help brick atrix on 2.3.6 - Atrix 4G Q&A, Help & Troubleshooting

i try to unlock my bootloader with this Automatic bootloader UNLOCK/ROOT for AT&T 1.26/1.57/1.83/4.5.91 [UPDATE 07/31/11] i found in the tread now i get fail to boot 0x1000 SVF 105:1:2 how can i go back to stock 2.3.6 help me please .i can still get into fast boot. my phone was on 2.3.6/ 4.5.141 when i try to unlock the bootloader with this method

It sounds like Nottach ran into a similar problem when unlocking his:
He tried holding the power + volume up buttons WHILE inserting the battery, and the hardware gods smiled & the phone booted into fastboot to finish the unlock procedure.
On edit: You say you now have fastboot access? So long as that's true, it's not a "hard brick" yet. If you haven't finished unlocking the bootloader, the next step is to issue the "fastboot oem unlock" command & finish it out. I do believe you'll have to flash a fruitcake or another rom to get your phone back and functional.

Related

FAILED TO BOOT 0x1000 Help me please!!!

I bricked my phone by Flashing pudding with RSD LITE before I unlock my bootloader. Someone told me I should flash pudding to unlock bootloader. Flashing procedure has failed and I got this at the end : http://tinypic.com/r/2lfk1/6
I was on gingerbread 4.5.91, rooted ATT device. I bought it from USA and I'm in Turkey now. I cant send it to warranty.
Is that a soft or hard brick? Can I fix it?! Please say yes.
Please, Help me! I am waiting your answers.
(I'm so noob about the phone, please tell me with more informations)
Does this look like a hard brick to you?
(If you can't tell, the answer is no.)
---------- Post added at 09:07 PM ---------- Previous post was at 09:06 PM ----------
Wait, what SBF did you use? This **** is important.
i think you can still unlock your bootloader through fastboot,
and then flash system image..
Boot into fastboot mode and use the fastboot OEM unlock code from your computer, please read all the instructions in the pudding thread before panicking
Sent from my MB860 using xda premium
Lol! Don't panic, I just got out of the same situation a few hours earlier. Get your atrix into fast boot mode by pressing power and vol up buttons while placing the battery. Then proceed to unlocking your bootloader. Flash a boot image to get your atrix to boot into OS again, follow this http://www.android-advice.com/2012/flash-the-motorola-atrix-4g-back-to-stock-4-5-91-rom/ if you break your wifi like I did, just follow "Alaq's" Moto-Fastboot: Stock Restore. http://forum.xda-developers.com/showthread.php?t=1421522 or you can just flash the 2.3.6 from this https://sites.google.com/site/motosbf/atrix-sbf-files using rsd lite, open rsd lite, turn on your atrix and connect to your computer, you'll see rsd will still recognize your atrix, then flash the sbf file.
Sent from my Atrix 4G
Too many problems on here result from the people that don't read. You have eyes for a reason!
I'm in Thailand. My phone is show FAILED TO BOOT 0x1000 for 3 second then black screen. Is my phone paper weight or not?
term4802 said:
I'm in Thailand. My phone is show FAILED TO BOOT 0x1000 for 3 second then black screen. Is my phone paper weight or not?
Click to expand...
Click to collapse
This isn't very specific. Can you get a picture?
seem that u have bricked your [email protected]@
Sent from my MB860 using Tapatalk 2
nerfman100 said:
This isn't very specific. Can you get a picture?
Click to expand...
Click to collapse
Thank you for your kind. sorry I am new XDA's user . my clip in youtube
/watch?v=muujX75TVm0
Eek. I'm not sure if you can solve this. If holding Power+Volume Down after the green light shines displays the word Fastboot, there might be hope.
Thanks
eowyn said:
Lol! Don't panic, I just got out of the same situation a few hours earlier. Get your atrix into fast boot mode by pressing power and vol up buttons while placing the battery. Then proceed to unlocking your bootloader. Flash a boot image to get your atrix to boot into OS again, follow this http://www.android-advice.com/2012/flash-the-motorola-atrix-4g-back-to-stock-4-5-91-rom/ if you break your wifi like I did, just follow "Alaq's" Moto-Fastboot: Stock Restore. http://forum.xda-developers.com/showthread.php?t=1421522 or you can just flash the 2.3.6 from this https://sites.google.com/site/motosbf/atrix-sbf-files using rsd lite, open rsd lite, turn on your atrix and connect to your computer, you'll see rsd will still recognize your atrix, then flash the sbf file.
Sent from my Atrix 4G
Click to expand...
Click to collapse
Exactly...I too tried to flash my phone, OS got corrupted and followed the same procedure to recover my phone, without any single data loss I got back my phone.
Main thing that we want to note while flashing the phone is Version of the flash file which we are trying to flash, if it is downgraded version then there is 80% of chance for OS corruption. so before flashing check the version.
It's a softbrick
get into fastboot using volume rocker keys.
use command line on windows
fastboot oem unlock
fastboot oem unlock ################
done.
Thanks,
Jinesh

