Hi, so i have made the jig well sort of.
I sliced open a micro usb cable that i had, and well i can not for the life of me find the 4/5 pins, i actually do not think my micro usb has them. :/
I have attached photos, if someone could please take a look and let me know what i should be doing, whether to get rid of the small green circuit board (and how) or if this is the incorrect micro usb cable.
I need it reset in the next 6 hours, T-Mobile arriving in the morning to take my old S2 and give me a full kit replacement.
HELP PLEASE
Thank You
Dint u say the same thing yesterday. how many times are they going to come and raid ur house ???
http://forum.xda-developers.com/showthread.php?p=15960704
Related
Guys, I'm convinced the usb connector on my 9 month old TP is defective and gets worse each time I use it. I had bought a touchstone charger to ease the connector wear but still, I was eventually having problems with USB data connectivity using store bought cables. I even sent my TP in to fix the connector and when I got it back, still no USB connectivity. Just a completely wiped TP. So HP sent me one of their "genuine" silver dot cables and low and behold it worked fine. (My original cable was lost)
Now, months later, I'm having problems with the USB data connection again. I either get the "Not enough current message" in WebOS or no MTP USB symbol in CM9. Sometimes the PC will chime positively but with an error message (can't detect device). I received another genuine HP cable and it behaves the same as the other one. Inserting them normally, they appear to be in tight, the PC will chime but Windows will say that there's a problem, can't detect device. The only way to get it to work is to insert the microusb side at a 45 degree angle tilted downward and hold it in for 5 seconds, then (ever so slowly) release the pressure to the connector. 50% of the time I'll get a Windows message that says the USB is degraded and run slower than normal (which I think means it thinks its in USB1.1 slow xfer mode) and 50% it works fine at USB 2.0 (until I pull the cable out of the connector). I also have 2 store bought cables that won't ever successfully connect to USB with the TP but work fine with my Samsung cell in both charging and xferring music over to the phone.
So what I'm getting at here is that no standard microusb cable is the same and that there must be something special about the HP genuine one. Do these cables have a resistor on pin 4 ID tied to GND pin 5? Even so, I think what is wearing the most is pins 1 & 2 and maybe 3 (VCC and the data pins) which is why it may only work by concentrating on seating those pins first. Does it make sense that the 'can't detect device' message comes up with just the data lines and ground connected but no VCC? For that matter, why would the battery symbol in CM9 always show the lightning bolt assuming pin 1 VCC is not connected?
I'd appreciate any responses from other members here since I believe without USB the TP could be bricked in case some boot code gets corrupt and you are forced into WebOS recovery mode. This has never happened to me yet and I've installed a lot of nightlies but it COULD happen, no guarantees. What is inevitable is my connector will eventually wear out and my TP will only live until the bootloader DOES get corrupt, hopefully later than sooner. This could be the case with all TP's. Just imagine if in a couple of years everyone's TP's USB port goes bad. Sounds like the devs should figure out a way to fix a bricked TP wirelessly, if that's at all possible.
Thanks,
synchron
One of my Touchpad's had the same problem in Webos it said using wrong charger may not charge or something similar and with Android ie nightly the charging signal came up but it did not charge.
I spoke to HP and pointed out that I have 2 Tablets and that swapping leads or chargers made no difference all combinations worked on one but not the other.
They agreed to fix it and replaced the part. It is now working fine. And as with yours my computer failed to recognize the tablet properly.19 times out of 20 on the one time it did I was able to back up and remove Android before HP picked it up.
I would send it back under warranty or if that has expired state that it was preexisting. Otherwise as you said it is going to become pretty much unusable.
Don't let them fob you off.
Good luck
spaceosc said:
if u bought it during the fire sale u have about a week till (8/20) the one year warranty expires.
http://kb.hpwebos.com/wps/portal/kb/na/touchpad/touchpad/wifi/supportservices/page_en.html
go to palm support and CHAT with them. do not call cuz that cost money.
once u get an RMA they will send a box and take care of Shipping.
then go here to wipe and remove android
http://forum.xda-developers.com/showthread.php?t=1426244
once wiped send it in and your speaker will be fixed, it will take about a week.
Click to expand...
Click to collapse
from another thread
sstar said:
One of my Touchpad's had the same problem in Webos it said using wrong charger may not charge or something similar and with Android ie nightly the charging signal came up but it did not charge.
I spoke to HP and pointed out that I have 2 Tablets and that swapping leads or chargers made no difference all combinations worked on one but not the other.
