I am desperately need help with my phone. I had installed GingerDX v13 from Cyanogen Froyo CM6 v6.01 and it worked fine except it will reboot every half hour so reinstalled the previous one i was using "Cyanogen Froyo CM6-Latest (based on MiniCM) - v6.01" and did wipe data/factory reset before and after installation from xrecovery (with every new rom install) then restore from Titanium backup as restore all apps and data (not System) and rebooted.
After reboot all problems started. It just gives me Force Close errore one after another and do not stop. If i lock screen, it shows errors in few seconds and if i do not do anything it just reboots. And all cycle statrs again.
I tried to go into recovers at startup by pressing back key after Sony ericson shows up on screen, but no luck.
Can you pleaseeeee help? I installed many updates without problems but this time no luck. My be some commands for abd shell to do factory reset and clear data?
Thanks
Have you tried seus with your phone turned of connect to pc while holding all 3 menu buttons. Ive seen a postsome were in the forum but cant remember were. I think thats how you do it.
Edit found this on a post
Turn the phone off for 30 secs. or so
connect the USB to PC
hold back button
connect USB to phone
the Green LED should light up indicating that the phone is in flash mode, just incase you have to flash your old rom back.
Sent from my U20i using xda premium
wrong forum category. Go to qa.
Looks like your downloaded file possibly is defect. Check checksum.
sent with my x10 mini pro
SUSE shows there is no update available, i can not connect phone to adb.
The 3 button thing, i do not know how it works.
Please help
On seus just click support zone then phone software update, it will say your phone is up to date but just click repair.
Sent from my U20i using xda premium
No luck with repair using suse. It says no update available.
Sent from my SAMSUNG-SGH-I897 using XDA App
FlashTool did the trick, i used Singapore firmware and got updated successfully. Thanks for your help.
[TUT] un-brick for newbies
This has been covert alle over XDA in every forum and every thread.
I never really understod the problem. I have bricked my X10 mini pro alot, and never had any problem at all to fix it again.
Sorry for the danish screen-shots.
1. Make sure the battery is not totally dry.
2. Turn off the phone (this is very important).
3. Download and install PC Companion.
4. Start PC Companion and start Support Zone.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
5. Click on Start under Update.
6. Click on Repair phone.
7. Click on Continue.
8. Check the little box and click Next.
9. Sit back and wait.
10. Mark the X10 mini pro and click Next.
11. This is the part every one fails, so listen up.
Step 1 - 3 (unplugged, battery not dry and phone turned off) Is already done. If not make sure they are.
Step 4) Plug one end of the USB cable into the PC
Step 5) HOLD DOWN THE BACK KEY ON THE PHONE AND PLUG THE OTHER END OF THE USB CABLE INTO THE PHONE.
12. Wait until the the update starts. Wait to release the back key, untill you can read a small text saying that you don't have to hold down the back key anymore.
Related
Hey there.
First post. I used Odin 3.1 to flash Froyo 2.2 on my Vibrant that was running Eclair 2.1, and Odin showed a successful completion. The phone then turned off and instead of re-booting, has become totally, utterly unresponsive.
I have tried a number of ways to get it to work, or at least get in to Download or Recovery mode, including the "remove everything, then re-insert battery while holding down volume up/down keys" and any number of key combinations. I've trowled the forum and haven't found a single solution for a completely unresponsive Vibrant. even the USB jig seems to be for those phones that at least show the Vibrant Logo or the "S" at start-up, while mine doesn't do anything.
The only encouraging thing has been posts by people who claim to have lefft their unresponsive Vibrants plugged in for several hours only to have them miraculously revive, but that seems like a long shot to me.
Have I managed to do the impossible and brick an unbrickable phone? I'd really appreciate help as I just got the phone last week and don't want to declare it a dead loss so soon.
Cheers!
Utterly, haha
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
thinking.. above was a joke...
What ODIN files did you flash? Link to them?
What version of ODIN, the latest?
