hello, i am a newcomer to android, recently bought a droid razr xt910 off kijiji.
it worked fine but had the latam rom so i couldnt get updates past 2.3.5. So i tried changing to eu using this tutorial vid by razr guy on how to unbrick/ upgrade/ downgrade your razr
however during the setup with the .bat file it said infopreflash validation failure After it finished it ended up boting to the ap fastboot screen. now every boot option and menu leads to it.
i need a fix soon or the phone will run out of charge.
id greatly appreciate it if someone could help me, please
the clock is ticking
since you just got it you might aswell get the new ICS
http://forum.xda-developers.com/showthread.php?t=1643425
you will need RSD Lite, you will find using search on thread
then ap fastboot and flash the rom via RSD Lite..
Dylan Marley said:
hello, i am a newcomer to android, recently bought a droid razr xt910 off kijiji.
it worked fine but had the latam rom so i couldnt get updates past 2.3.5. So i tried changing to eu using this tutorial vid by razr guy on how to unbrick/ upgrade/ downgrade your razr
however during the setup with the .bat file it said infopreflash validation failure After it finished it ended up boting to the ap fastboot screen. now every boot option and menu leads to it.
i need a fix soon or the phone will run out of charge.
id greatly appreciate it if someone could help me, please
the clock is ticking
Click to expand...
Click to collapse
Hi Dylan
Wellcome to XDA and android community
Our Razrs are region signed and you cannot flash another region rom in a latam device.
We have a 2.3.6 firmware to latam devices actualy
You may flash this with rsd lite
http://forum.xda-developers.com/showthread.php?t=1624352
This is a how-to guide for razr
http://forum.xda-developers.com/showthread.php?t=1539192
Cheers
Sent from my XT910 using Tapatalk 2
i can only access the ap fastboot, even if i go to options and click recovery or boot it redirects to ap fastboot
Dylan Marley said:
i can only access the ap fastboot, even if i go to options and click recovery or boot it redirects to ap fastboot
Click to expand...
Click to collapse
You have to start it in ap fastboot mode.
power + vol up + vol down (to turn off and enter bootmenu)
then
vol down (to navigate to ap fastboot) and vol up (to select).
Conect your phone, start rsd lite, unzip the rom I've pointed and flash.
Wait 'till it finish flashing and start the phone. (tip: do not close rsd lite 'till phone reboots again).
Good luck
the phone doesmt show in rsd lite, help
Dylan Marley said:
the phone doesmt show in rsd lite, help
Click to expand...
Click to collapse
What you mean? Are you in ap fastboot mode?
Sent from my XT910 using Tapatalk 2
pedrotorresfilho said:
What you mean? Are you in ap fastboot mode?
Sent from my XT910 using Tapatalk 2
Click to expand...
Click to collapse
same here friend the phone doesnt show in rsd lite. please help me and my razr save us from dying.
Dylan Marley said:
hello, i am a newcomer to android, recently bought a droid razr xt910 off kijiji.
it worked fine but had the latam rom so i couldnt get updates past 2.3.5. So i tried changing to eu using this tutorial vid by razr guy on how to unbrick/ upgrade/ downgrade your razr
however during the setup with the .bat file it said infopreflash validation failure After it finished it ended up boting to the ap fastboot screen. now every boot option and menu leads to it.
i need a fix soon or the phone will run out of charge.
id greatly appreciate it if someone could help me, please
the clock is ticking
Click to expand...
Click to collapse
You need to buy a Motorola Factory Cable. They are very cheap. I had to buy one as well, and it fixed my Razr in Boot Failure.
Buy one here: http://www.ebay.com/sch/i.html?_trk...kw=motorola+factory+cable+&_sacat=0&_from=R40
*Make sure it's the right cord for your device (XT910)* DO NOT BUY FROM CHINA!! (I have had bad experience)
How to use it: http://www.usbstyle.com/cables/moto...able-for-fastboot-mode-unroot-unbrick-rooted/
(Scroll down for instructions)
No need to use RSD Lite, just use Razr Utility 1.82!
Download here: http://rootzwiki.com/topic/37761-droid-razr-utility-182-for-verizon-xt912-models-windows/
Hope I helped!
