hey guyz
sorry to start a new post but i have searched everywhere on this platform and mostly its same solution everywhere so i think i just need some specific steps to do it i guess.
i was on A0435 with baseband .54 which comes with generic rom. then i searched and found out that MIUI 1.0.5 can work on .54 without changing to .49, we just apply cm6bb54.zip patch.
first i did was flashed A0435, ran the phone, rooted, installed xrevocery, then i flashed trip's MIUI 1.0.5 through xrecovery and without rebooting i flashed the patch also. that solved the problem of network connection.
but my major problem is that it keeps bootlooping. i cant get it to stop bootlooping.
i have also tried 10times to flash .49 on it but it wudnt work. i always get unkoen baseband and because of that again MIUI wudnt work.
i need some1 to help me out with steps to do it perfect from whom this ROM is working on x10.
thank you for your time.
worked fine for me....
Did you make sure to full wipe before you flashed the rom?
full wipe/factory restore, wipe cache, then go into advanced and wipe dalvik cache. Then flash the rom, followed by the patch.
yes, i have tried all that and its still bootloop.
try loading it for a minute and letting it settle, then afterwards going back into xrecovery and flashing the patch.
thnx man. but i just found my own way of working this thing out. for any1 who has/had problem like me installing MIUI 1.0.5 on .54..just flash generic A.0.24 which has .49 preinstalled baseband and then just follow normal xrecovery method of flashing the MIUI 1.0.5 and it works perfect.
pinkzwinkz said:
thnx man. but i just found my own way of working this thing out. for any1 who has/had problem like me installing MIUI 1.0.5 on .54..just flash generic A.0.24 which has .49 preinstalled baseband and then just follow normal xrecovery method of flashing the MIUI 1.0.5 and it works perfect.
Click to expand...
Click to collapse
lol or you could just flash the .49 baseband instead of a whole firmware.
The patch worked fine for me and everyone else, judging by this post, I'm assuming it's something you're doing
Related
I'm currently running FreeX10 B3H1, I see that B4 is out and all it apears to do is add support for the new Baseband... is there any notice improvements with the updated baseband?
I'm also not entirely sure what the baseband does
The baseband is the radio of the phone, so basically it controls your call quality, signal, mobile network, etc..
As fire why to upgrade, I can honestly say I haven't noticed any real benefits since I updated. However, as time progresses newer roms are going to be based on this version so if you want to keep flashing custom roms eventually you will have to upgrade anyway..
Hi,
I attempted to install Beta 4 last night (first time installing FreeX10). But now it is in a non stop reboot cycle and will not get any signal. It stays on for about a minute and then reboots everytime. Having read more on this I think it could be Baseband related. When I check the settings it says Baseband is unknown.
Can I upgrade my Firmware to X10a_2_1_A_0_435_GLOBAL in order to get the correct Baseband and then reinstall FreeX10? And if so, Can I use Flashtool to install X10a_2_1_A_0_435_GLOBAL without issues?
(My phone is an X10i by the way, should I use a different Firmware before re-installing FreeX10B4?)
Thanks in advance!
Dave
Daavid_1 said:
Hi,
I attempted to install Beta 4 last night (first time installing FreeX10). But now it is in a non stop reboot cycle and will not get any signal. It stays on for about a minute and then reboots everytime. Having read more on this I think it could be Baseband related. When I check the settings it says Baseband is unknown.
Can I upgrade my Firmware to X10a_2_1_A_0_435_GLOBAL in order to get the correct Baseband and then reinstall FreeX10? And if so, Can I use Flashtool to install X10a_2_1_A_0_435_GLOBAL without issues?
(My phone is an X10i by the way, should I use a different Firmware before re-installing FreeX10B4?)
Thanks in advance!
Dave
Click to expand...
Click to collapse
hey, for d "unknown baseband" problem u have to wait for d auto reboot after d 1st boot..only then d baseband and network will appear..
and for d boot loop problem-u will need to update to d .435 firmware (.52 baseband and .29 kernels)..or if u want to keep d old firmware install beta3..(beta 4 is only for .435 firmware)
happy flashing bro.