They agreed to fix it and replaced the part. It is now working fine. And as with yours my computer failed to recognize the tablet properly.19 times out of 20 on the one time it did I was able to back up and remove Android before HP picked it up.
I would send it back under warranty or if that has expired state that it was preexisting. Otherwise as you said it is going to become pretty much unusable.
Don't let them fob you off.
Good luck
Click to expand...
Click to collapse
spaceosc said:
from another thread
Click to expand...
Click to collapse
Thanx for your prompt responses. I bought my TP at the 2nd fire sale through BB in early Nov so I still got a few more months but I would rather wait a bit more since they did nothing the 1st time around. I think the connector is on some daughter board along with the vibrate device which is soldered to the main board. Doesn't sound like a big deal to repair it. Still, what makes the HP cable different then the others? Are there known cables I can get online that might be made better to always work and make better contact than the HP ones?
Synchron
synchron50 said:
Thanx for your prompt responses. I bought my TP at the 2nd fire sale through BB in early Nov so I still got a few more months but I would rather wait a bit more since they did nothing the 1st time around. I think the connector is on some daughter board along with the vibrate device which is soldered to the main board. Doesn't sound like a big deal to repair it. Still, what makes the HP cable different then the others? Are there known cables I can get online that might be made better to always work and make better contact than the HP ones?
Synchron
Click to expand...
Click to collapse
dont wait, ive sent my TP in 3 times, 1st time for charging port, 2nd for a crack around the speaker, 3rd for a busted speaker.
spaceosc said:
dont wait, ive sent my TP in 3 times, 1st time for charging port, 2nd for a crack around the speaker, 3rd for a busted speaker.
Click to expand...
Click to collapse
Thanks for your advice. Did they fix everything that was intended? Was turn around time no longer than 2 weeks for each repair? When was your last repair (busted speaker) done? Is your serial number the same or did you ever get a replacement (meaning a refurbished one) back?
Thanks
synchron50 said:
Thanks for your advice. Did they fix everything that was intended? Was turn around time no longer than 2 weeks for each repair? When was your last repair (busted speaker) done? Is your serial number the same or did you ever get a replacement (meaning a refurbished one) back?
Thanks
Click to expand...
Click to collapse
i keep track of the serials and they always came back the same. i have more than one pad and i asked for one to be replaced completely. we will see if that happens. but they fix only what u ask for and nothing else.
it can take longer depending on Weekends. takes 2 days to get your box, then 2 days to get it to HP, then 3- 4 days to get your fixed unit. its all done thru UPS, cant send it out on the weekends or receive it
spaceosc said:
i keep track of the serials and they always came back the same. i have more than one pad and i asked for one to be replaced completely. we will see if that happens. but they fix only what u ask for and nothing else.
it can take longer depending on Weekends. takes 2 days to get your box, then 2 days to get it to HP, then 3- 4 days to get your fixed unit. its all done thru UPS, cant send it out on the weekends or receive it
Click to expand...
Click to collapse
Thanks, you are giving me hope to try again while my warranty is still good. Maybe I'll put a big note on the screen PLEASE REPLACE USB CONNECTOR - wouldn't hurt.
Synchron50
I know this is really old, but im finding my self with similar issues and no warrenty
synchron50 said:
Guys, I'm convinced the usb connector on my 9 month old TP is defective and gets worse each time I use it. I had bought a touchstone charger to ease the connector wear but still, I was eventually having problems with USB data connectivity using store bought cables. I even sent my TP in to fix the connector and when I got it back, still no USB connectivity. Just a completely wiped TP. So HP sent me one of their "genuine" silver dot cables and low and behold it worked fine. (My original cable was lost)
Now, months later, I'm having problems with the USB data connection again. I either get the "Not enough current message" in WebOS or no MTP USB symbol in CM9. Sometimes the PC will chime positively but with an error message (can't detect device). I received another genuine HP cable and it behaves the same as the other one. Inserting them normally, they appear to be in tight, the PC will chime but Windows will say that there's a problem, can't detect device. The only way to get it to work is to insert the microusb side at a 45 degree angle tilted downward and hold it in for 5 seconds, then (ever so slowly) release the pressure to the connector. 50% of the time I'll get a Windows message that says the USB is degraded and run slower than normal (which I think means it thinks its in USB1.1 slow xfer mode) and 50% it works fine at USB 2.0 (until I pull the cable out of the connector). I also have 2 store bought cables that won't ever successfully connect to USB with the TP but work fine with my Samsung cell in both charging and xferring music over to the phone.
