[Q] Very slow performance on my HD2 - HD2 Windows Mobile 6.5 Q&A, Help & Troubleshooting

Hi all,
I've installed the latest official ROM (World Wide English (WWE) 3.14.405.2) downloaded from http://forum.xda-developers.com/showthread.php?t=623283 and also co0kie home tab 2 from http://forum.xda-developers.com/showthread.php?t=792303 on my HD2.
At the beginning everything OK but when time goes on (right now it is second week) it starts to slow down to almost freeze in several cases!! any idea?
By the way, 80% of program memory is always occupied!
Thanks

Go into bootloader, look at spl line.
if it DOESN'T say 3.03.0000 or 3.03.hspl then that's the problem,, use hspl4 and choose either of those.

Thanks, but could you help me more detailed on what you recommended? I've no idea what you're talking about?! Sorry for that
I'm not expert about this.
By the way, would this method remove all information (i.e. contacts, sms and ...)?
Thanks in advance

power off phone
press, hold and KEEP HOLDING volume down key
press and release power
KEEP HOLDING VOL DOWN
when striped coloured screen appears, that is bootloader, , now you can let go of volume down.
What does the 'spl' line say?

It says:
SPL-1.42.HSPL XE
What should I do now?

See? If you had read and understood post 2 it would be fixed by now
so you haven't got the right spl to run 3.14, just like I mentioned in post 2, it needs to be 3.03.xxxx for 3.14 and you have 1.42.xxxx
Enter bootloader, run hspl4 choose 3.03.0000 or 3.03.Hspl and reboot.

Thanks, but the problem is I've no idea "how to run hspl4"!!! Should I download something and install it on my HD2?
I've found this link (http://forum.xda-developers.com/showthread.php?t=609477) and I think it has a full guide for this!
Thanks for your help,
After installing this new HSPL4 should I install the ROM again?

vivid80 said:
Thanks, but the problem is I've no idea "how to run hspl4"!!! Should I download something and install it on my HD2?
I've found this link (http://forum.xda-developers.com/showthread.php?t=609477) and I think it has a full guide for this!
Thanks for your help,
After installing this new HSPL4 should I install the ROM again?
Click to expand...
Click to collapse
All you have to do is put hour phone into bootloader (multicolor screen) by holding the vulume down button down as your HD2 is booting up. Connect your HD2 via USB to the computer wait for the computer to install the drivers if they are (if they are not already) then you will see the Serial change to USB in the white bar of bootloader. When you see USB right click on the HSPL.exe and select run as administrator. The DFT utility will ask what version you want to install, it will be on 2.08 as default. Click on the little arrow to make the drop down box come down and select either 3.03.0000 or 3.03. The .0000 is regular SPL and the 3.03 is HSPL. And no you do not have to reflash the ROM but I would sugest a hard reset just to be safe.

Thanks guys,
Now the memory usage dropped down to below 50%!!! Let's see if there would be freezes or not

