Help.
I think i bricked my photon.
I flash it using RSDLite. When entering BP Passtrought status, its failed.
And now it stuck on motorola screen. Can not enter RSD protokol or Fashboot. Just stuck on motorola screen.
I i can do, or its hardbrick and can not be revive ?
What have you done to uour phone?
flashed 2.3.5? pull the battery and put it back. Then press volumn up and power button at the same time. See if it can boot into rsd mode , if can't, I.m sorry.
Sent from my MB855 using XDA App
dxl880517 said:
What have you done to uour phone?
flashed 2.3.5? pull the battery and put it back. Then press volumn up and power button at the same time. See if it can boot into rsd mode , if can't, I.m sorry.
Sent from my MB855 using XDA App
Click to expand...
Click to collapse
I flash 198_7 because mine 198_6.
Trying pull and put battery, at first no hope.
Then i try connect to my PC, try to enter RSD protocol, and yes, it can enter RSD protocol again. I think it failed when on BP Passtrought because cannot detect driver.
Second try to flash it, it work.
Thanks for help.
Related
I'm stuck.
I cant get into RSD mode cause when I hold vol up it just goes into fastboot.
IF I vol down it just blinks and turns off...
What are my options.
Pull the battery then try to boot it normally, after a minute or so it goes into rsd mode
Sent from my DROID X2 using xda premium
Do you know how to go into android recovery and do a factory reset?
KurioHonoo said:
Pull the battery then try to boot it normally, after a minute or so it goes into rsd mode
Sent from my DROID X2 using xda premium
Click to expand...
Click to collapse
Its just sitting at "Failed to boot 1"
bijan588 said:
Its just sitting at "Failed to boot 1"
Click to expand...
Click to collapse
Try pulling the battery and put it back in with the phone off plug in your wall charger and see if your recovery comes up
What were u trying to do before this happened?
*****Have u tried a fully charged battery?*****
failed to boot = sbf time
no big deal
skwoodwiva said:
failed to boot = sbf time
no big deal
Click to expand...
Click to collapse
U can't sbf if u can't start rsd protocol
my bad
wow do we have a real one?
if I remember well it would always say failed to boot 2 and rsd would be available .
Is this a Dx2?
Apparently he is getting a failed to boot 1 ..I think I remember seeing this before.
It might be in one of the.older sbf tutorial threads...myabe the one by dag425.
It would be helpful (maybe) to know what was being done that caused this to happen.
Hopefully he wasn't messing with bootloader partitions and signatures or something. I think that would he just about the only thing that could hard brick us.
Sent from my DROID X2 using XDA App
Could it just be hardware failure?
We wont know anything til the OP comes back and give more info on situation
Going back to the original post... Since when did we hold volume up to get to android recovery??? Pressing up selects the option thats on the screen...
from my X2 roaming the north
LordRalh3 said:
Going back to the original post... Since when did we hold volume up to get to android recovery??? Pressing up selects the option thats on the screen...
from my X2 roaming the north
Click to expand...
Click to collapse
I'm assuming he meant power+up.
Sent from my MB870 using xda premium
If u hold power and volume up it takes u directly into "starting RSD protocol "
it is the method I have ALWAYS used when flashing sbf
I am stuck here too! I only have two options:
1: fastboot
or
2: nvflash
I have no idea what the hell eather one does so any little help is greatly appreciated for this noob. Thanks in advance...
So I take it yours says "failed to boot 1" also?
Is this Dx2 or mx2?
And you are familiar w/ booting menu: pwr on wait 1/2 (or less) sec then vol down and keep selecting w/ vol dn then vol up to select . Rsd is last.
IDNK WHAT BUT A REAL BRICK!
skwoodwiva said:
So I take it yours says "failed to boot 1" also?
Is this Dx2 or mx2?
And you are familiar w/ booting menu: pwr on wait 1/2 (or less) sec then vol down and keep selecting w/ vol dn then vol up to select . Rsd is last.
IDNK WHAT BUT A REAL BRICK!
Click to expand...
Click to collapse
yeah thats what i used to get to android recovery and rsd protocol and stuff. this time i can only do fastboot and nvflash. i am also stuck at the failed to boot 1 on boot. Also, it will only turn on when connected to pc/wallcharger...thank you for helping as my problem is the exact same as his. any more info needed just ask. i will try to reply quickly and fix this for both of us
Edit: this is dx2
trevsl
I don't know how to help but what exactly did you do to get the FTB 1?
skwoodwiva said:
trevsl
I don't know how to help but what exactly did you do to get the FTB 1?
