[Q] Restoring SC card to allow flashing - HD2 Windows Mobile 6.5 Q&A, Help & Troubleshooting

My 2GB SD used to let me flash my HD2 by putting the LEOIMG file on it.
I didn't use this method much, but it was always a good feeling, knowing I could, at any point, revert back to stock settings (SPL and all that jazz included) in case something goes wrong.
However, after trying out WP7, despite having re-formatted the card, I can no longer use it to do this.
I've tried partitioning with EASUS Partition software, I've tried fdisk under Linux and GPARTED. The card consists of a single FAT16 partition and that one file.
However, if I put the card in and boot the phone up holding down the Volume Down key, it'll enter the bootloader, flash a grey screen for a fraction of a second (I suspect it's the screen that lets me flash from SD card, but then something goes wrong), and then reverts back to the bootloader.
Does anyone know what could be wrong? I'd like to stress that the SD card DID once work fine.

Needs to be fat32 not fat16

samsamuel said:
Needs to be fat32 not fat16
Click to expand...
Click to collapse
Ahh, K. But still the same. :|

did you remove the stangely formatted wp7 partition?
Also, when bootloader flickers grey for a second, that can be bootloader looking at the file and checking it for deviceID and carrier/regionID, and finding a mismatch.
you will get this behavour if, for example, you try flash an incorrect rom (cooked, radio, splashscreen, different language, whatever, something that would require hspl) whilst hspl isn't installed

Ahh, it never occured to me that the file I extracted might have become corrupted, and I kept copying it over and over and over again.
Re-downloading the firmware and extracting the image file worked.
THANKS!

Related

Upgrading ROM using a Mac?

Yes, I did a search and google but still can't find a clear answer. I have just bought a 8525 with ATT and want to start loading those cool WM6 rom's I see all over the site. Problem is I have a Mac and can't figure out how to make it all happen. I use Missingsync and can load cab files with no prob but even trying to load Hard-SPL-V7 is not workning for me. I mean, I can get it on the phone but can't make it open or do anything else. I have checked all the great "how to" files but none seem to address this Mac situation. Any help in pointing me in the right direction would be MOST appriciated.
Thanks in advance;
Stephan Howard-Cooper
You'll have to use a virtual environment via Parallels or VMWare Fusion. Or get Boot Camp up and running and reboot into Windows.
Finally, you can also do the SD Card method for OS upgrade detailed in the Wiki.
I've done all methods except for Boot Camp without issue.
Hi
Pof's HERMflasher seems to work with Intel MACs too.
http://forum.xda-developers.com/showthread.php?t=296436&highlight=hermflasher
Thanks for the reply guys. I have tried the SD method but must be doing something wrong. I renamed the nbh file and then put all the extracted files onto the card. When I attempt to bootload I get to the tricolor screen but nothing else.?????
luria said:
Thanks for the reply guys. I have tried the SD method but must be doing something wrong. I renamed the nbh file and then put all the extracted files onto the card. When I attempt to bootload I get to the tricolor screen but nothing else.?????
Click to expand...
Click to collapse
First, you need to have HardSPLv7 installed. A.f.a.i.k. this does not work with unmodified bootloaders.
Next, you need to make sure that your MicroSD card is formatted using FAT32. The FAT32 cluster size also matters (for my 2gig card, 8k or 4k cluster sizes worked, 16k or 32k cluster size did not).
You dont need an empty sd card for it to work either. As long as the card is formatted correctly (as above), and you put a file called HERMIMG.NBH in the root directly, it should work.
When you soft-reset, you should see a white screen that says "Loading..." for a split second, and then if it detects the HERMIMG.NBH, you should see the prompt asking you if you want to start flashing. It will also tell you what you are trying to flash (IPL, SPL, Splash, OS, GSM, ExtROM, etc.).