Related

Athena SPL Downgrader - finally

well, so I found out how to fully automate the process. sorry for the waiting, I was busy with life & some diamond and shift stuff
you can now just run an EXE that does all the downgrading and the modelid/wifi restore. no manual lnbs needed.
Description:
this uses a special SSPL, should be also OK in place of the original AthenaWrapper (or Unlocker Step 1), but I recommend you only use it for downgrade purposes.
this package includes:
- NBH to flash back to HardSPL 1.20.Olipro. can be replaced with other SPL NBH's but only with ones that are older than SPL 3.xx are recommended. this is only designed for SPL flash however, do not try other NBH types.
- SSPL which automates the restoring of wifi and modelid, which otherwise would always get corrupt when downgrading from SPL 3.xx. do not try to use another SSPL or you will corrupt your modelid and wifi and you will have to use manual tools (the Athena MAC BIN generator that I wrote & posted earlier) to restore them.
- RUU tailored to these needs. do not try to use another RUU for this purpose. also do not try using this RUU for anything else.
- BIG WARNING: do not even try to run this for any device other than Athena (not even the x7510). (I had to remove all modelid checking.) I do not take responsibility for such moronity (or any other kind of moron actions).
STEP BY STEP:
0. flash AP3newSPL OS image in preparation: http://htc-hackers.com/uploads/ap3newspl.zip
1. make sure Athena is running WM and synced with Activesync. do not try entering bootloader mode manually at this point! the way the Downgrader works relies on this.
2. extract the downloaded zip from Attachment to this post, you'll find an SPLDowngrader.EXE inside. run that EXE on your PC, now Athena should go to tricolour screen saying OliNex SSPL.
3. let the RUU flash.
3-TroubleShooting: if the RUU won't see device, uncheck the advanced functionalities in usb-to-pc settings in settings on the Athena.
4. it will reboot and also will hard reset your device. you will need to flash an OS compatible with old SPL now. if you are not sure how to do that, see "Extra help" below. after that, job is done.
5. +1: you should verify the modelid and SPL version is correct (ATHE100 and 1.20.Olipro). see "Extra help" below on how to enter bootloader mode to check.
Extra help: steps to help with flashing an OS if someone never flashed from bootloader before:
0. do not freak out if the OS isn't booting after downgrade. depends on what OS was on it before. maybe you will only get black screen but do not worry, read further:
1. you should manually enter SPL, by holding camera key (ALL THE WAY IN!!) while resetting. hold it until tricolour screen appears.
2. then use some other RUU / ROM package to flash an OS compatible with old SPL. job done.
NOTE 1: if the exe doesn't run then download and install .net framework from microsoft.com.
NOTE 2: if you just want to restore stock SPL, you must do it this way:
1. flash with this downgrader, with unchanged package.
2. flash OS compatible with old SPL 1.20.Olipro. this can be a stock OS.
3. use usual methods to restore stock SPL. this must be the last step, run only after you've restored stock OS!!!
Planned:
- dedicated stock SPL downgrade package
- dedicated SPL 3.50 upgrade package
these are all available already, just need userfriendly EXE package.
Tested and working great. Excellent Job as usual.
Thank you
Dear god thank you. Does this mean that our lords and lady of ROM cooking will be gracing us with an AP5 ROM sometime soonish?
Perfect!
Now i can try different ROMĀ“s and be sure, i can downgrade to an other, when i dont like a WM6.1 ROM.
Thx!
Awesome Cmonex - Thanks!
Many thanks, cmonex!
Just for clarification on step 4 above,
Do I enter boatloader manullay after this step?....or once this RUU is flashed and I see the black screen, do I just go ahead and flash my desired OS without entering manual boatloader?
Thank you cmonex for this downgrader!!!!!
Kenjari said:
Just for clarification on step 4 above,
Do I enter boatloader manullay after this step?....or once this RUU is flashed and I see the black screen, do I just go ahead and flash my desired OS without entering manual boatloader?
Thank you cmonex for this downgrader!!!!!
Click to expand...
Click to collapse
I edited step 4 to make it more clear - hopefully now you will see what is needed. let me know if still not clear enough.
(P.S: just to give background, RUU without manual bootloader entering will only work if WM is running because the RUU pushes enterbootloader.exe to the device which then puts the Athena in bootloader mode for flash without the user having to do anything. the exe will of course only run if there is an OS running under it.)
Hi Cmonex,
Excellent piece of work as usual, Its pretty clear as it is, You worry to much! Although
sticking with 3.5 for now, we have HTC stock, Ameo WM6 stock, and pawel's good work, and Irus's roms. Why swap?
NOW, have you got XP ROM onto Athena yet, if not why not
regards
Jay
Thanks cmonex, I get it now!
Sorry for the inconvienence!!!!
Thank you for everything ...
Is it possible once made the downgrade back to SPL 3.xx?
If this is so ... How do I do?
Montecristo said:
Thank you for everything ...
Is it possible once made the downgrade back to SPL 3.xx?
If this is so ... How do I do?
Click to expand...
Click to collapse
Just reflash with AP 4.0 again, you will have to go through all the upgrade again to get SPL 3.5 back on. Keep in mind if Pawel comes up with a new rom it may well need SPL 3.5 on to use it. I personaly think its worth waiting.
