Hi, ima new member... i have a prob with my motorola xt800w.. it won't enter into bootloader mode, only in android recovery mode 3e.. i was using the phone to watch youtube videos. i noticed that it was getting slower so decided to restart the phone.. after i restarted the phone, it got stuck on the motorola M logo.. entered into recovery mode, inserted the usb but can't be detected by the pc.. i tried wiping delvik cache/factory defaults a number of times but to no effect.. much help is appreciated.. thanks!
oh, and i recently upgraded it to MIUI firmware which said that it was for moto xt800w but when i checked the phone status, it said motorola milestone.. i was a bit confused but didn't bother to change it since the phone was working well at first after upgrading it..
Use google translate to view this page: http://bbs.hiapk.com/thread-1242662-1-1.html it may help...but i also can't get bootloader by pressing the key, try to look this page if success tell me.
This worked for me,just needed to understand the rough translation of google translate
Try this key combination
Turn it off completely.(e.g. by removing the battery)
Half-press the camera button (as we do to focus while taking some snap). Then the Vol_Down key with that. Now press the power button.
The phone will get into bootloader mode.
help me motoglam xt800w
hi, help me please
my motoglam xt800w is not update to rom 2.2.2; it go to restart and restart apter i use RSD lite 6.1.5 to update rom 2.2.2
laovodanh said:
hi, help me please
my motoglam xt800w is not update to rom 2.2.2; it go to restart and restart apter i use RSD lite 6.1.5 to update rom 2.2.2
Click to expand...
Click to collapse
- Have you tried to wipe dalvik cache, cahe partition & factory reset before flashing it to 2.2.2 rom? Try it and flash it again one more time! That works for me!^^
Related
hi everybody I am new here and using atrix 4g and I need help I was update my att atrix 2.3.4 official gingerbread and today my phone is always restarting not opening . red motorola logo passing and att logo came then restart itself always doing this not giving any error . I can enter the fastboot menu and try to make android revovery but not working what is the problem do you know ? the phone heating
my advice:
try wiping data/cache first... if it doesn't help -> pull battery off... wait 2 minutes... put it back, power on in RSD mode (volume up + power)... flash official AT&T 2.3.4 SBF (if you don't care about unlocking or modding).... wipe data/cache...
Click to expand...
Click to collapse
I solved with wipe data option thank you so much
Hello everyone, this is my second post in the community and as above, I draw you before the serious problem that has my cell phone and that despite the help of all of you still not solved enclose descriptions videos and fails the steps and followed over time. :crying::crying:
All this happened when installing from retail jb rom ics one Chinese, after the installation the cell began to discharge too fast to the point of completely unloaded and not turn over, the next thing was wired switch it could enter the factory and then recovery only restarted.
after the above procedure to unbrick with Unbrick method & switch to 982.124.14.XT910.Retail.en.EU with which obtube not any response, after that a user community graciously offered to assist and I sending the same procedure but with the files for my region (Latam) after that the phone showed the motorola logo and restarted but at times passed motorola logo and showed the animated logo motorola, encendia the lights cell buttons and screen bottom came out "Wait a minute" restarted (enclose one. rar with videos of procedures performed and detailed information.
I count on your help and already thank you very much for reading my topic and I hope to get my phone I need too :crying:
:victorydt: my apologies for the bad drafting but all this is performed with English translator (I'm from chile) :laugh::laugh:
Hi,
Based on your video, I haven't see you flashed with RSD Lite and fastboot file.
You can give a try based on this thread:
http://forum.xda-developers.com/showthread.php?t=2231289
Download LATAM fastboot file (Chile should be latam right?) and download also latest rsd lite ver 6.1.4
Good luck and hope it will unbrick your phone.
idwijayaku said:
Hi,
Based on your video, I haven't see you flashed with RSD Lite and fastboot file.
You can give a try based on this thread:
http://forum.xda-developers.com/showthread.php?t=2231289
Download LATAM fastboot file (Chile should be latam right?) and download also latest rsd lite ver 6.1.4
Good luck and hope it will unbrick your phone.
Click to expand...
