HELP ME. Flashed CwmFolio_v02_update.zip from one of the tread from this forum. I think most of you know which one.
After clicking reboot system in the menu in clockwork.. the tablet just stalled..
black screen. nothing.
BUT, the home, back, search, and menu button still works.
power button not working.. long press and still nothing.
power light still up.
connected to pc through mini usb. not detected.
the only solution i could think of now is to wait for the battery to dry out, which could take forever as the battery was still 79% the last time i saw it.
is it possible for me to take out the battery?.. like i normally does when my laptop stuck??
Help me please..
You can unlock the back on the left side and remove the back cover. Then you can also remove the battery.
atiti said:
You can unlock the back on the left side and remove the back cover. Then you can also remove the battery.
Click to expand...
Click to collapse
if there any step by step instruction on how to do that?.. or maybe just any tips about what i should be careful with when removing the battery?
1. Slide the lock to the unlock position on the left side (when facing the device)
2. Open the back by using the little gap on the top left side of the device (it might sound like its breaking, but its not..)
3. Then pull out the battery by using the handle for it
Its relatively straight forward Not much you can mess up if your careful.
atiti said:
1. Slide the lock to the unlock position on the left side (when facing the device)
2. Open the back by using the little gap on the top left side of the device (it might sound like its breaking, but its not..)
3. Then pull out the battery by using the handle for it
Its relatively straight forward Not much you can mess up if your careful.
Click to expand...
Click to collapse
Thank YOu soo much!.
i think the problem is with clockworkmod. i installed a version using rom manager. before that already flashed a modded version from this forum. the last time i installed another modded one with support for internal sd.. also from this forum.. maybe any one of that caused the problem.. anyway.. removing the battery and reinserting it seems to do the job. Thanks again!
gingerboy92 said:
HELP ME. Flashed CwmFolio_v02_update.zip from one of the tread from this forum. I think most of you know which one.
After clicking reboot system in the menu in clockwork.. the tablet just stalled..
black screen. nothing.
BUT, the home, back, search, and menu button still works.
power button not working.. long press and still nothing.
power light still up.
connected to pc through mini usb. not detected.
the only solution i could think of now is to wait for the battery to dry out, which could take forever as the battery was still 79% the last time i saw it.
is it possible for me to take out the battery?.. like i normally does when my laptop stuck??
Help me please..
Click to expand...
Click to collapse
Did you by chance have an usb device connected? I managed to get this kind of lock twice, but only when I had my usb flash disk attached/removed while I was in recovery.
mblaster said:
Did you by chance have an usb device connected? I managed to get this kind of lock twice, but only when I had my usb flash disk attached/removed while I was in recovery.
Click to expand...
Click to collapse
i didn't remember exactly what happened, but im not mistaken I didn't have any usb connected at that time. just the sd card.
Hello. I have the same problem. I flashed my tablet Folio 100. (FolioMod v1.4). After restarting remained only a black screen (not even Toshiba logo). I choose the battery and waited 10 minutes. The problem remains. What should I do? Help me!
I saw on several forums your are the best in what you do.
I have a major problem.
My little brother played on my folio( never had to give him this) i had your latest update 3x and it freezed. and for one or another reasen he pushed several types on power butten. now my folio is crashed. if i turn it on, i just have the powerlight, nothing more.
i already took my battery out and even pushed on reset button but nothing works
please help
thanx in advance
francigel said:
... and then after to have read how to install a huawai key, thanks the installation instruction posted by DERARTEM i have proceeded....but at the end I have got a big problem...the tablet is rebooted ...then I saw the logo TOSHIBA but at the end the screen remained black....
Click to expand...
Click to collapse
DerAartem technique works with version FolioMod 1.3
It changes the boot
If your boot is corrupted, you still have a black screen
You can change the boot.img with fastboot command
Code:
fastboot erase linux
fastboot flash linux boot.img
fastboot reboot
Related
So I just got done configuring chompSMS. Disabled notifications on the built in SMS app. Did a battery pull and got this screen and haven't been able to get out of it. Held down home & power and got a user memory wipe screen. Figure I'd give that a shot. Still stuck on the FASTBOOT screen and now have to redo the whole thing if I manage to get out of this screen.