Click to expand...
Click to collapse
was messing with settings in BSR idk what it was:
eather
1. clean boot files or whatever
or
2. partition sd card
i think it was the partition sd card part. cuz after that the option to go back went away...very odd. did a batt pull and then got failed to boot 1. i think im gonna have to take it to vzw and hope the guys an idiot
I just flash from RSD lite... and it's fail.... (maybe because of low battery power)
I already recharge the battery full using external charger...
But now... mu photon Bricked.. I can't start the RSD mode (Power + Vol Down)
is there still any chance for it?
Thanks b4
Have you tried power + up? Does it give you any options when trying it? And are you in a boot loop or stuck at dual core screen?
Sent from my MB855 using XDA
hyem said:
I just flash from RSD lite... and it's fail.... (maybe because of low battery power)
I already recharge the battery full using external charger...
But now... mu photon Bricked.. I can't start the RSD mode (Power + Vol Down)
is there still any chance for it?
Thanks b4
Click to expand...
Click to collapse
Can you describe what the phone does? Does it turn on?
Sent from my Photon
I believe, the RSD mode is [Power+Vol Up].
In any case, take out your battery and reinsert it.
Press [Power+Vol Up] as soon as you insert the battery.
Report back on what happens.
Spmeone has tp unlock the boatloader for 2.3.5 in order to go back to sprint sbf. I woulnt get my hopes up if i were you
melon69 said:
Spmeone has tp unlock the boatloader for 2.3.5 in order to go back to sprint sbf. I woulnt get my hopes up if i were you
Click to expand...
Click to collapse
? What? Unless I missed something I never recall op stating anything about flashing 2.3.5. Anyway, any progress on getting phone into RSD?
Sent from my MB855 using XDA
Try this step.
1. Connect your photon and PC/Laptop.
2. Press RSD protocol (volume up + power)
See if this work.
Was i has same problem, failed when flashing using rsdlite (when entering bp passthough), when try to enter rsd protocol, its just stuck on moto logo. But when i try to connect it with pc/laptop and try again entering rsd protocol, its work.
Hello, I am new to this forum.
I will try to explain the best that I can about how I got into this situation.
I was previously running on ICS 4.0.4(don't really know if it is .211 or .214 or something.). I tried to root it using Matt's Droid Razr Utility 1.7. I didn't really know what to do and was stupid enough to follow the video in the help thread(which was for upgrading from GB rather than rooting an ICS). Then I panicked.
I used option 1, followed by option 9, followed by option 3, followed by option 2, and then all four in random orders. Later on, I realized that I had to recover from the .211 file in the sd card after option 1(failure on my part). However, now whenever I try to enter recovery, I get Invalid Flash Mode Boot failure, whereas a normal boot will give me Invalid Flash Mode Flash failure.
I tried to use ADB tools and it didn't work.
Then I tried Utility 1.81. My driver is the same as the one provided, and the cable is the one that came along with the charger and phone.
My phone carrier is Singtel.
Any way out of this? Thanks in advance.
is it possible to enter fastboot ??
if so try to grab an image in development section wich you can place on your phone with RSD lite.
misterx11 said:
is it possible to enter fastboot ??
if so try to grab an image in development section wich you can place on your phone with RSD lite.
Click to expand...
Click to collapse
I can enter fastboot, and only fastboot. Attempting to enter any BP or recovery will result in the failures.
I just downloaded a stock rom for my phone. I'll see how it turns out.
Thank you for your time.
im in a similar situation, my phone is bricked, how do u enter fastboot? and where can i get a rom to use in rsd lite?
rageofshadow said:
I can enter fastboot, and only fastboot. Attempting to enter any BP or recovery will result in the failures.
I just downloaded a stock rom for my phone. I'll see how it turns out.
Thank you for your time.
Click to expand...
Click to collapse
chip0 said:
im in a similar situation, my phone is bricked, how do u enter fastboot? and where can i get a rom to use in rsd lite?
Click to expand...
Click to collapse
Do yall have XT910 or XT912 i.e. GSM or CDMA...
circleofomega said:
Do yall have XT910 or XT912 i.e. GSM or CDMA...
Click to expand...
