Related
hi everyone,
i have a huge problem. my rom flash for my i-mate (qtek 2020, mdaII, XDAII) hung during flashing (from 1.66 to 1.72 official i-mate rom) during the ce upgrade step 2. now my i-mate just hangs at the blue i-mate screen and i cant connect to it through pc anymore, get error 101. is there any way to get a good rom on it again (can i connect to the ppc by another way, other software or sd-card0 so it will work again, or does it have to be epaired at at a rapaircenter?
thnx, sorry for the bad english
See the pm i send you.
I have the same problem ...
plz tell me how u solve it
Best regards
plz help, i-mate dead after failed flash, error 101
Hi,
If all that happened was it hung during upgrade you can put the device into bootloader, power+d-pad+softreset button, and attempt upgrade again, but if OS you were upgrading to is corrupt causing the hang a new rom might be the way to go, www.buzzdev.net has everything i needed, or clubimate.com
I have same problem. My q-tec100 is reseting so I can' connect it to pc for flashing again. Please tel me what is bootloader and what is d-pad button so thad i can stop it from reset and connecting for flash
hi friends i have the same prob. somebody plz help me too
How to upgrade from WM5 TO WM6
To upgrade your prophet to WM6 I recommend that you first of all downgrade to the NVID version of WM5 AKU2.2 and get the latest Active Sync:
1. Download the NVID(no vendor) AKU2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe YOU CAN USE Step1 of PdaMobiz or PDAViet Temp INSTEAD OF NVID(no vendor) AKU2.2 ROM...
2. After it has been downloaded get the latest Active Sync from Microsoft.com
3. Install active sync, you might need to reboot
4. When your computer has rebooted, run the file from step No 1 . Follow the steps, remember that it can take some time and seem to stuck at 80% and higher, but just wait.
5. When you have done this, your pda will reboot. After it comes with the welcome to windows mobile screen,"Tap Here To Begin",JUST LEAVE IT. In fact don't touch your device before the next steps are finished.
6. Now download one of the WM6 versions( http://forum.xda-developers.com/showpost.php?p=1279985&postcount=1 )
7. Now find a file named Upgrade.bat,and run it.(you don't have to run Step1 of PdaMobiz or PDAViet Temp,as you have already downgraded to AKU2.2)
8. Wait until the upgrade finishes(usually takes 12-15minutes)..WAIT WAIT WAIT
9. A message will be displayed in the dos box,and it will say that the upgrade is finished etc....etc...,now you HAVE to HARD RESET,to finish the upgrade and enjoy you new WM6!
How to downgrade from WM6 TO WM5
The downgrade process from WM6 to WM5 is pretty simple. All you have to do is to downgrade to WM5 NVID and after that upgrade to the WM5 you want:
1. Download the NVID(no vendor) AKU 2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exeYOU CAN USE Step1 of PdaMobiz or PDAViet Temp INSTEAD OF NVID(no vendor) AKU2.2 ROM...
2. After it has been downloaded get the latest Active Sync from Microsoft.com.. Simply search for "Active Sync"
3. Install active sync, you might need to reboot
4. When your PC is ready run the NVID file you downloaded in step1 and follow the guide, remember that it can take some time and seem to stuck at 80% and higher, but just wait
5. When its done downgrading to the NVID WM5 rom, you prophet will reset and you can upgrade to the version of WM5 you want.
NOTICE
If you use a different AKU 2.2 ROM(like PDAViet Temp),you may have two EXEs in the folder you extracted.Be careful and use the one that is made for your device:
FILENAME G3.EXE
is for G3 devices:IPL x.xx.0000, SPL x.xx.000.0 (this is shown when you reset)
FILENAME G4.EXE
is for G4 devices:IPL x.xx.0001, SPL x.xx.000.1 (this is shown when you reset)
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
How to switch or upgrade/downgrade between WM6 versions(for example PDAViet->Trueneytral)
1. First you have to downgrade to WM5 AKU2.2 using the WM6->WM5 guide(some say that you don't have to do that,but i believe that it's better to downgrade first rather than making a simple overwrite)
2. Now follow STEP 5 of the WM5->WM6 guide
Device doesn't connect to PC after flash
If your device doesn't connect to your PC after flash,just enter bootloader(press camera button+while pressing soft reset and hold,until a tri-color screen shows up),and flash the NoVendor WM5 Rom: http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe .Then repeat the whole process...