When you say nothing... you mean you can't see anything on the phone, regardless of the action?
rofl OMG is that chick half naked hahaha seriously is she in her undies milking a cow WTF! LMFAO!
- so the phone won't turn on huh?...... no power at all?....... how about plug in the cord, do you see the batt charge?
haha utterly.. when you say put in the battery while holding the volume keys, did you put in the battery or plug in the USB??
I had to replace mine. Been good ever since.
Sent from my GT-I9000 using XDA Premium App
Here's the long story. My phone was getting the 'device unrecognized' error in Kies and Kies Mini, so I used Odin 3.0 to flash it, using the "T959UVKA6_REV05_home_low_CL860813.tar.md5" file.
After flashing, my phone wouldgo into recovery mode and the following error.
"E:Cant mount /dev/block/st110
(invalid argument)
E:copy_dbdata_media:cant mount DBDATA:
copy default media content failed."
Next I followed the steps detailed in this post . When I flashed my phone according to the 'Gauranteed Solution', my phone turned off at the end of the flash and has stayed off ever since.
And when I say nothing, I mean nothing. No battery symbol, no sound, no Samsung Vibrant logo, nothing. Just a blank screen.
I tried plugging in the phone and then putting in the battery with the volume keys pressed and I also tried it without plugging in the USB. Either way, nothing happens.
As you can probably guess, I'm a n00b of the first order and I fear I might have killed my phone.
If you do manage to revive your phone back.. You better flash roms via cmw. Not that odin isn't great but cmw never caused any problems(to me).
Make a jig to force download mode then reflash stock os and install rom manager to flash roms. P.m for more Info.
Sent from my SGH-T959 using XDA Premium App
Thats funny, the last post in the link you referenced is someone having the same problem as you........ why would you try to do that? and the .tar is some I9000 file being that the (fix) was in the I9000 forum. Neither of these probably have anything to do with your problem now i just thought it was funny. I mean why wouldn't you just use the T959UVJFD.tar in ODIN?
It seems that the "E:cant mount" error is a fairly common issue and from what i am seeing alot of the people having this issue after using samsung kies are getting replacements fairly easily although it is a last resort for many. I would not think its an issue with your drivers or anything like that, probably just ODIN being weird. Don't give up on ODIN i would assume that it will recognize the phone eventually as most "DEAD" vibrants do after time. I'll keep looking into it for you. Hope you find a fix soon. Good luck!
You can also restart the computer and f8 and turn off driver signing and see if that helps. Once again I don't mind helping on a more personal basis. P.m me.
Sent from my SGH-T959 using XDA Premium App
have you ever actually tried a usb jig ?
http://cgi.ebay.com/ws/eBayISAPI.dl...83134&ssPageName=STRK:MESELX:IT#ht_723wt_1139
i enabled jit through xrecovery , but now my phone is stuck at the 1st logo screen?????????
means the jit update failed. go to xrecovery screen again and then restore, if you have made a backup
d0wnl0ad said:
means the jit update failed. go to xrecovery screen again and then restore, if you have made a backup
Click to expand...
Click to collapse
How it is possible to go back in xrecovery if we cant switch off phone..
please help
yogeesharma said:
How it is possible to go back in xrecovery if we cant switch off phone..
please help
Click to expand...
Click to collapse
Pull the battery from the phone then put it back in after a few seconds, then switch on or keep it switched off and connect to pc via usb and use seus or flashtool to repair the phone
Sent from my X10 Mini Pro using xda premium
Lancerfq said:
Pull the battery from the phone then put it back in after a few seconds, then switch on or keep it switched off and connect to pc via usb and use seus or flashtool to repair the phone
Sent from my X10 Mini Pro using xda premium
Click to expand...
Click to collapse
Nice tip but the x10 Mini has no "loose" battery.
if this is a "bootloop" you need to use SEUS and redo the whole thing with root and reainstall everything inc. custom ROM.
