I recently tried to flash the OLYFR_U4_1.8.3 SBF from this thread:
http://forum.xda-developers.com/showthread.php?t=1125944
this failed, and now my phone is stuck on the moto red screen. I have tried to get it back into RSD mode, using the volume up while the phone was off and it will not anymore. i also cannot get it into fastboot mode. please helps. thanks.
geishroy said:
I recently tried to flash the OLYFR_U4_1.8.3 SBF from this thread:
http://forum.xda-developers.com/showthread.php?t=1125944
this failed, and now my phone is stuck on the moto red screen. I have tried to get it back into RSD mode, using the volume up while the phone was off and it will not anymore. i also cannot get it into fastboot mode. please helps. thanks.
Click to expand...
Click to collapse
Did you flash the service or full sbf?
What did you flash over? i.e. 4.1.26, 4.1.52, 4.1.57?
Was your phone fully charged when you flashed?
Related
I was on eclipse 5. I wanted to update to v6 so I got an gingerbread SBF file and used rsd lite to flash it. Now I get bootloop. :/
TransX2 said:
I was on eclipse 5. I wanted to update to v6 so I got an gingerbread SBF file and used rsd lite to flash it. Now I get bootloop. :/
Click to expand...
Click to collapse
Boot into stock recovery and do a factory reset.
Sent from my DROID X2 using Tapatalk
post above, he is correct just boot into the android recovery and factory reset it should boot up after that
TransX2 said:
I was on eclipse 5. I wanted to update to v6 so I got an gingerbread SBF file and used rsd lite to flash it. Now I get bootloop. :/
Click to expand...
Click to collapse
For future reference, you didn't need to SBF between - totally unnecessary. Wipe data/cache and install.
Sent from my DROID X2 using xda premium
When one hold the power and both volumes down, before reboot, the motorola symbol comes up with "starting RSD protocol support" above it. what is that? I have bricked my phone while attempting flash a theme. I went into bootstrap recovery and was able to do a factory reset, but unfortunately it didn't work and the phone wull not reboot, nor will it connect through usb to the pc. HELP
I may be wrong but you might have to SBF back to stock. There is a how to in the development thread I believe.. but be calm, it is fixable.
I just tried to flash Artics old rom but when i'm rebooting, the screen just get black. So i tried to restore the rom with my Nandroid backup, but I get the same problem, just a black screen.
What am I going to do?
I have Safesystem enabled (using Safestrap)
Tried to flash FTS instead but now the phone is stuck in a bootloop.
baxtex said:
I just tried to flash Artics old rom but when i'm rebooting, the screen just get black. So i tried to restore the rom with my Nandroid backup, but I get the same problem, just a black screen.
What am I going to do?
I have Safesystem enabled (using Safestrap)
Tried to flash FTS instead but now the phone is stuck in a bootloop.
Click to expand...
Click to collapse
reflash original RSD ROM with RSD lite...
this method dont fail...
if necessary send me mp...
hacker
Whole lotta development here!
Are the mods on vacation?
We do not read each and every post made as that is impossible. We however work when someone reports it . @OP see this. Moved to Q&A
hacker812c said:
reflash original RSD ROM with RSD lite...
this method dont fail...
if necessary send me mp...
hacker
Click to expand...
Click to collapse
Yeah I know, but I can just turn the phone off holding down the power button and volume down button, then going into safestrap and disable safe boot then I can use stock rom again. So the stock is working, but not any other custom rom.
Nobody?
Mobile IP registration error 67
OK heres my situation. Last night right before work I flashed jokers jb cm10 rom over a factory reset of cm7 and all was good, except google play kept trying to download random things in my pocket and heating up while I worked. As a reflex I turned on airplane mode to cool it down and save battery. And just like that I had absolutely no data whatsoever. I tried reflshing cm10. Nothing. I tried the data fix. Nothing. I flashed peetrs v4, twice. Nothing. I had to wait my whole shift to get home to sbf this thing to new. I went on the compendium and downloaded 1FF-sunfire-user-2.3.4-4.5.1A-1_SUN_198_7-CM-release-keys-signed-Sprint-US.zip. I installed the drivers unzipped the sbf and opened rsd-lite and waited for it to connect. When I flashed it everything went smoothly until it said manually power on the device. It did not boot for 5 mins. I then went on a stupid flashing frenzy. I flashed derpunlock then I flashed the 198_7 radio and it wouldnt boot. In my final act of noobishness I flashed peetrs unlocktwrp sbf . Now it will instantly power off when I boot it with vol- and if I boot it with usb attached it will go into rsd mode. This rsd mode is semu functional. It begins to flash but gets gets stuck on switching modes (i can manually switch by doing a battery pull) and bp passthrough is stuck on 0. I can get into fastboot if I hold volume+ while booting. Any help is greatly appreciated (unless it involves permalocking my bootloader).
