Guys,
I've tried to update my Android's firmware from v2.2.1 to the ICS rom.
The issue started when I've tried to flash CWR through ODIN.
All procedures have been done: loaded the cooper, and the CWR .tar, put my mobile on Download Mode, plugged USB, Odin showed <1> Added!!! <1> Detected!!! and hit the Start button.
After waiting for about 30min there was no response from ODIN, then, I removed the USB and closed ODIN. After that I turned on my Galaxy Ace and the following scenario came up: an image of a pc connected to phone with exclamation mark in between.
Later I tried to recover my mobile by flashing the firmware of v2.3.6 through ODIN as well. It started well, but, in the middle of the installation it failed.
What can I do?
Please, it's urgent!
Thanks in advance folks!
happened with me a lot....but i usually flash the stock firmware with odin and my phone becomes good as new. try again to flash stock firmware via odin.
if i'm not mistaken maclaw's ics needs gb bootloader, thus need to flash stock gb rom beforehand. u cant just go straight from froyo to ics :/
btw try this.
turn off phone, remove battery, wait for around 5-10 seconds, press three button combination for download mode (vol down+home+power) and while u still holding those three buttons reinsert the battery. device should go into download mode and u should be able to reflash with stock gb rom via odin. and good luck with it.
Related
Hi Everyone,
Need help with my I9100 which doesn't boot. I got this phone yesterday and was using it fine. Today i installed Kies and it prompted to upgrade firmware. I researched and found that it had improvements in battery life and decided to go for it. It downloaded the firmware and everything went fine until it prompted saying firmware upgrade failed and asked me to do firmware emergency recovery.
I googled to see more info regarding this error and couldnt get much information. Decided to go ahead with recovery as instructed. Again i got error " Firmware emergency recovery stopped due to GT-I9199 error". If the problem persistes please contact samsung service center.
Please suggest if this is recoverable error and any links to proceed and have a working phone.
Currently when i power on, i get a logo of phone connected to PC with yellow bang in middle. Any pointers much appreciated....
Thanks.
Don't worry, I think you can fix this yourself using ODIN. I mean, flash a custom rom through Download mode. (Turn the phone off, hold Volume Down + Home + Power for 4 seconds)
In this mode you can flash any kind of rom without doing your phone any harm. Just go to the Rom Development forum and choose your rom. I suggest Lightning Rom, because it uses ODIN, and has a very well-explained tutorial.
You can also flash a stock rom, you can get it from the Stock Rom thread, and flash that through ODIN.
Or get it fixed by Samsung and wait two weeks. (where they use exactly the same program, ODIN, to reflash the stock rom)
Look here
And here
And finally here
If all that doesn't work, take it back to samsung.
Also, KIES is a PoS, use Odin in future
Yep, KIES may look all official and reliable, but it actually seems to brick some SGS2's.
Thanks for the info's. Will try them and update soon.
No luck. I tried multiple times to update ROM using ODIN in download mode. Everytime it says NAND write operation failed and comes out. I am searching to see if any other option left before i take it back to samsung
Don't forget to try it with a different computer. Sometimes it's not the phone, it's the PC or the USB port.
Also, you can try flashing with Heimdall instead of Odin.
First of all;
Yellow triangle means you are running custom kernel/rom.
Press home+volume down and then power, to get into download mode , on your phone. If that works, take battery out, to stop it.
Go to:
Samfirmware.com
Download firmware from there. It is a rar file, I think. Open rar file to see what is in. 5 files? The biggest file has all of the other files in it.
Install via Odin. Select pda in Odin and select the biggest file from the rar.
Put your phone into download mode, connect usb and run Odin.
Adrian.
SGS2 I9100
Lite'nin rom 3.2
Make sure that all kies processes are closed or odin will fail.
Sent from my GT-I9100 using XDA Premium App
Keis? Hmm.
Adrian.
SGS2 I9100
Lite'nin rom 3.2
it gets worse...
my brother let the battery fall out of his S 2 while flashing with odin, now it wont power on in any mode, the PC wont recognise it at all, when i plug in the charger the phone gets hot, but does nothing.... whats the recovery method? or is it dead well and truly...
mightygoose said:
my brother let the battery fall out of his S 2 while flashing with odin, now it wont power on in any mode, the PC wont recognise it at all, when i plug in the charger the phone gets hot, but does nothing.... whats the recovery method? or is it dead well and truly...
Click to expand...
Click to collapse
You can buy a usb jig, specially designed to put you phone into download mode. Search for it on ebay. Take the battery out, plug in usb jig, replace battery and it should boot into download mode. If it does not, then the phone is dead.
Sent from my GT-I9100 using xda premium
Having recently installed a miui rom, i found that my phone has become brocked. I can go to dwonload mode, and I can turn it on but there is only a blank screen. Does anyone know how to unbrick it?