Related
I was following this video on instruction on unlocking my atrix on youtube titled "Motorola Atrix: Unlock and Upgrade to GB - Unlock P1"
My atrix was already updated to 2.3.4
Now Using RSD Lite.. idk what happened, the process failed.. and everytime I turn on my phone, it tells me "OS not found" or something like that.
It says:
SVF:105:1:2
Failed to boot 0x1000
NO OS detected, going to RSD mode in 5 seconds
Press a key to stop count down
Available Modes are:
1.RSD
2. Fastboot
3. NvFlash
4. BP HW Bypass RSD
5. BP HW BYPASS QC DLOAD
6. BP HW Diag & Boot AP
7. BP HW Bypass BP Only
8. BP SW Bypass RSD
9. Android Recovery
10. Boot Android (No BP)
11. Device UID
12 console=ttyS0, 115200n8
13. Early USB Enumeration
14. BP Tools
Can someone please help my get my phone working again.. I can't even live like a day without my phone. Is my phone hardbricked or is there any way to revive it?
Any help would be appreciated.
Thanks
try the next step
Just continue the fastboot commands and you should be fine, same thing happen to me
Sent from my MB860 using XDA App
Javi97100 said:
Just continue the fastboot commands and you should be fine, same thing happen to me
Sent from my MB860 using XDA App
Click to expand...
Click to collapse
Which fastboot commands, because I tried to use the ones such
fastboot flash preinstall preinstall.img
fastboot reboot
but nothing worked.
Try this
fastboot oem unlock
(Then it will give you a code, and type it again with code at the end)
Then when phones says unlocked
Type
fastboot reboot
Sent from my MB860 using XDA App
cpatel90 said:
Now Using RSD Lite.. idk what happened, the process failed.. and everytime I turn on my phone, it tells me "OS not found" or something like that.
It says:
SVF:105:1:2
Failed to boot 0x1000
Click to expand...
Click to collapse
Guys, where do you get the courage to do the unlock process that bricked so many phones without reading instructions?
When flashing pudding over OTA 2.3.4, Failed to boot is a common error.
You need to redo the fastboot unlock commands and all will be fine.
This is explained in the pudding thread, and gets explained every day again and again with each new thread that newbies create.
xploited said:
Guys, where do you get the courage to do the unlock process that bricked so many phones without reading instructions?
When flashing pudding over OTA 2.3.4, Failed to boot is a common error.
You need to redo the fastboot unlock commands and all will be fine.
This is explained in the pudding thread, and gets explained every day again and again with each new thread that newbies create.
Click to expand...
Click to collapse
Also if you do some looking around you'll find this http://forum.xda-developers.com/showthread.php?t=1182871 which I think was a SUPER easy way to unlock my bootloader and I didn't run into any of the issues that so many have ran into.
From unlocked/rooted GB Atrix
thanks for the help guys.. but i think its over for my phone.
it doesn't even turn on anymore. the green light comes on for one second and turns back off. i think i'll just have to get a new phone.
cpatel90 said:
thanks for the help guys.. but i think its over for my phone.
it doesn't even turn on anymore. the green light comes on for one second and turns back off. i think i'll just have to get a new phone.
Click to expand...
Click to collapse
You weren't a hard brick. You just didn't complete the steps. Did you do something else to it since your initial post? Sounds like your battery is drained, which means you need to charge it externally.
cpatel90 said:
thanks for the help guys.. but i think its over for my phone.
it doesn't even turn on anymore. the green light comes on for one second and turns back off. i think i'll just have to get a new phone.
Click to expand...
Click to collapse
uhh... sounds like your battery is drained. find someone who can charger your battery (another Atrix owner, or a Droid X owner) and try again PROPERLY.
you were trying to flash PREINSTALL to your phone? that is NOT the OS. that roots your phone once it's already installed. you need to install the SYSTEM.img and related files. you really need to read the entire guide as it so far looks like you didn't read anything.
you need to use moto-fastboot to flash System images, not regular fastboot.
http://forum.xda-developers.com/showthread.php?t=1138092
use these images and this guide, which coincidentally warns you NOT to RSD from the stock 2.3.4 and is stickied at the top of the dev forum.
http://forum.xda-developers.com/showthread.php?t=1160408
i seem to have hard bricked my atrix, doing the same thing.. well, my brother did anyway. but i somehow forced it to download mode. and re-flashed it. Works perfectly.
caleb4992 said:
i seem to have hard bricked my atrix, doing the same thing.. well, my brother did anyway. but i somehow forced it to download mode. and re-flashed it. Works perfectly.