Sent from my Nexus 7 using Tapatalk 2
Hmm, I am trying to understand your situation, but it's not easy.
Did you wipe data after flashing full 198_7 sbf?
This all thing after that full sbf flashing, looks to me more like some usb problem or what? Did you try different computer?
Do you have failed to boot 3 now?
If you flashed that unlock sbf with twrp, you should go directly in recovery and wipe data and you can try to flash some other rom.
I was unable to boot after 198_7 so I was not able to wipe data. I tried different usb ports, does the same thing. It says failed to boot 3 now. How do I get into recovery as the menu at boot is not available (screen shuts off as I try to scroll through the options) fastboot and rsd kinda work.
Sent from my Nexus 7 using Tapatalk 2
So try to flash full 198_7 sbf and write me, how it goes.
1st screen
SVF : 108:1:2
Failed to boot 3
Starting RSD mode
Flashing now
Now says
SVF : 108:1:2
Failed to boot 3
Starting RSD mode
SVF : 106:1:2
sec_exception: b655, exec, eb
I then powered it off to save battery as im sure its not charging
I saw this posthttp://forum.xda-developers.com/showthread.php?p=29585149 in another similar thread, how do I use fastboot to flash jokers v4 recovery?
Sent from my Nexus 7 using Tapatalk 2
Hmm, why failed to boot 3?
Could you try to decompile 198_7 sbf with sbf codec and try to flash stock recovery (CG58) with fastboot? Do not unlock yet.
peetr_ said:
Hmm, why failed to boot 3?
Could you try to decompile 198_7 sbf with sbf codec and try to flash stock recovery (CG58) with fastboot? Do not unlock yet.
Click to expand...
Click to collapse
I do not know how to flash with fastboot. I have to go to work all night so I cannot try until tomorrow. Thank you for all your help thus far.
Sent from my Nexus 7 using Tapatalk 2
Ok. When you will have some time, try to get familiar with the fastboot and decompiling sbf. There are some readings over here. Could you? Everything will be much easier to test then.
Ok I was finally able to decompile the sbf and I succesfully flashed the stock recovery
Good. Really.
And what's the status of your phone?
same as before still not booting, the fastboot cmd message said
sending 'recovery' (8192 KB)... OKAY ( 1.126s )
writing 'recovery' ... OKAY ( 0.954s )
so I assumed it was successful.
Yes it most probably was successful.
Are you absolutely sure, that you didn't flash any sv2 file?
Try to flash boot.img from the decompiled sbf.
I just looked in my downloads folder and to my horror I see 2.3.5sv2_198_7_radio.sbf
Would that have permalocked my bootloader?
Hmm, why am I writing that big red warning there?!
Yes. Your bootloader is permanently locked!
Oh, oh, oh.
No problem to unbrick that, but it's locked.
damn, all i wanted was to flash the radio. in my haste i must have ignored the warning assuming radios had nothing to do with bootloaders. Im gonna miss your hybrid rom
Oh well, this is why I have a Nexus 7.
should i follow this guide?
http://forum.xda-developers.com/showthread.php?t=1797787
Ok, let's forget this BIG mistake.
Actually I have locked version of my rom now.
If you are familiar enough with decompiling, I would suggest something different for you.
Recompiling USC_19 sbf only with boot.img, recovery.img, cdrom and system just to make it quickly reflashable.
Do you think that you can make it?
Or I will make it, but this would take long. (bad uploading speed)
is that the same thing in your thread (http://forum.xda-developers.com/showthread.php?t=1798145) under "others"
Yes, except, that one is not containing system, but as I think about it, you should have 198_7 system installed right now, so it should boot after flashing this boot, recovery and cdrom sbf. Or you will have failed to boot 4, then you will have to make the same sbf with USC_19 system. Don't forget to wipe data.
now the battery finally got too low to flash, so I have to do the usb trick to charge it. will try again in an hour or so
Ok.
Hey, yesterday I try to change firmware on Motorola XT910 with Safestrap , but I have not succeed. I disabled safestrap and I went into recovery mode, I use wipe data / factory reset, after I gave reboot.All ok so far, appears Motorola logo, and after the screen make black, but does not close the phone. I can fix it?