Thanks
go into download mode open up ODIN and flash a stock ROM. Simple as that.
you should buy a jig to get download mode. Did you tried recovery mode ?
Sent from my GT-I9100 using XDA Premium App
nikkox988 said:
you should buy a jig to get download mode. Did you tried recovery mode ?
Sent from my GT-I9100 using XDA Premium App
Click to expand...
Click to collapse
He said he can access Download mode which means he can flash a stock ROM and all will be good.
I can't seem to go into recovery mode
thealmightysaj said:
I can't seem to go into recovery mode
Click to expand...
Click to collapse
to get recovery get into download mode open Odin and flash CF-Root Kernel and then try to get into download mode that way.
I flashed the CF Root Kernel (XW_CLK_KF3), but it failed in Odin
thealmightysaj said:
I flashed the CF Root Kernel (XW_CLK_KF3), but it failed in Odin
Click to expand...
Click to collapse
are you flashing it through PDA? Just checking I didnt on accident once. Also try just flashing a stock ROM.
http://forum.xda-developers.com/showthread.php?t=1224423
onli flashing pda wont work i thinkk... you may need to repartition
go to http://androidflip.com/android-2-3-4-gingerbread-xxkg3-firmware-update-for-samsung-galaxy-s2/
flash it by repartitioning
download the package in it. it worked for me
Where can I find the stock ROM for a Bell Samsung GS2?
try samfirmware.com
they have all of the official released firmwares based on geographical region.
or
http://forum.xda-developers.com/showthread.php?t=1075278
I have unbricked my phone but i can't access the android market, everytime time i open up the app it closes
my t-mobile galaxy s2 is dead after ICS upgrade failed
i am noobi. my galaxy s2 went through 2 stages before becoming dead.
1. i tried to flash I9100XXLPQ_I9100OXALPQ_I9100XXLPQ_HOME.tar using odin. it got stuck in connection mode. then failed. when rebooted the phone, i got a message "firmware upgrade encountered an issue".
2. now, odin still sees it. I tried different ROMs then the phone becomes dead. the phone is dead even after pressing the vol up+vol dn or any other key combination.
Now, windows 7 reports driver error when connecting the phone via usb. Linux sees the Qualcom modem, but heimdall failed to detect the phone. Any suggestion beside throwing my phone in trash is appreciated.
If you can't get into download mode (home/power/volume down), only thing you can try before you send it back to Samsung or get it JTAG repaired is a jig, which unfortunately is unlikely to work. Still worth a try tho.
hbarri said:
i am noobi. my galaxy s2 went through 2 stages before becoming dead.
1. i tried to flash I9100XXLPQ_I9100OXALPQ_I9100XXLPQ_HOME.tar using odin. it got stuck in connection mode. then failed. when rebooted the phone, i got a message "firmware upgrade encountered an issue".
2. now, odin still sees it. I tried different ROMs then the phone becomes dead. the phone is dead even after pressing the vol up+vol dn or any other key combination.
Now, windows 7 reports driver error when connecting the phone via usb. Linux sees the Qualcom modem, but heimdall failed to detect the phone. Any suggestion beside throwing my phone in trash is appreciated.
Click to expand...
Click to collapse
Try uploading a stock kernel first, then try uploading the rom
Do we have to have a jig?
Help me fix my fully bricked i9100
I have flashed the wrong Roms and firmwares in my Samsung galaxy s2 i9100 for several times now my phone doesnt go to the recovery mode. It only goes to the download mode but re flashing the correct new roms and firmwares, nothing actually works! I tried those
Odin shows only FAIL !! when I flash new roms..I ve tried so many roms so far but it only fails
what do I do now??
Try http://sammobile.com for the firmware.
Sent from my GT-I9100 using Tapatalk 2
Samsung Galaxy S2 SPH-D710
Looking for any kinda help...
Tried rooting the above mentioned phone with:
http://forum.xda-developers.com/showthread.php?t=1721229
the odin came back failed. I unpluged and when the phone started it said: Firmware Upgrade encountered an issue. Please select recovery in kies & ... so on..
I can only get into odin donwloading....
The PC is not recognizing the phone either..
Help if you can... Its greatly appreciated...
Thanks,
XraidedX2 said:
Looking for any kinda help...
Tried rooting the above mentioned phone with:
http://forum.xda-developers.com/showthread.php?t=1721229
the odin came back failed. I unpluged and when the phone started it said: Firmware Upgrade encountered an issue. Please select recovery in kies & ... so on..
I can only get into odin donwloading....
The PC is not recognizing the phone either..
Help if you can... Its greatly appreciated...
Thanks,
Click to expand...
Click to collapse
I had the Exact same problem as you this is what you need to do.
