Related
Does it really help to have a screen protector on STR? My nook is always inside a case, and always have some finger smudges on the screen, which does not interfere with reading the screen content.
Would it make the screen harder to use, such as in a resistive screen? I know it has IR technology, not resistive lcd, but it is good to know...
I have a screen protector, because I have cats and dogs who're lurking around my nook, and I'd hate to see them scratch the screen. I'm not using any case for it. The film does not affect the touch sensitivity in any way...
thanks for the info, emarusceac.
I can see dogs and cats and stuff being a problem. I just have an old NC sleeve laying around that works. If you can stand the wait, ebay is cheap Turns out the NC and NST width is the same...
emarusceac,
what sort of screen protector are you using?
Hi mh127,
I'm using a basic anti-glare screen film from ebay.
The nst is the first touch screen I have not used one on.
It is perfect now, the matte should hide small scratches, it gets used more lightly than phones/tablets, it is light (less damage if dropped), and it is cheap!
I am going to buy one.
I must warn you that it's VERY hard to apply it smoothly. I mean you'll get some air pouches caused by small particles, those bubbles won't go away no matter what you do. I prefer bubbles to permanent scratches though....
emarusceac said:
I must warn you that it's VERY hard to apply it smoothly. I mean you'll get some air pouches caused by small particles, those bubbles won't go away no matter what you do. I prefer bubbles to permanent scratches though....
Click to expand...
Click to collapse
I ordered one. Was concerned that it would be tough to apply because of the high frame around the screen. Any tips how to apply well? You use a credit card to smooth the film down over the screen?
Oh one more thing. Has anyone tried removing one? Does it change or damage the screen in any way?
I have had several different screen protectors on my NST and none of them caused any damage when I removed them. I would note though that I have read that you must not apply a screen protector to the Glowlight, something about the built in screen protector and its light guide properties. I would also point out the one reason my NST has had multiple screen protectors is because they are so hard to apply without getting bubbles/lint between the screen and the film. The film I have on now I finally got applied without any bubbles/lint in the reading area, so it will hopefully be on there for a while. Make sure you are working in a CLEAN area and take great pains to get it lined up straight before actually applying it to the screen.
The NST doesn't need a screen protector, it really wont do much for the device, but if you really feel like spending the money for it go ahead.
The NSTG already has a protector built in, putting an extra one on would be like putting on an extra pair of latex gloves. It'll offer a little more protection, but it can get to be quite frustrating in terms of lost control. It's advised not to bother with a protector for the NSTG.
Personally unless you know you're going to have your NST in reach of creatures with claws, or lose objects with sharp edges the protective screen will do little for you. Even in those cases it's possible the screen would merely lessen the damage done rather than prevent it out right.
In regards to the NSTG and it's pre-installed screen protector, has anyone actually removed it? I've read lots of reports of people complaining about minor scratches and finger pressure marks causing the light to become very strong on those parts, wondering if removing the screen protector would fix that or whether it's instead a problem with the screen.
Xadious said:
In regards to the NSTG and it's pre-installed screen protector, has anyone actually removed it? I've read lots of reports of people complaining about minor scratches and finger pressure marks causing the light to become very strong on those parts, wondering if removing the screen protector would fix that or whether it's instead a problem with the screen.
Click to expand...
Click to collapse
They claim there is one, I claim they lie as there is no visible edge of one. If there was you wouldn't get the light flares from minor scratches. Adding one may protect the screen but no idea what it would do to the light guide properties of the screen. If you ever have to remove it I'd worry what would happen to the light guide layer.
Because gadgets capabilities/sppecs increase rapidly & prices drop fast too, unless it's expensive I forget about screen protectors if the device is cheapish (got mine cheap) & if it will be outdated in a couple of years. Specially if it's not an outdoor device like my phone. Or if the protector hampers speed / functionality to some degree. Also personally I rarely scratch tab screens unless it's a phone, my phones/tabs all have protectors put on from day one, but not doing my NTSG. YMMV.
Guys I noticed that after 3 weeks of use the pre applied screen protector has a lot of small tiny scratches.
I'm normally very cautious with the screen no scratches on my previous phones (one gorilla glass and two with screen protectors (those had the same only after a lot of months of use and replaced by a new one)
Is the purpose of the pre applied sheet only to keep the screen in one piece in case of the worst case and the phone drops?
Or is it a screen protector which can be replaced?
