[Q] Kernel Panic with Many ROMs. - Galaxy S II Q&A, Help & Troubleshooting

I am using SGS2 i9100 and rooted and CWM installed as follows:
1. PC Odin Flash LPB Firmware (ICS 4.0.3).
2. PC Odin Flash CF Root LPB Kernel.
3. Mobile Odin Flash Stock LPB Kernel to remove Yellow triangle.
4. Mobile Odin Flash CF Kernel again to get CWM Recovery as well as root.
So far everything is OK. I can boot to recovery and installed CheckROM v6. Perfect no problems.
Then decided to try MIUI (ICS) when it was released. After complete wipe, ROM installation completed and on reboot > Kernel Panic Upload Mode. Couldn't boot to recovery Just to Download Mode. Had to follow steps 1 to 4 again to get Phone working with root and recovery. Tried a couple of times with MIUI from different sources like miui.us or miuiandroid.com but same result. So back to CheckRom v6 which works without problem.
With recent better ICS ROMs available, tried to install Omega v1.0. Again Kernel Panic Upload Mode. Followed steps 1 to 4 again. Tried Omega 12.0 used by lot of people. Again Kernel Panic Upload Mode. Tried PC Odin Flash of Siyah Kernel. Got the Siyah screen to show on bootup but this remained a while ... ROM did not boot and then screen turned to Kernel Panic Upload Mode after waiting a couple of minutes.
After again doing steps 1 to 4 I am back on CheckROM v6 which works flawlessly.
Why can I not use any rom which tons of users are using? Is there a hardware peculiarity which is preventing this? Should I try out old or new or ICS bootloaders? I don't want to mess with bootloaders as I hear these can hard brick the device.
Any suggestions?
Thanks.
PS: My Complete Wipe steps are:
1. Remove user data/Factory reset.
2. Clear Cache
3. Clear Dalvik Cache.
4. Optionally Format system partition in mounts and storage.

The reason is obvious ....Why old LPB???? Stay away.....
Start again from the GB rom better 2.3.5 from odin
Root with cf root and flash any rom what you want from CWM...
No need to change bootloader again...the one you get along with the gb rom is enough further for all

OK I have KE8 (Gingerbread ROM 2.3.3 which is latest for my location) downloaded. Will a PC Odin flash of this remove my current troublesome bootloaders? Or should I download another GB Rom 2.3.5 or newer for PC Odin Flash?
PS: I used LPB assuming that an ICS Rom would give me the bootloaders which would not give me headaches from installing custom ROMs from XDA here. If someone could explain to me where my logic went wrong?
ZACQ8 you called LPB old, but wouldn't it be newer than the 2.3.5 GB ROMs?

NeoMustain said:
OK I have KE8 (Gingerbread ROM 2.3.3 which is latest for my location) downloaded. Will a PC Odin flash of this remove my current troublesome bootloaders? Or should I download another GB Rom 2.3.5 or newer for PC Odin Flash?
PS: I used LPB assuming that an ICS Rom would give me the bootloaders which would not give me headaches from installing custom ROMs from XDA here. If someone could explain to me where my logic went wrong?
ZACQ8 you called LPB old, but wouldn't it be newer than the 2.3.5 GB ROMs?
Click to expand...
Click to collapse
you can flash the one which you are having now, but make sure CF-root is available for that to Root and install CWM, for your further flashing of ROMs,
yes that will replace the bootloader, but doesnt matter, it will be ok for all custom roms, (unless some Rom devs insist to replace bootloader first for their Roms)
I told the LPB is the old in the sence, it is old beta release among the ICS versions. Kernel Panic was highly reported while using this version.
Kernel panic Mode is hardly reported when people are coming from GB roms and installing Roms from CWM. that is why I sugested flash a GB rom from ODIN then move to any ROM through CWM.
You can also flash and try latest ICS version from ODIN.

Cool. That's the task for tonight then.
Sent from my GNex on AOKP.

if you are flashing a custom ICS ROM take the LP9 version,
one custom ROM with LP8 version has gaven me once the Kernel Panic
Goodluck

Thanks that worked. Installed Omega 1.0. Downloading Omega 2.1. No kernel panics. So from now the phone shoul dbe trouble fre hopfully.

wen u get prblms instead of keeping on flashing jus stop an ask..
flash stock gb after wipe..
then root properly..
don go for any rcs,beta,alpha root release....
then its a good idea to flash stock ics ...
wen u get a clear pic,u can go for aokp,aosp which will b diff...
bottom line kno some basics instead of jumping far away......cheerz