Daavid_1 said:
Hi,
I attempted to install Beta 4 last night (first time installing FreeX10). But now it is in a non stop reboot cycle and will not get any signal. It stays on for about a minute and then reboots everytime. Having read more on this I think it could be Baseband related. When I check the settings it says Baseband is unknown.
Can I upgrade my Firmware to X10a_2_1_A_0_435_GLOBAL in order to get the correct Baseband and then reinstall FreeX10? And if so, Can I use Flashtool to install X10a_2_1_A_0_435_GLOBAL without issues?
(My phone is an X10i by the way, should I use a different Firmware before re-installing FreeX10B4?)
Thanks in advance!
Dave
Click to expand...
Click to collapse
Just use this
http://forum.xda-developers.com/showthread.php?t=936733
Reflash to the new baseband , root it and install Xrecovery and proceet to install your favorite rom. I would suggest making your own with this
http://forum.xda-developers.com/showthread.php?t=938393
PS: This works with new baseband and Beta 4 rom of Z
Cheers.
Have fun flashing and creating your custom roms
srikanth.naidu said:
Just use this
http://forum.xda-developers.com/showthread.php?t=936733
Reflash to the new baseband , root it and install Xrecovery and proceet to install your favorite rom. I would suggest making your own with this
http://forum.xda-developers.com/showthread.php?t=938393
PS: This works with new baseband and Beta 4 rom of Z
Cheers.
Have fun flashing and creating your custom roms
Click to expand...
Click to collapse
I've installed this : http://forum.xda-developers.com/showthread.php?t=936462
Got .435 and baseband 2.1.54
Installed Free X10 without any problem.
You gotta make sure you update to 435 before installing freex10 beta 4 to get all benefits...
ratmkicksass said:
You gotta make sure you update to 435 before installing freex10 beta 4 to get all benefits...
Click to expand...
Click to collapse
no you don't...
flashing just the kernel and the baseband through flashtool has the EXACT same effect...
I have no problem with using the flashtool, downloading the sin file, etc. But the step that says DO NOT let it boot and immediately go into xrecovery is what worries me. I love trying all the new ROMs, but am still always go back to a custom 2.1 because of the cam/videocam, plus no stereo bluetooth dropouts.
My question is, after I do this to update the baseband and flash 2.2 Beta 4 via xrecovery. Can I go back to my old custom 2.1 with older baseband via xrecovery and then switch back and forth via xrecovery afterward? I just don't feel like flashing the entire firmware, rooting, adding JIT v2, then removing all of the SE apps AGAIN for like the 10th time.
u can install any rom on .435 firmware..
u cant install beta 4 on any lower firmware(.24,etc)..
so update to .435 and stay..
happy flashing
sumeshd said:
u can install any rom on .435 firmware..
u cant install beta 4 on any lower firmware(.24,etc)..
so update to .435 and stay..
happy flashing
Click to expand...
Click to collapse
Im not entirely sure thats true because it seemed that those with the newer baseband seemed to be having issues with other roms prior to z's beta 4... can someone confirm?
Sent from my X10i using XDA App
its mentioned clearly in z's post about using the latest base band. as for Steve's recommendation of not letting it boot, i guess i must have missed it when i upgraded the base band while on 2.1 customised, but the only worst thing that happened was i didn't got any signal on my phone, everything else worked fine, it didn't mattered coz i was to install free x10 v4. and its a fine job done by z. the ROM is great. add green glow theme on it, and nothing's like it.
about xrecovery backup able to change your base band back with restore, i haven't tried it myself, i guess xrecovery devs will be the best guys to check if you're not sure.
Sent from my X10i using Tapatalk
Hello
I'm new of the forum and sorry for my English
I have an Xperia X10i with Android 2.2.1 CM 6.1.3 V4.5.
I've seen that I can't choose the operator in manual mode. It says "error in nets research". And if I put on automatic search it stays still to say "searching new nets"... What could be?
