Please help me,my hw rev is 2.3 and firmware is 11141.If i press vol+ and power then insert usb cable then the phone will boot up normally.Is i press vol+ only then insert usb cable it will vibrate once,then after one minute vibrate again and then boot up.
What are the exact steps,installed linux too yesterday for dd and now can;t figure how to enter qualcomm mode...
I have the same problem on my lumia been trying last few hours with out luck i think its a release before nokia updated to dload, i cant even flash in ncs when it goes to reboot the device it come up with Qualcomm cdma technologies msm as a unknown device
OS VERSION: 7.10.7720.68
Firmware revision number: 1600.2475.7720.11414
Hw Revision Number: 112.1402.2.3
Bootloader Version:7.35.0.0
Chip SOC version 0.74.2.1
These are my readings,so hw rev 2.3,fw rev below 11500,what is the problem
Phone is branded Orange FR but not sim-locked.
os version 7.10.8773.98
firmware revision number 1600.2487.8107.120.70
hardware revision 112.140.2.3
radio software version 1.6.00.24
radiohardware 8255
bootloader version 7.35.0.0
chip SOCversion 0.74.2.1
locked to orange tmobile
Well,nobody can give a hint?
When i hit vol+ and plus usb lsusb in linux shows:
Bus 002 Device 006: ID 045e:041e Microsoft Corp.
Well thing is i could not get at all in bootloader mode,as whenerver i would press vol+ it would looong vibrate.
So i flashed the unbranded earlier firmware 412,it worked,now my phone is sim-locked(seems like the ex-owner unlocked it =)) and now when i hit vol+ button it will get a short vibration and go in bootloader that seems to be nokia dload Bus 002 Device 008: ID 0421:05ee Nokia Mobile Phones
So i am sim-locked now,and seems that even if i had hwrev 2.3 and early firmware i did not got an qualcomm bootloader.
**** this,i will unlock then seel this and get the good android back.
Btw anyone know where i can sim-unlock lumia 800 from orange fr?
Dum3 said:
Please help me,my hw rev is 2.3 and firmware is 11141.If i press vol+ and power then insert usb cable then the phone will boot up normally.Is i press vol+ only then insert usb cable it will vibrate once,then after one minute vibrate again and then boot up.
What are the exact steps,installed linux too yesterday for dd and now can;t figure how to enter qualcomm mode...
Click to expand...
Click to collapse
did you finally figure out how QSPT can recognize lumia 800?
thanks
Related
hi,
i am trying to unlock bootloader as per the guides given on this forum. when i get to s1tool part to identify if its factory sim unlocked or otherwise, i switch off the phone, hold the back button and plug in the usb cable. computer recognizes semc flash device and green led switches on at phone. however, s1tool which is already running doesnt show any output and within 5 seconds green led turns off on phone.
am i missing something? gordon gate drivers are installed.
x10 mini
e10i
firmware: 2.1-update1
baseband: m76xx-tsncjolym-53404015
kernel: 2.6.29
build number: 2.1.1.a.0.6
just fixed the problem. i had perhaps the wrong version of s1tool which didnt have the identify button. found another one which had identify button and worked seamlessly
hello there!
i have a problem with this device.
i can't flash / unlock. all the drivers are ok, NSS PRO detects phone in normal mode, read all infos, but when choose OSBL mode, screen goes black, short vibrate and nothing happens after. phone is not detected anymore, but in device manager, there is "Qualcomm CDMA Technologies MSM" with an yellow exclamation mark. i tried this on 2 pcs WIN7, 2 laptops WIN7, 1pc WINXP. no luck. i even run ubuntu into a virtual machine. it displayed "Qualcomm CDMA Technologies MSM" , i done the connection, but the drive Qualcomm MMC does not appear in device utility.
NCSD Version: 1.9
SW Version: 1750.0805.8773.12220
HW Version: 112.1402.2.3
am i elligible to flash phone?
yes you are...
Follow this
http://forum.xda-developers.com/showthread.php?t=1669498
thank you for reply. i done that before opening thread. all drivers installed, but still no luck. phone goes in OSBL mode, but can't find any driver
PS: NSS can't detect phone as "nand disk" because of drivers, i guess.
lumia
if your phone doesnt come up as a flash disc then your not able to flash a custom rom regardless if it is detected as qualcomm msm, as i have found with few lumias i have had there seems to be a version of the boot loader which was just before nokia went to dload.
rob:good:
can i flash a custom rom with "traditional" softwares, like phoenix, jaf, ncs?
kaytar said:
thank you for reply. i done that before opening thread. all drivers installed, but still no luck. phone goes in OSBL mode, but can't find any driver
PS: NSS can't detect phone as "nand disk" because of drivers, i guess.
Click to expand...