Regards
Jay
responderman said:
Just reflash with AP 4.0 again, you will have to go through all the upgrade again to get SPL 3.5 back on. Keep in mind if Pawel comes up with a new rom it may well need SPL 3.5 on to use it. I personaly think its worth waiting.
Regards
Jay
Click to expand...
Click to collapse
Same here, I do believe it woth waiting. We just need Pawel and AP team to give us an update on their next complete version.
Cheers
Black screen, Someone can help me!
Thanks for cmonex's contribution to Athena forum, AP4 in SPL 3.5 have given me a lot of pleasant time.
Since I discovered that the downloader has come out, because of curiosity,
I successfully downgraded to SPL1.2. Again, for curiosity, I wish to know the SPL1.2, I pushed camera buttom and soft reset at the same time, I really
seen the following:
"ATHE100
IPL-v.100
ATHE100
SPL-v1.20. Olipro"
However, I do not know how to switch back to the WM. If I press volume bottom and soft reset hole at the same time, I only get black screen with green light on. Someone can help me!
When you were in boatloader ..... I thought you were just only suppose to hit soft reset without the camera button.
Try that!
EDIT: I'm sorry panvita I read your post wrong. I thought you already flashed after the downgrade and you were only just checking to make sure you downgraded successfully by going to the boatloader screen. oops!
panvita said:
Thanks for cmonex's contribution to Athena forum, AP4 in SPL 3.5 have given me a lot of pleasant time.
Since I discovered that the downloader has come out, because of curiosity,
I successfully downgraded to SPL1.2. Again, for curiosity, I wish to know the SPL1.2, I pushed camera buttom and soft reset at the same time, I really
seen the following:
"ATHE100
IPL-v.100
ATHE100
SPL-v1.20. Olipro"
However, I do not know how to switch back to the WM. If I press volume bottom and soft reset hole at the same time, I only get black screen with green light on. Someone can help me!
Click to expand...
Click to collapse
You need to finish the rest of step 4 (or goto the extra help) and flash a 1.2 Rom
Extra help:
Click to expand...
Click to collapse
steps to help with flashing an OS if someone never flashed from bootloader before:
0. do not freak out if the OS isn't booting after downgrade. depends on what OS was on it before. maybe you will only get black screen but do not worry, read further:
1. you should manually enter SPL, by holding camera key (ALL THE WAY IN!!) while resetting. hold it until tricolour screen appears.
2. then use some other RUU / ROM package to flash an OS compatible with old SPL. job done.
Click to expand...
Click to collapse
yes please, why can't people read the instructions? :O
thanks to eagle for answering.
[OT]Women secrets...
How to have a REAL secret diary (and hide it to all males): leave it on the living room table and write in RED on the cover "Instructions Manual" [/OT]
My humble observation for AP4 under SPL 1.2.
panvita said:
Thanks for cmonex's contribution to Athena forum, AP4 in SPL 3.5 have given me a lot of pleasant time.
Since I discovered that the downloader has come out, because of curiosity,
I successfully downgraded to SPL1.2. Again, for curiosity, I wish to know the SPL1.2, I pushed camera buttom and soft reset at the same time, I really
seen the following:
"ATHE100
IPL-v.100
ATHE100
SPL-v1.20. Olipro"
However, I do not know how to switch back to the WM. If I press volume bottom and soft reset hole at the same time, I only get black screen with green light on. Someone can help me!
Click to expand...
Click to collapse
Before I pressed volume bottom and soft reset hole, I was able to see the program menu, and it is still AP4 program. I moved up by my finger, and htc flotouch still worked. I thought that I have had a AP4 under spl1.2, what a wonderful supprise. But after I pressed volume bottom and soft reset hole, what I could do is to go to AP3, and then to AP4, after that, go to downgrader. Finally, I went back to AP4 under spl 1.2. But strange things happened. Each time I soft reset the device, it went to customazation and calibration again. In orther words, I could not restore my backup file which eventually asked for a reset. Finally, I get a conclusion that AP4 cannot be used under spl 1.2 at least the present time. Because I got accustomed with AP4, then I upgraded to AP3 and then AP4 under spl 3.5. Just because my little curiosity, I have travelled around the world twice.
panvita said:
Before I pressed volume bottom and soft reset hole, I was able to see the program menu, and it is still AP4 program. I moved up by my finger, and htc flotouch still worked. I thought that I have had a AP4 under spl1.2, what a wonderful supprise. But after I pressed volume bottom and soft reset hole, what I could do is to go to AP3, and then to AP4, after that, go to downgrader. Finally, I went back to AP4 under spl 1.2. But strange things happened. Each time I soft reset the device, it went to customazation and calibration again. In orther words, I could not restore my backup file which eventually asked for a reset. Finally, I get a conclusion that AP4 cannot be used under spl 1.2 at least the present time. Because I got accustomed with AP4, then I upgraded to AP3 and then AP4 under spl 3.5. Just because my little curiosity, I have travelled around the world twice.
Click to expand...
Click to collapse
wish you had read the forum more times
it is well known that depending on the SPL version you have to get the correct rom version or you will get reset loop. AP4 is only for the newer SPL for now.