What is your experience here
O and for the guys which using the phone without the protector how turns that out in daily use?
awf said:
Guys I noticed that after 3 weeks of use the pre applied screen protector has a lot of small tiny scratches.
I'm normally very cautious with the screen no scratches on my previous phones (one gorilla glass and two with screen protectors (those had the same only after a lot of months of use and replaced by a new one)
Is the purpose of the pre applied sheet only to keep the screen in one piece in case of the worst case and the phone drops?
Or is it a screen protector which can be replaced?
What is your experience here
O and for the guys which using the phone without the protector how turns that out in daily use?
Click to expand...
Click to collapse
I've removed the pre-applied screen protector since day 1. It's actually making my screen's sensitivity very low. I'm using only one sheet of anti-glare screen protector on it, and it had been working well for me.
Just pulled my preinstalled protector off as it was bugging me. Not sure I have done the right thing! The screen now feels a bit sticky even after a good clean. However the capacitive buttons do feel a bit more responsive.
Will report back after a couple of days without it.
Leave it there...
The company decided to place a screen protector (placed it perfectly) coz a lot of people like it's presence for more protection for their devices.
You have the choice to keep it or peel it off as u wish.
IMO; leave it there until it's unbearable for u, then u can remove it and replace it with another high quality one!
And for the responsiveness issue, in my experience with my other devices i've never felt any difference between having it on or not!!!!
I'm not remove the preinstalled screen protector but add in 1 more layer screen protector which is coming out of the box.
After a day without my screen protector, I am pleased I went ahead and removed it. I have now cleaned the screen with glass cleaner and the stickiness has gone. Colours are slightly improved and there is an extra, if subtle, sharpness to the screen.
The main improvement is that the capacitive buttons are much more sensitive than before.
I've just removed mine, the difference to touch response is great
Sorry but for me, I HAVE to wear the preinstalled or any other screen protections. I can NOT go with my phone and when I see a scratch in my screen I know it will be there for ever! With screen protection I always know when I see scratches in my screen(protection) I know its only the protection that got scratched.
So but that's me. Don't care if the screen gets a little bit more responsive, protection is important!
Sikiduck said:
Sorry but for me, I HAVE to wear the preinstalled or any other screen protections. I can NOT go with my phone and when I see a scratch in my screen I know it will be there for ever! With screen protection I always know when I see scratches in my screen(protection) I know its only the protection that got scratched.
So but that's me. Don't care if the screen gets a little bit more responsive, protection is important!
Click to expand...
Click to collapse
First really appreciated everybody's input/view
Was just wondering in daily use you don't notice it with screen on, but with screen off you see it under light so wondering see reply from Sony
http://talk.sonymobile.com/message/174865#174865
So maybe useful for fellow users which wondering the same thing
awf said:
First really appreciated everybody's input/view
Was just wondering in daily use you don't notice it with screen on, but with screen off you see it under light so wondering see reply from Sony
http://talk.sonymobile.com/message/174865#174865
So maybe useful for fellow users which wondering the same thing
Click to expand...
Click to collapse
You are asking the right questions! I look forward to the next response from Sony on part number vs your querying about a protector on-top of a protector.
If people are finding touch sensitivity affected with one layer, two layers must be even worse!!
how the heck do you even remove this??!
I've got two on, and pre applied and one that was in the box (put that on before I knew about the pre applied one) touch realy isn't bad, but i swipe the 3 menu buttons as habit now, and works pretty good. I have a year on contract left, and i hate scratches so I'm happy XD
Sent from my ASUS Transformer Pad TF700T using XDA Premium HD app
I use two layers as well. Generally Swype up for the buttons. And am perfectly happy with the responsiveness of the screen and buttons
Sent from my LT26i using xda app-developers app
Thinking Gorilla Glass was scratch resistant as I have seen on YouTube, I showed my friend that it doesn't scratch. I took a coin and rubbed it on the screen. I wasn't even pushing that hard. When I look, there are thin scratches from the coin! They are only noticeable when the screen is off. Except for two small ones. They are about 5 mm long and pretty thin. They are visible all the time especially when there is a white background. They distort the colour and now I'm obsessed knowing they are there. Is there any way to remove them? Such as tooth paste or some other material? I don't want anything that will remove the oleophobic coating on the screen. Just something to fill in the scratches. Thanks!