What you could do with the battery is:
Take back cover off, there is a small rubbery "plug" pry that away from the phone.
Beneath that rubber you can see a white electrical socket.
That socket is connecting the battery to the phone.
That COULD dp the trick.On occassions..
Yeah when I posted it I didn't notice he meant mini, was my bad, flashing with seus is what I also mentioned so can forget pulling the battery part
Sent from my X10 Mini Pro using xda premium
Lancerfq said:
Yeah when I posted it I didn't notice he meant mini, was my bad, flashing with seus is what I also mentioned so can forget pulling the battery part
Sent from my X10 Mini Pro using xda premium
Click to expand...
Click to collapse
Anu efforts in helping are good..
I think there is a little button
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sent from my U20i using XDA App
gaga0101 said:
I think there is a little button
Sent from my U20i using XDA App
Click to expand...
Click to collapse
Push that and you void you´r warranty.
It is NOT a button, it´s a humidity test tape that is hidden.
Here: Within the square circle.
it didnt work
hey it did not work , the removing plug thing any other method???
kartiknnn said:
hey it did not work , the removing plug thing any other method???
Click to expand...
Click to collapse
You can always pres the home and power buttons at the same time, it will do a hard reboot. Pressing the back-button several times when the kernel logo shows up should get you back into xrecovery.
If you need flashmode, press home and power and as soon as the screen goes off (completely black) press the back-button with the usb-cable already attached to your computer and your phone.
Hi,
Hope u help me guys as im really sad my TG01 looking completely dead.
What i did. I wanted just flash new soft from Miro so i charged the phone and did flash my phone from SD card as i did many times. After my phone stack in Logo TOSHIBA and just flash over and over. So i found the way how to unbrick the phone. So as they said i conected the phone to charger and after i connected pin 1-3 and press the power button the mobile vibrate and that was the last thing hi did. After that i cant charge it, screen is black, mobile is not connecting to PC at all (pc dont even recognise that the phone was connected to USB no sign of new usb item or start to instal drivers or so) so i dont really know what happend or whats wrong. I installed TG down loader with driver but there is no sign of connection after i connect phone to PC.
Can anybody help pleas ????
MarvX said:
Hi,
Hope u help me guys as im really sad my TG01 looking completely dead.
What i did. I wanted just flash new soft from Miro so i charged the phone and did flash my phone from SD card as i did many times. After my phone stack in Logo TOSHIBA and just flash over and over. So i found the way how to unbrick the phone. So as they said i conected the phone to charger and after i connected pin 1-3 and press the power button the mobile vibrate and that was the last thing hi did. After that i cant charge it, screen is black, mobile is not connecting to PC at all (pc dont even recognise that the phone was connected to USB no sign of new usb item or start to instal drivers or so) so i dont really know what happend or whats wrong. I installed TG down loader with driver but there is no sign of connection after i connect phone to PC.
Can anybody help pleas ????
Click to expand...
Click to collapse
hey my friend
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
why press power button
plase do this step! by step!:
2 Short-Pin unbrick method
1. Copy a functional ROM on SD Card. PRG folder
2. Rename to TG01WP_00.enc
3. Put the battery in and plug Power- Kable. Charging LED flash RED *
4. short pin 1 and 3 (back side under sim card, remove black plastic) Hold the short and RESET. Hold short pin 1 and 3 for 10 sec. Display go on and ROM flash beginn
Yes i did tray this couple of times but with no success , when i plugged charger the charging red light dont flash red but i tray it anyway with charger on and off aswell.
I did it with the power button cose i read that somewhere and im scared i did burn or so something in MB as i had power charger plugged in i then short the pin 1 and 3 and then press power button. this is probably very bad way to go. the mobile is not responding to anything i tray
My TG01 has the same problem. I tried many times to flash a new ROM by "2 Short-Pin unbrick method" but nothing. @mirolg if you have some other ideas we are glad to hear you and to try on our dead phones.