Athena dead after switching to new Michy (SPL mismatch...)

Hi All,
I had on my Athena the previous Michy Rom (2.04 with SPL 1.20) and when I saw the new version (4.00 with SPL 3.5):
http://forum.xda-developers.com/showthread.php?t=411371
I decided to install it. Like an idiot, I did not pay attention to the fact the SPL was different... I started the flash process and when I realized my error, it was too late.
The upgrade did not completed (as expected :-()) and now I am stuck with a corrupted bootloader screen, so I can't proceed (the device does not boot so I can't access ActiveSync).
Any way forward? Thanks for any hints!
Anubis
Update - I just tried this:
http://forum.xda-developers.com/showthread.php?t=326953
but without success. I get an Error [260] and the entire process stops.
Anubis1965 said:
Hi All,
I had on my Athena the previous Michy Rom (2.04 with SPL 1.20) and when I saw the new version (4.00 with SPL 3.5):
http://forum.xda-developers.com/showthread.php?t=411371
I decided to install it. Like an idiot, I did not pay attention to the fact the SPL was different... I started the flash process and when I realized my error, it was too late.
The upgrade did not completed (as expected :-()) and now I am stuck with a corrupted bootloader screen, so I can't proceed (the device does not boot so I can't access ActiveSync).
Any way forward? Thanks for any hints!
Anubis
Click to expand...
Click to collapse
look here
http://forum.xda-developers.com/showthread.php?t=405814
lakeman said:
look here
http://forum.xda-developers.com/showthread.php?t=405814
Click to expand...
Click to collapse
I have seen that thread. But the problem is different. I have also tried to reload a vanilla WM6 ROM but I cannot go past the corrupted bootloader part...
Anubis
Anubis1965 said:
I have seen that thread. But the problem is different. I have also tried to reload a vanilla WM6 ROM but I cannot go past the corrupted bootloader part...
Anubis
Click to expand...
Click to collapse
When you are in bootloader(three coloured screen) what do you see?
remove sim and sd card , hold camera button all the way in and press the reset button(on the back close to the battery cover)
If you see in bootloader mode ID showing somenting different than ATHE100 the solution is HERE http://forum.xda-developers.com/showthread.php?t=405814
I had the same problem! whell restart your pc and then connect the device to it. now start flashin an spl 1.20 rom. i did it and it worked! I hope i works for you too.
Cheers, Hirad
lakeman said:
When you are in bootloader(three coloured screen) what do you see?
remove sim and sd card , hold camera button all the way in and press the reset button(on the back close to the battery cover)
Click to expand...
Click to collapse
Thanks - already tried!
When I reset/hard-reset the phone (tried many ways) I see a garbled boot image (with random pixels here and there)... It is definitively not the usual bootloader with the information about the various ROM components and the "USB" text at the bottom.
Anubis
Solution!
I managed to do the same thing - had an old AP ROM with SPL 1.2 already installed then earlier today I tried to upgrade to the new Mitchy R4 SPL 3.5. I thought my Ameo was bricked, but after some pain it is now working again.
Here is what I did:
1) Enter bootloader mode using the very tricky Camera+Volume+Reset method.
2)
Follow exactly the steps in post 33 here:
http://forum.xda-developers.com/showthread.php?t=387454&highlight=mtty&page=4
Note, I'm running Vista so to get the USB option to show in MTTY, I had to first open "Windows Mobile Device Center" in Control Panel then disable the USB.
Also, note you should find your MAC under the battery flap.
3) Now all you need to do is reset, enter the bootloader mode again, and re-try the ROM (PS, make sure you use the correct SPL version!
Hope this helps.
spoonter said:
I managed to do the same thing - had an old AP ROM with SPL 1.2 already installed then earlier today I tried to upgrade to the new Mitchy R4 SPL 3.5. I thought my Ameo was bricked, but after some pain it is now working again.
Here is what I did:
1) Enter bootloader mode using the very tricky Camera+Volume+Reset method.
2)
Follow exactly the steps in post 33 here:
http://forum.xda-developers.com/showthread.php?t=387454&highlight=mtty&page=4
Note, I'm running Vista so to get the USB option to show in MTTY, I had to first open "Windows Mobile Device Center" in Control Panel then disable the USB.
Also, note you should find your MAC under the battery flap.
3) Now all you need to do is reset, enter the bootloader mode again, and re-try the ROM (PS, make sure you use the correct SPL version!
Hope this helps.
Click to expand...
Click to collapse
You are right and this is what sergiopi and I were referring to , specifically this post
http://forum.xda-developers.com/showpost.php?p=2154726&postcount=33
We were refering to the whole thread so you could learn the background.
However you are incorrect in your advice about how to enter bootloader
All you need to do is hold in the camera button and reset
spoonter said:
I managed to do the same thing - had an old AP ROM with SPL 1.2 already installed then earlier today I tried to upgrade to the new Mitchy R4 SPL 3.5. I thought my Ameo was bricked, but after some pain it is now working again.
Here is what I did:
1) Enter bootloader mode using the very tricky Camera+Volume+Reset method.
2)
Follow exactly the steps in post 33 here:
http://forum.xda-developers.com/showthread.php?t=387454&highlight=mtty&page=4
Note, I'm running Vista so to get the USB option to show in MTTY, I had to first open "Windows Mobile Device Center" in Control Panel then disable the USB.
Also, note you should find your MAC under the battery flap.
3) Now all you need to do is reset, enter the bootloader mode again, and re-try the ROM (PS, make sure you use the correct SPL version!
Hope this helps.
Click to expand...
Click to collapse
Thanks - you are giving me some hope! I am on a business trip now and my Athena is at home, but I will try that as soon as I am back
Anubis