Anyone else see this? Not much out there about Sprint's Hero, but there's a bit about Orange's Hero, rooting, flashing rom's and all that fun stuff. Nothing about getting it back to normal though.
and to add....after letting it sit connected to usb for a bit, the screen finally went dark but now won't turn back on. Really odd.
hmm im kinda new to android, but if your stuck in fastboot cant you use the devkit to push a new recovery image like RA 1.2.3 and flash ?
i might be wrong tough
I'm brand spanking new to Android. Haven't dealt with sdk's andn loading rom's in ages and don't have the time to figure it out. Thought there might be some hard reset button combo that I was missing or something. Just heading to the Sprint store now with box in hand to have them switch it out or activate my Treo Pro again. Kinda need the phone for work and don't have a home phone so downtime is not a good thing.
darkenergy said:
hmm im kinda new to android, but if your stuck in fastboot cant you use the devkit to push a new recovery image like RA 1.2.3 and flash ?
i might be wrong tough
Click to expand...
Click to collapse
he won't be able to push that to do ADB tricks, nor do fastboot flashing with img files
Goldcard doesn't help as well
I hv got a G1 in same situation after pulling out the battery.
Stucked at first splash screen on next boot.
I assume that is a rom / system problem so I tried to boot into recovery but still freeze on 1st splash screen.
I tried to figure out the problem and I'd try to connect by usb and tried adb logcat but only waiting device return. And yep the screen goes black ( but still on ) likely in this situation.
And yea SPL enter was successful but can't connect to fastboot so no recovery can flash.
I notify the phone (seemingly) won't be able to charge as the notification do not turn on, or it does charge but problem with notification light (?), probably it is more likely a hardware problem due to removing the battery. Recently I take the G1 to a shop to figure out is that a hardware failure.
I'm all for troubleshooting and playing around with ROMs, but there's times when I just need to be up and running and have opted not to screw around with something I depend on for work. There's other toys to "play" with.
So after a way too long stay at the Sprint store I have a new Hero that's up and running just fine.
Wanted to say it was something I installed, but everything seemed to be approved by the masses as working well. Maybe it was something with the battery pull. I'm surprised no one has made a soft reset widget. Seems kinda basic coming from 13yrs of PalmOS and a bit of winMob.
dbpaddler said:
So I just got done configuring chompSMS. Disabled notifications on the built in SMS app. Did a battery pull and got this screen and haven't been able to get out of it. Held down home & power and got a user memory wipe screen. Figure I'd give that a shot. Still stuck on the FASTBOOT screen and now have to redo the whole thing if I manage to get out of this screen.
Anyone else see this? Not much out there about Sprint's Hero, but there's a bit about Orange's Hero, rooting, flashing rom's and all that fun stuff. Nothing about getting it back to normal though.
and to add....after letting it sit connected to usb for a bit, the screen finally went dark but now won't turn back on. Really odd.
Click to expand...
Click to collapse
download htc sync and install it.
http://www.htc.com/us/supportdownloadlist.aspx?p_id=300&act=sd&cat=all
download sprint RUU and run it, it will wipe your phone, but it will work agian
ftp://xda:[email protected]_Hero_C_Sprint_1.29.651.1_signed_release.exe
thanks for that. Will keep that handy for next time or if I ever play around with it. I think I'm going to the Moment though when it hits next month. Better screen, processor and keyboard will be doing it for me.
fixing any android stuck in fastboot
If your stuck in fast boot this is what you do.
1. Remove the micro sd card and somehow connect it to your computer.
2. Download a rom that is made for your phone and put it in a easily accessible folder on the micro sd.
3. Reinsert the sd card in the phone and reboot, once in fast boot go to hboot.
4. After going into hboot select recovery.
5. After this is done you must go to "install zip from sd card" and choose the rom that you have downloaded, select install and wait until the installation is complete, if unsuccessful redownload and try the whole process again, if unsuccessful the second time try downloading another rom.