Flashing from the SD card without formating the card

Hi,
Since I mostly use Linux and Mac OS X, it's not very easy for me to flash my TyTN. There is an article in XDA-Wiki which describes a way to flash my device from the SD card, but it mentions formatting the card before doing the upgrade.
Is it absolutely needed to do so? I have lots of files in my card and I don't want to move them every time before I flash my phone.
Thanks in advance for your answers.
AFAIK, as long as your card is formatted in FAT32, then it should work.
CRCinAU said:
AFAIK, as long as your card is formatted in FAT32, then it should work.
Click to expand...
Click to collapse
Thanks for your answer, a test will convince me ...
i can confirm that you don't need to format it as long as it's FAT32. I can't flash ROMS at work for some reason (no admin privileges, i suspect) and so I occasionally flash from my SD card. It actually works really well.
Above posts are corre correct. I flash from SD card all the time, in fact i have NEVER used a cable to flash my phone. As long as the SD card has been formatted as fat32 you can flash from it without removing other files. I keep all my cabs, sms\contacts backup, files, contact pics, etc. in folders on the SD and then copy the .NBH file to the root of the card and flash away, makes it easy to change ROM's with minimal fuss and can even be done without a computer. About two weeks ago I found myself stuck in an airport and downloaded a new rom via airport wi-fi, extracted nbh file with pocket rar, renamed and saved to SD and viola, new ROM.
I confirm that too. What you absolutely need is to have it formatted in FAT32. SDcard flashing is the only way i use too. BUT... (yes... there is a ...but...) it happens that the "hermimg.nbh" is not detected if it is not one of the first files on your card. In this case, when you "hardreset", no file will be found. This is why i recommand to format it before.