[Q] Not able to go back to Stock ROM from WP7 - SOLVED

Hello,
I loaded the WP7 yesterday and then wanted to go back to stock ROM today. While I am able to enter bootloader:
It says:
LEO1000 HX BC (2K)
NSPL0.96.2250.0
MicroP (LED) 0x05
MicroP (TOUCH) NA
Now when I run the stock ROM it starts the update and then stops at 1%.
I have tried both 3.14 and 1.66 ROM and in both it says, Error (244): Invalid model ID (This update utility cannot be used for your PDA. Please check your update utility.
Any solutions?
Flash android?
nicedude_abad said:
Hello,
I loaded the WP7 yesterday and then wanted to go back to stock ROM today. While I am able to enter bootloader:
It says:
LEO1000 HX BC (2K)
NSPL0.96.2250.0
MicroP (LED) 0x05
MicroP (TOUCH) NA
Now when I run the stock ROM it starts the update and then stops at 1%.
I have tried both 3.14 and 1.66 ROM and in both it says, Error (244): Invalid model ID (This update utility cannot be used for your PDA. Please check your update utility.
Any solutions?
Click to expand...
Click to collapse
It sounds like you have to run hspl and make it 2.08 hspl
There is a special thread here on How to get back to winmo from WP7, read it!
e:
Did you reformat the card to FAT32?
lms1407 said:
It sounds like you have to run hspl and make it 2.08 hspl
There is a special thread here on How to get back to winmo from WP7, read it!
e:
Did you reformat the card to FAT32?
Click to expand...
Click to collapse
milli260876 said:
Flash android?
Click to expand...
Click to collapse
When I run HSLP 2 or 3 it keeps on saying Critical error - bad model ID.
I will try flashing android and see if that works. I haven't come across the thread you are mentioning but have come across the Android flash thread where they explain in the details other issues but nothing relating to this HSPL critical error Bad model ID.
BTW, I even tried flashing from SD Card but the the bootloader sayd 'SD NONE'. Did format the card to FAT32
nicedude_abad said:
Hello,
I loaded the WP7 yesterday and then wanted to go back to stock ROM today. While I am able to enter bootloader:
It says:
LEO1000 HX BC (2K)
NSPL0.96.2250.0
MicroP (LED) 0x05
MicroP (TOUCH) NA
Now when I run the stock ROM it starts the update and then stops at 1%.
I have tried both 3.14 and 1.66 ROM and in both it says, Error (244): Invalid model ID (This update utility cannot be used for your PDA. Please check your update utility.
Any solutions?
Click to expand...
Click to collapse
Where did you get the download from? It seems to have completely altered your model id in bootloader. You should either have PB81100, PB81110 or PB81120. To my knowledge those are the only model id's that hspl will work on. This is a very old thread I started which allowed hspl to run and bypass the device id check. You may want to try the steps there to see if they help. You will need to modify the steps slightly - in step 2 instead of entering "PB81110" enter "LEO1000". Please note this carries no guarantees and is at your own risk.
ClydeB1 said:
Where did you get the download from? It seems to have completely altered your model id in bootloader. You should either have PB81100, PB81110 or PB81120. To my knowledge those are the only model id's that hspl will work on. This is a very old thread I started which allowed hspl to run and bypass the device id check. You may want to try the steps there to see if they help. You will need to modify the steps slightly - in step 2 instead of entering "PB81110" enter "LEO1000". Please note this carries no guarantees and is at your own risk.
Click to expand...
Click to collapse
Downloaded it from the forum itself. I tried to do what you suggested but now it's giving me an error ''Bad SPL version''.
Any solutions?
nicedude_abad said:
Downloaded it from the forum itself. I tried to do what you suggested but now it's giving me an error ''Bad SPL version''.
Any solutions?
Click to expand...
Click to collapse
Seriously, where did you get your download from, that must have seriously screwed with your phone to change your model id and spl version like that. I installed WP7 yesterday and have just safely reverted back to Android without any hassles. Do you recall what values you had before the flash?
