There is a radar from UK. Sim-free. I decided to upgrade from 7720 to 7740 through the RUU, Windows 7, the process has started and reached 5%, then wrote the RUU error 226. On the Radar hangs 5%. After rebooting, Radar writes SPL version and bottom the factory reset. In the USB HOST mode does not go. Firmware is always up to 5% and then stops.
There are other ways to flash?
p.s. support htc offers to send the phone to a service center to England.
and this is called service??
upd 2012_06_13 I repair my Radar by Riffbox Jtag.
(ладно бы единичный случай, но я не первый с такой проблемой на радаре)
I have the same problem
Maybe if you turn off the battery, and disconnect the phone and then turn on, then he will enter the mode USB HOST. But this is only a hypothesis, but disassembled it is not so easy
Disassembly is easy, and I've already done the but there is nothing in ROM memory.
He Will enter into the USB HOST mode is not possible
FLAM7575 said:
Disassembly is easy, and I've already done the but there is nothing in ROM memory.
He Will enter into the USB HOST mode is not possible
Click to expand...
Click to collapse
bad news. wait for riff box support...
Anyone knows a fix for this ? Tried to flash 2.01 but it hangs at 5% and reports error.
FLAM7575 said:
Disassembly is easy, and I've already done the but there is nothing in ROM memory.
He Will enter into the USB HOST mode is not possible
Click to expand...
Click to collapse
Yes, Disassembly is easy
now charge battery from power supply unit
I do not know that you can try to disassemble the handset, but I'll try different combinations
and bad news again....
Any progress or solution here ? Mine is bricked now.
I created a group to somehow draw attention to our problem
http://www.facebook.com/groups/380137085339394/
I repair my Radar by riffbox jtag !!!!!!!! ))))))))))))
Related
Dear all,
I just got a Dopod 838pro, it seems totally dead as i can't turn it on, i can't make it enter the bootload mode. the only thing i can see is the LED is in red when i charge it.
does any one know what's the problem and how to fix the problem?
many thanks.
Try another battery if you know someone that has the same device. It could be bung.
Cheers...
ultramag69 said:
Try another battery if you know someone that has the same device. It could be bung.
Cheers...
Click to expand...
Click to collapse
yes i have put a imate JASJAM battery in it but the problem is still the same.
cheers.
seems no solution?
no simple solution
Hi tangwd898,
i got no simple solution but some advice.
First i have to quote myself form another thread :
This is very similar to what happened to my device. After downgrading from olipro's hard-spl something went wrong. After flashing succeeded with 100% the device got restarted and there it was... nothing!!
What i found out in the meantime is that the IPL was not flashed correctly.
While trying to reflash the device with JTAG debugger, i examined that the NAND write protect signal sticks to GND right after reset.
Maybe this also a hardware issue. I'll find out soon
The bricked IPL-bootloader could also be the cause.
At least if the red light turns on, the DC-DC converter on the hermes is doing well. This means the unit is partially working but not booting.
Click to expand...
Click to collapse
Check if your device is still recognized by a host PC.
If you are not able to enter bootloader and there's no green light at all when you power up the device, i would suggest to check your mainboard.
First do some measurements...
Follow this thread:
http://forum.xda-developers.com/showthread.php?t=316531
You may also try the JTAG method to examine your bootloader code or reflash NAND chip:
http://forum.xda-developers.com/showthread.php?t=391047
In any case you'll need some electric skills and follow the manual to disassemble the device!
Good luck,
scholbert
scholbert said:
Hi tangwd898,
i got no simple solution but some advice.
First i have to quote myself form another thread :
Check if your device is still recognized by a host PC.
If you are not able to enter bootloader and there's no green light at all when you power up the device, i would suggest to check your mainboard.
First do some measurements...
Follow this thread:
http://forum.xda-developers.com/showthread.php?t=316531
You may also try the JTAG method to examine your bootloader code or reflash NAND chip:
http://forum.xda-developers.com/showthread.php?t=391047
In any case you'll need some electric skills and follow the manual to disassemble the device!