If you have any questions please personal message me so i can help you.
Download: cyanogenmod.com
Btw i had a HTC hero and had this problem many times and this had worked every time.
I have a similar situation
when i power on the phone it goes straight to fastboot mode.
I Checked volume keys and are not stuck.
If I connect phone via usb and run:
fastboot reboot
the phone will load normally the android OS and will work just fine until you power it off again.
\
I dismantled the phone just to be sure there is no hardware issues, I tried to power on the phone without the home button connected to the board and the phone will load the android OS without any issue.
I dismantled the button itself, it has some sort of touch IC inside and a normal key button downside.
I could not notice any dust or water tracks in the button, so
at this point and dont know where to go...
I dont have another button just to be sure if it is the button itself or a board issue.
dbpaddler said:
So I just got done configuring chompSMS. Disabled notifications on the built in SMS app. Did a battery pull and got this screen and haven't been able to get out of it. Held down home & power and got a user memory wipe screen. Figure I'd give that a shot. Still stuck on the FASTBOOT screen and now have to redo the whole thing if I manage to get out of this screen.
Anyone else see this? Not much out there about Sprint's Hero, but there's a bit about Orange's Hero, rooting, flashing rom's and all that fun stuff. Nothing about getting it back to normal though.
and to add....after letting it sit connected to usb for a bit, the screen finally went dark but now won't turn back on. Really odd.
Click to expand...
Click to collapse
yurais said:
I have a similar situation
when i power on the phone it goes straight to fastboot mode.
I Checked volume keys and are not stuck.
If I connect phone via usb and run:
fastboot reboot
the phone will load normally the android OS and will work just fine until you power it off again.
\
I dismantled the phone just to be sure there is no hardware issues, I tried to power on the phone without the home button connected to the board and the phone will load the android OS without any issue.
I dismantled the button itself, it has some sort of touch IC inside and a normal key button downside.
I could not notice any dust or water tracks in the button, so
at this point and dont know where to go...
I dont have another button just to be sure if it is the button itself or a board issue.
Click to expand...
Click to collapse
People still use the Hero? There are so many better phones you can buy for dirt cheap. Heck, I got the Evo LTE for $80 on Craigslist. Even the Evo Shift, Design and 3D can be had cheap. I'd dump the Hero without blinking.
Hi. The phone application was not functioning well and the F/C dialog showed up. I powered off the phone and from that point, the phone won't turn on.
The battery was fully charged before this happened.
When I press the power button, the phone vibrates for half a second, the screen brightens up but does not show anything but a black screen.
I removed SIM and SD cards, removed the battery and performed the above steps but nothing happened.
I also tried to put on the charger to see what's going on. Once I plug the charger, the phone's screen brightens but shows only blank (even without pressing the power button)
When connected to the charger, the green light for charging is on for some minutes, then goes off automatically.
I tried to connect it to the PC, and PC Companion finds the device as usually. It even shows the dialog on the pc screen to mount the device.
I tried a hard reset, but does not work
On some point, the sony logo appeared and then a dialog saying: "sorry process system is not responding". The first time I pressed Force Close and the phone turned off. Immediately after that, the phone turned on and showed the exact message. I pressed "Wait" but nothing happened in the next 15 minutes.
I called Sony's support center and they suggested a software update. Did the process exactly as it should, but again, even after the software update the screen shows nothing but black. It is all the time brightened for some reason.
I tried to turn off the phone for some time by removing the battery, but as soon as I put the battery back on, the phone's screen brightens and stays that way forever.
The phone was functioning perfectly up until this issue. The only application I had installed apart from some games, was AWDLauncher. On the screen I had only a TASK widget and a battery status widget.
The phone is 3 months old and has been always in perfect condition.
ANY help would be appreciated!!!!
Many Thanks
Try to format phone with this method hope it should work as it seems the issue is with OS only ..
http://forum.xda-developers.com/showthread.php?t=717949
Many thanks for the prompt reply. I will try to do so and let you know how it goes!
o0k00l said:
Try to format phone with this method hope it should work as it seems the issue is with OS only ..