6800 bricked - titan startup screen HELP

ok, before the flaming begins, I'm a noob and should have never even messed with this thing. ok, there, I said it.
alright, a month or two back, I upgraded my 6800 to the nochem 5054 rom. phone worked awesome, no problem.
I'm selling the device and need to flash back to the stock verizon rom. the only place I saw a link to the stock rom, the ftp was down so I couldn't download it.
so I found this thread http://forum.xda-developers.com/showthread.php?t=350539&page=1 and figured it sounded like a good substitute. I downloaded the exe and it installed. finished flashing and said that it was successful. only one little problem (and I've searched for an hour and haven't found the answer...)
it won't boot. it just sits at the HTC TITAN boot graphic. not the tricolor loader. I hard reset but still no fix. once I reset the phone it displays the cresent graphic with HTC TITAN at the bottom, then the little red parameters come up and this is what they say:
M09
H3B60B3FA
P DCAAXAM-4350
R 3.35.04
D 2.17
so, the phone won't boot and I can't get it to connect with activesync to try and reload that rom.
damn. What now?
You have a non GPS rom with the 3.35.04 radio, which is incompatible.
awesome. now I know the problem, I just need a solution.
and do you have any idea where to find a STOCK vzw rom? I guess I need a radio too.
someone please <sniffle>
Go to www.ppcgeeks.com There is a Verizon stock rom on the FTP site....find by clicking QLinks tab at top of page. Go to Titan folder and inside you'll find 'Carrier ROMs'...there is a Verizon ROM inside. Uploaded in March of this year...I don't know what version...I'm on Alltel. Hope this helps.
will I be able to execute that without my pda having an activesync connection though?
yeah, I just finished downloading the stock rom (THANKS) but I can't get the pda to sync up. I guess because it won't boot, it won't connect to my PC either.
what bootloader do you have installed?
gcincotta said:
what bootloader do you have installed?
Click to expand...
Click to collapse
how do I find out? I originally got buildos from ppcgeeks and I chose the 5054 option. I used some unlocker first, then I used buildOS and flashed the device.
is the bootloader in any of those parameters I put above?
Hold power, camera, and soft reset using the stylus while holding them, should put the phone into the bootloader.
It should say at the top:
TITA100 MFG
SPL xxxxxxxxxx
CPLD-9
Tell me what it says where the xxxxxxxx is.
SPL-2.40.Olipro
THANK YOU SO MUCH
I have downloaded the titan relocker and also the correct stock rom from the titan wiki area, the 78MB on. I believe that has the radio too.
geez, I should have never messed with this thing, I don't even know what a radio is....
Ok this is what you need to do. Since you have the 3.35.04 radio and 2.40 bootloader you need to flash a 3.x.x GPS rom in order to be able to boot again. Unfortunately because you can't boot and establish a usb connection, the only way out of this mess is to flash with a microsd card that's less than 2gb. If you don't have one, get one. You'll also need a card reader as well so you can format it correctly.
1. Download this file It's a clean verizon 3.x.x rom and will allow you to boot again.
2. Format your microsd card using a card reader in windows as FAT32 using a cluster size less than 4 Kb.
3. Place the file you downloaded on the card.
4. Insert the card in your phone and enter the bootloader again.
5. The bootloader will say "Checking" then will prompt you to press the power button to begin the update. Press the power button.
6. When it's done, soft reset with the stylus and the phone SHOULD boot into windows mobile allowing you to get an activesync connection.
Now all you have to do is relock your phone using titan_relocker (follow instructions carefully and exact), then flash the stock rom and radio. Make SURE you relock though, and make sure you use the correct rom and radio this time.
ooops .... GC has you all lined up .....
az
well, rather than buy a card and reader, I thought I could shortcut by borrowing a card from someone, then I used my wife's 6800 to format it with pocket mechanic. I chose fat32 and 2K cluster size.
copied the file from my laptop to my wife's 6800 which had the card in it. popped it in my phone and went into the loader but it just says serial.
Is it necessary to have a card reader and format through windows? if it is, I will go buy one and do it that way. my buddies card is only 64MB but that's ok because the file is only 45MB.
let me know about the reader so I know if I need to run to the best buy real quick. wow, making progress.
Yeah you can't format the card using the phone. You also can't copy the file to it using the phone. Go buy a cheap one. You don't even need a card reader, you could use one of those sd to usb dongles and it would work fine. (If you choose to go this route, just make sure the card you buy comes with an sd to microsd adapter). Just can't do it using the phone.
ok, I got a 1gb card with the standard SD adapter.
I went to format it in my laptop and I used fat32 but it didn't give me a cluster option. it just said default allocation size and It was not able to be changed.
anyhow, formatted and copied the .nbh file over and turned on but it just says serial and does not look like it was reading from the card...
moveright said:
ok, I got a 1gb card with the standard SD adapter.
I went to format it in my laptop and I used fat32 but it didn't give me a cluster option. it just said default allocation size and It was not able to be changed.
anyhow, formatted and copied the .nbh file over and turned on but it just says serial and does not look like it was reading from the card...
Click to expand...
Click to collapse
Go to the XDA-Wiki at the top of the page and click on it. You'll see all the HTC models...scroll down until you see the Titan model...click on it. Scroll about halfway down the page to the section titiled 'Tutorials'...you'll see a topic called 'Getting started with your Titan'...click on it. This will have a section on flashing via SD card. It explains how to format the card in DOS. For some reason many times when formatting thru windows stuff doesn't work...I have no idea why...but when you format thru DOS its almost failsafe. Good luck....make sure its in the root directory of your card and labeled TITAIMG.nbh
moveright said:
ok, I got a 1gb card with the standard SD adapter.
I went to format it in my laptop and I used fat32 but it didn't give me a cluster option. it just said default allocation size and It was not able to be changed.
anyhow, formatted and copied the .nbh file over and turned on but it just says serial and does not look like it was reading from the card...
Click to expand...
Click to collapse
Flashing a phone with a micro SD card
1. Format a microSD card into FAT32 with an allocation unit/cluster size of 1024
(the default size for a 1 GB would not work, also if it takes only a few seconds to format
try formating with some other slot/device. A 1 GB took over a minute to format correctly)
To format your Card - Open a DOS box and type/copy and paste this: ( format ?: /FS:FAT32 /A:1024 )
Replace the ? with whatever your SD cards drive letter is... ie: f, h, I.... Mine is G....
2. Copy the ROM to flash (xxxxxxxx.nbh) to the root of the microSD
3. Rename the ROM xxxxxxx.nbh to TITAIMG.nbh
4. Insert your card.
5. Force into the boot loader with POWER-CAMERA-RESET
6. Follow the instructions and you'll quickly flash your Titan...
That was in the Titan Wiki - You can use a DOS box to format, do not use Windowz Explorer....

Flash from SD using SPL?