If there is a solution it ain't gonna be a simple one and will need some serious tech help, which is outside of my levels. Even Googling the spl version only returns this thread.
This (or something similar) happened to me. I powered down my phone but did not take out the battery and it restarted the part that loads the win 7 rom while I still got the screen with the coloured bands on.
Try, taking out the battery for 10 seconds or so then put it in while holding the volume down key and powering up.
Got stock ROM back in first time but kiss goodbye to the data on your SD card. I had to use a Canon camera to reformat the card to get back the 14GB it was hiding.
splinters69 said:
This (or something similar) happened to me. I powered down my phone but did not take out the battery and it restarted the part that loads the win 7 rom while I still got the screen with the coloured bands on.
Try, taking out the battery for 10 seconds or so then put it in while holding the volume down key and powering up.
Got stock ROM back in first time but kiss goodbye to the data on your SD card. I had to use a Canon camera to reformat the card to get back the 14GB it was hiding.
Click to expand...
Click to collapse
This WORKED. Thanks a TON splinters69.
For future uses, this is what I did.
1. Took out the battery for about 30 seconds.
2. Put one of the LEOIMG.NBH on storage card
3. After putting the battery held the volume down button and pressed power button.
4. It went into HSPL mode straight away and started loading the win 6.5 OS.
You saved the day Splinters69. Thanks to Clydeb1 too for that modelIDcheckbypass.
nicedude_abad said:
This WORKED. Thanks a TON splinters69.
For future uses, this is what I did.
1. Took out the battery for about 30 seconds.
2. Put one of the LEOIMG.NBH on storage card
3. After putting the battery held the volume down button and pressed power button.
4. It went into HSPL mode straight away and started loading the win 6.5 OS.
You saved the day Splinters69. Thanks to Clydeb1 too for that modelIDcheckbypass.
Click to expand...
Click to collapse
Phew, that must have been a scare. Glad to see you got it resolved and something so simple as removing the battery - nice one @splinter69.
ClydeB1 said:
Phew, that must have been a scare. Glad to see you got it resolved and something so simple as removing the battery - nice one @splinter69.
Click to expand...
Click to collapse
Yea. It was scary but the only good thing was that I was able to get into MAGDLR so I knew that probably I could install another NAND Android ROM onto it. However, what I wanted was to go back to WinMO 6.5 and then re-learn.
Amazing what knowledge pool we have here, isn't it?
scary that. I think we all fear that at one point or another. thanks for the insight as to how u sorted it.when u said u put a rom back on was it a stock or custom rom.
It was a custom NRGZ ROM.
Sent from my HTC Desire using XDA App
cheers for that
Hi all !
I Had the exact same problem after installing WP7 and trying to go back to 6.5 :
Boot Screen was displaying :
LEO1000 HX BC (2K)
NSPL0.96.2250.0
MicroP (LED) 0x05
MicroP (TOUCH) NA
Whenever i try to flash back to any stock / signed ROM it failed at 1%
splinters69 technic is working perfect .
1> Switch Off you phone
2> Remove Battery & wait for 30secs
3> Hold Vol Down + Place Battery back in + Press Power Btn
4> BootScreen Should display your previous version of HSPL.
5> Dont need GoldenCArd , just use RUU FLASH MODE
Thx guys !
I installed MagLDR 1.12 and WP7... after restarting the phone, it kept reseting after about 15 seconds of DFT screen, so i couldn't flash another rom.
After that i took out the baterry and flashed a 6.5 rom and then flashed MagLDR 1.13 and WP7. This time it worked.
Thanks everybody, for posting such helpful things.
Hi all, tried the above mention steps but still couldn't flash it back to stock rom.
It always stuck at 0%, anyone can help?
Is flashing back to WinMo from WP7 the same as from NAND android?