Im sure there is a polish for delicate glass. GOOGLE is your friend.
http://forum.ppcgeeks.com/moto-droid/114659-gorilla-glass-does-scratch-but-i-know-how-repair.html
So did your mate laugh and take the pi$$ for being a smart a$$?
My name is Optimus Prime and I send this message..
Gabewalters said:
I took a coin and rubbed it on the screen.
Click to expand...
Click to collapse
Don't be surprised when Asus reject your RMA request?
Sure it's scratch resistant, but it does not mean you should go out and rub a coin into it.
Sorta like trying out a bulletproof vest by shooting yourself...
I also have a tiny scratch right where the bezel meets the display because i droped a lighter on my prime once.
Glass will always be susceptible to scratches no matter what brand, its physics! Would be cool to have a tablet with a diamond touchscreen though. Now that would be scratch proof
I once dropped my Evo 3d with an extended battery on my prime. No scratches and that thing was heavy and it was from 4-5 feet as well. Landed screen first.
Sent from my tf9001 with XDA XD.
Gabe
I feel your pain!
Why don't you put a screen protector on your device? First, if nothing else, you'll be sure not to add any additional scratches to your screen.
2nd, other people have posted that scratches were not visible once they put a screen protector on their screen.
I have tried three different ones, ArmorShield, Skinomi and ACase.
Really like the A Case screen protector, and it comes three to a pack, so if you mess up the first one, you still have two more (it's a dry apply screen shield)
Good luck!
Wow people really do confuse the difference between "-proof" and "-resistant". Have you ever tried submerging a water-resistant watch in water?
In any case, most touch screen devices these days are coated with oleophobic coatings which scratch much more easily than glass.
Sent from my Galaxy Nexus using Tapatalk 2
You almost certainly scratched the oleophobic coating, not the screen itself. Not that it matters really, the screen still looks scratched. Those coatings are not nearly as tough as the underlying glass. I have noticed similar little scratches on my Galaxy Nexus screen. All in all, I still think the coating is great though.
http://forum.ppcgeeks.com/moto-droid/114659-gorilla-glass-does-scratch-but-i-know-how-repair.html
Your welcome.
pileot said:
http://forum.ppcgeeks.com/moto-droid/114659-gorilla-glass-does-scratch-but-i-know-how-repair.html
Your welcome.
Click to expand...
Click to collapse
You're welcome.*
Sent from my Transformer Prime TF201 using Tapatalk 2
bedoig said:
You almost certainly scratched the oleophobic coating, not the screen itself. Not that it matters really, the screen still looks scratched. Those coatings are not nearly as tough as the underlying glass. I have noticed similar little scratches on my Galaxy Nexus screen. All in all, I still think the coating is great though.
Click to expand...
Click to collapse
That makes plenty of sense as im pretty sure glass wont scratch from the little amount of pressure i was applying. The thing is, there are two small spots, one being around 5-7 mm long and the other being only around 2 mm long. They are mostly only noticed when a light coloured backround is on, such as the white backround in the browser. They seem to show up sort of ''Rainbowish' these ones must be the actual glass that is scratched because otherwise i doubt they would show up like that. Anyways, thanks for the kind reply!
ShelW said:
Gabe
I feel your pain!
Why don't you put a screen protector on your device? First, if nothing else, you'll be sure not to add any additional scratches to your screen.
2nd, other people have posted that scratches were not visible once they put a screen protector on their screen.
I have tried three different ones, ArmorShield, Skinomi and ACase.
Really like the A Case screen protector, and it comes three to a pack, so if you mess up the first one, you still have two more (it's a dry apply screen shield)
Good luck!
Click to expand...
Click to collapse
I am considering purchasing a screen protector ASAP. Does the Acase screen protector show up in anyway? What i mean is, will the screen look any different? An example would be an anti-glare screen protector makes the screen more matte and i dont think the colours show as nicely. Thanks for the recommendations!
Namidairo said:
Don't be surprised when Asus reject your RMA request?
Sure it's scratch resistant, but it does not mean you should go out and rub a coin into it.
Sorta like trying out a bulletproof vest by shooting yourself...
Click to expand...