Click to expand...
Click to collapse
I tried the steps found in the link you gave me, but I couldn't go any further after step no (5) from the tutorial, as it would require to enable Debugging mode and I cannot access the OS (since the device won't turn on).
Is there a way to format all the contents of the device and have them replaced by running SEUS (as it always says that my device is up to date now)?
Was it this:
http://www.sonyericsson.com/cws/sup.../detailed/updateservice/xperiax10?cc=gb&lc=en
That Sony Ericsson told you to do?
If not, use that.
Download it, follow the steps when it says you have the latest version, press "Install Anyway".
Hope this works.
Hi itTim. thanks for the response
this is what i did but no improvement at all ((
Sounds like you broke your LCD screen somehow.
That would suck because I broke mine and it cost me $200 to fix.
Hi Hypercore.
Yes that could be the problem. The thing is that I always took rally good care of the phone, always carried in a leather pouch and never droped it. How sensitive is this lcd anyway?? Did you notice any cracks on your lcd or was the problem simillar to mine?
Thanks
When you turn on the phone does the lcd backlight turn on?
If so, look for any faint lines of color (usually a hairline size). If you see any of those then your screen is cracked.
the backlight is on, but there are no lines of colour on the lcd screen.
another weird thing is that the green light on the top blinks one or two times every time i put on the battery. even if the phone is off, once I insert the battery turns on automatically after a couple of seconds.
If all else fails you could try to flash back to your original fw with the tools here:
ht tp://forum.xda-developers.com/showthread.php?t=683793
AyDee said:
If all else fails you could try to flash back to your original fw with the tools here:
ht tp://forum.xda-developers.com/showthread.php?t=683793
Click to expand...
Click to collapse
That won't do anything.
I had almost the same issue. Nothing worked. But, when I removed the battery and left it for a day (24h) without it, it just started working again. Still working without issues..
Good luck!
Devtone said:
I had almost the same issue. Nothing worked. But, when I removed the battery and left it for a day (24h) without it, it just started working again. Still working without issues..
Good luck!
Click to expand...
Click to collapse
Phones are very wierd pieces of technology. I once bricked my k610i and that's a phone that's supposed to be impossible to un-brick, but out of nowhere a month or so later i picked it up, hit power and it turned on perfectly. Made no sense at all, but it worked.
Taking the battery out for a long time probably took all the electrical charges from it (kind of like how a computer power supply / monitor can hold power charges) and reset your handset.
Hypercore said:
Phones are very wierd pieces of technology. I once bricked my k610i and that's a phone that's supposed to be impossible to un-brick, but out of nowhere a month or so later i picked it up, hit power and it turned on perfectly. Made no sense at all, but it worked.
Taking the battery out for a long time probably took all the electrical charges from it (kind of like how a computer power supply / monitor can hold power charges) and reset your handset.
Click to expand...
Click to collapse
Indeed. It could be a frozen chip, memory fault, power-regulator and so on.
Hypercore said:
That won't do anything.
Click to expand...
Click to collapse
Ah, debug mode needed- I see now
tasaki said:
I tried the steps found in the link you gave me, but I couldn't go any further after step no (5) from the tutorial, as it would require to enable Debugging mode and I cannot access the OS (since the device won't turn on).
Is there a way to format all the contents of the device and have them replaced by running SEUS (as it always says that my device is up to date now)?
Click to expand...
Click to collapse
if you have done this and did not worked , then it is the LCD.
send it to workshop and check it there.
Guys i Really need the solve of this problem , my xperia has blank screen now without backlight and the phone completely doesn't work . when i put the battery and prees the switch botton it gives me 3 red signals , i've updated and hard reset but it didn't work , and btw the LCD is fine , any idea. did removing the battery worked???? . please answer
After a looooot of time since my latest post, finally my Xperia came back to life. There was a battery failure which means the phone was ok all the time. Weird thing is that the led light showed that the battery was charging ok. I removed the battery and after a lot of time it is working ok again. This was really really odd.