448RAM not 576RAM

My ultimate goal is to put Gingerbread on my phone Via the NAND Method.
I am starting with the latest version of the windows ROM from the HTC website for 02.
First I added HSPL3 to my phone so when I hold the VOL Button and Power I load to HSPL screen with version 2.08.HSPL. I presume this is correct.
Now I upgrade the radio to 2.08.50.XX I still only have 448RAM, how do i get this to 576RAM so i can install MAGLDR 1.11
You do not actually need the 576 in order to flash to Android, you only need to have a radio that enables the 576. In order to actually get it to show you need the correct radio together with a rom that "unlocks" the extra ram. As long as you have 2.08.hspl and a 50 series radio of at least 2.08.50 then you're good to go. You also should head over to the correct forum before someone flames you (ie this one is for winmo ). Refer to the link in my signature on Flashing NAND Android roms and you will get all of the necessary steps there.
not exactly true... you need to have HSPL and correct Radio to enable 576MB RAM - SPL3.03 that comes with 3.14 ROM doeas not enable 576MB RAM - I have tried that.
(Same Person was borrowing Stephiepea account to post my question)
Cheers Clyde for the help, i'm obviously a Newb when it comes to this. I tried to install MAGLDR 1.11 to my phone by your method and once it completed on my phone it rebooted but not to the boot loader, it just loadedto the O2 boot screen and stayed there didn't even boot to windows mobile again.
Daekin can you give me in laymans terms what HSPL and Radio I NEED differently to the ones I indicated in my first post.
I've also tried loading a custom "Energy" Rom then tried loading MAGLDR and again it boots to the NRG sting and stays there. please someone help. ive been trying for days.
Incase it helps when I boot to HSPL my screen info is
PB81100 HX-BC
SPL-2.08.HSPL 8G XE
0x05
CotullaHSPL 0x30
Try MAGLDR 1.12 and the included latest radio (2.15.50.14).
1. Connect by USB to the PC.
2. Hold down volume button and power up to get in 4 color screen, make sure it says USB at the bottom.
3. Flash the new radio.
4. Hold down volume button and power up to get in 4 color screen, make sure it says USB at the bottom.
5. Flash MAGLDR.
6. Hold the powerbutton down to enter MAGLDR.
7. Choose option 5 to USB flash a ROM (by using volume down button again).
It worked for me, I've also 2.08HSPL.
For the MAGLDR and radio check your PM.
GL!
Thanks Eric,
I havn't recieved anything via PM but I downloaded MAGLDR 1.12 and the same happens. I get stuck on the O2 Splash screen.
things i've tried:-
HSPL3 - Tried to install this, I get The success message apear on my PC but not the we hacked it message on my phone, is this because I already had a HSPL on my phone.
I've tried multiple radios with .50 which shoul alow the 576MB RAM but my phone never shows this only the 448MB RAM in the Device infomation.
After both the above, my phone boots back to windows.
then I try MAGLDR once it completes I boot to the O2 Splash screen and never progress to the bootloader or windows, even if reboot and hold down the power button.
Hmm, that doesn't sound well.
Maybe you can try to flash with a custom WinMO rom first, like Energy.
I had the Energy Rom installed before I used MAGLDR.
You can find it here: http://forum.xda-developers.com/showthread.php?t=591784
I think it should also flash with the 4 color bootscreen connected to USB.
After flashing a custom rom try to flash with MAGLDR again.
Hope it works, GL!
edit: I don't know if mine says 576 ram, because I don't know how to check that in WP7, which s*cks anyway.
Any STOCK ROM with a .50 Radio will NOT enable the 576MB RAM
You need a CUSTOM ROM (576MB trick enabled) with a .50 Radio to enable the 576MB RAM
[The Punisher] said:
Any STOCK ROM with a .50 Radio will NOT enable the 576MB RAM
You need a CUSTOM ROM (576MB trick enabled) with a .50 Radio to enable the 576MB RAM
Click to expand...
Click to collapse
Wrong! sorry guys i had to jump in here because there is some crap advise being given.
First off the latest wwe (not o2 branded) does enable the extra ram (as do all tmous roms). Where do you think radio 2.15.50.14 came from? secondly AFAIK (and i could be wrong here and i haven't checked it) magldr wipes the nand chip when it is installed therefore all you will ever see after a magldr install is the boot splash unless you reboot the phone and then install wp7 or android (wm6.5 is not yet supported but will be in magldr 1.13)
What the op has done up until he expected windows to boot was good. All he needs to do is install magldr 1.12, reboot holding down the power key and then follow the instructions for installing android to nand.
Handily, using google, i found this link. That should sort you out. I also found this video. Half of what comes out of his mouth at the start is rubbish but the actual steps are good.