Looks like I'm in the same situation, I had used odin to flash with I9100_CODE_I9100XXLP2_CL57619_REV02_user_low_ship.tar.md5 back in Jan/Feb and flashed it with CF-Root-SGS2_XX_OXA_LP2-v5.2-CWM5 kernel.
I was then able to flash new ROMS no problem with CWN
Then flashed the other day with the latest Ressurection Remix 2.2 and am getting the dreaded "Kernel Panic...."
So I'm back to the I9100_CODE_I9100XXLP2_CL57619_REV02_user_low_ship ROM.
My plan is to flash it with a 2.3.6 ROM using odin, then apply the CF-Root kernel and from there I'm hoping I can then apply Ressurection Remix ROM.
I'm just a bit unsure of which versions of the ROMS to use, I haven't been able to find a guide to selecting the correct versions for my phone. Any pointers would be greatly appreciated.

Related

Stuck in Kernel Panic mode

Hi guy's, was running the original Criskelo ICS rom, noticed there was an update available for it (while browsing on the phone). Jumped onto the PC but accidentally installed the version for a Galaxy Note or something like that. It was just showing a funny screen that would bleed from black to white as it got hot. Complete newbie mistake.
I'm pretty sure that's all sorted and in the past now (but maybe there is some hangover from it?). I installed the stock ICS rom, then flashed a kernal with CWM. Now, whenever I try to install the new version of Criskelo, it flashes fine and shows no errors but everytime it goes to start it goes into kernal panic mode. Each time I need to flash the stock rom, then a rooted kernal and try again.
I have tried flashing Criskelo in the CWM app, on both the internal storage and the external SD card, have also booted into CWM mode and wiped the cache, restored factory data and wiped the davlik cache, and tried to install)
I have searched but most responses on the subject suggest re-flashing which i've tried 4 times now.
just tried to put the older Criskelo rom on and it's done the same thing, kernal panic mode.
The kernal i'm using is the one I used originally when I 1st had Criskelo rom running.
bckup ur efs and stuff an i think format the mem card an phone on pc then flash a stock on it,an if ur imei or pcode messed ,ull have a bckup u made b4 so jus do the correct stuff...sometimes u hav to take risk wen ur careless wiv the device.......hope it helps
thanks for the reply. Can I just remove the memory card and format the phone only (memory card is a 64gb)? What shall I use to format the phone? I've lost SD cards in the past using the format that's part of windows. Would hate for anything to happen to the phone.
Shall I do this process http://www.jayceooi.com/2011/07/18/how-to-hard-reset-samsung-galaxy-s-ii/
pull out your battery and put back after sometime, and vol-down+Home+Power
select a latest GB rom from my link of stock roms in my signature and falsh from ODIN, and root with C-froot
zaheedahmed said:
pull out your battery and put back after sometime, and vol-down+Home+Power
select a latest GB rom from my link of stock roms in my signature and falsh from ODIN, and root with C-froot
Click to expand...
Click to collapse
I've got no problem installing a standard official rom and then rooting the phone. The problem is when I want to then flash a custom rom
i've just wiped the phone, formatted it and the SD card. Still the same issue. I don't understand what's going on. I might try a different custom from and see if the same thing is happening.
have you flashed anything from ODIN befor?
this time you must install an official rom from ODIN, still dubt feel free to ask
i'm flashing the original rom via odin. That's installing fine and i'm flashing the rooted kernal through odin, that's also working. When I try to flash the Criskelo rom i'm using CWM to flash it. I don't think the rom can be flashed by odin can it? It's a zip file rather than .tar files.
If there is a way to do it via odin, i'll try that?
zaheedahmed said:
have you flashed anything from ODIN befor?
this time you must install an official rom from ODIN, still dubt feel free to ask
Click to expand...
Click to collapse
Are you able to get downlaod mode with vol-down+home+power?
download this one http://skywanker.net/download/downl...9100_DBT_I9100XWLA4_I9100XXKI4_I9100DBTKH1.7z
and extract it then you will get a file ...MD5, select that file from ODIN PDA section and flash...
Read the Guide from the thread on my signature how to use the ODIN
---------- Post added at 07:02 PM ---------- Previous post was at 06:58 PM ----------