FYI for anyone else that gets this issue.
I just had this for the past hour after trying to change my baseband....could not get it back for anything.
What I did finally try was run another baseband via flash tool, connected to usb and it started flashing....after flash phone powered on again...yeah I agree with everyone, that is freaking scary when it happens.
Need some advice please
Any Flyer member who can advice me please?
Buyed a WIFI Flyer 16Gb Gingerbread stock no rooted turned on and suddenly turned off and got stuck in black screen (with some light in the back) vol down + power, nothing.
battery has 100% charge, but red led turned on and off ocasionally.
Any advice how to revive it would be greatly apreciated!
Thanks in advance,
Soft reset - Hold down power button only. Keep holding until tablet resets. You should know when this happens. You can't bring it up in bootloader/recovery (down vol. + power), until it's first actually turned off.
Does your PC recognize a device being plugged in when you connect
Sent from my HTC Flyer P510e using xda premium
.
Thanks for your replies:
It didnt work pressing only vol dow for a while, or presing only power button, it never rests.
Just behind power button a green mini led is turned on now all the time, probs started when removed back to insert sd card.
Tooked off to make some tests but now still nothing...
If connecting to PC nothing happens...not detected...no asking for install drivers
Any other advice?
Thanks in advance!
orb3000 said:
Thanks for your replies:
It didnt work pressing only vol dow for a while, or presing only power button, it never rests... probs started when removed back to insert sd card.
If connecting to PC nothing happens...not detected...no asking for install drivers
Any other advice?
Thanks in advance!
Click to expand...
Click to collapse
Take off back cover... Remove SD card... Try to reset again, power btn only, hold down 20 to 30 secs., don't use volume btn.
Nothing happens
i would suggest trying to globatron's attention. if anyone on this board would know what to do it would likely be him
orb3000 said:
Nothing happens
Click to expand...
Click to collapse
I would agree with mcord11758... Still...
orb3000 said:
battery has 100% charge, but red led turned on and off occasionally.
Click to expand...
Click to collapse
A red led isn't going to show with a 100% power condition. Later you wrote...
orb3000 said:
It didn't work pressing only vol down for a while, or pressing only power button, it never rests. Just behind power button a green mini led is turned on now all the time...
Click to expand...
Click to collapse
(doesn't make sense to me) A green led can't show unless the tablet is plugged into a power source and the battery actually is 100%...
If yours is a stock unit with a stock rom (and isn't defective), I would suspect a low battery condition that can't reset/reboot for lack of power...
Suggest you plug it into the wall and try the reset procedure again, and if still a failure, (maybe you can get some help from globatron or) call HTC.
...and then again, as I've read in other threads (that you've also seen), maybe all that's needed is a battery disconnect & reconnect. - Hope you get those pics, and if so... make it a last course of action, as you'll have no warranty if you do it.
Thanks.
Update:
I left computer connected to Flyer all night, and the day after it was turned off, then unplugged from PC and plugged it again, PC recognized the tablet and after that I ran the stock RUU, now it´s stuck on the process as it has been more than 20 minutes and progress bar in computer is at 100% with the following legend:
sending..........
updating the Rom image on your android phone
It is stuck there, how much should I wait? or if you recommend to do something else?
Thanks in advance for all your help.
UPDATE: RUU failed, says I have the wrong image, finished, exited and rebooted normally!
Now working, but I´m afraid to open the cover to insert my sd as the last time it was when it was turned off
Orb,
That sounds like it when into DL mode. On the flyer once you get out of DL mode it's normally fine after that. It seems to be random, mine did it once or twice, leedroid has seen it as have a few others.
After it boots again it goes back to normal.
Hi mate,
Thanks for your reply.
Very strange behavior. After all above mentioned I was able to use is perfect, even updated to OTA Honeycomb all went ok, installed some apps, etc.
Then decided it was time to test again to remove the cover and install my sd card, just in the minute I touched the back , not even finished of removing, and Flyer went screen off, now again I can´t turn it on. Could be a short circuit or something?