Good luck,
scholbert
Click to expand...
Click to collapse
hi scholbert,
thank you very much for the information.
my unit seems NOT totally deal as i found it can be entered into the bootloader for about two second last night for a few times and dead again, but i can't make it enter the bootloader again now. very weird.
The unit can't stay for a long time when it entered the bootloader and will dead when i releaseed the key.
can anyone know how to do next?
many thanks.
Hi guys!!! Before start I want thanks all for all the commitment and the great work.
I follow this forum much but I write today because yesterday I kill my TG01 when I attempt to flash with WP7 with the tutorial that I link ( I cannot use Qinwengui tutorial because the link of WP7boot was removed ).
Hi think that the problem made from a problem when I open the archive that at the inside have the files to flash and, after I erase the nand, when in the next step I write the file occurred, an error with MIBIB writing appear, I try to replace it with no result, at the end, when I put back battery and replace I cannot turn on my TG01.... nothing to do............. is completly dead.
My battery is full (I measure it) only I can ask if there's a solution or if I found a Riff box can I repair this? And how?
Another thanks.
erasing NAND is dangerous do you have any sign of life at all on your tg01 any LED lights, screen ? try different button combinations ?
i did say flashing wp7 for a unexperienced member is not a good thing to do but never mind. report back if you get any LED lights or anything im no pro or anything but i will try my best to help you
I jonnyhall1bmx1, thanks for the quick answer, it's not my first time in flashing procedure, but this time I try this because i'm not at home at the moment of flash and i find only the file of tutorial that I haved link.
But..... no sign of life, is total dead, I try all the combination..... is total dead...
Do you know if riff nox can help me?
I see that situation is totally black!!!
hmmm im not 100% sure how a riff box works
and dont panic, ive had my tg01 doing nothing at all and managed somehow to bring it back to life haha
like i say im no expert i would like to help you but i can only fix a tg01 with LED lights im not sure what to do with it been dead.
your best option is to pm one of the smarter people like NOKSER although you would get an answer quicker out of a brick wall with him.
you could try MIRO, hes a great guy or any of the developers.
dont give up tho like i say my tg01 was once dead 3 times still always somehow got it running
Another thank, I wait if Nokser or Miro see this thread for some minute and after try to give a pm with the first post.
Seems to be real dead, when i put the battery recharger, not come out the orange led, i think now the phone not know to be a phone.
Thanks to all that can give me a help.
Bye.
RonnyRox said:
Another thank, I wait if Nokser or Miro see this thread for some minute and after try to give a pm with the first post.
Seems to be real dead, when i put the battery recharger, not come out the orange led, i think now the phone not know to be a phone.
Thanks to all that can give me a help.
Bye.
Click to expand...
Click to collapse
I not understand for end this problem, but if you not write completly nand parts(bootloader), then phone is dead... now only unbrick device in Riff Box.. or in any J-Tag
Maybe you write video from your screen phone...
Hi Nokser, thanks for your answer.
Ok if you see the tutorial that i use, i'm lock at this point:
Click erase,
when erase has completed click write.
At this point the led change various color but when terminate process give me a message like " MIBIB cannot write...etc...", I try to replace the folder with anothe zip download from another thread but with the same result.
When I disconnect the phone, put out the battery and after riconnect.
Result is a dead phone (completly off:screen and led and other ).
Do you know if in this state with riff box is possible to reflash the nand?
Thank you for all your hard work! Bye.
RonnyRox said:
Hi Nokser, thanks for your answer.
Ok if you see the tutorial that i use, i'm lock at this point:
Click erase,
when erase has completed click write.
At this point the led change various color but when terminate process give me a message like " MIBIB cannot write...etc...", I try to replace the folder with anothe zip download from another thread but with the same result.
When I disconnect the phone, put out the battery and after riconnect.
Result is a dead phone (completly off:screen and led and other ).