Click to collapse
Gorilla Glass (even second version) is a piece of sh#it and was always it. I'd like to have the DragonTrail Glass in my gadgets :
http://www.youtube.com/watch?v=WpbOoQpwAFs
Gabewalters said:
That makes plenty of sense as im pretty sure glass wont scratch from the little amount of pressure i was applying. The thing is, there are two small spots, one being around 5-7 mm long and the other being only around 2 mm long. They are mostly only noticed when a light coloured backround is on, such as the white backround in the browser. They seem to show up sort of ''Rainbowish' these ones must be the actual glass that is scratched because otherwise i doubt they would show up like that. Anyways, thanks for the kind reply!
Click to expand...
Click to collapse
Those might actually be small fractures in the glass. Similar occurrences have been discussed in the My Screen Cracked (or something like that) thread. It seems like Asus may have a glass quality issue with some of their units.
bedoig said:
Those might actually be small fractures in the glass. Similar occurrences have been discussed in the My Screen Cracked (or something like that) thread. It seems like Asus may have a glass quality issue with some of their units.
Click to expand...
Click to collapse
How would the screen have fractured from a quarter that rubbed on the screen? That makes sense of why the scratches are deeper than the others but I don't know how the screen would fracture. Is there anyway I can try to ride these fractures/scratches? I have been searching for weeks now and the best product I could find would be "iDrops" they polish out scratches but people say it's removed the oleophobic coating. Will some sort of toothpaste rubbed into the scratch work?
Sent from my Transformer Prime TF201 using XDA
Gabewalters said:
How would the screen have fractured from a quarter that rubbed on the screen? That makes sense of why the scratches are deeper than the others but I don't know how the screen would fracture. Is there anyway I can try to ride these fractures/scratches? I have been searching for weeks now and the best product I could find would be "iDrops" they polish out scratches but people say it's removed the oleophobic coating. Will some sort of toothpaste rubbed into the scratch work?
Sent from my Transformer Prime TF201 using XDA
Click to expand...
Click to collapse
No that will only make it worse (toothpaste at least). I think you have to accept it can't be 100% fixed with some paste/polish. You could contact Asus for a new touchscreen.
I've had my prime since December with no screen protector or case. i use it extensively everyday. no scratches at all on my display or back cover.
I really don't care if the scratches can be seen when the screen is off I just don't want them to be visible when the screen is on (rainbow like). As long as they aren't visible when the screen is on is fine with me. Do you know of any fine polishes that might do this that won't harm the glass or the screen?
Sent from my Transformer Prime TF201 using XDA
My Prime once fell of from a bed on the floor, around 40-50cm, it didn't got any scrathes as it was attached to the dock, and was half open, though now I have a feeling the dock does not hold the tablet so tightly as before.
But what I don't like about the Gorrilla Glass (or either it's not calibrated touch detection in the software side) is that the Tablet does not detect my touches when I use the back side of my finger (finger nail), does anyone else have the same issue? Other touch devices I have (iPad and EVO 3D) detect my touches from front and back of the finger the same without issues.
I actually have a HOX with Gorilla Glass 2, but this seems to be the most active and recent thread regarding removal of scratches from GG, so I suppose it'd still be rather relevant. No point starting a new thread just for GG on a different device, right?
Yes, I babied this phone like... a baby since i got it on the first day and no screen protectors were out yet, but somehow it still got a nick(rather visible) in the upper left corner and some light scratches around the middle of the phone.
Then I found some manufacturing defects but I'm afraid they'll refuse to repair/replace my phone under warranty if they see the nick.
So has anyone found any way to cover up the scratches? Even temporarily, just to get through the chat with the assistance team? (No I can't get 3M's 06070, lowest quantity sold here is 6 quarts for ~$400. Way too expensive.)
Ok I have removed my screen protector that was pre-installed on the Xperia S and it has seemed to go okay for me. I wanted to write a little guide to inform others incase they have been thinking of doing it.
Pros:
Capacitive buttons are much more responsive. I usually get them every time now.
No more little edge at the top of the clear section. I hated how there was a sharp edge caused by the screen protector when I went to swipe the buttons. No problem with it now.
Screen is more responsive to touch.
The phone looks better. No dust gets in the screen protector edges and the screen looks a little clearer.
Cons:
The screen is not as protected against scratches or falls.
The screen gets VERY dirty quickly. Be prepared to rub it off all the time as fingerprints seem to slime up the screen quickly. I guess they didn't use an oleophobic coating to reduce the dirt and grime. It's not a deal breaker, but it sure as hell is annoying.
The proximity sensor is much easier to trigger, so when you are using it and it goes over the sensor it will quickly turn off the screen.