1. Take everything out of your phone micro sd ,sim battery
2.Get your Usb Port and connect the first side to your pc but not to the phone
3.Insert Battery
4.Hold the vol down butt and at the same time connect the Other side of the cable into the phone then you will see
DOWNLOAD MODE!!!!!
5.From there install your sock rom again using samfirmware.com
6.Done
Hello,
After flashing my Galaxy S2 i9100G with clockwork recovery mode, it stucked at "yellow triangle" at startup screen and nothing happens. I m unable to star in downloading or recovery mode.
Can anyone please help me to get ridout of this ?
Thanks,
Pratik
pratikkagda said:
Hello,
After flashing my Galaxy S2 i9100G with clockwork recovery mode, it stucked at "yellow triangle" at startup screen and nothing happens. I m unable to star in downloading or recovery mode.
Can anyone please help me to get ridout of this ?
Thanks,
Pratik
Click to expand...
Click to collapse
Sometimes download mode can work even if the screen isn't turning on. You should follow the instructions for download mode and see if Odin recognizes your phone.
if see odin has recognized ur fone, flash it with the stock firmware using odin!
Thanks for the response but I tried several times but phone is not booting up in downloading mode.
Sent from my GT-N7100
Try this (it may or may not work)
Launch PC Odin & get rom ready (I recommend LiteningRom [NB, it is custom rom that can be flashed via Odin]
turn ph off & remove battery...
plug ph into pc (NB, battery still out...)
**now you may need extra set of hands here (I managed it by myself though)**
now, hold the button combo to get ph in to d/l mode...
keeping the d/l button combo depressed... put battery back into ph...
hopefully ph will show d/l mode ready on screen & it will be seen by Odin :fingers-crossed:
(if above worked) flash Litening Rom & count your lucky stars...
NB, this saved me when my S2 had BSOD.... i.e. nothing showed on screen after flashing a recommended kernel (by a more experienced user/member - not the OP)
always read up before doing anything kernel/recovery related
Try USB jig.
Hello xda, first post n00b here,
I recently got my hands on a SIII (lot better then my old htc one V), and I wanted to install cyanogenmod on it. So I installed the i9300 recovery rom on it and for a short while it seemed to work, but when I tryed to sideload cyanogenmod something went wrong. Everytime I rebooted I got thrown into the downloading, do not power off target!!-screen.
I quickly found my mistake, I did not have an i9300 I had an i9305. With some help from the lovely people at #cyanogenmod (shout out to you PsychoI3ob) I figured out I had to flash the stock rom. I could not figure out how to do this with heimdall, so I downloaded Odin. With Odin, everything went right untill it was somewhere around 99%. The write failed. Now the only thing I see when I but the batteries in my phone is: Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again.
So now I would like to know: Did my phone just become a paperweight or is there still anything I can do?
Thanks a lot for reading trough!
If you can get back into download mode by shutting down your phone, and then boot while holding the volume down, home button and power button simultaneously you could try reflashing stock ROM through Odin.
If the phone turns on as soon as you put the battery in then you will have to take the battery back out, and then whilst pressing Vol Down and Home button put the battery in (I've had the same issue on a Galaxy Ace II with the phone booting as soon as the battery was put in, but managed to get back into download mode and reflash by doing as I described)
If you manage to successfully reflash, boot into recovery (turn off, then hold Vol Up, Home and Power) and do a factory reset from there just for good measure.
Good luck :good:
"Firmware upgrade encountered an issue..." It is also download mode. You can use Odin to flash while this screen has been displayed or launch Kies and restore your original firmware by firmware initialization option from tools menu.
Write model name GT-I9305 and your phone serial number (under battery). Kies will check what version of firmware was originally pre-installed on that device. Will download and flash it automatically. After that you can upgrade to newest stock. Write custom recovery via Odin, flash custom rom from CWM.
____________________________________________
P3110 / I9300 / I9100 / NEXUS 5 / iPAD2
S3 stuck in ODIN
OK I've tried everything and read as many threads as I could find. Here's the scenario
- stuck in ODIN mode
- try to get into Recovery mode but it just flashes and goes away and then back into ODIN mode
- KIES sees the phone and I can kick off a firmware upgrade and initialization but I want to try and keep all the data
- I've tried 4 different version of ODIN and stock ROMs from ATT, all FAIL immediately and now the device boots into ODIN mode with Flash Read Failure error
Any ideas?
I didnt understand werry vell but try this if you can enter recover connect your samsung to pc and pull out your files am not shure if you can do this with CWM recovery but you can with twrp then delete everthing (factory reset will keep your files) download offical firmware from sammobile or simmilar and flash it with odin
What was the last thing you did before you got stuck
Edit
I dont know will this make any diffrence but flas other firmware not att