Click to collapse
Since the thread name is Droid razr i think it is xt912
Go fast boot (power off your phone[if you cant then push and hold vol down+vol up and power button the same time, when you see your display flashed quickly release all buttons and press them again and hold- you should get boot menu and then use vol down to get on AP fastboot and use vol up to select it]).
Then use rsd lite and FXZ files to get your phone running, no need for any kind of wipe after this. Wait until rsd lite says finished.
What fxz files do I use? I've tried like 3 different ones and they always fail
Sent from my DROID RAZR using xda app-developers app
I am using RAZR XT910.
Recently, I have installed a wrong rom.
Now, when I switch on the phone, it only shows the MOTO logo then a blank screen.
When I connect to PC, only does the LED turned on.
Nothing happened when I try to pass power+vol up+vol+down
So, in the other word, I can't enter boot loader mode nor recovery mode.
While I was using RSD lite, RSD can't recognize the phone.
What can I do?
Can anyone help me. I can't use my phone now!!!:crying:
Ya need to press vol down and vol up at the time and then power button.
Please hit that thanks button if i helped ya
anurag.dj2u said:
Ya need to press vol down and vol up at the time and then power button.
Please hit that thanks button if i helped ya
Click to expand...
Click to collapse
But i tried nothing happened
Did you try connecting the charger when the phone is off?
Does it show the charging battery animation?
Charge it fully and then try power+vup+vdown.
I got into this boot loop once but RSD Lite recognised the phone.
Sent from my Nexus 7 using xda app-developers app
nijom said:
Did you try connecting the charger when the phone is off?
Does it show the charging battery animation?
Charge it fully and then try power+vup+vdown.
I got into this boot loop once but RSD Lite recognised the phone.
Sent from my Nexus 7 using xda app-developers app
Click to expand...
Click to collapse
I once successfully boot into boot loader, but when I choose AP mode, it only hold for a short period
RSD can't recognise as well.
It can show battery animation, i mean the animation which show the current battery percent!
Thx
Arthur Wong said:
I once successfully boot into boot loader, but when I choose AP mode, it only hold for a short period
RSD can't recognise as well.
It can show battery animation, i mean the animation which show the current battery percent!
Thx
Click to expand...
Click to collapse
Do you have motorola drivers on your PC without them RSD cant recognise phone. You can find everthing there http://forum.xda-developers.com/showthread.php?t=1539192
My device is: Motorola atrix 4g mb860 AT&T.
I used my phone as usual, and it seemed it went out of battery (possibly), when I tried to power it up it said:
"Failed to boot 2
Starting RSD mode" and got stuck, however, if I take out the battery and try to power it up again it will show the same issue, I cant enter the fastboot protocol support if powering it up while holding the volume up key, it just stucks, I cant either enter the selection of modes if powering it up while holding the volume down key way, it brings me to a black screen.
Ive read about this RSD Light and stuff, tried to flash 3 different sbf files, or more, after trying to flash it shows this in the device:
"Failed to boot 2
Starting RSD mode
sec_exception febe 35, 35", the phone get stucked, and in the program it says "FAILED" under the tab "Result", however, it happens only after the status of the phone in the program "Waiting for re-enumeration" changes to "Failed flashing process. Phone[0000]; Phone did not re-enumerate after RAM-downloader was sent. (0x703E)".
When i take the cable of the phone out and do a restart to it, I'm back to the first problem at the beginning, Failed to boot 2, Starting RSD mode.
It seems someone had a samiliar problem to me, but he used clocked and stuff... his thread:
http:/ /ww w.atrixforums.com/forum/rescue-squad/6164-se-flash-olympus-help.html
DELETE SPACES.
Waiting for answers, thanks anyway, and have a good day, Matan.
Sorry mate,sounds like a soft brick.
you can try flashing a stock SBF
Well can you help me with this?
BoriDe said:
Sorry mate,sounds like a soft break.
you can try flashing a stock SBF
Click to expand...
Click to collapse
well, then can you help me get these files? i used mine SBF files and didn't worked, maybe yours will.
I'll try your SBF files if needed.
mtnjustme said:
well, then can you help me get these files? i used mine SBF files and didn't worked, maybe yours will.
I'll try your SBF files if needed.
Click to expand...
Click to collapse
I´m in the same problem here, did you get out of this trouble ?
iddpioneer said:
I´m in the same problem here, did you get out of this trouble ?
Click to expand...
Click to collapse
Search das8nt on yahoo or something, you'll find it. Or just simply run a search for atrix sbf instead of being lazy
Sent from my MB860 using xda app-developers app