Do you know if in this state with riff box is possible to reflash the nand?
Thank you for all your hard work! Bye.
Click to expand...
Click to collapse
Maybe your battery is unloaded.
Riff Box J-tag re-write all nand partition, separate and spare.
Ok so you erased whole bootloader section and when writing it an error occured?
Then:
Riffbox only.
You can try to measure battery voltage with any voltagemeter but I think you killed it.
Thanks to all, yes I can rewrite all nand: Positive.
This is appen yesterday, i have just measured the battery is near to full.
No jtag, only Riff Box.
If I understand now I try to search a riffbox ( need any accessory? ) or search for someone that make this operation near my zone.
Thanks to all, if i have some notice i post it, if another one have another trick, please post.
Now i go to work ( night turn ) thanks for all!
RonnyRox said:
Thanks to all, yes I can rewrite all nand: Positive.
This is appen yesterday, i have just measured the battery is near to full.
No jtag, only Riff Box.
If I understand now I try to search a riffbox ( need any accessory? ) or search for someone that make this operation near my zone.
Thanks to all, if i have some notice i post it, if another one have another trick, please post.
Now i go to work ( night turn ) thanks for all!
Click to expand...
Click to collapse
Riff Box - This is a J-tag tool. This device, repair your phone. However, it is quite expensive.
Maybe you without battery, and wait 2-3 h. This device must rest. I had such cases more than once.
Hi Nokser, this morning I read your post and I try to put out the battery, after 2-3 hours I reconnect the battery with no results.
Now I buy the Riff Box, I think that after the NAND flash i try to sell it right to recover a part of money.
In another thread I see this your photo that I link under this post.
Is this connection the right connection with the Riff box?
And is this without any accessory ( only the cable )?
Always thanks, bye.
RonnyRox said:
Hi Nokser, this morning I read your post and I try to put out the battery, after 2-3 hours I reconnect the battery with no results.
Now I buy the Riff Box, I think that after the NAND flash i try to sell it right to recover a part of money.
In another thread I see this your photo that I link under this post.
Is this connection the right connection with the Riff box?
And is this without any accessory ( only the cable )?
Always thanks, bye.
Click to expand...
Click to collapse
You have bro all info in gsmhosting.com.
All news, method, etc.. or PM for me
Thank for the info, if I need help in the next day I send a PM to you.
I just wait the Riff Box, i think it comes to me in monday.
I see your site and I see some news, I wait for camera driver!!!
Thanks Nokser.
I guys.
Today I try to repair my TG01 but when I press resurrection I receive this error:
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.28, JTAG Manager Version: 1.37
Selected Resurrector: [Toshiba TG01]
Connecting to the dead body...OK
Detected dead body ID: 0x202400E1 - CORRECT!
Set I/O Voltage reads as 2.60V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...FAILED
ERROR: Wrong response code from the RIFF Box: 0x45
I know that other guys have the same problem, I have just verified connection and all the advice, who can help me?
Try as HD2
I found it in another forum, now I try this..... Very thanks!
Hi guys, I follow this instruction that I found in another forum, because my initial problem was that I erase the NAND:
Download full backup from this link :
http://rapidshare.com/files/42229365...ull_backup.rar
Connect phone to RIFF, go to DCC TAB, select HTC HD2.
Open full backup, and set following options :
- Start address: 0x0000000000
- Data Length: 0x0000800000
- Check "Image file is used"
- Check "Use address as offset"
- Select ROM1
Other options must be NOT Checked, click "Write". This will restore erased area in modem part.
After more test the only mode that give me the possibility to update is to short pad 1 and 3, turn on the phone and connect via usb: TG01 in Download Mode.
After this perform ROM upgrade using TG01 downloader.
Now I have the problem of Win7 x64 and the driver...
When I have news, I will write.
Bye and thanks to all have help me.
TG01 Return to life!!!
OK, now I have TG01 with WM 6.5 Nokser with Radio 0321.