How to Root and unlock the bootloader of Sony Ericsson your Xperia x10
for those stock on 1.6 or 2.1 or soft bricked Go here first: http://forum.xda-developers.com/showthread.php?p=32673686#post32673686
Vote after you have completed all the steps which you desire. and don't vote "Im confused" if you did not read carefully.
Disclaimer: I nor xda-developers.com bear any responsibility for your phone.(this phone is not bricked easy so don't worry if anything goes wrong you could just flash a new stock 2.3.3 with flashtools)
The first time may scary you like it did me the for my first time but now I can do this in my sleep.
1.download latest flashtools which is a program that you would be using as long a you want to flash custom rom from here: http://androxyde.github.com/Flashtool/
2. Now in the Flashtools folder (C:\Flashtool\firmwares by default) go to the folder named drivers and you would see "flashtool-drivers" and install them (installed them all just in-case you decide to get another Xperia phone in the future.
3. On your phone go to setting>applacations>unknown sources and usb debugging in development and connect your phone to your computer with your data cable and then open flashtools.
4. root would now become available in flashtools so press it(the black unlocked lock ICON) and just wait for flashtools to reboot your phone. and you now have root access!
Installing a Recovery
In order to install a new Rom you would have to install a Recovery, according to the rom you want to install the thread would state whether you need a ClockWorkMod(CWM)(CWM5 in flashtools) or just flash through Xrecovery(0.3 in flashtools)
So in order to install a Recovery your phone must be connected to the USB port on your computer. So in flashtools click on the black square with a white cross in it and choose according.( setting>applacations>unknown sources and usb debugging in development much be on.
How to use Xrecovery.
To get into xrecovery you much power off your device, then press the power button until it vibrates, no when you see the sonyericsson logo start pressing the back button on your phone and then you would enter Xrecovery(in the version of flashtools this tutorial is based you must wait until you see the notification LED turns ) now in xrecovery you use the volume up, down, home and back buttons to navigate.
Bootloader Unlocking.
5.unplug your phone and power it off. On the top bar in flashtools plugins should now be available with the "Unlocked bootloader" option, so press it and wait until it says to connect your phone then do so by holding down your back button(on your phone) and plugging in your USB cable(don't let go until you see your notifications light come on GREEN
6. While the unlocking is taking place look out for the "you can now unplug and turn on device, then plug it again" Immediately. Do it that one time and just leave it to finish and say "successfully applied unlock. Rebooting
7. Smile because you can now flash custom kernels and so forth and so on and also press thanks button.
If your stuck just send me a message.
Quick tip:flashing new roms usually means loosing your data(contacts, apps, etc) but you can use this to backup your data and when you're done re-download it and restore your data: https://play.google.com/store/apps/details?id=com.jiubang.go.backup.pro
Return to Stock 2.3.3
If you wanna go back to stock Gingerbread this is the link. download it extract it and place it in Flashtool/firmwares folder wherever you have it.
http://www.mediafire.com/?vxa0kzi87idladf
Return to Stock 2.3 kernel if you flash one you don't want anymore or don't like
https://www.box.com/s/5jiyxpw9xxhfvu07na73
Return to Stock 2.1
http://www.mediafire.com/?w8hz2ev91lpof6h
Rom Suggestions
My pick for the best Jellybean and Ice-cream-sandwich roms for your x10. are Scritch V5 and Scritch CM10.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Jellybean:http://forum.xda-developers.com/showthread.php?t=2012483
ICS: http://forum.xda-developers.com/showthread.php?t=1987130
And FXP CM9 ICS rom for x10:http://rapidgator.net/file/50328026/FXP142-cm-9-20121013-UNOFFICIAL-es209ra.zip.html
FXP latest kernel for Ice-cream sandwich: https://www.box.com/shared/1zebny1do5lacefwdlfa
Gingerbread rom suggestion
Hands down one of if not the best Stock 2.3 based rom for our x10 is make by alzbac DonutHD
its fast, smooth and this good battery life(well compared to stock 2.3.3)
DonutHD link: http://forum.xda-developers.com/showthread.php?t=1574185
for the gamers out there with an x10 DiKeJ has you covered with his gaming rom. you would however have to talk with him VIA message because the rom is not free you would have to donate in order to get this one but all the other are free.
http://forum.xda-developers.com/attachment.php?attachmentid=1119788&d=1339338767
Gaming Rom link:http://forum.xda-developers.com/showpost.php?p=27222178&postcount=35
Hi, Im new to all of this and hope anyone could help me out.