Click to expand...
Click to collapse
that's a soft brick.
svf :105.1:2
failed to boot 0x1000
show this..........
i cant to move it to android recovery cause there no option to move
after showing this error automatically switch off my phone.....
any solution
bivrat said:
svf :105.1:2
failed to boot 0x1000
show this..........
i cant to move it to android recovery cause there no option to move
after showing this error automatically switch off my phone.....
any solution
Click to expand...
Click to collapse
Yea, thats a hard brick
Sent from my MB860 using XDA App
bivrat said:
svf :105.1:2
failed to boot 0x1000
show this..........
i cant to move it to android recovery cause there no option to move
after showing this error automatically switch off my phone.....
any solution
Click to expand...
Click to collapse
bivrat,
You've asked this same thing maybe like 5 times already and each time we've told you that there is no fix and you have to get a new phone.
Need urgent reply
Guys.. i have a favour to ask!
m in a search for a second hand moobile and found this ATRIX 4G unlocked edition which has run into this problem!
"A recent Over The Air upgrade 2.3.6 to the phone (which should have been avoided on a rooted phone) has made the phone non working.
The phone does not boot, and displays the message:
Failed to Boot 1...
Entering RSD Mode."
Guys please let me know if this coud be fixed or not, as i am in a real mood to buy this one!
bivrat said:
svf :105.1:2
failed to boot 0x1000
show this..........
i cant to move it to android recovery cause there no option to move
after showing this error automatically switch off my phone.....
any solution
Click to expand...
Click to collapse
Did you try the Unlock v4.2 app from this site? Option 3 of the menu very well might fix it for you. Well worth a shot if you haven't tried it yet.
So I have been trying a bunch of different roms for the RAZR today and I was having problems with the keyboard not working. I decided to try to load CM9, so I read I need to use "safestrap" and not "bootstrap" that I had been using. I downloaded it, installed then tried to boot into recovery and load CM9.
Now the safestrap boot screen appears and says "safe system disabled" "hit search to continue / hit the menu button to boot into recovery" if I hit the menu button it just reboots, if I hit search the screen just goes blank and I have to do a reset to get it to start the process again.
I have RSD but I have never used it before. I have my phone plugged into my computer but my computer doesnt see it.
Help!
dreamsti said:
So I have been trying a bunch of different roms for the RAZR today and I was having problems with the keyboard not working. I decided to try to load CM9, so I read I need to use "safestrap" and not "bootstrap" that I had been using. I downloaded it, installed then tried to boot into recovery and load CM9.
Now the safestrap boot screen appears and says "safe system disabled" "hit search to continue / hit the menu button to boot into recovery" if I hit the menu button it just reboots, if I hit search the screen just goes blank and I have to do a reset to get it to start the process again.
I have RSD but I have never used it before. I have my phone plugged into my computer but my computer doesnt see it.
Help!
Click to expand...
Click to collapse
Whats your razr. Its verizon? If not you should use bootstrap.
Safestrap is for verizon razr. But some uses bootstrap on it.
You have to put ur razr in ap fastboot mode: power+vol up+vol down in order to flash with rsd lite
Choose a stock rom to your razr and flash it. Make sure flash correct rom
Cheers
Sent from my XT910 using Tapatalk 2
I have the Verizon RAZR.
So my computer does not recognize the phone when in AP Fastboot, but it does recognize it when its in BP SDF flash. What am I doing wrong?
dreamsti said:
I have the Verizon RAZR.
So my computer does not recognize the phone when in AP Fastboot, but it does recognize it when its in BP SDF flash. What am I doing wrong?
Click to expand...
Click to collapse
Uninstall all motorola software, reinstall motocast 1.29 or newer then connect ur razr.
Use rsd lite 5.7 and make sure you got correct sbf file
You may have corrupted drivers.
Cheers
Cheers
Enviado de meu XT910 usando o Tapatalk 2
Do I need to install anything else other than those 2 things? It still doesnt work.