There is a slight gummy sensation left over by the screen protector residue. It will dissipate after some time but it can be really annoying. Use some alcohol and a coarse rag to get it off sooner.
I prefer the feel of the screen protector to the screen itself. The screen seems to not be as smooth but maybe there is still some residue left over.
Sidenote:
I have dropped the phone from 3 feet onto industrial thin carpet and it is still okay even without the shatter proof sheet. Remember that almost every phone will have problems if you drop it onto a hard surface and it lands on the edges.
The screen material seems to be very resistant to scratches. I have a defective unit that is being returned so I decided to do a couple tests on it before sending it back in. I used a key to scratch the screen in the corner. First I tried a light scratch and then I tried a medium pressure scratch. Neither of these showed a mark. Even a pretty heavy pressure did not leave a mark. I am pretty satisfied with the results though I imagine if you used a sharp edge and a lot of pressure it would scratch it. Better than I had thought though, Gorilla glass is overrated anyways.
Let me know if you have more questions.
EDIT:
To remove the screen protector, just use fingernails and pry it up near the bottom, top of the clear bar. Once you get a piece peeled up, grab it firmly and pull the rest off. If it is still really hard heat the screen with a hairdryer for a second or two and it will loosen the glue.
http://forum.xda-developers.com/showpost.php?p=26467442&postcount=64
Sent from my LT26i using Tapatalk 2
I took mine off with no regrets, the sticky does wear off.
gm007 said:
http://forum.xda-developers.com/showpost.php?p=26467442&postcount=64
Sent from my LT26i using Tapatalk 2
Click to expand...
Click to collapse
I don't believe that post to be correct, Sony support site has stated you can remove it and be just fine. You just won't have that extra layer of protection. I have dropped mine without the shatter proof sheet and it is fine. I'd like to see some proof about how much security the "shatter proof" sheet will add. Even after reading that post, I feel that the shatter proof sheet is just an added piece of marketing so that people will not complain as much by the lack of gorilla glass. Sony would have put Gorilla Glass in the phone if they thought it was necessary and made the warranty void if you removed the sheet, but they did neither.
The shatter proof sheet makes the screen feel terrible. I will never use mine. I never had a screen protector on my HTC Hero and I never had a problem.
The most optimal thing to do is remove the shatter proof sheet and add a screen protector to help deal with the oils and dirt from your hands.
If you worry that much about shattering your screen then get a SquareTrade warranty.
Maybe you are right but I don't think they put this sheet just for decoration,i remember they did also for the X10 and I remove it in this time but the screen get less responsive.It's some kind of protection against scratching.
I will never remove it,that's only my opinion.
Sent from my LT26i using Tapatalk 2
gm007 said:
Maybe you are right but I don't think they put this sheet just for decoration,i remember they did also for the X10 and I remove it in this time but the screen get less responsive.It's some kind of protection against scratching.
I will never remove it,that's only my opinion.
Sent from my LT26i using Tapatalk 2
Click to expand...
Click to collapse
The shatter proof sheet scratches easier than the mineral glass. Like I listed above, I tested scratches the raw screen with keys at different pressures and I got nothing. Mineral glass is damn hard and Sony is supposed to use a special type.
It's your call though, I am just trying to add some info for others.
Also there is no reason for removing the sheet to make it less responsive since you are actually removing another layer which is getting between your actions and the digitizer, it doesn't work that way.
I don't know why the screen get less responsive,maybe the glue can't be removed easily.
Sent from my LT26i using Tapatalk 2
gm007 said:
I don't know why the screen get less responsive,maybe the glue can't be removed easily.
Sent from my LT26i using Tapatalk 2
Click to expand...
Click to collapse
That could be it, I hated the feel first off. Used some goo gone and alcohol and it cleaned it right up. The thing that makes mine feel worse after removing it is the oils and dirt stick like mad to the raw screen. Im gonna put a really thin one on just to protect from that, but I am glad I removed that terribly think one.
I agree that the most annoying thing if you dont use screen protector is fingerprint/oil smudge
I took it off aswell and hated the feel of the pure glass... Just too sticky and the fingerprints nearly made me crazy so i put on a normal 1
Sent from my LT26i
i notice that without that screen protector you will have unresponsive touch when charging from usb or wall or even with headphone plugged in.... i just ordered a zagg invisible ^_^
mrsatan said:
I guess they didn't use an oleophobic coating to reduce the dirt and grime. It's not a deal breaker, but it sure as hell is annoying.