----------------------------------------------------------
KEEP IN MIND:
UPGRADING CAN BE DANGEROUS,YOU ARE RESPONSIBLE FOR THE DAMAGE TO YOUR PHONE
DO NOT RESTORE BACKUPS FROM ANY ROM OTHER THAN THE ONE IT WAS CREATED ON
THERE IS NO "BEST WM6 ROM",THE BEST IS THE ONE THAT WORKS BEST FOR YOU
(part of the guide is taken from Da9L's guide,in the WM6 Rom Collection)
I will edit/update this post soon and clean it up, ask questions in another thread, and by god please read the wiki first, 90% of the questions asked are answered in the wiki....
WM6 Upgrade Guide...reply
great info sir! thanks so much! downloading...i'll be happy to send feedbacks on this WM6 ROM! thanks again!
Thanx a lot tonydeli7 , very very good guide and a lot of ppl really needed it
Great
Thanks to you all. I have Qtek S200 and trobuled with WM6 it wonderfull guide for me thank you very much.
I need to downgrade to WM5, 'couse I cannot boot anymore. After running the setup I get an error that the device cannot be found. I have connected the S200 with the boot loader running.
Edit: Now it works on an "old" WinXP machine.
Huge Problem!!
Ok guys I am having a huge problem. I tried to upgrade to WM6 but when running the RUU and changing the rom, it encountered an error saying the nbf file cannot be installed on my pda phone and now my phone is stuck(i think permanantly) on the bootloader screen.
No matter what I do to try to fix this, IE: restart device, power down by removing battery, try to run the RUU again, nothing helps. Its is really stuck and I really need this cell phone.
PLEASE HELP IF YOU CAN.
Dan.
dharvey4651 said:
Ok guys I am having a huge problem. I tried to upgrade to WM6 but when running the RUU and changing the rom, it encountered an error saying the nbf file cannot be installed on my pda phone and now my phone is stuck(i think permanantly) on the bootloader screen.
No matter what I do to try to fix this, IE: restart device, power down by removing battery, try to run the RUU again, nothing helps. Its is really stuck and I really need this cell phone.
PLEASE HELP IF YOU CAN.
Dan.
Click to expand...
Click to collapse
Put you pda on bootloader mod... and try any of this rom's i have managed http://forum.xda-developers.com/showthread.php?t=316062
Stay cool!
I followed the instructions carefully, and my phone (Qtek S200) seemed to boot with WM6.0
However, after aligning screen, it tried to initialize the phone with some extended roms, a procedure which failed, and I had to soft reset.
After reboot, it seems to work fine.
Is it?
EDIT: Another thing I noticed is that keyboard is in THAI !!! How can I make US the default? Olso, I have Resco keyboard GR edition. Will this work with WM6?
tonydeli7 said:
1. Download the NVID(no vendor) AKU2.2 rom for WM5 here :http://rapidshare.com/files/17208693/RUU_Prophet_220734_2207114_024721_NVID.exe
Click to expand...
Click to collapse
Is this G3 only, or both?
I'm asking, because in PDAviet's temp file there are two different rom updaters, but in the file linked above there is only one.
yoda_143 said:
Is this G3 only, or both?
I'm asking, because in PDAviet's temp file there are two different rom updaters, but in the file linked above there is only one.
Click to expand...
Click to collapse
i don't know mate.i believe you can use pdaviet's temp instead of aku2.2 nvid...
Another thing I noticed, is that it looses pairing with my bt handsfree...
I am making the pairing, and works fine. However, when at night I am shutting off my hf in order to save battery, the next morning the pairing is gone.
Any solution to this?
i hav a problem!i have sucessful boot wit wm6 and everythings fine but only i can't access to contacts,everytme i press it will automatic switch back to today screen...and there is no autoconfig???anyone help???i can't save my contacts...
dufchan said:
i hav a problem!i have sucessful boot wit wm6 and everythings fine but only i can't access to contacts,everytme i press it will automatic switch back to today screen...and there is no autoconfig???anyone help???i can't save my contacts...
Click to expand...
Click to collapse
You've forgot to do a hard reset after flashing, please read one of the flashing guides.