So what I'm getting at here is that no standard microusb cable is the same and that there must be something special about the HP genuine one. Do these cables have a resistor on pin 4 ID tied to GND pin 5? Even so, I think what is wearing the most is pins 1 & 2 and maybe 3 (VCC and the data pins) which is why it may only work by concentrating on seating those pins first. Does it make sense that the 'can't detect device' message comes up with just the data lines and ground connected but no VCC? For that matter, why would the battery symbol in CM9 always show the lightning bolt assuming pin 1 VCC is not connected?
I'd appreciate any responses from other members here since I believe without USB the TP could be bricked in case some boot code gets corrupt and you are forced into WebOS recovery mode. This has never happened to me yet and I've installed a lot of nightlies but it COULD happen, no guarantees. What is inevitable is my connector will eventually wear out and my TP will only live until the bootloader DOES get corrupt, hopefully later than sooner. This could be the case with all TP's. Just imagine if in a couple of years everyone's TP's USB port goes bad. Sounds like the devs should figure out a way to fix a bricked TP wirelessly, if that's at all possible.
Thanks,
synchron
Click to expand...
Click to collapse
Hi all. I know this thread is really old, but I'm finding myself dealing with similar issues. And I'm obviously out of warranty. I can't get windows, linux, or Toolbox to pick up the USB. I'm actually in a worse case scenario mention here and am stuck in meboot, TWRP, and WebOS recovery, because I had wiped the rom. It must be an issue with the USB port, I've lost track of my original Hp touchpad OEM cable, and have tried every USB cable I can find. Any help would be appreciated.
Somehow the micro usb port on the phone (the charger) has been mashed up inside, i think it may have been due to someone trying to fit the wrong charger into it.
a shop said it'd have to get sent away,
i was wondering if their is a place to send it to get fixed or it it fixable ?
atm im having to charge another battery with a docking station and swap battery's because it wont charge,
it did work a little earlier on today, charging. but i can see the insides are pretty well destroyed.
it looks like the piece can be removed and a new one soldered on,
any ideas ?
thanks.
Honestly, if somone on here knows how to fix hardware issues I am sure they can lend you a hand but otherwise you will have to go to a repair shop and have it serviced. Just make sure that everything is complete stock and bootloader is in locked state just to be safe. If you don't want to send it back through the mail you can always take to a sprint authorized repair shop.
If you want to attempt it yourself here you go
http://www.youtube.com/watch?v=jxiv3x88eRg
http://www.youtube.com/watch?v=fdxrPWrVgR8
http://www.youtube.com/watch?v=I-HlZQKQzoQ
http://www.ebay.co.uk/itm/New-HTC-E...K_Replacement_Parts_Tools&hash=item20ca337adf
Thanks guys, ive been looking online and some places seem to say they can fix it,
that video is just jokes, he faffs around with the thing im sure he ha no idea what hes doing.
ive found usb ports for other htc models just not the evo 3d.
ive realised it is quite a common problem
its charging via my docking station... just. obviously the internals of the micro usb are mashed up, and i know the replacement needs to be soldered on,
ive looked on some websites but cannot find anywhere to fix it.
its ok atm as its charging via dock, and i have a spare battery, also i can just take out my sd card to add stuff but it i rather annoying abd id like it fixed asap.
You could always use WiFi file explorer,of course WiFi is required but you can read and write the sdcard from your ip address,
Signature (Don't ask me for help, couldn't careless if your phone explodes)
strange thing is its connecting via my dock.. and charging, eventho the insides of the micro usb are mashed up..
it wont work with any other cable just in the dock...
im guessing the dock pin is slightly larger thus allowing a connection ?
Hi xda.
I cant charge my phone. I made tests with 3 original micro usb cable, and got nothing(wall and usb).
I got no led, no sounds when i plug it.
So, I tried with a universal charger for batteries, and it works. So i guess my battery is fine.
Apparently my problem is the micro usb port. I do not have warranty.
Despite having no experience with maintenance, I found a video on youtube and did not seem very difficult to replace. So i searched and found on ebay a new micro usb port, for a very low price.
What you guys suggest?
Lead to assistance and wait 15 days or more, and spend more money...
Or buy at ebay and try to change myself?
Theres a way to find if my problem is really on my micro usb port?
This could be another problem?
Thanks.
sorry for my bad english.
http://www.youtube.com/watch?v=eo93EF7rVIw
first try to clean usb port for dirt if it does not work
disassemble your phone as shown in the video. check usb connections etc. if none solves try to find the right part on ebay and replace it.
or if you say i cant do that simple give it to samsung service and get it repaired with money
Hey all,
I thought my USB port was broken given that it didn't charge and I couldn't connect it to the PC.