Click to expand...
Click to collapse
Cant be used with a screen protector. On phones that do have the oleophobic coating, putting on a screen protector makes it useless because as soon as you remove the protector the coating would also be removed with it.
It's just that a phone shouldnt have a factory applied protector it's ridiculous. I myself never use a screen protector and probably will never.
This post might sound funny but for quite a few days, I actually had a Matte screen protector over the screen protector preinstalled by Sony. I actually had no idea it was even there until I found a post on XDA about the same and then checked the earpiece region and then, *facepalm*
A few notes from that, the screen was still responsive and I actually liked it better than the Arc S one. The capacitive buttons weren't responding as well and I didn't like it initially but once the useless matte protector was off, everything was as smooth as butter. I personally like to have an additional layer of protection just as a safeguard. Gives me more sense of security (even though there isn't much).
drigerott said:
i notice that without that screen protector you will have unresponsive touch when charging from usb or wall or even with headphone plugged in.... i just ordered a zagg invisible ^_^
Click to expand...
Click to collapse
I have never had that problem with mine removed. Why that would happen does not make any sense anyways.
mrsatan said:
I have never had that problem with mine removed. Why that would happen does not make any sense anyways.
Click to expand...
Click to collapse
just search unresponsive screen on xda you will find hundred treadh about this problem
drigerott said:
just search unresponsive screen on xda you will find hundred treadh about this problem
Click to expand...
Click to collapse
What I meant was why would removing the laminate sheet make the buttons less responsive. Mine are MUCH more responsive without it and I have forgotten about the complaints leveled against the capacitive buttons because of it.
mrsatan said:
What I meant was why would removing the laminate sheet make the buttons less responsive. Mine are MUCH more responsive without it and I have forgotten about the complaints leveled against the capacitive buttons because of it.
Click to expand...
Click to collapse
He is speaking about the screen not the buttons
Sent from my LT26i using Tapatalk 2
mrsatan said:
The shatter proof sheet scratches easier than the mineral glass
Click to expand...
Click to collapse
Lol that's why Sony bundles a screen protector, to protect the shatter proof sheet from scratching.
Your SUPPOSED to have two layers, the lower layer protects from shattering and the upper layer with the screen protector of your choice protects from scratching.
All this talk of you telling people to take off something using goo gone on a brand new phone is ludicrous. Just install the screen protector provided over the laminate sheet as soon as you take it out of the box as Sony designed it and be done with it.
I'm reading all this and was kinda kept by surprise for hearing for the first time about this sheet, since I can't find it on my XS. Is it possible that my unit came without this shatter-protection-layer-sheet-thingy?
Look closer to the edges
Sent from my LT26i using XDA
Ultimate Shield Tempered 9H Glass screen protector
Hey guys, here is my review of the Ultimate Shield Tempered 9H Glass screen protector and I must say - I'm converted!!
Read on....(also see the attached pictures)
Contents:
- The tempered glass screen protector
- Screen cleaning cloth (wet)
- Dust stickers
- Microfiber cloth
Installation:
Be sure to do this in as dust-free environment as possible. I like the kitchen for this reason (no carpets for me there), or the bathroom works great too as you can use the steam from the shower to help any dust settle whilst you complete the install!
1. Using the wet cloth helps to give the screen a good clean removing any oily fingerprints and/or dirt.
2. The dry cloth dries the screen (don't worry, the wet cloth doesn't 'wet' it that much!) and the dust stickers are there to ensure any last little bits of dust aren't present.
You'll want to spend time on ensuring there are no little bits on your screen as this can spoil the look, at least to those who won't be able to stop noticing that little eyelash hair in the middle of the screen!
3. Carefully remove the protective layer of the screen protector, keeping the exposed glass side facing down. There is a slight adhesive, of some form, which any bit of dust/hair ending up there may be tricky to remove so make this step as swift as possible, taking extra care. Keep your thumbs/fingers away from that side of the glass to avoid any fingerprints getting stuck there, holding the protector by the side only.
4. Lower the screen protector towards your phone, but don't place it on quite yet. Really line up the protector, looking at it from directly above and I'd recommend using the camera cut out as the guide. Ensure the selfie-camera lines up nicely in the hole but also that the full length of the protector runs parallel to the phone.