I-mate Jamin
hello evrybody
i just wanted to know if i can upgrate my WM5 to WM6 on my I-mate JAMin?
rondol1 said:
You've forgot to do a hard reset after flashing, please read one of the flashing guides.
Click to expand...
Click to collapse
thank u very much!!now my dopod working fine!!thanks a lot!!
thanx for the guide
help me please..
P4k1t0 said:
Put you pda on bootloader mod... and try any of this rom's i have managed http://forum.xda-developers.com/showthread.php?t=316062
Stay cool!
Click to expand...
Click to collapse
how to do that?
thx..
Choice of ROM
Hello guys, tanks for a so nice job !
I would like to have more information about the choice of ROM.
I don't want any special feature, just the row wm6.
no programs added, no tweaky today, no bugs, no battery problem, etc etc
which one would fit that the best ?
thanks
Thnx for this man, much appreciated!
Help please!
I have an T-Mobile Ameo (also known Athena X7500) and i tried the Olipro Unlocker, but the installation didnt finish, at 59% stopped. After that i turn off the device, then turn on, but my device still have a 4 colour screen,red, green, blue and white, it doesnt boot the Windows Mobile, just have the installation screen...
please help
Use olipro's tool again and then flash your final ROM
i tried it many times, but since than my Athena X7500 was dead, the Olipros unlocker doesnt work. The program said: "The Update Utility cannot connect your PDA phone"
In bootloader (coloured screen), does it say anything? if so what? when you try to flash a rom or use unlocker do you get a code? is your memory card out of the slot?
I took a photo my bootloader (coloured) screen:
http://kepfeltoltes.pirateclub.hu/pics/20090106317.jpg My device doesnt say anything.
When i used the unlocker, i didnt got any code. And my memory card was in the slot.
I also took a photo what the Olipro's said now, if i try to continous the flashing:
http://kepfeltoltes.pirateclub.hu/pics/20090106319.jpg
Have you tried flashing your carrier's original Rom?
i will try it, but i dont know where can i find my original rom...
and my second biggest trouble: in this mode, i cant charge my batteries. If i dont find an solution this problem soon, i think, my device will be a BIG trouble. Grrr, i hate olipros program...
Thanks a lot, my athena is live again, i flash my original rom!!!
But the Olipros Unlockert isnt working, the installation go to 100%, the program said that the flashing is succesfull, but my SPL is still 1.1, and i cant flash any roms..
I can understand why. Any ideas?
The other thread was closed, you shouldn't double post.
Read the links I mentioned.
as in olis first post
"Please note: you must have .net Framework 2.0 installed with the services packs, if you don't it then it probably won't run till you download it.
SPECIAL INFO ABOUT STEP 2: When you run this step, first your device will be flashed; this is NOT the end of Step 2, you must then configure your device and set it up fully so you can access the menus etc (there will be a prompt to ask you to do this after the flash anyway). then you will be able to continue. please make sure to read ALL dialogs fully"
leave out the sim and sd card.
Some others have reported better luck with the shipped WM6 rom if they had trouble unlocking.
I installed the NET Framework 2.0 SP2 in my device and i put out my sim and sd card. And when i flashing the Olipros Unlocker, it went to 100%, but my SPL is still 1.1
I dont understand.
VorosAdam said:
I installed the NET Framework 2.0 SP2 in my device and i put out my sim and sd card. And when i flashing the Olipros Unlocker, it went to 100%, but my SPL is still 1.1
I dont understand.
Click to expand...
Click to collapse
the net framework should be on your computer.
what OS is on your computer ?
May be better if you use winXP
did you install an oficial wm6 rom ?
Read the later pages in the unlocker thread
My computer also have the NET Framework 2.0 SP2. And when the flashing didn't work, i also installed the NET Framework 3.5 SP1, but, when i flashing a ROM in my decive, it also went to 100%, but the SPL is still 1.1.
I use a 32-bit Windows XP in my computer.
My T-Mobile Ameo (Athena) is a second hand device, it was used when i bought. But the first user said me, that the original OS was the Windows Mobile 5 in my Athena, but he update from Windows Mobile 5 to Windows Mobile 6.0. He said that he update with an official T-Mobile way.