Is there anyone with the same problem or that has a solution?
Thanks
Giulio
Sounds like you had a bad flash or u flashed it an improper way.
Did u wipe phone, caches and battery stats before flashing?
Sent from XDA Premium from my X10a rooted running 2.2.1 Cyanogen 6.1.3gingerbreadV1 ROM
cos000 said:
Hello
I'm new of the forum and sorry for my English
I have an Xperia X10i with Android 2.2.1 CM 6.1.3 V4.5.
I've seen that I can't choose the operator in manual mode. It says "error in nets research". And if I put on automatic search it stays still to say "searching new nets"... What could be?
Is there anyone with the same problem or that has a solution?
Thanks
Giulio
Click to expand...
Click to collapse
which basenband r u on?
and
2.2 roms dont supp manual searching of networks thats confirmed
Upgrade from 4.4 to 4.5.6?
Hello All!
I have a question. I'm on version 4.4, baseband 2.1.54 and would like to know the step by step I need to do in xRecovery to upgrade to version 4.5.6 (wipe, ROM installation sequence, etc ...)
Thanks, fantastic ROM.
Hello
My baseband is .54 and I wiped everything before flashing the new firmware...
Must I reinstall all?
try re-install fresh..... that should do
Hello
I've re-flashed and it can't search the nets...
I did like it's on http://forum.xda-developers.com/showthread.php?t=945264
I don't know... Maybe it's because I disable package connection...
hernandeschaves said:
Hello All!
I have a question. I'm on version 4.4, baseband 2.1.54 and would like to know the step by step I need to do in xRecovery to upgrade to version 4.5.6 (wipe, ROM installation sequence, etc ...)
Thanks, fantastic ROM.
Click to expand...
Click to collapse
Wolfbreak has given step by step instructions which are pretty clear on how to upgrade to the 4.5.6/4.5.7 ROM.
However I too was confused when upgrading to 4.5.7 from 4.4. I was confused whether I shall lose my apps or not.
I think wolfbreak has made a new ROM 4.5 which overwrites the previous versions. Therefore it shall wipe everything. You will no longer have the apps and settings you have on v4.4. Therefore make a backup of the apps using titanium backup or something. Then go to xRecovery and make a backup of the ROM in case anything goes wrong. Then make a full factory wipe. Then wipe the cache, then the dalvik cache and lastly wipe the battery stats. Then go to install custom zip and flash the CM-6.1.3-V4.5.zip. Then again go to install custom zip and flash the CM-6.1.3-V4.5.7.zip. Then again, one last time go to custom zip and flash the gapps. Then reboot. Then follow the last three instructions on wolfbreak's page.
Hello
Now my phone is still in roaming and I can't switch it to my nation's net...
Any help?
Hello everyone,
first, i used the search button but had no luck to find a solution for my problem .
I have a BlueSparks v5 ROM installed but wanted to try trip's latest MIUI ROM (v1.0), so i flashed it at my .54 baseband but had no radio. so i flashed the .49 bb (from here) and the flashed the rom again but this time i had "Unknown baseband) in the info section beside the radio problem.
so i figured out that i better flash the whole 2.0.2.A.0.24 FW (from here) to have the bb problem corrected, but again im having the same.
at last i restored my backed up ROM till i get this problem solved, so any ideas guys?
Full wipe in xrecovery, n wipe cache, batt stats, dalvik, once u flash miui n reboot, look for the dev tool app on the home screen open it, pik bad behavior, crash system server, it will reboot n u should have radio now!!
Best regards,
Chris
Sent from my X10 using XDA Premium App
thanks Chris, it really worked
as a beginner I can´t post in the main thread, sorry
I´ve update from DSC 2.0.1 to 2.1 and now I have not apps that need root and also no wifi :crying::crying::crying::crying:
I didn´t do any nandroid :crying::crying::crying::crying::crying:
next time use dsc 1.0 first... usually anything above 1.0 is for people who already tried dsc 1.0 ...