5. Once you're happy with the alignment, place the protector on the screen, with the selfie-cam side down first, then slowly but firmly lowering the rest of the screen protector down. Or to say another way, press the top of the screen protector down and then press towards the lower end of the protector, until you reach the bottom speaker end.
6. Some bubbles may be trapped underneath the screen. Don't worry! Use your finger/thumbs to firmly yet carefully press out the bubbles, pressing it out toward's the edge of the screen. You can also wrap a credit card in the dry cloth, and use that as a way to force out some air bubbles.
If you're not happy with the alignment and/or have anything stuck under there, then it is possible to remove and reapply. Do this very carefully though, by using your nail to lift it up from the corner, taking extra care not to fingerprint that side of the protector. Use the dust sticker to remove any bits. Though again, be as quick as possible as whilst that side of the protector is exposed, more stuff might land there!
Impressions:
From being a long time user of the film screen protectors, those being 'wet installed' etc. I must say I have been converted! I did have my hesitations about using glass protection, as a while back I used one and it failed to impress me. Previously I had found this type of material, glass vs plastic film, would add a mirror-like reflection to the screen, even more so than the Gorilla Glass screen that the device already had. Also, with my love of AMOLED devices I found glass screen protectors would detract from the 'deep black' the screen would display, and make such colours more of a grey, which affected viewing pleasure.
But not with this one!!
Feel - I instantly fell in love with how this looked and felt. It has no loss of sensitivity and I have not felt the need to have to swipe harder or change the way I interact with the phone. It feels just as responsive as it did prior to installation!
Looks - There is no glare/mirroring effect and so as far as it's looks are concerned, it's practically invisible! The screen colours look as vibrant as they did before and blacks still look as deep as they did
Fit - As you can see I have this installed with this rugged case and it fits PERFECTLY. This case slightly lips over and so there is no dust being trapped around the edge of the screen protector. I'd presume it will also be compatible with other cases too, as it is full coverage, going right to the edges with it's own bezel, not just covering the screen.
I highly recommend the use of this screen protector, for the added peace of mind that the screen is further protected against scratches etc.
Any questions please do ask!
@cd993 thanks for the nice review. I also normally don't like the complete glas, but bought a similar one. I'm also quite happy with it except one thing which disturbs me a little bit. Mine has the black frame around it ( which is in itself not a problem) and this is taking away just a tiny bit from the screen (maybe half a millimeter on the left and right). Is it the same with your one ( from the pics it looks like it also has the black frame). That it take away a bit of the screen is only noticeable when using apps which really starting text completely on the left side ( like the netguard log for example )
Sent from my OnePlus 5T using XDA Labs
tbv2005 said:
@cd993 thanks for the nice review. I also normally don't like the complete glas, but bought a similar one. I'm also quite happy with it except one thing which disturbs me a little bit. Mine has the black frame around it ( which is in itself not a problem) and this is taking away just a tiny bit from the screen (maybe half a millimeter on the left and right). Is it the same with your one ( from the pics it looks like it also has the black frame). That it take away a bit of the screen is only noticeable when using apps which really starting text completely on the left side ( like the netguard log for example )
Click to expand...
Click to collapse
Thanks! To be honest I don't think it does. I've just looked at various apps, such as matlog/play store etc and no noticeable screen cut off
cd993 said:
Thanks! To be honest I don't think it does. I've just looked at various apps, such as matlog/play store etc and no noticeable screen cut off
Click to expand...
Click to collapse
Thanks, I maybe give that one a try then . Just to make clear for everybody. The app in the pic I attached in my former screenshot really starts at pixel 0 on the left side... It's really not a lot what's missing....
tbv2005 said:
Thanks, I maybe give that one a try then . Just to make clear for everybody. The app in the pic I attached in my former screenshot really starts at pixel 0 on the left side... It's really not a lot what's missing....
Click to expand...
Click to collapse
Do so, you'll like it!
thanks
Thanks for the review mate!! I've used US's products before and I think they're the best screen protector I've ever used.
Ordered mine 2 days ago and can't wait for it to be delivered, I miss the sensitivity and feel that those usually have.
rvstico said:
Thanks for the review mate!! I've used US's products before and I think they're the best screen protector I've ever used.
Ordered mine 2 days ago and can't wait for it to be delivered, I miss the sensitivity and feel that those usually have.
Click to expand...
Click to collapse
Enjoy!
Would love to get one but ... it seems they don't ship to Mexico and that's a shame :c .-.....