A partial correction:
After the resurrection with Riff Box "not need" to short Pad 1 and 3, my problem was the battery is go down with the much try.
I make a recharge to much to have 3,7V and after with TG Downloader and Rom.bin of WM 6.5 I flash with success the phone .
For solve the Win7 x64 problem I install Virtual PC with WIN XP and execute all under this.
Now I still do a full recharge and this evening I finally can try WP7!!! ( Cross the finger... ).
Special thanks at Nokser and all the guys that give me a great help.
Thanks to all!!! Happy Christmas and Happy New Year!!!!
So .short story.i have a nokia lumia 800 rm 801,and dosn't boot anymore.i wen't to a repair shop and the guy over there said that the bootloader needs to be reinstalled because it's bricked,but he can't do it)
this is what's i've tried: leaving for few hours to charger/usb cable,didn't worked.
if i connect it to pc for few seconds i see in control panel,nokia dload and it discconect it.
i can start recovery mode( that windows phone with the computer cable thing on my phone if i connect the phone to charger or usb and press camera volume up and power) but i can't start recovery mode without data cable/charger.
when i connect the phone to charger it vibrate(nothing on the screen shows)if i press the power button for half a second i see the t-mobile logo.and keeps apearing and vibrating random times i guess i didn't counted exactly.(restart loop or something)
when i connect the phone to usb it vibrates long,and keep connecting to pc and discconecting.
when it's not connected to charger or usb,don't give any sparkle of life(no vibrating,powering on,nothing)
any help please?if anyone would be that kind to help me ,or give me enough advices to fix it by myself...
bump
noxified said:
bump
Click to expand...
Click to collapse
Ok, you also contacted me by pm and I'm trying to help you, but I don't have a Lumia 800 so I don't know all the difference between a Lumia 710 and a Lumia 800.
So in short, before I unlocked my phone I had a similar issue then which you are dealing now, what I did is disconnect the phone from the pc and pressed the camerabutton and keep it pressed, on the same time I pressed the on/off button once but keep holding the camerabutton, the phone shows the recovery mode, so I connected the phone with zune and reinstalled my backup, that's it.
(It's not neccesary to dis- and reconnect, but I only tell you the way I did it.)
If that doesn't work I think you must read this thread from bypx,
http://forum.xda-developers.com/showthread.php?t=1457341
Succesz,
and if i don't have the backup? cant i just use someone else's backup?(for nokia lumia 800 rm-801 ofcourse)
on that guide i don't have dead usb flasing...
and without dead phone usb flasing i get this error:
ERROR: OSBL reported an error! Code: 0x30022
and in linux if i connect it in recovery mode,it gives me this error:
unable to mount windows mobile error initializing camera: -105 Unknown model
and discconects automaticly from recovery mode,entering automaticly in that reboot loop.
i think that the bootloader it's faulty.
when i connecting the phone to zune i get this error: C101002E
And i don't have a backup for restoring...
Ok, I do some research and contact you asap
Greetz,
ok,i will wait.
bump
noxified said:
bump
Click to expand...
Click to collapse
stop bumping, pls. This won't speed up a solution!
if anyone has an idea, they will help you.
And i already told you via pm what i know.
i tought if i was bumping someone would see the topic ,who know how to do it.
ok,i have borrowed atf box.what's next?
noxified said:
i tought if i was bumping someone would see the topic ,who know how to do it.
ok,i have borrowed atf box.what's next?
Click to expand...
Click to collapse
If you think that you can do it by yourself, search the tutorial for unlock the phone with the ATF box. If not, do like me: go in a service center for phones, pay 13 euro, and in 30 minutes you go home with the phone done ok without any complications. I changed in service my bootloader from dload to qualcomm.
Sent from my HTC Desire HD
whiperhack said:
If you think that you can do it by yourself, search the tutorial for unlock the phone with the ATF box. If not, do like me: go in a service center for phones, pay 13 euro, and in 30 minutes you go home with the phone done ok without any complications. I changed in service my bootloader from dload to qualcomm.