[Q] New to HTC - ROM upgrade help please

Checked the other threads suggested but no luck
I have recently bought an HD2 WP6.5 which was unlocked by TMobile (UK) & subesquently debranded by me using Active Sync, HSPL2 & the LEO 1.66 RUU.
Everything seems fine but can I now upgrade to the new official 3.14? I have downloaded it from the HTC site but worried about damaging the phone.
Sorry if this is in the wrong place - I'm new to this sort of thing!
Thanks
hspl4 - 3.03.hspl - flash 3.14 rom from usb.
samsamuel said:
hspl4 - 3.03.hspl - flash 3.14 rom from usb.
Click to expand...
Click to collapse
Thanks for that
I'm not very technical - do you mean download HSPL4 then install 3.03 from that then flash 3.14, essentially the same as I did above but with the programs you indicated?
Thanks
Junks
EDIT: Just tried doing that & it did nothing.
Downloaded HSPL4 & ran it, tried to run 3.03 but it rebooted & still showing 1.66 - is this because I have 1.66.HSPL & not 0000?
Thanks
Phone into bootloader (power off, hold and keep holding volume down,tap n release power keep vol pressed till coloured striped screen, do all your flashing from here)
Into bootloader, connect USB, wait for word,"serial" to become "USB"
On PC,right click hspl4.exe and choose run as administrator,
What happens? What does it say in Bootloader? (Top line and spl line) before and after please.
Ah didn't know about that!
Right done that & it now says SPL-3.03.HSPL XE so obviously it did work as above I just didn't know how to check it!!
It shows:
PB81100 HX-BC
SPL-3.03.HSPL XE
0x05
Cotu11aHSPL 0x40
USB
So just run 3.14 on the PC now - do you have a link so I get the correct one?
Sorry to be a pain
Edit: This is the one I downloaded from HTC _HTC HD2_RUU_Leo_HTC_WWE_1.48.405.2_Radio_Signed_15.28.50.07U_2.05.51.05_2_Ship
That rom is 1.48,,, see the sets of numbers?
_1.48.405.2_Radio_Signed_15.28. 50.07U_2.05.51.05_2
Ver 1.48.405.2, with radio 2.05.51.05.
That's an ooold rom. There's at least 1 thread with all the 3.14 roms in it.
I saw that & thought it looked strange - put a WWE serial in the HTC & got that but I must have done something wrong as I've just done it again & the file now says 3.14!
Oh well all done now & seems to be working ok - thanks for your help, much appreciated
Just looking forward to using the phone now & ditching the annoying iPhone
Hehe it can be temperemental, bit like an 80's super car, terrible cars, but great none the less. I'm buying another for when this one dies.

Categories

Resources