I will leave it connected to wall charger for the night and hopefully tomorrw will be able to turn it on again....
I swear never again to remove the back cover
PS: I checked battery level before all this and it was in 77%, now red led on power button is on...
globatron said:
Orb,
That sounds like it when into DL mode. On the flyer once you get out of DL mode it's normally fine after that. It seems to be random, mine did it once or twice, leedroid has seen it as have a few others.
After it boots again it goes back to normal.
Click to expand...
Click to collapse
orb3000 said:
Hi mate,
Thanks for your reply.
Very strange behavior. After all above mentioned I was able to use is perfect, even updated to OTA Honeycomb all went ok, installed some apps, etc.
Then decided it was time to test again to remove the cover and install my sd card, just in the minute I touched the back , not even finished of removing, and Flyer went screen off, now again I can´t turn it on. Could be a short circuit or something?
I will leave it connected to wall charger for the night and hopefully tomorrw will be able to turn it on again....
I swear never again to remove the back cover
PS: I checked battery level before all this and it was in 77%, now red led on power button is on...
Click to expand...
Click to collapse
That's weird, if it's not too much could you try and get a logcat (adb logcat) when its screen goes off while opening the cover. That should help us establish whether this is a HW problem(unique perhaps bad mainboard) or software problem (me,globatron,Lee, etc. experienced)
I can also confirm that it happened to me too couple of months back, but after soft reset it rebooted fine, but the backcover issue is new.
Sent from my HTC Flyer P510e using XDA Premium HD app
hello
Im orbs friend, my htc flyer still having the prob, everytime i touch the cover or pusih it by accident it goes back.
What I do is leaving it charging for awhile and press power button and vol down at the same time for around 30 sec for a couple of times and then it re start. Im guessing its not a software problem i dont find an explanation i even updated it to 2.3.4.
So my Prime is completely stock from an OS standpoint. Not rooted, just a handful of apps. I got the JB firmware notification this morning and I went ahead and kicked it off. Things seemed fine and the android with the blue progress bar popped up after a reboot. I left it alone and when I came back it was sitting on the ASUS boot screen. It has been on that boot screen ever since. I let it sit that way for over an hour and finally tried to power it off. I can power it off but it automatically tries to restart and gets stuck on the ASUS screen again. Tried holding the volume button down during power cycle and no luck. Anyone have any ideas?
Thanks
xRedLeadrx said:
So my Prime is completely stock from an OS standpoint. Not rooted, just a handful of apps. I got the JB firmware notification this morning and I went ahead and kicked it off. Things seemed fine and the android with the blue progress bar popped up after a reboot. I left it alone and when I came back it was sitting on the ASUS boot screen. It has been on that boot screen ever since. I let it sit that way for over an hour and finally tried to power it off. I can power it off but it automatically tries to restart and gets stuck on the ASUS screen again. Tried holding the volume button down during power cycle and no luck. Anyone have any ideas?
Thanks
Click to expand...
Click to collapse
Try the following and see if it helps.
Hold volume down and power button and when the text appears in top left just wait 5 seconds. When the icons appear on your screen use volume down to go to the wipe icon then press volume up.
Not guaranteeing this will work but it has for others.
If still broken come back and post.
I have a unlocked TF201 and managed to install cyanogen mod 10 on it. Then one fine day, it encountered the "turning on wifi" error, and I tried to be clever and did a format /data on CWM.
Now I have a TF201 which can enter CWM (but can't install anything because it can't read SD card) and can get into Fastboot (since it's unlocked), but can't seem to be detected when i run fastboot from my win-pc.
Can anyone help? I tried installing various of the ADB fastboot drivers, in particular the universal naked driver from another thread, but still can't seem to work!
Can help? Pls?
fonsus said:
I have a unlocked TF201 and managed to install cyanogen mod 10 on it. Then one fine day, it encountered the "turning on wifi" error, and I tried to be clever and did a format /data on CWM.