Sent from my HTC Desire HD
Click to expand...
Click to collapse
I tryed at a service,money ain't a problem.The guy over there couldn't do it.
noxified said:
I tryed at a service,money ain't a problem.The guy over there couldn't do it.
Click to expand...
Click to collapse
Try on other service. IMO is a complicated procedure for an inexperienced guy.
Sent from my HTC Desire HD
i tried on 5 services...
Ok, this is as much a heads up to other P780 users as a desperate shoutout for help... I don't think I've seen anybody else with this problem so far, so here goes.
I purchased a P780 in december 2013, loved every bit of it and it worked flawlessly until about 1 month 1/2 ago. The phone was still brand new, but all of a sudden, it decided it will not charge unless I shut it down.
Basically:
- Phone powered ON, no charge, and not recognized when plugged into a computer => nothing happens. The funny thing is if I use the USB OTG cable, it will actually see and read USB flash drives...
- Phone powered OFF, will charge although the screen won't show anything, only the red led will let you know that it is charging. Also, it won't charge past 88%, meaning when I turn it off and charge it, the maximum battery % is 88% even if I let it charge for 2 days...
The phone has been like that for more than a month now... I considered sending it back for repair or exchange, given it's still under warranty but I am afraid to do so, since I would have to send it back to china and the seller who I bought it from won't help.
Ok, so what do you guys suggest I do? Do you think it's hardware related or software related? I am not sure it is hardware since it will actually charge albeit when powered off, and it will see USB flashdrives when using the USB OTG cable...
PS: I am running multinlingual S125 (Chinese P780).
The easiest solution is: Do a factory reset, if not working; Flash another ROM. Still not working? Sent back to service center, probably is hardware issue then.
Well that was my first reaction, when I first noticed it about 1 month 1/2 ago: I directly factory reseted it, which did nothing. I then proceeded to reflash the ROM (Multinlingual S125, Chinese base), which also did nothing. By the way, flashing was a bit of an ordeal since the tel would not be recognized when plugged into a computer. What I did was press Power + Volume Up, after launching flashtool and clicking on download or firmware upgrade. Only then would the computer recognize that something is being plugged in and start the flashing process. May be that info could help other people...
I proceeded to changing base to ROW P780 (using satanduck's ROW S123) a few days ago, in a last desperate attempt that it would change something, but alas... Really though, sending the phone back to China for repair scares the living f**k out of me, I don't even know how to proceed or where to begin...
Same here, i have charging problem with my p780. It wont charge with powered on, and only able to charge when switch it off. Been doing resets and flashes many time since then but nothing can fix my charging issue. Asked several times in local p780 forum including kaskus, also give no solution. I:ve read many complain bout lenovo SC in my country, make me think twice to take my phone there.
Sent from my Lenovo P780 using xda app-developers app
Same here
I have same problem. It's nice to know that phone will be recognized in recovery mode... so I can flash it.. since I have managed to damage its rom, so it wont boot. All in hope to solve this no-charging problem..
Still have same problem, even worse..
I have checked, unforunatly, my PC doesn't register my phone as any device when it's in recovery mode. With that said, I can't flash new rom, or recovery. Now I'm stuck with rom that doesn't boot, TWRP recovery that is incompatible with this phone (so I can't flash another rom), USB connection that makes phone unrecognizible by PC so I can't flash rom/recovery with flashtool..
I have gone to official Lenovo service here in Serbia, but since I have KIT (for China market) version of phone, there is nothing they could do to help. Pretty lame..
dario.alispahic said:
I have checked, unforunatly, my PC doesn't register my phone as any device when it's in recovery mode. With that said, I can't flash new rom, or recovery. Now I'm stuck with rom that doesn't boot, TWRP recovery that is incompatible with this phone (so I can't flash another rom), USB connection that makes phone unrecognizible by PC so I can't flash rom/recovery with flashtool..