Click to collapse
reaches the motorola dual core logo and restarts :crying::crying:there some method other than by fasboot?, or some solution?
Have you download fastboot files that match with you region? if yes then you have same issue with me
So far what I know to flash is use batch file that developed by awesome developers here and RSD lite.
Have you try this:
- Go to boot menu (the way you get AP Fastboot menu) but this time try to select BP Tools
- and wait will your phone able to boot into system or not... If you able to boot into bp tools, get your phone root (JB is able for root now, get the thread in development), then install BMM to have it normal boot .. I got this suggestion but never able to have my phone boot in BP Tools, so I never know this works or not so good luck
- When you choose BP Tools and your phone still on M logo turn it off (you should wait only 10 or 15 minutes max) then turn off your phone and put it in boot menu to select BP HW Diag.. then.. we have same issue.. be prepare your phone only able to phone call , sms , taking camera, cannot access data only rely wifi , USB debugging not working, some fastboot files makes your phone not able to charge (I have to turn off my phone then charge)
I still strugling to have my phone back to normal also..
idwijayaku said:
Have you download fastboot files that match with you region? if yes then you have same issue with me
So far what I know to flash is use batch file that developed by awesome developers here and RSD lite.
Have you try this:
- Go to boot menu (the way you get AP Fastboot menu) but this time try to select BP Tools
- and wait will your phone able to boot into system or not... If you able to boot into bp tools, get your phone root (JB is able for root now, get the thread in development), then install BMM to have it normal boot .. I got this suggestion but never able to have my phone boot in BP Tools, so I never know this works or not so good luck
- When you choose BP Tools and your phone still on M logo turn it off (you should wait only 10 or 15 minutes max) then turn off your phone and put it in boot menu to select BP HW Diag.. then.. we have same issue.. be prepare your phone only able to phone call , sms , taking camera, cannot access data only rely wifi , USB debugging not working, some fastboot files makes your phone not able to charge (I have to turn off my phone then charge)
I still strugling to have my phone back to normal also..
Click to expand...
Click to collapse
did not work :crying::crying: still coming to dual core logo and restarts, other help......
Esto.Vir said:
did not work :crying::crying: still coming to dual core logo and restarts, other help......
Click to expand...
Click to collapse
Reflash the appropriate fastboot once again and then reboot into stock recovery and do fill wipe data and chaches . It may fix ya problem
Thx
Hit the thx button if i helped ya in anyways
anurag.dj2u said:
Reflash the appropriate fastboot once again and then reboot into stock recovery and do fill wipe data and chaches . It may fix ya problem
Thx
Hit the thx button if i helped ya in anyways
Click to expand...
Click to collapse
and tested with the brazil retail rom, fido, rogers ye had the same problem, my question is, if all the rom's the same that another problem will have my phone? , I can enter the ap fastboot recovery and all that d the stock recovery, my phone stayed brick to install a Chinese jb rom this tutorial :
http://www.chileandroid.com/t16992-romxt910jelly-bean-jelly-bean-41-2-china-retail-oficial
, Change kernel and everything that goes in the guide, that will be a problem? I hope you can help me from now thank you very much:crying::crying:
Hello there. Since I'm new here I'd like to say hello to everyone
Today I got my RAZR and wanted to play with it. It was already rooted and it had a 4.1.2 android for it, but I didn't liked it at all so I tried to install MIUI. After creating a new partition (1) i had installed miui, but after reboot phone died - Motorola logo appears and it reboots. I looked for some info in the internet and I found about installing new, clean rom via fastboot. I downloaded SPDREM_U_01.6.7.2-180_SPU-19-TA-11.6_SIGNEuropeAustraliaEMEA_USASPDRICSRTCEE_HWp2b_Service1FF_fastboot archive and tried to install it with Eternity Project, but after rebooting system does not start and android with red triangle appears.
Right now I am stuck and I don't know what to do. Could you guys tell me what should I do? The phone is RAZR XT910 from European distribution. Also, my Phone is being recognized as Spyder S.