Would having Samsung drivers effect anything? I have a Galaxy Nexus too.
dreamsti said:
Would having Samsung drivers effect anything? I have a Galaxy Nexus too.
Click to expand...
Click to collapse
Sometimes it brokes motorola drivers. Doing what I said should work.
Edit:
BTW what's the version you were and what's the version you're trying to flash?
Some versions cannot downgrade when the one you're trying to flash have a lower security.
I was running Gummy when everything went wrong. Loading safestrap is when I started having the current problems.
I uninstalled the Samsung drivers, and loaded both RSDLite 5.7 and the Moto driver you suggested and RSD will not see my phone in AP Fastboot, but it will when in BP SDF flash. Very confusing.
I will load the latest version of GB when I can get my computer to see my phone in AP Fastboot.
Now my computer is trying to install the flash MZ600 driver and error's out. I googled MZ600 and it says its a Xoom driver???
dreamsti said:
Now my computer is trying to install the flash MZ600 driver and error's out. I googled MZ600 and it says its a Xoom driver???
Click to expand...
Click to collapse
Yup. You've a driver problem, better unistall others devices you may have.
Or, do it in other pc, like a notebook.
So I finally got the drivers working and now RSD see's my phone when in AP Fastboot, but I get an error when flashing the file. This is the error I get.
"Failed flashing process. 22/23 flash "radio.img" -> Phone returned FAIL."
It was flashing for about 5 minutes before I got this error.
Edit: I'm using the file from this thread.
http://rootzwiki.com/topic/13566-droid-razr-fastboot-file/
Blur_Version.6.12.173.XT912.Verizon.en.US
I think the battery went dead, ugh. Ill recharge and report back.
I would like to know when we keep our put our razr into boot mode (volup+voldown+power) there are various options available,
if someone could please explain the following modes and how to use it would be great, some difference between AP and BP.?
>BP SBF FLASH?
>BP ONLY
>BP HW DIAG & BOOT AP
>BP TOOLS
rachit2588 said:
I would like to know when we keep our put our razr into boot mode (volup+voldown+power) there are various options available,
if someone could please explain the following modes and how to use it would be great, some difference between AP and BP.?
>BP SBF FLASH? - -Allows you to reload a phone that won't boot by using RSD Lite and your PC via USB. Even though your PC won't recognize the phone via USB it will if you go into this mode.
>BP ONLY
>BP HW DIAG & BOOT AP
>BP TOOLS
Click to expand...
Click to collapse
I put in the one I know. LOL
85gallon said:
I put in the one I know. LOL
Click to expand...
Click to collapse
yea thats smart, ... but still I would like to know.!!
rachit2588 said:
I would like to know when we keep our put our razr into boot mode (volup+voldown+power) there are various options available,
if someone could please explain the following modes and how to use it would be great, some difference between AP and BP.?
>BP SBF FLASH?
>BP ONLY
>BP HW DIAG & BOOT AP
>BP TOOLS
Click to expand...
Click to collapse
SBF mode is akin to the old bootloader menu and loads firmware in a different format from a single file using a service software utility
AP Fastboot is the new bootloader menu for loading firmware via the command line fastboot interface. This is where the firmware is flashed as discreet image files.
BP tools contains hardware diagnostic and repair options and are used to repair your dead phone with aid of specific software , ( usually they first dowgrade your boot version and then proceed with other instals) you get options like repair , testpoint etc , USB BP bypass etc.. I dont have much info on this as its used by your moto service centre.
As far as you are concerned you will be using the AP fastboot mode when ur phone is totally bricked to flash your fastboot files..
SAJdroid said:
SBF mode is akin to the old bootloader menu and loads firmware in a different format from a single file using a service software utility
AP Fastboot is the new bootloader menu for loading firmware via the command line fastboot interface. This is where the firmware is flashed as discreet image files.
BP tools contains hardware diagnostic and repair options and are used to repair your dead phone with aid of specific software , ( usually they first dowgrade your boot version and then proceed with other instals) you get options like repair , testpoint etc , USB BP bypass etc.. I dont have much info on this as its used by your moto service centre.
As far as you are concerned you will be using the AP fastboot mode when ur phone is totally bricked to flash your fastboot files..
Click to expand...
Click to collapse
Thanks for a good info. Need more details on BP tools.?