Ok all good so far
Did you use the unlocker from this thread?
http://forum.xda-developers.com/showthread.php?t=315831
The other thought i had was that you should try a different computer and usb cable
oh, thank you so mutch, i tried an another computer, and it flashed the SPL from 1.1 to 1.2!
thanks again
my htc advantaage x7500
hello myfrnd please help me as my phone is dead after i used ur rom upgrade 3.5, i was already using michy cooked version of window mobile 6.1 im new in this field and during upgrade process after going 92% it just stuck and and showing 3 color screen it has a msg of IPL 1.2 OLIPRO pls help me i will donate u if u could solve my problem
thanks
sheizi said:
hello myfrnd please help me as my phone is dead after i used ur rom upgrade 3.5, i was already using michy cooked version of window mobile 6.1 im new in this field and during upgrade process after going 92% it just stuck and and showing 3 color screen it has a msg of IPL 1.2 OLIPRO pls help me i will donate u if u could solve my problem
thanks
Click to expand...
Click to collapse
I saw someone with the same problem as you here awhile back and he was able to fix it. So keep your post alive or read the sticky post under the Upgrade section. I believe that was where I read it.
dead X7500
Hey Im also a sufferer of a dead X7500......this all happened wen I was trying to flash my ROM which was using a SPL !.20 OLIPRO
wen I try to re flash the device , it starts a stops at 1% and follows an error msg !
plzzzzzzzzzzzz help me out to solve this prob !
regards!
VorosAdam said:
i will try it, but i dont know where can i find my original rom...
and my second biggest trouble: in this mode, i cant charge my batteries. If i dont find an solution this problem soon, i think, my device will be a BIG trouble. Grrr, i hate olipros program...
Click to expand...
Click to collapse
I have the same problem would be kind and tell me how you solved the problem.
[email protected]
Hello All
my work has 100 mda vario's
but they all had windows mobile 5.1 on it
so i say to my boss i can flash it to windows mobile 6 with htc touchflo
he liked it so he let me do it
but it goes wrong
the mda vario does nothing anymore
just a bootloader cames up with : red green,blue,white
saying :
ipl 2.21.0001
spl 2.21.001
my idea is to get a working rom on a mini sd card and flash it from the sd card
but how to let the sd card starts load and let it flash,
not one button works in the bootloader
i have tried a lot of tricks i also have one time get restore to factory defaults.
but wont work, it says format completed, so no error's
thats good i think
but i really need to fix it.
otherwise my boss wont be happy
also active sync wont work anymore , the pc wont see the phone all .exe updates ultilty gives me errors that they dont get response from the phone
that comes because it only stays in the bootloader and the bootloaders has left under a usb sign, there stood usb
can this be fixed?
any help plz
Regards
R.G
hi there... 2 bad is the boss phone!!!
hi there... 2 bad is the boss phone!!!
first of all, try a hard reset, then plug once again the phone to PC
dont worry, activesync wont recognize phone at all (is just usb connection)
tell me if hard reset worked, and ill keep in touch
i kpnw there is a tool that would help you to fix the phone.... first try the hard reset!
Good luck
I got the same problem, the hard reset works, but the problem is there yet.
Ich hab das gleiche Problem, der Hard reset funktioniert, das Problem besteht jedoch weiterhin
Hello All
Thanks for u responses i like that
okay hard reset works
but nothing has changed by that
hard reset is the question with restore to factory defaults?
and than i get a screen with format complete.
Regards
R.G
hello All
i fixed it
i know get a green screen with ipl,spl, os
but everything is terrible slow
really slow i mean when i press start it takes a minute to show up
why is this?
plz help
i fixed it with abort all processes in task manager and use wizard love rom.
this is the only possible way i think
regards
R.G
R.G
You know what you did,whats wrong with the phone,you flashed a wm6 rom to a CID locked device.A CID locked phone cannot be upgraded to wm6,you must have a CID unlocked device for upgrading to wm6.
Now,as its a G4 device,it cannot be CID unlocked,but,however,it can be upgraded to wm6 through either SoftSPL or HardSPL method.
Now first recover back to its default status by downloading official stock rom and flash it,after it starts to work normal,then follow the SoftSPL or HardSPL method,only then it'll upgrade.
Attached you find all you need to flash cooked ROMs on your Sedna.
This has been on my HDD for quite a long time. I nearly forgot I did this
The package includes:
sspl-1.02mfg-sedna.exe (copy it to your sedna and run it)
HardSPL-1.02-mfg-sedna.nbh (flash it after running the sspl)
CustomRUU.exe (use it to flash the HardSPL)
Once the HardSPL is installed on your device you can flash any ROM.