So I bought a nice one and replaced it.... no dice. Still doesn't work. However, the odd thing is, I also bought a USB jig and that does work. Anyone got any clue what could be going on?
Cheers
Maybe the wrong USB board, there's a couple of different ones, best way to work it out is match up with the one already in the phone. Search for similar threads in Q&A over the past few mths; there's been detailed discussions (and pics from memory) of which board is which.
Check on this thread.....
http://forum.xda-developers.com/showthread.php?t=2335961
it might help.......
Sent from my rooted, de bloated, stock JB powered S2 via PhilZ kernel and XDA developers app
USB Connectivity Problem
mirey said:
Hey all,
I thought my USB port was broken given that it didn't charge and I couldn't connect it to the PC.
So I bought a nice one and replaced it.... no dice. Still doesn't work. However, the odd thing is, I also bought a USB jig and that does work. Anyone got any clue what could be going on?
Cheers
Click to expand...
Click to collapse
As you said that even after replacing the port.... it didnt work. And it worked out after you connected it to your new USB jig. This means that there might be a problem with the original USB wire which comes with phone when you Buy it. It might even be a problem with the Connectivity Board in the phone as it must have been damaged. I'm not really sure about this but it might even be a problem with software... Maybe you should have tried to atleast wipe the whole system... maybe then you would get to know more about the problem.
Cheers
heh, yeah, I did check that and ordered a 2.2, but they sent me a 2.3.
However, I stuck my old 2.2 one back in, and tried it with the jig, and the jig works :S
So no my USB doesn't work, but the USB jig does... that's really got me confused
EDIT: Yeah, I did think about software, so I tried to install a different ROM and then I got scared and thought I bricked the phone (it didn't like that wrong USB version was there I guess). I'll see how that goes.
I tried a different cable. The weird thing is it sort of slowly died, and I had to stick the cable in at a weird angle and stuff, so that's why I thought it was the USB port.
As I understand it, there are 5 (?) connectors in the socket. Each connector when paired with the common or ground contact (probably the shielding on the outside of the socket) will perform a different task (that's probably an over simplification of the sockets functionality.........but you get the idea)....eg/ data transfer in, data transfer out, charging, jig resetting, usb docking, usb otg.....that sort of thing.
When you get the situation you're in, it simply means that the relevant connector for the required task is damaged or worn out.....but that doesn't mean that ALL the connectors are affected.... ..that is why some functions work while others don't.......
Sent from my rooted, de bloated, stock JB powered S2 via PhilZ kernel and XDA developers app
Okay so I made (tried to make) a USB OTG cable by taking the metal off the outside of the USB connector, then cutting and reconnecting the cable with red on black and green on white so it would be the same polarity as a female USB. i plugged a flash drive up and nothing happened.
Here is where my retarded moment comes in: I HOOKED IT UP TO THE COMPUTER WITH THE POLARITY REVERSED!!!!
Now it wont even boot up. :crying:
I have a HTC One (AT&T).
PLEASE HELP!!!
I also don't want to send it back because this will be the third phone in 3 months (1st: xperia tl soft bricked returned 2nd: xperia tl hard bricked returned 3rd: i hope it will still work, but i need your help). . i will take ANYTHING except for taking it apart (that's why there is geek squad but that costs money and I'm broke).
if i need to go into more detail i will but please tell me or else i wont know.
wires:
red----------black
white----------green
black----------red
green----------white
i think it blew a fuse, but if so how would i fix it? does it even have a fuse?:crying:
Oh dear! You've lived up to your name anyway. The phone is frazzled!
Next time get a schematic of the cable wiring or buy a cable. It'll be cheaper in the end.
Your phone shop should replace the phone though - just don't tell them your story
CtrlAltDelIrl said:
Oh dear! You've lived up to your name anyway. The phone is frazzled!
Next time get a schematic of the cable wiring or buy a cable. It'll be cheaper in the end.
Your phone shop should replace the phone though - just don't tell them your story
Click to expand...
Click to collapse
that is not what i wanted to hear but thank you anyways. :crying: :crying:
maybe since it wont boot up at&t wont have any way to know about the unlocked bootloader and cyanogenmod (they let me get a new phone for free even after rooting and bricking both my xperia tl's. All i had to do was say that the update broke itor the battery wouldn't hold any charge.) But I JUST got it two or three days ago so I feel very crappy now.
at least i have google voice on my computer and kindle fire.
WHY DIDN'T I WATCH THE STUPID VIDEO!!!! the answer is i am a freaking idiot.
When you say "phone shop", does best buy fit in that category? or is there any possible way to fix it from home?