KanYST said:
Hey, yesterday I try to change firmware on Motorola XT910 with Safestrap , but I have not succeed. I disabled safestrap and I went into recovery mode, I use wipe data / factory reset, after I gave reboot.All ok so far, appears Motorola logo, and after the screen make black, but does not close the phone. I can fix it?
Click to expand...
Click to collapse
Yes.
Custom recoveries can't flash firmware, only ROM's. You need RSD lite to flash firmware. Make sure you have the correct firmware for your region, Download RSD lite, read/watch some tutorials to learn how to use it, and you will be golden.
Draxin said:
Yes.
Custom recoveries can't flash firmware, only ROM's. You need RSD lite to flash firmware. Make sure you have the correct firmware for your region, Download RSD lite, read/watch some tutorials to learn how to use it, and you will be golden.
Click to expand...
Click to collapse
Thx a lot, I succeed xD
I was running fine with BMM. Then I decided to switch to SafeStrap and installed it through the apk. Later I wanted to get back to BMM so I uninstalled safestrap, and just out of curiosity I rebooted it to check if it still starts without the recovery. It didn't. I tried flashing the stock rom through RSD. I had erased my CID a while back. Now the firmware I flashed through RSD, I was unsure which to flash. I tried flashing these firmwares:
9.8.2O-124_SPUEM-14_S7_USASPDRICS01VFGE1007.0R_USASPDRJBRTVFDE_P011 _A011_p2b_S1FF_fb_CFC.xml
9.8.2O-124_SPUEM-14_S7_USASPDRICS01TMOGE1007.0R_USASPDRJBTMDE_P011_ A019_p2b_S1FF_fb_CFC.xml
9.8.2O-124_SPUEM-14_S7_USASPDRICS01RUKE1007.0R_USASPDRJBRTGB_P011_b57374ab5a_p2b_S1FF_fb_CFC.xml
I live in India. Both are jellybean firmwares. I read somewhere that asian users can flash eu firmwares. So I went ahead and flashed but none of those boots my phone. I get Motorola logo and then blank screen. I'm using RSD Lite 6.1.6. Can somebody guide me as to which firmware should I flash? I'm having panic attacks since last night... :-|
EDIT: Fixed by booting to BP Tools from the bootloader. This is what happens when your cid is erased. Thank you XDA :victory:
shreyas.kukde said:
I was running fine with BMM. Then I decided to switch to SafeStrap and installed it through the apk. Later I wanted to get back to BMM so I uninstalled safestrap, and just out of curiosity I rebooted it to check if it still starts without the recovery. It didn't. I tried flashing the stock rom through RSD. I had erased my CID a while back. Now the firmware I flashed through RSD, I was unsure which to flash. I tried flashing these firmwares:
9.8.2O-124_SPUEM-14_S7_USASPDRICS01VFGE1007.0R_USASPDRJBRTVFDE_P011 _A011_p2b_S1FF_fb_CFC.xml
9.8.2O-124_SPUEM-14_S7_USASPDRICS01TMOGE1007.0R_USASPDRJBTMDE_P011_ A019_p2b_S1FF_fb_CFC.xml
9.8.2O-124_SPUEM-14_S7_USASPDRICS01RUKE1007.0R_USASPDRJBRTGB_P011_b57374ab5a_p2b_S1FF_fb_CFC.xml
I live in India. Both are jellybean firmwares. I read somewhere that asian users can flash eu firmwares. So I went ahead and flashed but none of those boots my phone. I get Motorola logo and then blank screen. I'm using RSD Lite 6.1.6. Can somebody guide me as to which firmware should I flash? I'm having panic attacks since last night... :-|
Click to expand...
Click to collapse
Try this:
Get into fastboot mode,select "recovery",when android lying on his back with a red triangle appears,press vol- and vol+ and select "factory data reset" option.
Sent from my Razr XT910
Try the one..
Blur_Version.982.124.14.XT910.Vodafone.en.EU
Find it on SBF Droid, it should be under Vodafone Germany..
From the E
welder73 said:
Try this:
Get into fastboot mode,select "recovery",when android lying on his back with a red triangle appears,press vol- and vol+ and select "factory data reset" option.
Sent from my Razr XT910
Click to expand...
Click to collapse
I had tried factory reset. It didnt work. I had to boot to BP Tools to boot the phone. When your CID is erased, this happens, reported people on XDA. Thank you for the suggestion anyway