Hello,
hopefully this is the right forum for it:
does anybody know how Motorola managed the Audio-signal over the USB-Cable of the car-dock?
They deliver a special cable with every car dock - one side USB Typ A + Audio-Out and on the other side a Micro-USB-connector which has to be connected to the car-dock.
(if you connect the micro-usb into the phone it doesnt even charge...)
In the car-dock is a little circuit for the audio.
I would like to make a similar cable with this circuit implemented (and dont want to buy another car-dock for it).
Any ideas?
Kind regards,
Normen
P.S: for Samsung is a thread available http://forum.xda-developers.com/showthread.php?t=820275
Related
Hi all,
As per subject...
Anyone know if such as cable is available?
I was planning on getting the new 3-1 Adaptor for the TYTN to make use of the 3.5mm jack and charging feature in my car.
The thing is, the cable for this adaptor is very short and cannot be hidden easily when in the car. So, I was thinking of using an extension cable of some sort, so the adaptor could be more easily hidden elsewhere under the centre console.
Many thanks.
USB Stupidity
Hi,
Affraid i didn't find anything either, and wanted to do the same thing.
I resorted to buying the cable from expansis and "Adapting it my self"
The project was fairly simple, and if your happy with a soldering iron and a multimeter you should be fine.
I now have a small connector on my dash that will disapears under the dashboard to a breakout box. All i basicly did was chop off the box that has the two female connectors in it, extend the wire with an old cut up parralel printer cable (multicore and was lying arround) and then terminated in a project box from maplins.
This has two headphone sockets, (audio out stero, and mic in) as well as a USB socket to charge the phone. (the plan was to have the USB socket be usable for data... but that bit went a bit wrong...
Still from the testing i have done, i now have tomtom and WindowsMedia mp3 play back comming through my car stero, and my VarioII reports to be charging. Havn't had a chance to test it on a long drive yet, i think i might still need a beefier 12Volt to USB adapter.
If anyone want more info on what i did, i'd be glad to help.
here are some pics, sorry v bad Q....
I don't seem to see any pics?...
Ooops...
here you go
Seems good to me- as long as it all works ok then its a good job.
Always been interesting in making my own adapters/cables but have never tried. Perhaps I should give it a go!
sh500 said:
Hi all,
As per subject...
Anyone know if such as cable is available?
I was planning on getting the new 3-1 Adaptor for the TYTN to make use of the 3.5mm jack and charging feature in my car.
The thing is, the cable for this adaptor is very short and cannot be hidden easily when in the car. So, I was thinking of using an extension cable of some sort, so the adaptor could be more easily hidden elsewhere under the centre console.
Many thanks.
Click to expand...
Click to collapse
Any news on that extension cable yet; is it available?
i brought one of these and successfully lengthened it with an old peice of printer cable (only multi core cable i had to hand)
i then used an off the shelf diy project box to hide the junction in.
worked very well, but i have since changed to a bluetooth car kit.
the soldering was a little small and working out which wire was which was a bit of a pain, but all in all only took an hour or so to sort out. probably worth it.
(AFAIK my dad is still using the one i adapted.)
sorry to put old post on top !! but own a dimaond and just buy a touch HD !
i a m looking for this kind of cable !!
If someone have info !!
where to buy for exemple ?
thanks in advance !!
how about extending the power cable? seems like that would be easier.
3in1 11 PIN ExtUSB Earphone Handsfree Adapter for HTC
Other option: http://cgi.ebay.com/3in1-11-PIN-Ext...AU_MobilePhoneAccessories&hash=item3cabfd9d0b
Hi there,
I was wondering, if it's possible to get a GNS Trafficbox FM9 connected to the HD2 (via adapter) to receive TMC-Data.
HyperGPS isn't working so far, so this could be the proper alternative...
Anybody's got some experience concerning this?
I've just bought a GNS Trafficbox FM9 which has come with a mini-B USB plug to use with my HD2. I've also bought a micro-b USB extension lead.