oho ....you are no more stuck in the Kernel Panic now, only when you install that perticular ROM?
then you try flashing Siyah kernel from ODIN after installing that ROM
---------- Post added at 07:06 PM ---------- Previous post was at 07:02 PM ----------
if Criskelo rom is an ICS one use this one http://gokhanmoral.desean.net/siyahkernel/v3.0/Siyah-v3.1b1.tar
flash from ODIN,
i've just tried to install another custom rom, this time it just stayed on the boot screen rather than kernal panic.
I'm wiping it back to stock (ICS rom), then i'll install the kernel you just linked me to and try criskelo again, is that what your suggesting?
edit.....
Just installed the standard rom. Flashed the Siyah kernal via odin and it re-booted into kernal panic upload mode. That's not happened before. The 1st time I flashed the kernal it didn't do this.
I'm really confused...
Escy said:
i've just tried to install another custom rom, this time it just stayed on the boot screen rather than kernal panic.
I'm wiping it back to stock (ICS rom), then i'll install the kernel you just linked me to and try criskelo again, is that what your suggesting?
edit.....
Just installed the standard rom. Flashed the Siyah kernal via odin and it re-booted into kernal panic upload mode. That's not happened before. The 1st time I flashed the kernal it didn't do this.
I'm really confused...
Click to expand...
Click to collapse
"standard ROM" you told is ICS or GB?...it must be ICS, otherwise wont work,
I told you the Siyah kernel link which I sent you only use with an ICS ROM,
you start from biginning again, flash the official ROM (not the ICS a GB rom) and Root with CF- kernel and install your desired custom ROM, should be working fine...
Crickelo V38 is not an ICS ROM it is GB rom...
Siyah 3.x and higher is for ICS.
Siyah 2.6.14 and lower is for GB.
There are also ICS only versions of SpeedMod and other kernels.
You must pay attention to what version of Android a kernel is meant for before flashing.
I'm trying to install this rom. CriskeloServanRom SGS2 4.0.3 oficial Firm XXLPQ
The 'original' rom i'm installing is a ICS one for my phone. That flashes fine every time. When I flash a rooted kernel that also works fine, it's just flashing with CWM that's giving me these troubles
edit...
The rooted kernel is CF-Root-SGS2_XX_OXX_LPB-v5.2-CWM5-PROPER.tar which matches the LPB code on my phones firmware.
Since i've been trying to flash the Siyah kernal, it's giving me the same "kernel panic upload mode". When I was flashing the CF-Root-SGS2_XX_OXX_LPB-v5.2-CWM5-PROPER.tar kernel that wasn't a problem. The problem came when I tried to flash roms with CWM
Escy said:
I'm trying to install this rom. CriskeloServanRom SGS2 4.0.3 oficial Firm XXLPQ
The 'original' rom i'm installing is a ICS one for my phone. That flashes fine every time. When I flash a rooted kernel that also works fine, it's just flashing with CWM that's giving me these troubles
edit...
The rooted kernel is CF-Root-SGS2_XX_OXX_LPB-v5.2-CWM5-PROPER.tar which matches the LPB code on my phones firmware.
Since i've been trying to flash the Siyah kernal, it's giving me the same "kernel panic upload mode". When I was flashing the CF-Root-SGS2_XX_OXX_LPB-v5.2-CWM5-PROPER.tar kernel that wasn't a problem. The problem came when I tried to flash roms with CWM
Click to expand...
Click to collapse
please stay away form the ICS leaked unofficial ROMs, LPB is the old and it gave similar kernel panic trble for many people....
you flash an officilal ICS rom (preferebly XXLPQ, then root with C-f root then flash your favourite ROM
Thank you for all the help your giving me. I'm currently downloading this one, is that correct?
XXLPQ
Firmware info
PDA:XXLPQ
PHONE: XXLPQ
Date: 09/03/2012
Android 4.0.3
Multi-CSC Package (AUT, CMF,COA, COS, CYO, DNF, ERO, EUR, FOP, GBL, MSR, MTL, NEE, ORG, ORS, PAN, PHE, SEB, SMO, TMS, TOP, TPH, TRA, TRG, TSR, TWO, VOM, VVT, XEH, XEO, XSK): Download Mirror: Download Mirror 2: Download Mirror 3: Download Torrent: Download
PLQ ROM :http://www.filefactory.com/file/c4c70a8/n/I9100XXLPQ_I9100OXALPQ_XEO.rar
LPQ CF-ROOT :http://download.chainfire.eu/152/CF-Root/SGS2/CF-Root-SGS2_XX_XEO_LPQ-PROPER-v5.4-CWM5.zip
Sorry to keep asking questions and making myself annoying. Just want to check, the 2 links you've given are for a rom and a rooted kernel to suit that rom?
Thank you for all your help, sorted now.
...for the love of God and mother of all things, it's KERNEL not KERNAL. Man, I know this isn't a spelling class, but c'mon...
maybe this was the culprit....the dreadful KERNAL...

