I flashed my tg01 with wp7 a long long time ago,been good until i decide to return back to wm .5 and pressed the soft reset button under my back cover.Then i turned it on and all it shows now it shows the wp7 connect to the computer sign
After that i connect the phone to the computer but heres the problem! it detects the phone (sometime it fails to install the usb driver) zune came up with a error code saying no restoration point unable to restore this device.When i open download mode(blue LED light) nothing appears on the screen.Am i screwed?do i have a chance?Help please!
No it is all OK. If you have blue LED you can go back, just leave it on usb or charger for few hours to be shure for battery then do the downgrade to wm 6.5 by Mirlog. You have link to totorial in his signature. Enjoy
Related
Hi Guys,
Need your advise, I've tried to reload the PDA Viet temp on my device so that I could reload the 4.0.0.6 ver again. The rom works great but some how on the 2nd day it start to be power draining on my 818Pro. was going to reload to play as plain before any apps installation to see if its apps issue and got stuck at boot loader.
Issue Now:
1. on running the device now it goes into boot loader and when connected.
2. doesnt seem to have any OS install and when Hard reset goes to bootloader too.
3.when try to load the ROMUpgradeUtility_NV_G4 fail to connect.
4. Now even when in Boot Loader Screen, the device goes on and off USB connection. making it impossible to transfer files to device.
Please Advise.
Thanks in advance
Try to push/hold camera, comm, and reset button, then release reset and comm but hold the camera, it will be go in the bootloader screen. At this point connect the usb cable and wait until the connection is done.
Are you sure your pda is G4?
thks some more light to the problem both hard and soft rests gives me bootloader but its turn on and off on the USB connection and last check on power is @ 90%
skyhigh75 said:
thks some more light to the problem both hard and soft rests gives me bootloader but its turn on and off on the USB connection and last check on power is @ 90%
Click to expand...
Click to collapse
Hi All,
Just like to encourrage all to be persistent on resolving the issue, think my issue had been resolve, not sure why the batt hard to be charge for bout 6-8hrs by Charger(not USB connection from Computer) almost like initial charge to be able to last through the step one downgrading to wm5.
Previously I charge for bout 4hr via charger and it didnt work, but since there's not new solution I persisted to charge for a longer time and rest before I try again and it work. Thanks for all's contribution the the solutions.
MY HP6815 IS DIED.
I was flashing with the good wm5 rom of NHOCBANME when the phone fell to the ground and has detached the battery!!!
My hp 6815 is off and doesn't turn on.
I tried to flash by ordinary mode but the phone is always off.
Only battery led is on if the phone is charging.
I think it is permanently damaged.
Can someone help me?
Test:
1 - Remove the batery...wait some secounds
2 - Put the batery back on it
3 - Press POWER
4 - Press RESET with stylus and press the 2 softkeys (the keys that are on top of the red and green buttons)
5 - The phone will enter flash mode
6 - Use software to re-flash or use SD card to do it(SD card option: card must be inside when you do this!)
The same thing happened to me... but i lifted the cell and there was no cover in the battery...
hope this helps...
Dead boot ?
Hello,
I have a same problem after flashing. No life in my 6815.
The LED used to blink orange when charging or usb connected but now it flashes orange-green. Does anyone know how i need to fix my boot with jtag or other fix?
Many thanks
A free TUROK game[Newest turok game out last year] for whoever helps me fix my bootup. Game is boxed, manual etc.
Thanks to GraeFNZ (and helloworld1)...This is the correct procedure:
" How to recover from semi-brick state:
1. Prepare a sd card with proper diskimg.nb0.
2. Pull out the batter for a few minutes.
3. Press and hold two "-" button and at the same time, put the battery in.
4. Wait a few second and release the button, then after a while, the device will be in bootloader mode. "
I have the same problem with 6815
Hello, I'm new to this forum I have problem with 6815, it's completly dead after trying to put wm 6.5 on it. I have tried to pull out battery, to put it back, to press "-" keys, to reset... but no succes. It's dead. Battery is fully charged. It's showing charging status when I conect it to the charger or USB PC port. Anyone, please help, doing it for a 2 days, my head and stomach are ruin...