PriPhaze said:
Would love to get one but ... it seems they don't ship to Mexico and that's a shame :c .-.....
Click to expand...
Click to collapse
Email them, perhaps they'd be willing to...
I have applied this protector too....
Always had phones without screenprotector because I hate them... It takes away the feel of the phone... Bubbels underneath glass etc etc.
Bought it because I saw some scratches on the screen coming.
So after this positive review gave it a try. But man I must say it's a great quality.
Applying is very easy off course look for dust... Becaue I had one.... Took it off which is very easy to do... Rinsed it off under water....
Take two was a succes.... Didn't dry it just putt it on the phone and wipe wipe wipe and a lot of patience....and rubbing. It was bubble free.
But glad I did it.... In fact I find the screen better looking.. Bit of 3d effect...
Fp and typing is as normal.
Only con its a bit heavy....
Don't compare this to a 5 dollar screenprotector which is also the reason why I hated them.
*justintime* said:
I have applied this protector too....
Always had phones without screenprotector because I hate them... It takes away the feel of the phone... Bubbels underneath glass etc etc.
Bought it because I saw some scratches on the screen coming.
So after this positive review gave it a try. But man I must say it's a great quality.
Applying is very easy off course look for dust... Becaue I had one.... Took it off which is very easy to do... Rinsed it off under water....
Take two was a succes.... Didn't dry it just putt it on the phone and wipe wipe wipe andota of patience....
But glad I did it.... In fact I find the screen better looking.. Bit of 3d effect...
Fp and typing is as normal.
Only con its a bit heavy....
Click to expand...
Click to collapse
Glad you like it! Yeah it really is a great screen protector, basically looks the exact same with it on and barely noticeable!
tbv2005 said:
@cd993 thanks for the nice review. I also normally don't like the complete glas, but bought a similar one. I'm also quite happy with it except one thing which disturbs me a little bit. Mine has the black frame around it ( which is in itself not a problem) and this is taking away just a tiny bit from the screen (maybe half a millimeter on the left and right). Is it the same with your one ( from the pics it looks like it also has the black frame). That it take away a bit of the screen is only noticeable when using apps which really starting text completely on the left side ( like the netguard log for example )
Sent from my OnePlus 5T using XDA Labs
Click to expand...
Click to collapse
Is your screen protector from spigen?
thanks.
I'm using a chinese version but have some issues. The protector have some kind of bend and it causes a bubble impossible to remove just in the front camera. Because of that my front cam don't focus right.
That's the one:
https://www.aliexpress.com/item/32982692897.html
@cd993 from the pictures you attached it seems the screen protector has real curved edges. Am I right or is just my impression? If you could add more pictures where we can see how curved are the edges without the case, I would appreciate.
I'm looking for a good screen protector that has curved edges so I can use a slim cover.
Currently I have a Cafele full screen protector (bought on AliExpress for 4 USD), which is good and has a nice feeling, looks very similar to this one, but it doesn't have curved edges and because of that it doesn't stick very well in the corners, if I use a slim case.
Thanks.
silmarx said:
@cd993 from the pictures you attached it seems the screen protector has real curved edges. Am I right or is just my impression? If you could add more pictures where we can see how curved are the edges without the case, I would appreciate.
I'm looking for a good screen protector that has curved edges so I can use a slim cover.
Currently I have a Cafele full screen protector (bought on AliExpress for 4 USD), which is good and has a nice feeling, looks very similar to this one, but it doesn't have curved edges and because of that it doesn't stick very well in the corners, if I use a slim case.
Thanks.
Click to expand...
Click to collapse
Apologies, I no longer have this phone!
cd993 said:
Apologies, I no longer have this phone!
Click to expand...
Click to collapse
But can you tell me if you recall if the edges were really curved?
silmarx said:
But can you tell me if you recall if the edges were really curved?
Click to expand...
Click to collapse
Hmm I remember then being curved yes, but no overly so.
Either way I certainly recommend it and fitted it great, as well as being case friendly, in my experience
cd993 said:
Apologies, I no longer have this phone!
Click to expand...
Click to collapse
Hey what's that?? What do you have now?
*justintime* said:
Hey what's that?? What do you have now?
Click to expand...
Click to collapse
Ha! I went for the Oneplus 7 Pro
cd993 said:
Ha! I went for the Oneplus 7 Pro
Click to expand...
Click to collapse
Ghehehe good luck with it. [emoji106]