Yea SBF format...I am using that for my MB525. Wonder why they discarded this format for razr
Sent from my XT910 using xda app-developers app
rachit2588 said:
Thanks for a good info. Need more details on BP tools.?
Yea SBF format...I am using that for my MB525. Wonder why they discarded this format for razr
Sent from my XT910 using xda app-developers app
Click to expand...
Click to collapse
BP tools , even I am trying to find out more info..
bp tools
I downgraded my HD to the 4.0.4 thinking the reason why the phone wouldn't install the QC Interface because it was on 4.1.1, not the case tho this phone still will not install the drivers, Tried a virtual port with the phone being connected in MPT connections, still can't connect to a serial port, the device is in Usb debugging, tried booting into reg mode, then back into bp tools nothing, guess the next search is for a HD Rom that may have the bp tools compiled into it.. Any help appreciated.
thanks !!
I am having a problem. I was trying to upgrade to Jelly bean 4.1 on this Atrix 4g. I tried to go through the steps that it gave online with the CM10 n Cyro and all. Long story short it couldn't find the rom within the zip or something of that nature. In other words, it screwed me over. I can't get back into recovery. It's been giving me this error:
SVF 108:1:2
Failed to boot 3
Starting RSD mode
Before it was giving me just:
Failed to boot 4
Starting RSD mode
I had tried reseting to factory through the moto-fastboot but of course it failed. I have been tryin like crazy to flash various SBF from 2.3.5 to 2.3.6. I was originally at 2.3.6 but for what ever reason when I try the RSD lite it gives me the error after it executes "Phone did no re-enumerate after RAM downloader was sent". (0x703e). I have been reading forums literally all day. Perhaps I am not understanding something therefore I am missing it but maybe one of you guys could help me out with this? Maybe there is a real simple fix or maybe I completely ruined it? Either way it would be nice to get some help on this. Basically when I was trying to upgrade to 4.1 I followed "How to upgrade the Atrix 4G to Android 4.1.1 Jelly Bean via CyanogenMod 10" off of the androidauthority website. I got to step 9 but it couldn't find the ROM, by then it was too late.
UPDATE: So I got just that and RSD was flashing it until it reached yet another error:
failed flashing process. Failed flashing process. Phone[0000]: error switching phone BP pass through mode (0x70BE); phone disconnected.
Help?
majorrazer said:
Help?
Click to expand...
Click to collapse
I'm no expert, you can wait for an expert response but what i couldnt understand is why you try to flash a SBF. The manual you refer to is a CWM based installation, with a zip file, not a SBF.
So do you have CWM recovery flashed? Do you have the related zip file downloaded to sdcard?
saldirai said:
I'm no expert, you can wait for an expert response but what i couldnt understand is why you try to flash a SBF. The manual you refer to is a CWM based installation, with a zip file, not a SBF.
So do you have CWM recovery flashed? Do you have the related zip file downloaded to sdcard?
Click to expand...
Click to collapse
I don't have anything flashed at the moment. I can't boot into anything at the moment. I am confused perhaps with what will solve my problem.
majorrazer said:
I don't have anything flashed at the moment. I can't boot into anything at the moment. I am confused perhaps with what will solve my problem.
Click to expand...
Click to collapse
Do you have an unlocked bootloader? Does the word "Unlocked" appear when you power the phone on? You must have an unlocked bootloader for sure. IF not, you must unlock it.
his is the guide you were following;
http://www.androidauthority.com/atrix-4g-mb860-android-4-1-1-jelly-bean-cyanogenmod-10-cm10-106639/
As said there, it requires unlocked, rooted Atrix with with ClockworkMod Recovery installed
I guess you can still unlock the bootloader and install cwm recovery. Just search and find instructions.
HEY
i have the same problem also.... and the same error...
is your phone fix already?
could you tell me how?
SVF: 108:failed to boot 3 starting RSD mode
Hi,
I have Atrix 4G AT&T, last night rooted it and from recovery mode install custom rom cm-7.2.0-olympus after reboot its not booted and showing "SVF: 108:failed to boot 3 starting RSD mode". Removing battery also not solve this problem, Andriod recovery mode also not working by pressing down volume key on restarting. RSD Lite procedure also not working for my phone. RSD Lite 5.6 or other versions (i tried most of all) also not deducted my phone when i connected to PC in Fastboot mode. I m new and have not to much information about software version of this Motorola Atrix 4G but before its bricking mode it was on Gingerbread 2.3.6.