Now I have a TF201 which can enter CWM (but can't install anything because it can't read SD card) and can get into Fastboot (since it's unlocked), but can't seem to be detected when i run fastboot from my win-pc.
Can anyone help? I tried installing various of the ADB fastboot drivers, in particular the universal naked driver from another thread, but still can't seem to work!
Can help? Pls?
Click to expand...
Click to collapse
adb and fastboot are different things.
adb you will be able to use while in CWM and fastboot you can use while in fastboot.
You need to be able to push a rom onto your device thru adb while in cwm.
There could be a few things wrong. It could be a faulty cable or it could be that your usb ports on the computer don't like it.
Have you tried using usb ports on the back of your computer and seeing if anything shows up in device manager when you are in cwm?
If not can you try it on another computers usb ports and see if anything shows up in device manager when you are in cwm?
Please come back with a bit more information when you have tried this. Once you can see the device in device manager you should be able to install the naked drivers and I can help you from there.
edit.. can you please also tell me what happens when you just try to let it boot.. where does it get stuck, what is on the screen?
flumpster said:
Try the following and see if it helps.
Hold volume down and power button and when the text appears in top left just wait 5 seconds. When the icons appear on your screen use volume down to go to the wipe icon then press volume up.
Not guaranteeing this will work but it has for others.
If still broken come back and post.
Click to expand...
Click to collapse
I also have this exact same problem. For mine, I can't get it to show the text or get to this menu (I've definitely gotten there before this, though).
klarh said:
I also have this exact same problem. For mine, I can't get it to show the text or get to this menu (I've definitely gotten there before this, though).
Click to expand...
Click to collapse
I'm having this problem. No bootloader messages show just splash screen. I get a blank screen when I hold power and volume up but that's it. ****.
T-HO6969 said:
I'm having this problem. No bootloader messages show just splash screen. I get a blank screen when I hold power and volume up but that's it. ****.
Click to expand...
Click to collapse
Its power and volume down to get to the wipe icon not power up.
flumpster said:
Try the following and see if it helps.
Hold volume down and power button and when the text appears in top left just wait 5 seconds. When the icons appear on your screen use volume down to go to the wipe icon then press volume up.
Not guaranteeing this will work but it has for others.
If still broken come back and post.
Click to expand...
Click to collapse
Thanks for the response. vol down and power don't do me any good. It won't let me into the stock recovery mode. I've been down that road before and entered it successfully so I'm pretty certain I'm doing it right. It just loops me back to the ASUS screen.
Thanks again.
xRedLeadrx said:
Thanks for the response. vol down and power don't do me any good. It won't let me into the stock recovery mode. I've been down that road before and entered it successfully so I'm pretty certain I'm doing it right. It just loops me back to the ASUS screen.
Thanks again.
Click to expand...
Click to collapse
The only way to do it is to have it powered off. Then hold the volume down button first and while holding it start holding power button also.. Then don't let go of both buttons until it appears.
If that don't work I'm not sure what you have done sorry mate.
flumpster said:
The only way to do it is to have it powered off. Then hold the volume down button first and while holding it start holding power button also.. Then don't let go of both buttons until it appears.
If that don't work I'm not sure what you have done sorry mate.
Click to expand...
Click to collapse
I guess I'm looking at an RMA then because it is powered off when I do the vol down + power. Still only get the splash screen. I wouldn't be upset if I was trying to load a custom ROM or something but all I did was let the blasted thing try to install the OTA. Oh well, thanks again for your time.
xRedLeadrx said:
I guess I'm looking at an RMA then because it is powered off when I do the vol down + power. Still only get the splash screen. I wouldn't be upset if I was trying to load a custom ROM or something but all I did was let the blasted thing try to install the OTA. Oh well, thanks again for your time.
Click to expand...
Click to collapse
After communicating the issue to support, they said to do an RMA. This is my second RMA for this device, which is pretty annoying.
klarh said:
After communicating the issue to support, they said to do an RMA. This is my second RMA for this device, which is pretty annoying.
Click to expand...