[Q] Flashing white screen on boot

hi guys, first post
ive had my rooted galaxy s2 with the latest siyah kernel 3.3.2, i had cwm recover 5 and rom manager
i tried to flash cyanogen mod through rom manager, following the steps it gave me, i downloaded the files through rom manager and went through all the prompts till i clicked agee to go into recovery mode.
once it did that the phone shut off but would not turn on again so i went to turn on manually, it loads the samsung galaxy screen with the yellow triangle but goes straight into a white flashing screen.
Ive tried taking the battery out, leaving it and putting it back in again, still a flashing screen,
check what i9100 you have and download correct cm9.
using cwm format data system cacha sdcard dalvik
flash cm9 using cwm
rommanager doesnt work on GS2
atifsh said:
check what i9100 you have and download correct cm9.
using cwm format data system cacha sdcard dalvik
flash cm9 using cwm
rommanager doesnt work on GS2
Click to expand...
Click to collapse
i have the international 19100T
ahh rats i should have known rom manager does not work, , im just stuck in a white flash screen on boot up, cant get to cwm, although i can get into odin
would reflashing my kernel on odin get me through? everything is back up onto my sd card.
Try flashing a kernel first, and if that doesn't work, flash a rom in Odin, re-root your phone & restore your backup. But yeah, don't use Rom Manager with a kernel that has CWRecovery. One or the other. Rom Manager has a habit of doing stuff like what's happened to you on SGS2's which also have CWRecovery installed.
MistahBungle said:
Try flashing a kernel first, and if that doesn't work, flash a rom in Odin, re-root your phone & restore your backup. But yeah, don't use Rom Manager with a kernel that has CWRecovery. One or the other. Rom Manager has a habit of doing stuff like what's happened to you on SGS2's which also have CWRecovery installed.
Click to expand...
Click to collapse
awesome, I tried flashing the latest siyah kernel, the one that i already had on my phone before the problems, that didn't do anything to get me through, any suggestions on which kernel/rom to flash?
because you are on siyah and im not comfortable with that, please flash a stock kernel or cfroot kernel and format system data partitions after that.
now flash any official stock ICS or GB rom using Odin.
atifsh said:
because you are on siyah and im not comfortable with that, please flash a stock kernel or cfroot kernel and format system data partitions after that.
now flash any official stock ICS or GB rom using Odin.
Click to expand...
Click to collapse
ohh sweet baby jesus im i flashed a cf kernel and now im into cwm on 4.0.1.5, can i just normal reboot my phone now?
No need to format anything. Given you want to use CM9, I'd recommend you flash CM9 Resurrection Edition in Odin, put the latest CM9 nightly & Gapps on your internal/external SD card then flash that nightly & Gapps in CWM (read the first page of the CM9 discussion thread thoroughly & follow the instructions to the letter. From there you can stick with the CM9 stock kernel or flash whatever other kernel you want to use (provided it's CM9 compatible).
From then on, if you want to flash CM9 nightlies, do it via CWM/CWRecovery, just don't use Rom Manager this time I use CM9 as well & I have it frozen because I use Siyah (which has CWM).
MistahBungle said:
No need to format anything. Given you want to use CM9, I'd recommend you flash CM9 Resurrection Edition in Odin, put the latest CM9 nightly & Gapps on your internal/external SD card then flash that nightly & Gapps in CWM (read the first page of the CM9 discussion thread thoroughly & follow the instructions to the letter. From there you can stick with the CM9 stock kernel or flash whatever other kernel you want to use (provided it's CM9 compatible).
Click to expand...
Click to collapse
alrighty! thanks for the info, is cf kernel compatible with cm9? i want to just have one kernel that'll handle most roms, any suggestions?
ive reloaded my old stable phone version, the version i saved before trying to flash cyanogen mod with rom manager, this version has siyah and stock rom, back to square one *phew*
i still say wipe first, cm9 will come with its own latest cwm that can be used to flash any custom roms after.
flashing via odin version is easy and fool proof as it has everything bundled for correct working of cm9.
If you flash CM9 the CM9 kernel will overwrite/replace your CFRoot kernel, which is fine. As I said in my previous post you can stick with that if you're happy with it, or you can flash any other kernel that's CM9 compatible.
No suggestions/recommendations. Because your experience will not be the same as someone else's using a given rom or kernel. If you want to go down that path, try some kernels to find one you like. To see if a kernel is compatible with CM9, read the the dev thread devoted to the kernel in question.
OK. Given you're back @ square one, Atifsh is right when he says flashing the Resurrection version (Odin version) then flashing Gapps/nightly from there is probably a good way to go for you. Once you've done that, you'll be able to flash CM9 nightlies via CWRecovery. As said previously, read that first page of the CM9 discussion thread/instructions thoroughly before you do anything.
keegan25 said:
alrighty! thanks for the info, is cf kernel compatible with cm9? i want to just have one kernel that'll handle most roms, any suggestions?
ive reloaded my old stable phone version, the version i saved before trying to flash cyanogen mod with rom manager, this version has siyah and stock rom, back to square one *phew*
Click to expand...
Click to collapse
Something similar happened to me too. I flashed stock XWLPG, then siyah 3.3.2 and did a factory reset. After that, got stuck in a flashing white screen after the yellow triangle.
What I did: boot on download mode, flash XWLPG over PC Odin once more, did a full wipe BEFORE flashing siyah and then siyah. Everything went ok this time, but eventually I found out that every time I do a factory reset after siyah that problem would occur.
Regards,
Sent from my GT-I9100 using XDA
keegan25 said:
i have the international 19100T
ahh rats i should have known rom manager does not work, , im just stuck in a white flash screen on boot up, cant get to cwm, although i can get into odin
would reflashing my kernel on odin get me through? everything is back up onto my sd card.
Click to expand...
Click to collapse
exact same problem, except i can't put it into download mode?
i know it's powerbutton vol down but it's not working? any ideas?
acbutcher91 said:
exact same problem, except i can't put it into download mode?
i know it's powerbutton vol down but it's not working? any ideas?
Click to expand...
Click to collapse
Power + vol down + home key?