Have fun,
JockyW
PS: Moderators please make this a sticky. Thanks.
hurray for jocky2001.... finally we got hardSPL
so who else is cooking...? we need help and info and your experience Sedna chefs.
this forum has got to get big.. it is after all a nice big Toy..the sedna
so ill post my experiences and what i find out along the way.. so people can do it too
THANKS jockyw2001...
procedure...
to install hard spl you must do it this way...or at least i did and it worked for me
1. download the attached files
2. REMOVE SIM and SD CARDS !!
3. connect usb cable
4. copy sspl-xxxxxx.exe to your device and run it (usb cable must be connected!)
5. after a few seconds "USB" appears on the display
6. unplug and replug the usb cable
(OPTIONAL, better to skip it! step 7. Have a cigarette. If you dont smoke have a cup of tea)
8. you can now flash the hardspl-xxxxxx.nbh by running CustomRUU.exe. make sure hard spl and custom are in same folder
9. after installing the hardspl you can flash any rom
i did these exactly and it worked for me... when i go into bootloader it says SPL-1.02.HARD ... YIPeee!
to get to bootloader its in this forum somewhere..
thanks JOCKYW2001
i really (really) need a WM5 rom for this device, now we have this can one be ported ?? i REALLY need help with this
im no expert but id say so...just keep the radio from a sedna rom.. it has the drivers i think... and port only a wm5 OS.nb
let me know how u get on....
did u install hardSPL... i did and now i can load any rom so far
do you knowmuch bout this stuff...? do you know how to cook these ROMs .. which tools are you using..i have cooked roms before but with different phones and those tools are not fully working here..
and do you know if you can unlock the Extended ROM..?
let me know... good to have a bit of life here.. i went looking for the HARDSPL and finally got one off jockyw .. olipro would not answer my questions
no never have, all new to me, would be very greatfull if someone fancyied building one for me
as for installing hard SPL, thats later as the battery is flat at the moment.
yeah well id like one to do my work for me too... but im a realist..#
but i like to know how other people got on with theirs .. where they suceeded and failed so i can avoid pitfalls and get my jobs done right...
let me know if you know anything..and how you get on with WM5 ..
and how you hard spl goes... do the steps above and it will work
jockyw2001 said:
Attached you find all you need to flash cooked ROMs on your Sedna.
This has been on my HDD for quite a long time. I nearly forgot I did this
The package includes:
sspl-1.02mfg-sedna.exe (copy it to your sedna and run it)
HardSPL-1.02-mfg-sedna.nbh (flash it after running the sspl)
CustomRUU.exe (use it to flash the HardSPL)
Once the HardSPL is installed on your device you can flash any ROM.
Have fun,
JockyW
PS: Moderators please make this a sticky. Thanks.
Click to expand...
Click to collapse
congratulation.....hehe..thankyou for Jocky
Thanks everyone above,especialy jockyw2001.
I flashed the SPL,so I can cooked any ROM of P6500.
Will this give me a sim unlock?
Rom updateing problem
HELLO, Please anyone help me, I have a HTC P6500, I want to flash it that means current version is windows mobile 6 professional. My product is Orange UK,,,,,I have tried All ROM version but I have failed I have used all types of manhoods. When I click ROM update after going 5% flashing a message is seeing that is your phone can't supported tis software I want to use (Duttys_2.5_5.23144.5.3.10_3.14_HD2_ML_Family_ROM_(V6)_ITA.zipx)..Please give me a ROM software link I mean Italian language or New version Link
please give me a solution for me
sedna 100 hard spl
hi guys n gals,this is my first atempt to do this procedure on my sedna100,i followed instruction to unplug and replug back in,my screen is red-green-blue and whitewith usb in the white section its been like that for a wee while now and not syncing back up,can someone pls help...vrey much appreciated
finally managed it after hrs on google etc...head was in bits....thx jocky
can someone plz give me a link to cooked p6500 sedna roms plz
Trying to flash hard spl onto p6500 so that I can flash the new ROM. CustomRUU keeps failing with Error 262. Restarting the process doesnt work.
My device is stuck on the 4 colour screen with serial/usb title.
Any help would be much appreciated as I have a lot of devices to do, so need to get the first one working first.