Hello i recently updated my htc hd2 phone to - official ROM version 3.14.479.2, Radio version 2.15.50.11U from the site - htc.com. My problem is that the camera flash light does not work when switch to always on mode. The flash light would be not on until I take a photo which acts the same as the auto mode.This problem is in camera mode.IT WORKS TOTALLY FINE IN THE CAMCORDER MODE!
Battery is 100%
Soft reset doesn`t help!
Is there any registry solution what to do or only hard reset (htc technicians couldn`t find solution and adviced me to do hard reset)
sekojpetokurdajadam gmail com
Thanks in advance for your help.
Related
Please help me fix the camera of my Cingular 8125 G4 device. After I flashed a new rom using soft SPL method, which I think G4 safe rom, the camera is not working. When I press the camera button, I only see the spinning circle with different colors and the screen lights up a little bit than the normal brightness and stuck it there. And after a few seconds, the phone hangs up. Need to soft reset in order to put back the device in a functional state. I don't know why this happened as I followed all the necessary steps in using softSPL upgrade method. Maybe there is something wrong in the device registry. Does anyone has the same camera problem. Please share the tricks, tweaks or anything just to bring back the camera function again.
BTW, I reflashed back the official cingular stock rom but no luck at all its the same.
I see that you are using the TNT ROM, so I would to and flash UP to the newest version and see if that fixes your problem, it sounds like the camera software and drivers are not getting installed for some reason.
I reflashed the tnt rom but no good. Tried also to go back to the original cingular stock rom but still not working. Even in the windows\camera cannot make it. But when tried not to use the device for a some hour in standby mode, the camera works for a while then it hangs up. And go back to non-functional state.
Sir, what you think is the problem? I suspect its the software installed in the device based on what the camera behave. Or definitely the hardware itself and need to replace. Bad for me because I am living in the Philippines and as far I knew there is no service available in our country.
Thanks in advance whatever help you can give. Have a nice day.
Try using the wizard service tool to increase your page pool to 6mb.
Camera work again after....
My dead camera work again after I flashed rom cooked by Cracing. This rom is awesome. Its compatible with Wizard. Thanks to Cracing.
Hi everybody:
I installed the udk syrius 7 rom Polaris, when activate my camera
it doesn`t show imagen, it`s black andy show the news
text:
Unable to capture photo. Unable to get frame data from
camera device.
Can you help me??
Thanks a lot ¡¡¡¡
Same here!
Same here!
I tried several roms and I still have the same issue.
Tried downgrading the radio, didn´t work either...
Could it be the SPL?
I have had the same problem. I have resolved with a new one flash of ROM
SPL is OK !
Just go back to a original rom (incl radio) and after that try again.
If that doesn't work just try a other radio rom.
Most of the roms have different radio requirements
Some need 1.58****
Other need 1.59****
Normaly the rom maker gives that info.
Sometimes the camera malfunctioning is a software issue.
As i experienced it is a hardware issue when you still have the troubles when you go back to original rom and radio rom. Although there are tons of users which get the camera to work after installing some package etc, my defect was loose connections on PCB/CPU or something similar. Thats why the problem starts slow, sometimes it works, somethings it doesn't and in the end it doesn't work at all.
The only thing you can do then... is return it for warranty.
Hello all.
I have a problem with my new NEO, secondary camera stopped work after week. It doesn't work from service menu or from any application which use them - all of apps just stop to respond (black screen). Hardreset and flash didn`t help me. I have tried to do it with SEUS (4.0.2.A.0.42) and with the latest Flashtool (4.0.2.A.0.62) - no result.
Can anyone help me ?
Thanx.
Thats HW problem... try to go to the service.
Hallo XDA Friends,
I have a problem with the LED on my month old s3 ( euro unbranded )
Everything was going great with the LED I Installed Light flow everything was still fine.
I updated to JB official stock rom as i am unrooted, and since then the LED only works when
i boot up the phone and when i use the Test utility ( red green blue ) colours. With lightflow uninstalled
and no LED management software still nothing works. Also not with screen off.
Now I am stuck because it clearly is not a Hardware problem as It works on boot and in test mode,
But not in anny other situation.
I hope someone here can help me and thanks in advance!
Backup data and factory reset .
jje
I have a lava iris x8 (running kitkat) yesterday I hard reset it through recovery and noticed that it's camera doesn't focusing give a blurr image(like a digital or VGA camera) and Its not fallen so there is no chance of hardware problem. Now I hard reset it again. Update it (now on lollipop) but nothing work. Tried google cam and cameringo. Help me . Does camera drivers are faulty or is it something else