Taking the Trafficbox apart reveals a simple circuit board with the output wires coded in what appears to be standard USB colours. My thinking is that if I cut the USB A plug off the extension lead I should be able to solder them to the board and (hoepfully) away I go, avoidning all the traffic.
The extension lead should be here in a couple of days - I'll let you know how I get on.
Trying to find out if there is such a thing as going from extmicro usb that the evo and flyer have to a usb type A (or any other normal usb).
Need a right angle to plug into tablet for car install and found that I can fit a microb angled cable into the tablet, but now need to take the car charges extusb and get an adapter to hook it all together.
You can just buy a regular micro USB extended cable. It fits in the flyer/view charge port.
Proprietary cable is the one on the right. Regular micro USB on left.
I am installing the tablet in dash of a car.
I have the oem car charger because its only one with right voltage. But I need a angled usb for clearance issues. So im trying to figure a way to go from the charger EXTMICRO usb to the angled usb.
Searched around and have come up completely empty.
I'm working on the same project and found this thread searching (again) for more info on extusb. The solution I came up with for getting enough clearance to use the port requires disassembly and if you plan on keeping the warranty, it's probably not a good option for you.
Anyway, my solution was to make some small right-angle brackets for the pcb that contains the extusb port. It requires material for the angle brackets and two small screws with nuts. See attached for a better idea.
I actually got the tablet installed and fairly well, but have since removed it to come up with better designs for charging, access to the power button (and possibly volume buttons) for recovery actions, turning the screen on/off with ignition, and potentially microphone relocation.
You may want to check out http://www.dealextreme.com/ for right-angle and other adapters if you don't want to open up the tablet.
PS: Protect that screen. The plastic is very soft and will easily scratch.
I don't follow.
I thought the HTC car charger was a plug with a USB port in it just like all the others. I thought this might help, but I probably have no idea what you're really looking for
http://www.amazon.com/Cables-Go-Right-Angled-Micro/dp/B005EV2LAM
If you *need* to use the 12pin micro usb that the view has (which from my understanding was only there for the docking station utility), then you might be out of luck unless you can build something yourself.
Im looking for a cable like you linked to, but then I need a way to connect the flyers car charger special usb tip into it. Only way I can think of is to carefully grind the corners so that it will fit into a micro B female connection.
But the chargers are not cheap and if I F*** it up Im out $30
On a kia soul forum where others are planning on doing the same install with the flyer, one guy has come accross a company that makes custom cables. He said that if We send the car charger to them they will replace the usb tip with a micro B 90 degree angle for $25.
So A person is sending the charger to them to have it done and is going to let us know how it comes out.
jacobbones, can you provide a link to the kia soul flyer thread?
Yes, here it is.
http://www.soulhamsters.com/forum/i...ale-again-24feb-7-android-tablet-199-shipped/
Talk about the custom job is near the end of the posts
opening up the car charger and replacing the cable is incredibly simple. I have done it so many times, I can probably do it blindfolded. I actually had to go and replace the OEM chargers cable with the USB cable that it came with because my damn dog chewed threw the charger cable. Didn't come back very pretty, but it works, that charger has got the be the best charger built I have ever seen, incredibly difficult to open, but I'm sure the car charger is a lot easier to open, you just need a soldering gun and it should be easy.
Sent from my ADR6425LVW using xda premium
First off I'd to say hello from Alaska,
Ok this may sound strange but does anybody out there know where i might find or have one made, I'm looking for a cable with 2 40 pin connectors on both ends, 1 male and the other female. This is for my TF201 and dock, I would use it so I don't have to take off the case to the Prime just plug in to the prime and to the dock..
Thank you all Stan
Cables to Go should be able to do this for you. I've had them make custom cables for me before. It likely won't be cheap, but they should be able to do it.
www.cablestogo.com
Just in case anyone was curious, I thought I would try to get lucky and see if a female-female USB adapter with a standard ASUS 40-pin cable on either end would work. However, it was only a novel attempt and the tablet does not recognize the dock as I had hoped.