[Q] Need help with rooting [official ICS 4.0.3][UCLE5]

Hello guys, So I'm fairly new to rooting (first android/smartphone/ but good experience with PCs) and was wondering if anyone could help me out. I'm using the ICS 4.0.3 build from kies, with the UCLE5, and build number IML74k.CLE5.
*from reading the stickies I've learned to NOT use ROM manager, galaxys2root.com, and to not use the STOCK ICS method as it has a brickbug ( the ones on forum)
Last night I tried rooting my phone by using Doomlord's guide but it didn't work ( I had unknown sources, and USB debugging on*but my phone was on and not on download mode or anything* )
Then I tried SuperOneClick root and it was just stuck on one of the steps, and the only way to stop it was to end task the program and ADP...any tips on what I'm doing wrong? Sorry for being a nub lol
*please move to Q and Q accidently posted in general section
Just use Odin to flash any ics kernel u want.
so I guess Ill try to flash using step 3. on http://forum.xda-developers.com/showthread.php?t=1285894 using ODIN3, then install a kernel ( i want to use 3.3d Siyah ) and then flash a custom ROM (like semi_v17) *the guide from here http://forum.xda-developers.com/showthread.php?t=1650948 correct?
I also want to add that after i Root using 2c.) How to root by flashing Entropy512's Return/Unbrick to Stock, Kernel + Rooted System Package with Modem using Odin3 One-Click Downloader (Windows) that method, I boot into 3E recovery and perform data/factory wipe, wipe cache, dalvik and reset extweaks profiles...then install semi_v17 ROM while in recovery mode and done? Just making sure before I do anything with my phone
I know that relying on the sticky posts leaves some confusion because of Gingerbread and ICS versions. The Entropy512 stock plus root is a Gingerbread firmware with stock kernel and root. If you go that route, you then need to install a Gingerbread custom kernel, and then you can flash Semi from ClockworkMod Recovery if that is what you want.
In my opinion, since you are already on UCLE5 stock, the best route would be to flash the UCLE5 stock plus root package that you can download from the development section, and then install a custom ICS kernel. I know you were trying to avoid the Emmc Superbrick Bug, but since you have stock UCLE5 with the stock kernel on the phone now, you already (supposedly) have the Emmc Superbrick Bug present in the stock kernel. All the instructions needed to install a custom kernel are contained in the OP of the UCLE5 stock plus root thread.
If you have additional questions, just ask.
creepyncrawly said:
I know that relying on the sticky posts leaves some confusion because of Gingerbread and ICS versions. The Entropy512 stock plus root is a Gingerbread firmware with stock kernel and root. If you go that route, you then need to install a Gingerbread custom kernel, and then you can flash Semi from ClockworkMod Recovery if that is what you want.
In my opinion, since you are already on UCLE5 stock, the best route would be to flash the UCLE5 stock plus root package that you can download from the development section, and then install a custom ICS kernel. I know you were trying to avoid the Emmc Superbrick Bug, but since you have stock UCLE5 with the stock kernel on the phone now, you already (supposedly) have the Emmc Superbrick Bug present in the stock kernel. All the instructions needed to install a custom kernel are contained in the OP of the UCLE5 stock plus root thread.
If you have additional questions, just ask.
Click to expand...
Click to collapse
So I flash the build from this [Heimdall][Odin][Stock][Root]UCLE5 Stock ICS with Root..(no need to flash according to thread)
pick one of the the three kernels (prob going with AJ siyad) and install using Odin lite..then ROM? (like Semi v17?) it gets confusing at some parts cause on the Stock ICS + root section is says to wipe before flashing if coming from another base (im guessing since im on the UCLE5 base i dont need too)
AHomelessGuy said:
So I flash the build from this [Heimdall][Odin][Stock][Root]UCLE5 Stock ICS with Root..(no need to flash according to thread)
pick one of the the three kernels (prob going with AJ siyad) and install using Odin lite..then ROM? (like Semi v17?) it gets confusing at some parts cause on the Stock ICS + root section is says to wipe before flashing if coming from another base (im guessing since im on the UCLE5 base i dont need too)
Click to expand...
Click to collapse
Yeah just use mobild odin to flash a kernel and then boot into recovery then wipe then flash semi. I really wish we could update those stickies. They are pretty confusing
One last question...sorry for being a complete noob lmao after I get the kernel, I boot into CWM recovery wipe...and use mobile odin to flash semi?
AHomelessGuy said:
One last question...sorry for being a complete noob lmao after I get the kernel, I boot into CWM recovery wipe...and use mobile odin to flash semi?
Click to expand...
Click to collapse
once you have CWM, you use CWM to flash roms.....
Pirateghost said:
once you have CWM, you use CWM to flash roms.....
Click to expand...
Click to collapse
OK so i got the siyad kernel installed now with the phone stuff wiped (no apps installed yet, not even google account set up) so just put the ROM i want into SD card boot into recovery mode, and install zip from SD card?
AHomelessGuy said:
OK so i got the siyad kernel installed now with the phone stuff wiped (no apps installed yet, not even google account set up) so just put the ROM i want into SD card boot into recovery mode, and install zip from SD card?
Click to expand...
Click to collapse
yes
Thanks everyone everything seems to be working fine reinstalling my apps now and setting up my phone
**EDIT: I have noticed that my buttons on the bottom aren't as bright as they used to be..gonna go look for solutions/problems causing it

