Actually It gave me the same error message about 'One or more CON code pages invalid for your given keyboard' but this time I didn't got the 3colour screen at the end, instead it restarted normally with SPL 2.G3
I am just waiting battery charge reaches 50% to try flashing it
Many thanks
(I assume either i got a corrupted HardSPL file either a bad USB cable...)
Click to expand...
Click to collapse
Good to hear this...
Happy Flashing!!!
MYGene said:
I just got another USB cable borrowed and tried the HardSPL you uploaded and it Worked
Actually It gave me the same error message about 'One or more CON code pages invalid for your given keyboard' but this time I didn't got the 3colour screen at the end, instead it restarted normally with SPL 2.G3
I am just waiting battery charge reaches 50% to try flashing it
Many thanks
(I assume either i got a corrupted HardSPL file either a bad USB cable...)
Click to expand...
Click to collapse
That,s great news and happy flashing
Hello
after upgrading i'm stucked in spalsh screen (the one with rom version and others...). can i skip this step? the device is lost?
do you have others questions?
Cheers
no one?
Hi.. did I broke the device?
Cheers
Hi!
Give us more info about your device.
IPL,SPL,installed ROM,etc
Did you try hard reset?
BR
Szig
Here you have the answer like given many times before:
If format fails it is hopeless.
If format goes well and works take the original Aku3 ROM and flash it. The device will work again.
Stuck in splashscreen
High to all
I have a problem with my Charmer - I was flashing it, when I didn't read any instructions and I failed it. Some month ago I came back to Charmer and I repaired it with the "Rescue Kit" and it worked some time. But now even if I flash it with any ROM, my PC write "Congratulation", Charmer turns on but stuck in the splash screen and It's all... when I go to bootloader, it goes and write the IPL and SPL, but when I do Hard reser, it writes "Formad failed", but It can be flash!!! With any ROMs... Please, help me, I like this phone...
punker1993 said:
High to all
I have a problem with my Charmer - I was flashing it, when I didn't read any instructions and I failed it. Some month ago I came back to Charmer and I repaired it with the "Rescue Kit" and it worked some time. But now even if I flash it with any ROM, my PC write "Congratulation", Charmer turns on but stuck in the splash screen and It's all... when I go to bootloader, it goes and write the IPL and SPL, but when I do Hard reser, it writes "Formad failed", but It can be flash!!! With any ROMs... Please, help me, I like this phone...
Click to expand...
Click to collapse
ChrBeck said:
Here you have the answer like given many times before:
If format fails it is hopeless.
If format goes well and works take the original Aku3 ROM and flash it. The device will work again.
Click to expand...
Click to collapse
Hi!
As you can see mostly it is hopeless.Rarely rehotting DOC chip can help and I read somewhere that sometimes flashing helped,but that was a desperated try with Prophet ROM or something like that.If I was you I could try to flash it with Goldcard (just from curiousity and nothing to lose),but if ChrBeck can't help then who?
BR
Scootie
OK first:
Yes that mith with the Prophet flashing is true. But for that we need a working Aku1 ROM to get the IPL down.
Then the Prophet thing works. That is what I found out.
The heating up thing is a mith. It helped only 1 time and is not the best you can do.
And Goldcard is the biggest SH*T I ever heared.
For devices without reachable OEMSPL something like a Goldcard doesn't exist. Goldcard just flashs with SuperCID and without Signature checking. It is like using a HardSPL and won't help.
That is all I know.
Get a good working AKU1 and I'll build you the solution (if my idea is realy right).
ChrBeck said:
OK first:
Yes that mith with the Prophet flashing is true. But for that we need a working Aku1 ROM to get the IPL down.
Then the Prophet thing works. That is what I found out.
The heating up thing is a mith. It helped only 1 time and is not the best you can do.
And Goldcard is the biggest SH*T I ever heared.
For devices without reachable OEMSPL something like a Goldcard doesn't exist. Goldcard just flashs with SuperCID and without Signature checking. It is like using a HardSPL and won't help.
That is all I know.
Get a good working AKU1 and I'll build you the solution (if my idea is realy right).
Click to expand...
Click to collapse
Hi!
Thanks for the answer.
Just a few things:
I'm in searching for an AKU1 ROM.I had it on my computer years ago,but it lost when my HDD damaged.If I find it,I will upload it for you.
The heating up:in this case probably it doesn't help.When we have a device that can't be flashed properly,we try this and it helps more often than you think.Not only with PDAs,but with phones too.
Goldcard SH¤T:
I know what is Goldcard about.
The reason I mentioned it,it helped me 3-4 times when the device (not only Charmer,other devices too) stuck on bootloader or splash screen after flashing.I didn't have too much time in the workshop,so I tried this and worked.
I don't want to argue with you,I know you are an expert in this,I just tried to help with my experiencies.
BR
Scootie
P.S.:I found it on the xda-developers ftp server: RUU_Charmer_1120223_11202110_11220_T-MobileUK_Ship.rar
ftp://xda:[email protected]_1120223_11202110_11220_T-MobileUK_Ship.rar
OK nice that you found the ROM. Maybe we'll have a new test package for the fix of format failed error soon then.
And yes you are right sometimes Goldcard helps if you have forgotten to flash HardSPL or it is damaged then it may help but you need to have acces to OEMSPL and we don't have it.
So hope I can do something soon.
Hi!
I have a question:
I have a Charmer with IPL,SPL 3.08.Unfortunately it is CID locked,so I can flash it with official v3 ROMs only.Is there any solution to downgrade it?Or with JTAG only?
Thanks in advance!
BR
Scootie
The NoID RUU will be able to downgrade it.
Hi!
I tried that,but:
1.flashing is successful,but nothing has changed,I get the old OS after upgrade
2.I tried the v1 ROM I found.The IPL has been changed to 1.12,but the SPL remained 3.08.The OS has been changed in this case,so it worked flawlessly.
The CID unlocking methods didn't work (obvious,SPL was 3.08).
After that I tried to upgrade it,but it was a torture.I got errors and errors,but after an hour finally I could upgrade it successfully.
So,if you have an idea,I have a device to test it.
BR
Scootie
The IPL is down means it worked. After that you can flash a Prophet ROM.
What ROM of Prophet?
High, I was today flashing my Charmer with all original ROM I mean and the flashing process behaves OK, after flashing, it writes "Congratulation" and all the things like OS, Radio, IPL... are change to the definite ROM. But it's all. It will stuck in the splash screen... I have read in this thread something about Prophet ROM. What is it?
The prohpet ROM is an official Prophet AKU 2 flashable after downgrade.
System is as follows:
Fist flash the Charmer AKU1
Then flash a Prophet AKU2
Then flash Charmer Aku3.
You need to do all these steps with the NOID RUU.
That should fix the HardReset failing.
I'm working to get a tool running that does the whole thing automatically.
THX
Oh ****, Thanx 4 quickly answer...And I'm waiting :-D
Ok, so now I'm having
IPL 1.12
SPL 1.12.0000
GSM 01.12.20
OS 1.12.2.23
And I'm waiting 4 your instructions...
How have you gotten the SPL down?
Normally, with flashing... It can be flashed with every ROM...
OK. Cause normally SPL stays up. I never saw a full downgrade.