I am sure Cables-to-Go could get something to work, but I agree that it will be quite expensive. It would be nice if there was a jumper cable accessory to accomplish this same concept since I am in the same position as the OP and typically carry the tablet in its own case and only use the dock when I have alot of typing to do.
On a side note, I did confirm that my Logitech Anywhere Mouse with the Unifying Receiver does work 100% with my tablet and Dock!....I just may be able to leave the laptop at the office yet!
Does anyone have a mapping of the pins and wires? I would like to try and "splice" two cables together to try and make a jumper cable but would need to make sure that I make the right connections. Any assistance would be greatly appreciated.
I don't think that's going to work for several reasons.
First and foremost, if use two TP USB cables as the souce of the parts, you'll end up with a "jumper" cable with male connectors at both ends. You need male to female, remember?
Secondarily (and almost as important) is the number of contacts on the USB end of the cable. USB has four conductors plus shield and nine conductors plus shield in USB 3. Taking a cursory glance at USB plug on my TP cable, that's all there is. I don't see any additional conductors.
Following this, it's EXCEEDINGLY unlikely that the cable has 40 wires (one for each pin on the Prime end) running the full length. If it did, where would they connect to on the USB plug? Kinda silly to include extra copper to go nowhere.
Instead, if you were to pry open the 40 pin male plug, you'll see that most the pins aren't connected to anything. They're not needed for the USB cable.
Sorry to say, this just isn't going to work.
If you do choose to clip one of your cables just to have a look-see, cut the cable somewhere in the middle. If you cut right up next to the USB plug, you won't have ample wire there to repair what you're about to break.
I am aware that you will need a female adapter to make a true "jumper" cable. However, there may be a way of jerry-rigging a connection to the dock if a female connector can't be found (I have yet to find a part online).
My question is more in regards to whether or not anyone had a schematic of which of the pins are connected to which of the respective USB pins so that I could determine the best way of making a connection....short of having a cable for the ASUS TF201 like this: iPhone Extension Cable
Hi!
Background:
I'm an esport producer and after some nightmare productions I'm really excited about the rog phone as it seams to be the only phone that have the features needed to make it into a good esports phone (e.g. Having 8-10 players competing in from of an audience), mainly: Hdmi output, ethernet capabilities and usb-c ports on the side..
Problem: After first successfully testing out Hdmi + ethernet connection I wanted to try if I could use the fan accessory and still be able to get the Hdmi signal from it.. When I connected the fan it told me to update the fan firmware so I did, but after that I'm not able to get Hdmi signal either with or without the fan accessory.. For instance, when I plug in my portable asus laptop monitor (power and signal from usb-c) the monitor starts to boot up and then dies.. Then tries again and dies and so on.. On my Samsung s8 it works fine.. So I'm guessing the firmware limits the power that the phone can output on the usb-c port.
Question, has anyone else experienced this issue? Is there a way to uninstall the fan firmware update (that obviously did not only affect the fan but the phone as well). The Hdmi adapter I used was something very similar to the professional dock but is actually an usb-c dock ment for laptops..
Tl:dr; hdmi doesn't work after "fan firmware update", plez halp.
Best regards
Ludvig Fjell
Qruxel E-sports Studio
Just a small update,
I was able to get it to work if I disconnect the power cable from the USB-C dongle and then connect it again.. and sometimes it also requires me to disconnect the HDMI + reconnecting that as well.. so I'm not sure if this actually was due to the fan firmware or just a result of a... weird bug(?) when it comes to the OTG features of the phone.. because connecting the dongle with both HDMI + power already plugged in does not work.
Anyway, just wanted you guys to know that it does work, just need to randomly connect/disconnect cables from the dongle first =)
Best regards,
Which USB-C to HDMI adapter were you using? I am looking for one that works with this device, aside from the fairly costly pro dock.