Need help flashing s2 for the first time

My friend wants me to flash custom rom to his s2.I have xperia x10 and galaxy nexus with me.Both i have flashed.So i have some experince with flashing but i dont see bottloader unlocking here or one click root ad all so i wanna confirm the steps here beore i do anything stupid
so are these the steps:
1.Root your stock phone with CF-Root 5.6 from http://forum.xda-developers.com/showthread.php?t=1103399
2.Then copy GT-I9100 Resurrection Remix JB v3.1.3 from http://forum.xda-developers.com/showthread.php?t=1436854 to the sd card
3.Get into cwm recovery and flash this rom after a clean wipe
4.Flash Dorimanx 7.44 after a reboot
Is this it?
aswinrulez said:
My friend wants me to flash custom rom to his s2.I have xperia x10 and galaxy nexus with me.Both i have flashed.So i have some experince with flashing but i dont see bottloader unlocking here or one click root ad all so i wanna confirm the steps here beore i do anything stupid
so are these the steps:
1.Root your stock phone with CF-Root 5.6 from http://forum.xda-developers.com/showthread.php?t=1103399
2.Then copy GT-I9100 Resurrection Remix JB v3.1.3 from http://forum.xda-developers.com/showthread.php?t=1436854 to the sd card
3.Get into cwm recovery and flash this rom after a clean wipe
4.Flash Dorimanx 7.44 after a reboot
Is this it?
Click to expand...
Click to collapse
Yeah, all good but, have you read this?
Is your device a GT I9100? Are you on 4.0.4? Got the brick bug? You know siyah is a safe kernel?
gastonw said:
Yeah, all good but, have you read this?
Is your device a GT I9100? Are you on 4.0.4? Got the brick bug? You know siyah is a safe kernel?
Click to expand...
Click to collapse
what if im flashing to 4.2.1 rom?this issue is with ics only right?
aswinrulez said:
what if im flashing to 4.2.1 rom?this issue is with ics only right?
Click to expand...
Click to collapse
The thing is where you're flashing from.
And yes, only 4.0.4's kernel's dangerous.
gastonw said:
The thing is where you're flashing from.
And yes, only 4.0.4's kernel's dangerous.
Click to expand...
Click to collapse
ok i dont have the phone yet..so will confirm its once i get it.
This issue only happens when i flash to ics rom right?not when i flash from stock ICS to JB ?
aswinrulez said:
ok i dont have the phone yet..so will confirm its once i get it.
This issue only happens when i flash to ics rom right?not when i flash from stock ICS to JB ?
Click to expand...
Click to collapse
If you want to go from stock ICS to stock JB you have no need to root.
All you do is simply reboot into download mode (Power on using Volume Up + Home + Power) then flash the JB md5 file via ODIN.
Once you have flashed the file you may find system wont boot into rom (this is normal). Just reboot into download mode and flash latest version of Siyah kernel (.tar file) which will be Siyah v6 beta4 (or above). This will give you cwm recovery, better battery life, root access, SU etc.
Go and have a look at some topics/search etc, All the info you need is already on here and if you try and take some shortcuts you may run into problems or even possibly brick your device so take some time and learn.
PS. Yes the eMMc brick bug is part of stock 4.0.4 kernel so just dont go into stock recovery. You can also brick device by your flash process getting interrupted so make sure you have drivers installed correctly (install kies) and taht you're not running any other programs while flashing and also that you have at least 55% battery.
It's a very good thing you are reading before getting the bad boy you intend to flash.
See the thing about this bug is when you make a back up, wipe things up from the recovery, and flash via oding. Once you do the wipes, you are kinda screwed.
Now, you got a couple of choices here:
1) Your device arrives with 4.0.4 ICS, flash siyah kernel (I'll get you off the hook).
2) Arrives with 4.0.3, you are good to go, no danger.
3) You can try mobile odin, it flashes with its own kernel and, apart from being fast, it's easy.
4) If you get a gingerbread version, you good as well.
That being said, I'd advice you to play with it for a couple of days instead of flashing right away.
Check out some videos, read something about ExynosAbuse (It'll get you rooted with one click) and revolv around the q&a section looking for "not to do list".
good luck and remember, keep on reading.
Sent from the little guy
TheATHEiST said:
If you want to go from stock ICS to stock JB you have no need to root.
All you do is simply reboot into download mode (Power on using Volume Up + Home + Power) then flash the JB md5 file via ODIN.
Once you have flashed the file you may find system wont boot into rom (this is normal). Just reboot into download mode and flash latest version of Siyah kernel (.tar file) which will be Siyah v6 beta4 (or above). This will give you cwm recovery, better battery life, root access, SU etc.
Click to expand...
Click to collapse
Thanks a lot for all your help
the ressurection remix rom i downloaded came as zip file.I can flash it from cwm itself right?
and regarding the kernel im a bit confused between siyah and dorimanx .I know it depends on phone but what would u suggest?ur personal choice
and i need one more help.I need a vanilla jb rom.Not too much bloatware and with less bugs as possible and tweaked for performance and battery.The problem is net speed is very very low...trust me..i cannot try most of them unless i wait for weeks.So if anyone can suggest i can download that alone and do
yeah, via recovery. Read sonething about cmw.
About custom ROM, can't tell you what to flash, do sone diggin in the android development sectio, whatch some vids, It's all here at xda.
Sent from the little guy
gastonw said:
yeah, via recovery. Read sonething about cmw.
About custom ROM, can't tell you what to flash, do sone diggin in the android development sectio, whatch some vids, It's all here at xda.
Sent from the little guy
Click to expand...
Click to collapse
Thank you
don't mention it.
keep reading & happy flashing.
Sent from the little guy