Root issues
josinho00 said:
as a beginner I can´t post in the main thread, sorry
I´ve update from DSC 2.0.1 to 2.1 and now I have not apps that need root and also no wifi :crying::crying::crying::crying:
I didn´t do any nandroid :crying::crying::crying::crying::crying:
Click to expand...
Click to collapse
I have the same problem, i think nop is looking into it for us.
Meanwhile nandroided back to v2.0.1
i got mine too..wifi doesnt work so i did nandroid
I really don't get it.
I've checked and reflashed update twice already.
Which recovery was used?
_n0p_ said:
I really don't get it.
I've checked and reflashed update twice already.
Which recovery was used?
Click to expand...
Click to collapse
as a very beginner in android I´m not sure that my answer is really what you are asking,
first I updated my original Froyo to Olleh stock rom via streakmode, as the thread in this forum,....after I updated to DSC 2.0 directly over Olleh gingerbread, without passing by DSC 1.0
It worked great, compared to stock rom wich is a potato,.... but now I´ve losed my paradise :crying::crying::crying::crying:
anyway thanks a lot to nop, I will reinstall 2.0, is a very very very good ROM:laugh::laugh::laugh:
josinho00, you entered recovery when you was flashing update.
Which recovery was that?
_n0p_ said:
josinho00, you entered recovery when you was flashing update.
Which recovery was that?
Click to expand...
Click to collapse
I used the streakmode, the one that I´ve downloaded from de forum when I updated from froyo to olleh gingerbread, I really dont know anything more now, I´m not at home and can not look for any more
is that what you want to know nop?
thanks a lot
Yes, thank you.
I have root problem with Dsconfig and Dsc cpu voltage.
Sent from my Dell Streak using xda premium
Fixed.
http://forum.xda-developers.com/showpost.php?p=35054721&postcount=5631
_n0p_ said:
Fixed.
http://forum.xda-developers.com/showpost.php?p=35054721&postcount=5631
Click to expand...
Click to collapse
I´ll try the new patch this afternoon
yesterday nigth I reflashed v 2.0 and after 2.0.1, it became to normal .... wifi was all rigtht and DSC apps also were allright.
but "battery counter" did not work properly (it was full charged and showed just 1%) and some apps like "ES file explorer" did not work with root privilegies, I reflashed superuser zip, and after every thing including battery counter were fixed"""
You should always flash updates on full charge, that'll get rid of 1% problem.
_n0p_ said:
You should always flash updates on full charge, that'll get rid of 1% problem.
Click to expand...
Click to collapse
OK, again thanks a lot,
I´m starting with android, comming from iOS ... I´m learning a lot
congratulations for your ROM it´s really fast and stable ... I´m not missing apple´s OS
Hi pro..how can i use fm on dsc 2.1.thanks
Sent from my Dell Streak using Tapatalk 2
Yes.
I've tried to update DSC 1.7 to 2.0 than 2.2, everything is ok.
After flashing updDSCv2.2-PDroid.zip, system hangs on boot animation.
Using nandroid back to 2.2(no PDroid), system is no problem.
How to fix it? Thanks!
Have you flashed PDroid for 2.0 first?
I understand that's not clear, but you should flash 2.0, then 2.0's Pdroid, then 2.2 with PDroid.
_n0p_ said:
Have you flashed PDroid for 2.0 first?
I understand that's not clear, but you should flash 2.0, then 2.0's Pdroid, then 2.2 with PDroid.
Click to expand...
Click to collapse
Problem solved. Thank you, n0p !
Steps for DSC 2.2 with PDroid
1) Flash DSCv2.0-rel.zip
2) Flash PDroid-v1.31-DSCv2.0.zip
3) Flash updDSCv2.2-PDroid.zip
4) Wipe cache partition, dalvik, fix permissions
5) Reboot
continuing to reboot...
Recently, my phone has been restarted many times. Trying to solve it by reflashing DSC 2.3, but it remains. I flashed the baseband back to 407, it works!
Now it works like a charm but loudly...