I have also tried "cmd prompt" stock frame version and other procedures but all failed to start my Phone to normal.
salimdawar said:
Hi,
I have Atrix 4G AT&T, last night rooted it and from recovery mode install custom rom cm-7.2.0-olympus after reboot its not booted and showing "SVF: 108:failed to boot 3 starting RSD mode". Removing battery also not solve this problem, Andriod recovery mode also not working by pressing down volume key on restarting. RSD Lite procedure also not working for my phone. RSD Lite 5.6 or other versions (i tried most of all) also not deducted my phone when i connected to PC in Fastboot mode. I m new and have not to much information about software version of this Motorola Atrix 4G but before its bricking mode it was on Gingerbread 2.3.6.
I have also tried "cmd prompt" stock frame version and other procedures but all failed to start my Phone to normal.
Click to expand...
Click to collapse
Did you unlock the bootloader the right way?
Sent from my MB860 using xda app-developers app
palmbeach05 said:
Did you unlock the bootloader the right way?
Sent from my MB860 using xda app-developers app
Click to expand...
Click to collapse
Not fully under stand "unlock bootloader" the right way? As mention earlier i m not an expert or more knowledge about Rooting and hacking of Andriod Phones, Please tell me in Details, thanks
salimdawar said:
Not fully under stand "unlock bootloader" the right way? As mention earlier i m not an expert or more knowledge about Rooting and hacking of Andriod Phones, Please tell me in Details, thanks
Click to expand...
Click to collapse
did you flash pudding sbf via rsd and use fastboot to oem unlock?
Sent from my MB860 using xda app-developers app
palmbeach05 said:
did you flash pudding sbf via rsd and use fastboot to oem unlock?
Sent from my MB860 using xda app-developers app
Click to expand...
Click to collapse
No i didnt use RSD methode because RSD Lite not deducting my Phone, tried different versions of RSD for flash pudding, I have Windows 8-64bit.
Also Flash the Mobile throw following procedure
Boot the Atrix into “Fastboot Mode” (hold power + vol down)
plug your Atrix into your PC via USB
Navigate to your fastboot folder via command prompt
type “moto-fastboot flash boot boot.img” press enter
type “moto-fastboot flash system system.img” press enter
type “moto-fastboot -w” press enter
type “moto-fastboot reboot” press enter.
But it also not Boot my phone in normal, Its stuck in Start menu,
SVF 108:1:2
Failed to boot 3
Starting RSD mode
salimdawar said:
No i didnt use RSD methode because RSD Lite not deducting my Phone, tried different versions of RSD for flash pudding, I have Windows 8-64bit.
Also Flash the Mobile throw following procedure
Boot the Atrix into “Fastboot Mode” (hold power + vol down)
plug your Atrix into your PC via USB
Navigate to your fastboot folder via command prompt
type “moto-fastboot flash boot boot.img” press enter
type “moto-fastboot flash system system.img” press enter
type “moto-fastboot -w” press enter
type “moto-fastboot reboot” press enter.
But it also not Boot my phone in normal, Its stuck in Start menu,
SVF 108:1:2
Failed to boot 3
Starting RSD mode
Click to expand...
Click to collapse
ok so its telling you what to do. Since you haven't flashed a sbf, chances are you are not unlocked, so how do you expect to flash anything on a locked device?
Did you install motorola device manager for the drives?
Sent from my MB860 using xda app-developers app
palmbeach05 said:
ok so its telling you what to do. Since you haven't flashed a sbf, chances are you are not unlocked, so how do you expect to flash anything on a locked device?
Did you install motorola device manager for the drives?
Sent from my MB860 using xda app-developers app
Click to expand...
Click to collapse
Yes already install this file from Net
"Motorola_End_User_Driver_Installation_5.1.0_64bit "
and not expect any thing else about flashing of my device.
Before Motorola Atrix 4G, i were used in passed Samsung S1, S2, S3, & T989 (T-Mobile S2 version). All these andriod sets were very easily hack or Root and can install Roms easily .