[Q] I am stuck on unlocking 4.5.91

Hello everyone.
I own Motorola Atrix 4g AT&T with 2.3.4 / 4.5.91 Build.
I have read every single thread about Unlocking the bootloader yet I still cannot do it.
First I tried directly the fastboot unlock command for unlocking it but I had an error saying that OEM Unlock is not implemented. Thats OK since the stock bootloader isnt unlockable. So I downloaded RSD Lite as well as the two SBF files (the small pudding and the huge pudding (full version) of AT&T unlockable/pre root) Here is where I got stuck! I have the drivers properly installed and I tried both Windows7 and WindowsXP still i cant get past the boot logo. Here is the situation.
I connect the Phone in RSD Mode. In RSD Lite it shows as NS Flash Olympus and stays connected. When I load the SBF file and press start it gets to 100%. Then phone reboots and RSD Lites says that its waiting for phone to re-enumeration and after a while it gets the error message: Phone[0000]: Phone did not re-enumerate after RAM-downloader was sent.. Phone is still stuck on the Moto Logo untill I remove the battery. If I remove the battery Phone starts.
Am I missing something?
As far as I remember, once you flash pudding the phone will indeed seem unusable. Immediately after flashing pudding you need to go into fastboot and run the oem unlock commands, then you need to flash a custom recovery, then boot into recovery and flash a custom ROM. You miss any of these steps and the phone will very likely not boot.
ravilov said:
As far as I remember, once you flash pudding the phone will indeed seem unusable. Immediately after flashing pudding you need to go into fastboot and run the oem unlock commands, then you need to flash a custom recovery, then boot into recovery and flash a custom ROM. You miss any of these steps and the phone will very likely not boot.
Click to expand...
Click to collapse
The problem is that i cannot flash pudding since I get an error message after the extracting process when the phone is suppose to reboot and flash itself. It just reboots and stays with Motorola logo (RSD Lites gives me the error) and phone freezes untill I remove battery. After that when I power on the phone it just loads normally.
So the problem is that I cannot flash pudding.... simply because phone dosnt reenumerate after reboot....
Bump ...
I want to add that the phone dosnt have backlight in boot menus (ak. background light is turned off but i can still see the options in boot menus)
Also I am not able to install OTA Updates I get a triangle on the screen and phone boots into os with failed to update message.
Else phone is fully functional. I havnet done anything except rooting the phone and doing the tethering and webtop over hdmi hack.
m140n1 said:
Bump ...
I want to add that the phone dosnt have backlight in boot menus (ak. background light is turned off but i can still see the options in boot menus)
Also I am not able to install OTA Updates I get a triangle on the screen and phone boots into os with failed to update message.
Else phone is fully functional. I havnet done anything except rooting the phone and doing the tethering and webtop over hdmi hack.
Click to expand...
Click to collapse
Try this automated tool. There are several options to choose from.
Download tool here.