I have gone to official Lenovo service here in Serbia, but since I have KIT (for China market) version of phone, there is nothing they could do to help. Pretty lame..
Click to expand...
Click to collapse
Try reinstall drivers for phone. Or try use another PC with different OS (win7 or winxp). Before your phone was recognized on your PC? Did you have installed drivers for phone before?
lenovo P780 Life 07 said:
Try reinstall drivers for phone. Or try use another PC with different OS (win7 or winxp). Before your phone was recognized on your PC? Did you have installed drivers for phone before?
Click to expand...
Click to collapse
I have read almost all topics regarding p780, and have found this post:
http://forum.xda-developers.com/showpost.php?p=52665841&postcount=16
That saved me... I have newer version of P780 that uses newer Preloader.img. That's why I couldn't flash anything. Now I still have that no charging while powered on problem, but at least I have 90% functional phone..
Leaked battery.
If anybody care to know why P780 has this problem. Driven by little madness I opened the device using mini screwdriver. Found lots off white crust on the right lower corner. I can conclude that mine has battery leaking problem which caused it loss 1/3 of its potential. A replacement need to be done by lenovo center.
Kevin Ismail said:
If anybody care to know why P780 has this problem. Driven by little madness I opened the device using mini screwdriver. Found lots off white crust on the right lower corner. I can conclude that mine has battery leaking problem which caused it loss 1/3 of its potential. A replacement need to be done by lenovo center.
Click to expand...
Click to collapse
Thanks for your info. I will check my phone in the morning. :thumbup:
Sent from my SMT TAB 704DC using XDA Free mobile app
Hi.
I tried flashing a rom on a H96 Pro Plus 3+32GB box with an Amlogic S912, chip.
First couple of times when i tried flashing, it went up to 3-4% and gave out an error. Then i unchecked the erase flash and erase bootloader options and it went to 8% and then gave out an error once again.
After a couple of tries with the erase bootloader and erase flash options. It succeded flashing. But when i plugged in the box. There was no picture, there was just a blue light on the box.
The computer won't recognize the box after that, i've tried putting a rom on a SDcard, i've tried shorting some pins, not sure if they were the correct ones, but no luck. There is power going to the box, the blue light is on, but it won't turn on or display any signal.
Please help!
Thanks in advance!
Hi if you just search u would find the answer faster than writing this thread
anyway
hopefully it will help
other wise you should give more detailed and explained info
mazjed said:
Hi if you just search u would find the answer faster than writing this thread
anyway
hopefully it will help
other wise you should give more detailed and explained info
Click to expand...
Click to collapse
Hi.
Trust me i've searched for a week without any success. Unfortunately the video didn't help me since my problem currently is that the box is getting power but there is no hdmi signal, nor the box is getting recognized by the pc after flashing the rom.
Thanks for trying to help.
then the only chance you have is the short method
mazjed said:
then the only chance you have is the short method
Click to expand...
Click to collapse
Hi
I tried shorting pins, like in the tutorial but nothing happened. Not getting recognized still.
Hi
Ok, so i've fixed the tv box and it turns out i was doing something wrong. I didn't have power plugging it in. I was relying on the usb connection to give enough power to the box. I've done this to get back the box. Please if you don't know what you are doing, get someone that really knows. I'm not responsible for any damage that may happen. This is just what i've done to recover the box.
1. Hold the reset button on the box
2. Plug in USB in the pc and in the box
3. Wait 2 seconds and then plug in power.
4. Hold the 5th and 6th pin (i think). Please watch the video andmake sure that you know what you are doing, since 1 bad move could render the box totally unusable. Thanks. you should hold the pins for a couple of seconds and it should pop up
Also i wasn't able to install Aidenrom (while flashing it gives out an error) or Atvexperience (it cant get imported by usb burning tool)
I reinstalled the default rom. And i was using USB Burning Tool V 2.0.8
Thanks for your help.