My s2 won't boot any custom roms

Ok before we start, I have looked and tried everything I can find so I will post what I have done after I post my issue. (I know I'm new but I've been using this site a lot lately I just never signed up)
Alright.
My S2 gt-i9100 running ICS 4.0.3 XXLPB
I can root it with cf mod, no problem and confirmed that the root is working properly.
I use CWM recovery. Every single time I've tried to flashboot a custome rom, from Res Remix to straight up cm10 to other jelly bean mods, all the "top" mods suggested in articles, though it says successful, It always, always gets stuck on the Galaxy s2 screen with the yellow triangle. It does not go black, it just stays on that screen, I've left it for as long as 2 hours and it does not do anything and does not let me back into recovery mode. (download mode yes)
I have, multiple times, re-installed stock rom, re-rooted etc...
cleared cache and davik cache, factory reset and format system (prior to flashing the custome roms and sometimes right after as some suggest)
I even tried a complete wipe of the sd card, system, then reflashed stock rom. It always works to return to stock rom and to root it, but nothing else. It seems every solution I find on this site, and many others are point to the above things I have tried all with a slight variety. I have tried many different custom roms,
I'm lost what to do next? I can't find any other information, my binary count is up to 18 now and none of it has worked.
Which kernel are you using?
tejasrm said:
Which kernel are you using?
Click to expand...
Click to collapse
I'm sorry, I thought I mentioned all the info I had.
My current kernel version for ICS is 3.0.15-I9100XXLPB
The kernels I have tried when booting res remix are both Dormanx(sp?) and CM10.1, also tried cm10.1 with another rom.
Sorry I added info, not sure which one you wanted
bbnuck said:
I'm sorry, I thought I mentioned all the info I had.
My current kernel version for ICS is 3.0.15-I9100XXLPB
The kernels I have tried when booting res remix are both Dormanx(sp?) and CM10.1, also tried cm10.1 with another rom.
Sorry I added info, not sure which one you wanted
Click to expand...
Click to collapse
1) re- install stock ICS 4.0.3 rom vide ODIn.
2) use the tar file of siyah kernel v4.1.5 or 5.0.1 to root ur phone vide Odin.
3) now use the siyah kernel v4.1.5/5.0.1 recovery to flash any custom rom of ur choice by fallowing the install instruction of the same carefully
Sun90 said:
1) re- install stock ICS 4.0.3 rom vide ODIn.
2) use the tar file of siyah kernel v4.1.5 or 5.0.1 to root ur phone vide Odin.
3) now use the siyah kernel v4.1.5/5.0.1 recovery to flash any custom rom of ur choice by fallowing the install instruction of the same carefully
Click to expand...
Click to collapse
ohh, yes the Siyah kernel, I failed to mention that i tried rooting using the siyah kernel early on and it would get stuck on the boot screen and even ICS wouldn't work. now on the other hand, this was one of my early attempts and i've tried everything else twice so I will try this option again and get back thanks