Is there a way to flash the Raphael without Windows, just by booting it into SPL and inserting a microSD with an image on it?
Why I'm asking? What, if a new ROM bricks the device in such way, that ActiveSync will no longer connect to it? RaphaelCustomRUU.exe will not work anymore.
If you have HardSPL you can flash from the SD card. I have flashed 6-7 custom roms on my TP and I haven't used the custom RUU for any of them.
knight14th said:
Is there a way to flash the Raphael without Windows, just by booting it into SPL and inserting a microSD with an image on it?
Why I'm asking? What, if a new ROM bricks the device in such way, that ActiveSync will no longer connect to it? RaphaelCustomRUU.exe will not work anymore.
Click to expand...
Click to collapse
I had this problem with ROMeOS v1.04, activesync just did not connect and no programs started, rebooting did not help. I already thought my phone to be brick!
Just press volume down and powerbutton to turn it on (should be off before of course) and you will end in the bootloader, flashing with RaphaelCustomRUU.exe works if the phone is on in bootloader mode and connected to computer. (thank god!)
XL3N7 said:
If you have HardSPL you can flash from the SD card. I have flashed 6-7 custom roms on my TP and I haven't used the custom RUU for any of them.
Click to expand...
Click to collapse
Instructions would be nice if provided also....
I guess im the only one who cannot flash a ROMeOS rom from a SD-Card.
I've tried everything formatted the card to FAT32 renamed the .nbh to RAPHIMG.NBH tried caps and non caps. I even tried to format to regular FAT but still no go.
As you can see in my signature i have flashed Hard-SPL 1.90.OliNex
Mine are called RAPHIMG.nbh and they have to be in the root map of your SD, I do this with al the new ROM flashes, because I believe it's faster and you don't have the battery limit (which is there for good reason of course). So root map and there you won't see .nbh in the root map, just RAPHIMG. hope this helps
12aon said:
Mine are called RAPHIMG.nbh and they have to be in the root map of your SD, I do this with al the new ROM flashes, because I believe it's faster and you don't have the battery limit (which is there for good reason of course). So root map and there you won't see .nbh in the root map, just RAPHIMG. hope this helps
Click to expand...
Click to collapse
What do you mean with in root map you won't see .nbh? Do i have do delete the extension if so then that has never been clear for me
WatskeBart said:
What do you mean with in root map you won't see .nbh? Do i have do delete the extension if so then that has never been clear for me
Click to expand...
Click to collapse
You need the nbh file extension. It just won't show if you have "Show File Extensions" turned off. If you use FileExplorer on PPC, you'll see RAPHIMG not RAPHIMG.nbh. (Check the file name in Windows or TotalCommander to be sure).
The file must be on the root of you SD Card and it should work, unless the OliNex HardSPL has some extra options / checks.
Ta
Dave
DaveShaw said:
You need the nbh file extension. It just won't show if you have "Show File Extensions" turned off. If you use FileExplorer on PPC, you'll see RAPHIMG not RAPHIMG.nbh. (Check the file name in Windows or TotalCommander to be sure).
The file must be on the root of you SD Card and it should work, unless the OliNex HardSPL has some extra options / checks.
Ta
Dave
Click to expand...
Click to collapse
I already thought he meant the hide extensions thing but just to be sure
I've tried RAPHIMG.nbh but it doesn't work for my device.
I also own a Hermes and just flashed it the SD-Card way with HERMIMG.nbh and that device works perfectly, so it isn't a card problem.
Could it be an Hard-SPL thing then?
WatskeBart said:
I already thought he meant the hide extensions thing but just to be sure
I've tried RAPHIMG.nbh but it doesn't work for my device.
I also own a Hermes and just flashed it the SD-Card way with HERMIMG.nbh and that device works perfectly, so it isn't a card problem.
Could it be an Hard-SPL thing then?
Click to expand...
Click to collapse
I've spoken with cmonex about this and there's no reason it shouldn't flash from the SD card. The code is in Olinex 1.90 to do it.
RAPHIMG.NBH on a FAT32 Formated Card and hey presto
Ta
Dave
I just tried it and it works. The file is named 'RAPHIMG.nbh' on the root of my storage card. Booted into bootloader mode and it instantly loads the nbh file.
Nice to know. So finally I do not have to boot Windows any more
I tried this for the first time just now, hadnt even thought to use the sd card, I usuallly go through all the hassle of using a vm just to flash.
File is named RAPHIMG.nbh on the root of the sd, restart holding vol- and thats it.
dabs said:
I tried this for the first time just now, hadnt even thought to use the sd card, I usuallly go through all the hassle of using a vm just to flash.
File is named RAPHIMG.nbh on the root of the sd, restart holding vol- and thats it.
Click to expand...
Click to collapse
Could it depend on which ROM you flash? Because honestly i only tried to flash ROMeOS with SD-Card. I never tried to flash DCS or something else.
So many people with successful flashes with the SD so i'm almost sure i'm doing something wrong here.
I will try again a soon as a newer ROM comes out because i'm a bit tired flashing different ROMs
Thanks for all the support.
I was using ROMeOS v1.10. sd card is a sandisk 6gb. Its hard to see what could prevent it from working for you, hopefully something will turn up.
Ishould also note it is considerably faster flashing from sd than over usb.
Put your miniSD in a card reader and from Windows, right click it and select format. Choose fat32 and leave the volume label blank. If it automatically adds a name delete it before proceeding with the format. After it's formatted, place your RAPHIMG.nbh on the rott of the card. Enter bootloader by holding volume down and pressing reset and it will find the image file. From there follow the on screen instructions and it will be done in a few minutes.
S ¤ F ¤ W
dabs said:
.../... I should also note it is considerably faster flashing from sd than over usb. .../.
Click to expand...
Click to collapse
It is indeed. It is:
1. Safer [Risk free if you ensure you have at least 50% of battery left.]
2. Faster [Way much faster.]
3. Windowsless [that's a blessing!]
Good luck.
Cheers.
I had problems too flashing hang.tuah's rom but only 1.05 it would flash but not boot up, i tried through 2 pcs and via flash card.
i couldn't flash by my actual card cause from what I read sdhc isn't necessarily supported in bootloader, so i borrowed a friends 2gb microsd and that worked with flashing.
Since there is a new version of ROMeOS i'm gonna try it again.
I'm going nuts over here
I renamed the ruu_signed.nbh to RAPHIMG.nbh and copied it to the root of a FAT32 formatted SanDisk 2GB Ultra II card (non-SDHC) and check it for errors.
When i insert the card and reset while pressing the volume down button to enter the bootloader, the device says "No Image File Found" and just stays in the bootloader
What am i doing wrong here??? It's no that a big deal because i can flash using the wrapper but it should also flash with the SD-Card.
I'm almost giving up here
If there are any more idea's bring em up