Click to collapse
I think there must be some serious issues with TF201 and JB. I have got into exactly the same position by trying to use Protato's method to update to WW JB - and so have at least 3 others. But if the genuine update is doing this too!!
I'm going to request RMA. My tablet has gone to hell and this is just the seal of approval. Have a feeling I'm Infinity bound now. Good luck to all.
I am definitely going to have to RMA at this point. 3rd for me. Mine started off with the wonderful Serial Number unknown and was then suffering from pretty bad wifi/bluetooth fallout. ASUS has made good by me on both cases so far and I felt pretty good about my Prime but I must say I'm a bit disappointed that I need a 3rd RMA. I'll be happy overall if they get it back to me in good working order in a timely fashion.
xRedLeadrx said:
I am definitely going to have to RMA at this point. 3rd for me. Mine started off with the wonderful Serial Number unknown and was then suffering from pretty bad wifi/bluetooth fallout. ASUS has made good by me on both cases so far and I felt pretty good about my Prime but I must say I'm a bit disappointed that I need a 3rd RMA. I'll be happy overall if they get it back to me in good working order in a timely fashion.
Click to expand...
Click to collapse
How long foes RMA take for you usuallly? I was an idiot before to an opened up my Prime. I didn't mess with it just peaked to assembly if my camera fell out. Think this will matter? Do we have to pay the shipping?
My Mi Pad 2 is fully bricked, is there any solution?
this is what happend, I install LineageOS on it and it was fine, but then I wanted to change the recovery, then the OS wont boot so I try to put the old recovery in it, it also fails, so I tried to put windows on it, by booting an USB pendrive and mouse with an OTG cable when it start, but a signal of battery error appears, and now it wont boot at all. If I connect the tablet to the wall power, it shows me 0% loading, I left it for like 2 or 3 days connected and nothing, still 0%, when I try to power on the tablet, it shows me the battery icon with a warning sign /!\ and wont show me the "Mi" logo, just direct to the warning sign.
The pc wont recognize it either, and wont work any buttons combination, is there any solution?
This might be over 2 years late for you but the same thing happened to me and I thought i'd post the fix incase anyone else comes across this thread.
[FIX] Open the backing and simply untether the battery ribbon cable, im not sure if leaving it unplugged cleared any held memory so I left it for a good minute or so before reconnecting. Screw it all back together, turn it on, should work fine
sk3iron said:
This might be over 2 years late for you but the same thing happened to me and I thought i'd post the fix incase anyone else comes across this thread.
[FIX] Open the backing and simply untether the battery ribbon cable, im not sure if leaving it unplugged cleared any held memory so I left it for a good minute or so before reconnecting. Screw it all back together, turn it on, should work fine
Click to expand...
Click to collapse
Can you please describe the process of opening the back cover?
Thank you
Hannah
hannah187 said:
Can you please describe the process of opening the back cover?
Thank you
Hannah
Click to expand...
Click to collapse
remove the 2 screws at the bottom (they're torx t3? I think. a good set of precision screwdriver bits should have it) and use ideally plastic spudgers to spudge it out. its clipped in but it's really easy to remove. the back panel comes off by itself, and the rest of the tablet is self contained in a magnesium frame attached to the screen.
i was pretty impressed by the construction really. super solid!
So... I had the Mi pad 2 laying in my house running on MIUI 9 and one day I got curious and tried to unlock its bootloader.
I didn't remember my password and the recovery phone no. is discontinued now. and I couldn't change it or sign out.
So like an idiot, I factory reset it. And now it's asking for a password for the last mi id.
can anyone help me? Will and edl flash do the work?
THANKS
Ved0704 said:
So... I had the Mi pad 2 laying in my house running on MIUI 9 and one day I got curious and tried to unlock its bootloader.
I didn't remember my password and the recovery phone no. is discontinued now. and I couldn't change it or sign out.
So like an idiot, I factory reset it. And now it's asking for a password for the last mi id.
can anyone help me? Will and edl flash do the work?
THANKS
Click to expand...
Click to collapse
Just reinstall it like a PC