[Q] Need help simi/bricked motorola electrify

Sorry i did not have the kernel or most information about the phone but ill explain the problem if anyone can help out it'd be a blessing
i have a U.S cellular Motorola electrify running 2.3.5 ( which recently found out was unrom-able)
i got it rooted using one touch method--
Then not thinking -- ( ive rooted and installed roms on other phones never a Motorola) didn't know it needed a unlocked bootloader to function and get roms installed.
i knew i needed a clockworkmod on the phone and i read about the app that boots into clockworkmod bootstrap--apk
did that and it worked--
here is the problem..
didn't install the bootloader.. and tried installing Cyanogenmod10 unofficial rom from photon development forum
rebooted-- got Failed to Start2- starting rsd mode -- if i dont press anything
if i press down it says NV recovery but does nothing
if i press UP it goes into Starting usd recovery ( sorry not exact words not with my phone at the moment)
ive been reading guides.. downing the lock unlock from the bricked guide.. RSD lite would read the phone in the usd recovery
try flashing the offical us cellular back but get an error
wont show up in command prompt
not sure what to do.. please help its hard to function without a phone i hope its not fully bricked
Can you get into fast boot by pressing power and volume-down? If so, you just need to wipe everything using "fastboot -w" and rebooting into RSD mode to flash the uscc sbf.
When you flashed cm10, the kernel is not compatible with the bootloader you're on.
If anyone has the 2.3.5 electrify boot.img, you could probably flash it through fastboot if it'll let you
Sent from my sunfire using xda premium
hoslayer13 said:
Can you get into fast boot by pressing power and volume-down? If so, you just need to wipe everything using "fastboot -w" and rebooting into RSD mode to flash the uscc sbf.
When you flashed cm10, the kernel is not compatible with the bootloader you're on.
If anyone has the 2.3.5 electrify boot.img, you could probably flash it through fastboot if it'll let you
Sent from my sunfire using xda premium
Click to expand...
Click to collapse
Thank you for the reply.. when I press volume down and boot on it says " nv flash mode" then turns off unless hooked in a computer then just stays on that screen
If I press volume up and turn on it says fast boot protocol support and Is half recognized in rsd ITE
If I just power no volume press on it says failed to boot 2 starting RSS mode..
I'm sort of new to everything and need more details.. tryed wiping using fast boot u downloaded but gives error.. same with flashing yes cellular sbf in RSd lite trying all 3 button combos that work
Please I need this phone working.. I messed up someone's phone saying I could put cm10 it for Christmas! Any help would be awesome

Moto E Soft Bricked

So I had a moto e with it's bootloader unlocked, and had a custom ROM running on it; however without my knowledge, someone gave the phone to a local (unauthorized )service center. I am not sure about what they did but after this incident, I get the Bootloader unlocked warning when it powers on, but then it directly goes to the fastboot menu saying that there was a fall through in the normal boot-up procedure, and 'system image validation failed'. However I was able to boot into android by rebooting a number of times. But recently, when it did boot up after several attempts the IMEI numbers were gone, so it wouldn't recognize my SIM cards.
I should also mention that the fastboot menu says that the phone is LOCKED. I tried using fastboot, but i cannot even get the unlock code info, or unlock the bootloader itself.
At this point, what do I do? Do I try flashing the same firmware again?
Thank You.
Try flashing the stock firmware :fingers-crossed: Best of Luck!
Hit Thanks if I Helped!!!!!!!!!!!

My phone is not booting

I don’t know what happened to my phone, but I booted up the phone and I get the error in the picture below. The boot loader is locked and I can’t unlock it, it says “flashing unlock is not allowed “ and I can’t access download mode or any mode except boot loader.
So is there anyway to revive my phone again? Maybe force unlock boot loader or flashing stock bios using fastboot?
Thank you for your time.
moomlufi said:
I don’t know what happened to my phone, but I booted up the phone and I get the error in the picture below. The boot loader is locked and I can’t unlock it, it says “flashing unlock is not allowed “ and I can’t access download mode or any mode except boot loader.
So is there anyway to revive my phone again? Maybe force unlock boot loader or flashing stock bios using fastboot?
Thank you for your time.
Click to expand...
Click to collapse
Press and hold power key to continue
You probably pressed power button which paused it from going further
That's the ugly Red safety warning, not the benign yellow one. As I understand, this is what happens if the bootloader is locked and one of the partitions fails its security check. All partitions must be completely stock when the bootloader is locked.
@runningnak3d described this somewhere, and I seem to recall it's a hard brick, or at least pretty hard. But I hope I'm wrong

Categories

Resources