Restore Internal SD Card from zip ROM streak 5

Hello friends, how are you?
I'm from Portugal, and i have one nice strek 5 working great.
But i have another two, that don't boot, it stuck on delll Logo.
i think another my friends try to root or update, and fail.
it don't make any fast boot or streak mod.
so i disassemble to read its sd card.
because i'm using windows, so i install DiskInternalls Linux Reader to have acess to sd card files.
When mounted, its show two volumes, "Linux Ext Volume 1" and "Linux Ext Volume 2"
the firs one have 244 Mbs, and the other one have 1.65Gb
the small one have two folders, lost+found, recovery and a lot of jpeg files in root folder.
the second one, that have 1.65Gb, have a lot od folders and semms a lot of a zipped rom image.
Its possible just decompress and copy to the volume?
Thanks
If you format the card and put it back in the streak, it should set it up automatically. However, you will lose anything on it this way.
Ok. i will try..
but, it don't need to write some data in "boot area" ?
I'm asking that, becouse i download 3 roms, all ziped, but easy to see files, i also download streak mod, and has only one img file, it can't be unzipped..
my firts idea, was copy streak boot files, to card, but i can't acess it..
My assumption, and it is only an assumption, is there is some sort of actual rom memory on the phone that holds the lowest levels of the operating system. Maybe fastboot and the recovery menu, but not recovery itself. The rom actually resides on the internal sd card. When I put in my freshly formatted sd card, I simply rebooted the phone and I don't remember if it was automatic, or I had to confirm it, but the streak partitioned/formatted/whatever the internal sd card itself. I then flashed a recovery and a rom.
Hello.
like you said, i have insert a new sd card, but formated in FAT, i think thats the problem.
I try to load Linux Live CD, and format in ext2/3.
or try to copy rom directly file to sd card.
You think might work?
***EDIT***
I have format the card, and i have inserted into sreak and turn it on..
How much time is preparing the new card ?
and how i know that is ready to reboot?
thanks
I have created an image of my inner SD Card right after a factory reset.
Download Here
I created this using Clonezilla, you should be able to use Clonezilla to restore it. It is an image of the entire sd card. You need to unzip the downloaded file to use it.
Note: I am running DSC_Rom, which is Gingerbread based. I don't think it makes a difference.
marvin02 said:
I have created an image of my inner SD Card right after a factory reset.
Download Here
I created this using Clonezilla, you should be able to use Clonezilla to restore it. It is an image of the entire sd card. You need to unzip the downloaded file to use it.
Note: I am running DSC_Rom, which is Gingerbread based. I don't think it makes a difference.
Click to expand...
Click to collapse
cannot start clonezilla iso
slav_pu6 said:
cannot start clonezilla iso
Click to expand...
Click to collapse
You burn the .iso file to a cd and boot it.

Categories

Resources