Could anyone help me?
When I turn on the bootloader mode and connect it to pc,it won't make any connection and the red light won't turn on to..
Any suggestions?
I can't use my device because I can't flash new windows...
Could anyone help me?
First of all I’m running XP, and Active sync.
I used Soft SLP- VO.1 , I copied the NK.NBF
From a G4 safe rom into the soft slp folder.
While stuck in boot mode I did a hard reset,
Pluged in the usb and waited for power up.
Then I held the power button down and watched
Active sync try to connect at the same time started
Soft SLP . When active sync stopped I released the power button and then followed the instructions as normal. The phone went into white mode and copied all 100% but it still went into boot mode after it rebooted, but I was able to connect with the phone again. Now all we need is someone smarter then me that can figure out the rest of it. At least there is still hope for the dead ones.
Hi
there i purchase x10 mini pro and tried to update the firmware but my computer restarted and now my phone is showing a tringle and a exclamation mark as if its in a download mode how to rectify this
please help
tried everything i know but whenever it starts it goes in the usb download mode how get rid of this please help
have you tried this:
"Xperia X10 Mini Connect in Flash Mode
put SEUS ready to repair
connect the cable to phone and PC
press both middle and right button at the same time
press the power button
when phone goes down, keep pressing only the right button"
yes pc is recognising it but it gives
ok it is downloading the update lets c
i have repaired it and finished it it gave green colour light
it told me to remove the usb cable and restart the phone now
now when i start the phone it just blinks red light 3 times
aarif_ziaee said:
i have repaired it and finished it it gave green colour light
it told me to remove the usb cable and restart the phone now
now when i start the phone it just blinks red light 3 times
Click to expand...
Click to collapse
because you have to recharge the battery because its empty/exhausted... =)
Hi all
Today I received my freelander px2. I tried to follow the instructions posted here http://www.pandawillforum.com/showt...-PX2-MTK8389-Quad-Core-(update-Sep-6th-2013)/ to flash the device to the latest clean ROM. I got to the "Download" stage. I clicked the "Download" button and connected my Freelander PX2 with the USB cable.
I was having some issues making Windows 7 actually pick up the "MTK" device and load the correct driver. So I was playing around with the drivers and disconnecting and reconnecting the Freelander PX2 (Whilst leaving the Flash tool on DOWNLOAD mode, which was waiting for me to connect the Freelander PX2)
I must have reconnected it several times in the process of trying to make Windows 7 recognise the device. When I looked at the flash tool I noticed it had got to around 57% with the progress bar and stopped. I can only assume I managed to get the MTK drivers installed correctly at some point but tablet didn't really tell me new software was being uploaded to it. So basically I didn't know the flash tool was sending the new software to the tablet when I must have disconnected it during the process.
I can only assume I've interrupted the NAND flash process? When I try to reconnect the tablet now, it says "USB Device Not Recognized". There doesn't seem to be much support anywhere on the internet for this specific device or issue.
I've tried holding the power button for 30 seconds.. nothing happens
I've tried holding the power button plus volume up button for 30 seconds.. nothing happens
There's also no USB disconnect sound when I hold the power button down? Surely a hard reset should trigger a USB disconnect sound in Windows.
What are my options at this stage? Is it completely dead?
EDIT: Ok, this was a bit strange. I left it yesterday morning and declared it dead. Today I woke up, switched my computer on and plugged it in using a different USB cable and the driver was automatically installed as "MTK preloader". I didn't try to switch the device on yet though, as I wasn't sure if it being recognized was by chance. I didn't ask questions. I just immediately started up the flash tool, hit "download" and re-plugged the USB cable. This time the software finished upload with 100% and a green circle. Then it automatically disconnected from the computer. I hit the power button and it needed some time to charge again (maybe it drained itself last time). A few minutes later the OS booted completely fine. I don't know which one of those things made it worked, the new USB cable or leaving it to discharge for a day.. I just don't know. I'm not taking any chances though, the USB cable is being binned.
Have you flashed the CWM recovery for the px2 yet?