Thank's in advance
Maciek
maciekk600 said:
Hello there. Since I'm new here I'd like to say hello to everyone
Today I got my RAZR and wanted to play with it. It was already rooted and it had a 4.1.2 android for it, but I didn't liked it at all so I tried to install MIUI. After creating a new partition (1) i had installed miui, but after reboot phone died - Motorola logo appears and it reboots. I looked for some info in the internet and I found about installing new, clean rom via fastboot. I downloaded SPDREM_U_01.6.7.2-180_SPU-19-TA-11.6_SIGNEuropeAustraliaEMEA_USASPDRICSRTCEE_HWp2b_Service1FF_fastboot archive and tried to install it with Eternity Project, but after rebooting system does not start and android with red triangle appears.
Right now I am stuck and I don't know what to do. Could you guys tell me what should I do? The phone is RAZR XT910 from European distribution. Also, my Phone is being recognized as Spyder S.
Thank's in advance
Maciek
Click to expand...
Click to collapse
When you see android with red triangle just press vol- and vol+ and find the option factory reset.
From your post I see that you flashed ICS Fastboot file,right?
Were you on ICS or JB before brick?
Sent from my Razr XT910
Well, as far as I remember it was JellyBean. I tried to flash it, but it didn't work at all. When I tried to flash the newest available soft for my RAZR it didn't want to flash (it was stopping at 1st step - when using RSD Lite, but when I used EPRJ flashing method, after reboot phone couldn't find any files copied to it's cache or something). Right now my battery is too low and I guess the only option is to make a factory cable, because it won't even charge.
And factory reset doesn't change anything: still the Motorola logo appears and then the phone turns off and sometimes reboots.
Is there any way I could install system via install update from sd card option? Or the only thing I can do is to try to install clean Android via RSD or EPRJ?
maciekk600 said:
Well, as far as I remember it was JellyBean. I tried to flash it, but it didn't work at all. When I tried to flash the newest available soft for my RAZR it didn't want to flash (it was stopping at 1st step - when using RSD Lite, but when I used EPRJ flashing method, after reboot phone couldn't find any files copied to it's cache or something). Right now my battery is too low and I guess the only option is to make a factory cable, because it won't even charge.
And factory reset doesn't change anything: still the Motorola logo appears and then the phone turns off and sometimes reboots.
Is there any way I could install system via install update from sd card option? Or the only thing I can do is to try to install clean Android via RSD or EPRJ?
Click to expand...
Click to collapse
The only way is to flash it with RSD Lite.
Here http://forum.xda-developers.com/showthread.php?t=2231289 are all JB Fastboot files.
Sent from my Razr XT910
Okay. I downloaded the british retail soft, we'll see if it works. But will this soft have Polish language?
And the second thing: is there any way to charge the phone when in my situation? When I plug in the charger, white led only flashes for a while and then the bootloop starts - motorola logo appears and that is all. I have also tried the method with pressing vol + and - for 10 seconds and again, but this didn't work either. The only exit here is to make factory cable, right?
maciekk600 said:
Okay. I downloaded the british retail soft, we'll see if it works. But will this soft have Polish language?
And the second thing: is there any way to charge the phone when in my situation? When I plug in the charger, white led only flashes for a while and then the bootloop starts - motorola logo appears and that is all. I have also tried the method with pressing vol + and - for 10 seconds and again, but this didn't work either. The only exit here is to make factory cable, right?
Click to expand...
Click to collapse
Right,with factory cable you can't charge the phone but you can flash fastboot file,that's what it's for.
Sent from my Razr XT910
It worked, thank God. Thanks for the advice, next time I'll be more careful with my RAZR
Greets!
But another problem suddenly appears - my battery won't charge over 40%. Tried turning it off, but it didn't work.
Edit: I have had 50%, now I have 60. It looks like it's going up and changes after 10%. We'll see if it manage to charge up 100% battery.