I have now tried to boot kernel Siyah 5.0.1 twice and it gets stuck on the kernel boot screen after the samsung s2 screen (the one with the yellow triangle) The screen is a ying-yang symbol with pink/purple lighting. I have left it on for 10 minutes and it stays on that screen. I have removed the battery and put it back in and now it doesn't even get past the s2 bootup screen, I left it for a couple minutes, still nothing. Reboot the phone again and now it's in Kernel Panic Upload Mode... Going back to stock rom. I'll try to find a 4.1.5 siyah kernel and try that one and see if it does anything different.
Sun90 said:
1) re- install stock ICS 4.0.3 rom vide ODIn.
2) use the tar file of siyah kernel v4.1.5 or 5.0.1 to root ur phone vide Odin.
3) now use the siyah kernel v4.1.5/5.0.1 recovery to flash any custom rom of ur choice by fallowing the install instruction of the same carefully
Click to expand...
Click to collapse
Alright, after what happened in the previous message, I have download siyah kernel 4.1.5 and have attempted to flash via odin to root my phone. It did not work either, same issue as 5.0.1. back to stock rom/rooted with cf-root
Try dorimanx ver. 7+ tar or zip
Sent from my GT-I9100 using xda premium
stopro said:
Try dorimanx ver. 7+ tar or zip
Sent from my GT-I9100 using xda premium
Click to expand...
Click to collapse
Just tried dorimanx version 7.50, gets stuck on the bootlogo screen, similar to what siyah was doing.
edit: Also tried dorimanx 8.1, same thing.
Edit: Tried dorimanx 8.3, flashed through cwm recovery this time, still does the same thing
Mate OK download gskernel viper script download syiah 4+ flash boot should work
Sent from my GT-I9100 using xda premium
stopro said:
Mate OK download gskernel viper script download syiah 4+ flash boot should work
Sent from my GT-I9100 using xda premium
Click to expand...
Click to collapse
hi, i have a problem close to the problem here. i recently soft bricked my phone ,sgs2 gti9100 with jellybean 4.1.2. so i tried installing a custom rom named neatrom. after installation the phone reboots and stays in the flashing android sign. it stays like that until the battery runs out. do you think i should change kernals or flash stock rom?
Najahmas said:
hi, i have a problem close to the problem here. i recently soft bricked my phone ,sgs2 gti9100 with jellybean 4.1.2. so i tried installing a custom rom named neatrom. after installation the phone reboots and stays in the flashing android sign. it stays like that until the battery runs out. do you think i should change kernals or flash stock rom?
Click to expand...
Click to collapse
hi mate sorry for late answer but first instal good stock rom by odin then instal best out there kernel for s2 dorimanx but there is 3 versions of it 8.x for stock 9.x mali v2 mean old jb and 10.x mali v3 for latest jb and kk good luck
Najahmas said:
hi, i have a problem close to the problem here. i recently soft bricked my phone ,sgs2 gti9100 with jellybean 4.1.2. so i tried installing a custom rom named neatrom. after installation the phone reboots and stays in the flashing android sign. it stays like that until the battery runs out. do you think i should change kernals or flash stock rom?
Click to expand...
Click to collapse
And don't forget to go in recovery mode and wipe out the dalvik memory under advanced. After wiping dalvik/clearing user data and formatting your phone, reinstall the rom of your choice (that's compatible with the phone)
you can also install siyah 6 and flash kitkat directly from recovery.
Then it would use kitkats kernel and bootup the rom
thank you guys for your replys. i will try what you suggested and get back to you

Categories

Resources