What do you think about the new firmware? I think its alot snappier than the old one. The CWM recovery works a treat (but you have no usb cable lol ) so you cant flash it. If you do want to put the recovery on it, let me know i can help. Cheers
PX2 Bricked
Hi,
Glad you got yours working :good:
I have exactly the same problem and now mine is not reconised :crying:
How long does the flashing actually take ?
When I connected it again this morning it it reconised it and the flash toll started to work.
The green bar and red bars both went to 100% then nothing after 5 mons so I unplugged it.
Now its bricked again :crying:
Any advice guys please ?
Reset
Hi mate sorry to here of your problems. Try pressing the little button between the sim slots, if that doesnt work, press volume + and then power button and keep pressed until it starts. When you flashed it did you get the green circle at the end?
If you get it recognized again do this: ENSURE YOU HAVE FULL BATTERY AND DO NOT INTERUPT THE FLASHING
1/ Start tablet and connect usb data cable, ensure it is connected as Media device (MTP).
2/ Unpack PX2_PC_24-10-13 update to a folder of your choice.
3/ Start Flash tool and click scatter loading on the right, and go to your unpacked folder you made earlier and select MT6589_Android_scatter_emmc check ALL boxes at the bottom are selected.
4/ Now click on downlod button, then switch off tablet. It will either ask to load drivers or start the flashing process.Wait until you see the green circle.
5/ Restart tablet. ENJOY
If you want to put clockwork recovery on it do the following:
1/ Download Freelander_PX2_130717_CWM_recovery.img in post #162 at pandawill put it in a folder and copy MT6589_Android_scatter_emmc from the folder above to the same folder.
2/ Start tablet and connect usb data cable, ensure it is connected as Media device (MTP).
3/ Start Flash tool and click scatter loading on the right, and go to your Freelander_PX2_130717_CWM_recovery.img folder you made earlier and select MT6589_Android_scatter_emmc only recovery option should be checked. Dont worry about the red writing.
4/ Click download and switch off tablet, dont worry about the warning just go ahead anyway, it will only take a couple of seconds and you should see the green circle again.
5/ To check it worked press vol+ and power button to get to recovery ( should be blue text ) if it is congrats you have clockwork recovery.
6/ Enjoy your tablet
Hi,
Thanks for your help but I fear it may be terminal,as when I plug the usb in now I get nothing.
gonna try on a different computor later.
If that fails I fear my PX2 will be leaving via the upstairs window
---------- Post added at 04:43 PM ---------- Previous post was at 03:57 PM ----------
Well it wont even charge now !
I wonder if this could mean a hardware problem or a software not sure ?
Any Ideas guys ?
:crying::crying::crying::crying::crying:
PX2 revival
Hi bazza500, try pressing the reset button between the sim slots it has saved me a couple of times when i thought i had bricked mine.
If you go to the pandawill forum under MTK tablets you will find a thread there dealing with an updated by users flashable firmware with cwm recovery.
Then later if you get it up and running there is a solution to extend the internal memory from 1Gb to 2Gb which reduces the storage by 1Gb. Hope you get it running buddy. Cheers
A few tips
Windows 7 has a glitch where by if the path has Chinese characters in it the flash tool with crash/error. Extract everything to your desktop and delete the chinese characters in the folder names.
Also there's a driver error in Windows 7. Make sure you use the driver install tool to install the MTK drivers. Also make sure the driver is installed and the tablet is recognised before you run the flash tool. That's the error I made, I tried to get the drivers installed whilst running the flash tool and the firmware started flashing when I hadn't realized.
Unlike Samsung and Apple, most Chinese devices don't give you a fancy progress bar on the device. There's almost no feedback the tablet or phone being flashed in most cases.
Thanks for the help guys................
Got my replacement today but have hooked it up to updrade and there was about 3 x colours went to 100% on progress bar now nothing for 15 mins !
Is this normal ?
Well a massive fail again.
Gonna send thos one back and get my money back.
Always a bad idea to by cheap o suppose u het what u pay for.
Sent from my GT-N7000 using xda app-developers app
Ok been awhile but I now have a new one and managed to upgrade the rom.
Only one problem I keep losing phone signal ?
Any ideas?