Edit2: Okay, it fully charged. Thank's again mate for tips
I've search long and hard ..to no avail. I have a huawei ascend d1 qaud u9510e. Its had a chinese custom recovery and was flashed with MIUI 3.2.22. From the UPdater miui i've been spammed by to do a 'weekly update'' on a daily basis. I read it , it said it didnt delete internal and minimum problem would happen. So I did it. It went through the install phone rebooted. it worked one time till I restarted phone. now i am unable to get back .All i see is the HUAWEI start up logo. it just hangs there. the phone wont turn off just restarts itself to that screen, I am unable to get to custom recovery by holding the power button + volume + which etc. I have the original miui 3.2.22 on my sd card but cannot get to that because of this bootloop/cannot access reovery mode. majority of the time my computer will not reogonize my device but sometimes my computer recognize my phone as adb. How Can I fix it so I can get to a recovery so I can reflash to previous working rom. thank you for your time
T2av said:
I've search long and hard ..to no avail. I have a huawei ascend d1 qaud u9510e. Its had a chinese custom recovery and was flashed with MIUI 3.2.22. From the UPdater miui i've been spammed by to do a 'weekly update'' on a daily basis. I read it , it said it didnt delete internal and minimum problem would happen. So I did it. It went through the install phone rebooted. it worked one time till I restarted phone. now i am unable to get back .All i see is the HUAWEI start up logo. it just hangs there. the phone wont turn off just restarts itself to that screen, I am unable to get to custom recovery by holding the power button + volume + which etc. I have the original miui 3.2.22 on my sd card but cannot get to that because of this bootloop/cannot access reovery mode. majority of the time my computer will not reogonize my device but sometimes my computer recognize my phone as adb. How Can I fix it so I can get to a recovery so I can reflash to previous working rom. thank you for your time
Click to expand...
Click to collapse
you must download U9510E B610 EMUI 2.0 by svikfromorel v02 for XDA search for this in the forum i cant post any link...
unpack, connect the phone to PC and run Flash_all.bat file
after ending a proccess don't forget do wipe data and wipe cache
huawei u9510e bricked
eldukex1 said:
you must download U9510E B610 EMUI 2.0 by svikfromorel v02 for XDA search for this in the forum i cant post any link...
unpack, connect the phone to PC and run Flash_all.bat file
after ending a proccess don't forget do wipe data and wipe cache
Click to expand...
Click to collapse
Hi, I am a newbie to flashing custom Roms. I desperately need help. I have the same phone and the same thing happened to me while trying to flash a ROM. My screen was stuck on huawei logo. Unfortunately, it happened in the middle of the high so by the morning the battery got drained completely. What are my options if any? Please help. I am willing to pay. Thanks a lot in advance.
Hello! I rooted my Coolpad E560, a.k.a. Coolpad or Sky Mini and everything was fine until I decided to unroot it. It immediately restarted and will not boot ever since (stuck at logo). I opened recovery mode and selected wipe data/factory reset but it didn't solve the problem, neither did wipe cache. Then I selected reboot to bootloader. "Download and Install the package? Press volume up to agree or volume down to cancel". I press volume up and then it's stuck on "Information Do not disconnect the data cable". In the end I tried to flash stock rom. The only firmware I found was (phone name).CPB and it seems like the only flashing tool that can use .CPB is YGDP. But the flashing process doesn't even begin, it gets stuck on Entering download mode... I unsuccessfully tried to enter download mode on my phone. It doesn't have removable battery, some key combinations I tried didn't work. Now I don't know what to do. Any help will be appreciated.
bump
bump
How did u solve it ?
Did u solve it ? do you have any backup files that u can send me ?
denico_bg said:
Hello! I rooted my Coolpad E560, a.k.a. Coolpad or Sky Mini and everything was fine until I decided to unroot it. It immediately restarted and will not boot ever since (stuck at logo). I opened recovery mode and selected wipe data/factory reset but it didn't solve the problem, neither did wipe cache. Then I selected reboot to bootloader. "Download and Install the package? Press volume up to agree or volume down to cancel". I press volume up and then it's stuck on "Information Do not disconnect the data cable". In the end I tried to flash stock rom. The only firmware I found was (phone name).CPB and it seems like the only flashing tool that can use .CPB is YGDP. But the flashing process doesn't even begin, it gets stuck on Entering download mode... I unsuccessfully tried to enter download mode on my phone. It doesn't have removable battery, some key combinations I tried didn't work. Now I don't know what to do. Any help will be appreciated.
Click to expand...
Click to collapse