I have a problem with my tv box because of installing
SuperSU.
First of all, my box is rooted from factory. Its a beelink gt king. But super su isnt installed like when you root a phone and it shows. So I tried to install it because I needed to hide my root from some apps/games. I installed magisk but I needed this supersu also apparently? Well, anyway I did. And then the problem of the binary occupied appears. So Im googleing some solutions and it says that first you need to install a previous version and then update from play store but in play store there is no more supersu.
But anyway I installed the previous version, asked me to reboot system, I did, and now I have a tv box that is stuck in the logo. Actually not in logo..it passes the beelink logo in about 2 hours, then comes the skull with glowy eyes and thats when it stays. I have waited hours for the skull to change to the homescreen to no avail.
The second problem is I have been trying to reset the box but I just cant do it or the system cant?. Its really stuck. Maybe Im missing something? I dunno. I push the reset button that is at the bottom in this box, then I plug the power cable, wait some time, release...but nothing happens.
What I am doing wrong?
Please help someone.
And can you tell me a method without a PC? Unbelievably I dont have a PC. And this phone cant be rooted or at least is very difficult to root or so they say (a galaxy note 4 verizon).
But at the end it doesnt matter. Whatever it takes to fix this box. Thank you.
GT KING SD Card Update
Hi Hansell1001, I did the same thing and faced the exact same issue. But i happened to have a PC. But i think this can also be done via a Phone and a SD card.
First download the firmware as per your model (As per your serial number under the box) to your phone.
Firmware: For C922X and SA9X and SB9X versions
http://t.cn/A6zQGfda
Firmware: For B922 versions（04.01.2020 add）
http://t.cn/A6ZNxNkM
Firmware: For S922 versions（04.01.2020 add）
http://t.cn/A6ZNxe7R
1. Now extract the content of the zip file.
2. You should see a folder called “sd_card”.
3. Copy the content of that folder (I.e factory_update_param.aml, recovery.img and galilei-ota-eng.xk.zip) to the root of SD Card.
IMPORTANT: (the SD card format must be FAT32)
4. Insert the SD Card to the SD slot at the side of the box.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
5. Now remove the power cord of the GT King and with the help of a pin, press and hold the reset button at the bottom and insert the power cord.
6. Hold the reset button for 5 seconds till you see the Beelink logo and then release it. Hopefully you be on the recovery screen.
7. From this screen, select “Apply update from EXT” and select the update zip file.
8. Now the box would update properly and boot you back.
I fixed it
I fixed it more than a month ago. Thanks anyway.
I thought xda was quick.
Hansell1001 said:
I fixed it more than a month ago. Thanks anyway.
I thought xda was quick.
Click to expand...
Click to collapse
Ha ha Yeah but i just got the box in Jan i screwed in March so i was looking for a solution but figured it out myself. So when i saw your post, i thought it would be helpful but guess not. But anyway now this would be helpful to someone who may need it.
So let this be a reference for them
Guys, help! I got a GTKing in November 2020, a couple of weeks ago. It worked for a week or so, then it went into boot loop. Firmware is v 914p0 (dated 21 Oct 2020). I tried several things to no avail:
- When reapplying v 914p0, the device reboots to the boot loop
- When attempting to apply v 913p0or earlier, it says it won't apply an earlier version.
I hope someone will drop in some hint on how to get this @#!* box to work.
Cheers,
-Christos
I can't download that firmware
Fordac