But Moto Atrix 4G can me upset and sad.
kindly help me to re-connect my self to the andriod world by this Motorola Atrix 4G, thanks
Hey guys I'm having trouble getting to RSS mode my phone comes on then it says entering nv flash recovery mode then the phone dies so I need help trying to get into my phone to flash the sbf file
Sent from my GT-N7105 using XDA Premium 4 mobile app
Need Help regarding Motorola Atrix Mb 861.
salimdawar said:
No i didnt use RSD methode because RSD Lite not deducting my Phone, tried different versions of RSD for flash pudding, I have Windows 8-64bit.
Also Flash the Mobile throw following procedure
Boot the Atrix into “Fastboot Mode” (hold power + vol down)
plug your Atrix into your PC via USB
Navigate to your fastboot folder via command prompt
type “moto-fastboot flash boot boot.img” press enter
type “moto-fastboot flash system system.img” press enter
type “moto-fastboot -w” press enter
type “moto-fastboot reboot” press enter.
But it also not Boot my phone in normal, Its stuck in Start menu,
SVF 108:1:2
Failed to boot 3
Starting RSD mode
Click to expand...
Click to collapse
I need your help regarding Motorola Atrix Mb 861. My phone is not boot and show..
SVF: 108:1:2, Failed to boot 3
Starting RSD mode.
also not able to hard reset. My phone detail are.
My model is KT Atrix MB861
Not sure which is the build number
s/w version: 4.5.2A-KT-75
Android version: 2.3.4
Kernel version: 2.6.32.9-00001...
Please Help regarding that matter.....
kamal.navigator said:
I need your help regarding Motorola Atrix Mb 861. My phone is not boot and show..
SVF: 108:1:2, Failed to boot 3
Starting RSD mode.
also not able to hard reset. My phone detail are.
My model is KT Atrix MB861
Not sure which is the build number
s/w version: 4.5.2A-KT-75
Android version: 2.3.4
Kernel version: 2.6.32.9-00001...
Please Help regarding that matter.....
Click to expand...
Click to collapse
Were you bootloader unlocked before getting this message?
Hi guys,
My Motorola BackFlip MB300 can access to Bootloader Init and can flash firmware by RSD tool but when it reboot only can display to Motorola Logo and silent forever. I change some firmware but it didn't any change. Hope that everyone will have right way to help me! Thank for read my post!
CyanogenVietNam said:
Hi guys,
My Motorola BackFlip MB300 can access to Bootloader Init and can flash firmware by RSD tool but when it reboot only can display to Motorola Logo and silent forever. I change some firmware but it didn't any change. Hope that everyone will have right way to help me! Thank for read my post!
Click to expand...
Click to collapse
all i think first was flashing SBF file on AP Fastboot mode
is it failed?
666satyr666 said:
all i think first was flashing SBF file on AP Fastboot mode
is it failed?
Click to expand...
Click to collapse
Yes, man! It's also fail...Plz help me with other way...
CyanogenVietNam said:
Yes, man! It's also fail...Plz help me with other way...
Click to expand...
Click to collapse
firmware for your device.
You need to download these things...
RSD Lite 4.5.7
AT&T Stock Android 2.1 Blur v3.0.1390 - Original SBF by Skrilax_CZ @ ModMyMobile
And if you're doing this and haven't attempted root yet, or would just like to wipe your device through and through, HERE are the Moto USB drivers. Make sure to get the correct installer for x86 or x64.
Install your USB Drivers (if you haven't already)
Install RSD Lite
Turn off your backflip
Plug the USB cable into the phone and computer
Open the keyboard and press J+D+Power simultaneously and let up when you see the blue recovery screen with the black moto batwings. In the bottom left corner of the screen it will say in white letters "USB init mode"
Now when the phone boots to the recovery screen, Windows will begin installing a driver for the MSM720x flash recovery mode.
After the driver has successfully installed, open RSD Lite
Upon opening RSD Lite, you should notice ONE connected device in the table below. If not, post what you did exactly and we can help
Now that the device is showing in RSD Lite, click the "..." browse button to point to the Android 2.1 Blur 3.0.1390 image you downloaded earlier
Once that's selected, press start to start flashing your phone.... DO NOT UNPLUG UNTIL IT'S FINISHED.
Once finished, it will reboot itself and you should be presented with the Android Setup after a minute or two.