Click to collapse
be sure you are running NSS as admin
good luck
hi all,
i just want to see which bootloader i have on my 710, but combination VOL+ POWER then plug in USB doesn't work,
even tryed VOL+ VOL - / VOL+ VOL - POWER, i have the short vibration but as soon as i plug in computer, windows phone load.
i am with Win7 and my phone has been updated recently via Zune.
any advice ?
bootloader
what are you trying to achieve here are you trying to check which bootloader you have or try to flash a custom rom or even sim unlock the device
to get the phone into flash mode its vol + and then power short vibration then plug usb lead in the computer should then detect it. all fails get nokia care suite flash the old firmware that has the unlocked bootloader, you could also plug your phone in as normal then load nss and choose the osbl option then click the arrow that will force the phone into flash mode
rob :good:
thx for the info, i'm trying first to check which boot-loader i have, but i didn't install nokia care suite yet. that's probably why the computer doesn't find the drivers and the phone boot normally in windowsphone. maybe i will install a custom rom to be more comfortable. anyhow it was not simlocked...
Im trying to get my Lumia 800 into recovery mode. This is what i do:
(I use Nokia Care Suit to update to WP7.8)
1. disconnect USB
2. Power off device
3. hold VOL UP button
4. keep holding VOL UP and insert USB cable
5. keep holding VOL UP till i feel a vibration.
6. Pray it will all go well.
My prayers have not helped. Everytime the phone vibrates again and does a normal startup.. What am i doing wrong?
Frimware revision number: 1750.0805.8773.12220
Hardware revision number: 112.1402.2.3
Qualcomm bootloader
Windows 8 x64 & Linux Ubuntu. Both dont work.
Edit:
Windows device manager shows a "Windows Phone" under undefinded. But that disappears after a few second as my Nokia Lumia 800 reboots. Then it is recognised as a Lumia 800.
Twiggie said:
Im trying to get my Lumia 800 into recovery mode. This is what i do:
(I use Nokia Care Suit to update to WP7.8)
1. disconnect USB
2. Power off device
3. hold VOL UP button
4. keep holding VOL UP and insert USB cable
5. keep holding VOL UP till i feel a vibration.
6. Pray it will all go well.
My prayers have not helped. Everytime the phone vibrates again and does a normal startup.. What am i doing wrong?
Frimware revision number: 1750.0805.8773.12220
Hardware revision number: 112.1402.2.3
Qualcomm bootloader
Windows 8 x64 & Linux Ubuntu. Both dont work.
Click to expand...
Click to collapse
In Nokia Care Suite drivers folder (C:\Program Files (x86)\Nokia\Nokia Care Suite\Drivers) try to install the drivers again, for me it works
Thank you for your help. But unfortunately it does not work.
Everytime i try to get into recovery mode, the phone does connect, i hear a connection sound on my Windows 8 machine. Then the phone restarts into normal mode and zune starts.
I had the same issue...
And in Nokia Fuse, the device is available, but in the combobox of Nokia Care Suite, it doesn't appear...
Anyone can help us?
Twiggie said:
Thank you for your help. But unfortunately it does not work.
Everytime i try to get into recovery mode, the phone does connect, i hear a connection sound on my Windows 8 machine. Then the phone restarts into normal mode and zune starts.
Click to expand...
Click to collapse
It could be that you're using the wrong format of driver. I had to install the x64 driver. check the computer you're on and install the x64 or x32 driver for it.
next, why are you trying to access recovery mode? you dont need to - with these drivers Nokia Care Suite does it itself.
ccmiller said:
It could be that you're using the wrong format of driver. I had to install the x64 driver. check the computer you're on and install the x64 or x32 driver for it.
next, why are you trying to access recovery mode? you dont need to - with these drivers Nokia Care Suite does it itself.
Click to expand...
Click to collapse
Thank you for your answer.
I have Win 8 x64, so i installed the x64 version of the drivers. But no luck.
When i try to use Nokia Care Suit, the programe looks for the latest software (7.8) then it wants to install it on the phone, restarts te phone and then i get a message that the connection has been lost. And i need to turn off the phone, and do that whole VOL UP thing again. But the computer never ever recognices the phone in recoverymode. The Lumia 800 just boots up normally.
Watch out before flashing and losing a lucky qualcomm bootloader
Twiggie said:
Im trying to get my Lumia 800 into recovery mode. This is what i do:
(I use Nokia Care Suit to update to WP7.8)
1. disconnect USB
2. Power off device
3. hold VOL UP button
4. keep holding VOL UP and insert USB cable
5. keep holding VOL UP till i feel a vibration.
6. Pray it will all go well.
My prayers have not helped. Everytime the phone vibrates again and does a normal startup.. What am i doing wrong?
Frimware revision number: 1750.0805.8773.12220
Hardware revision number: 112.1402.2.3
Qualcomm bootloader
Windows 8 x64 & Linux Ubuntu. Both dont work.
Edit:
Windows device manager shows a "Windows Phone" under undefinded. But that disappears after a few second as my Nokia Lumia 800 reboots. Then it is recognised as a Lumia 800.
Click to expand...
Click to collapse
same happening with me...all things same...just i have lumia 710...please help
atlast this worked for me
http://forum.xda-developers.com/showthread.php?t=1702815
you have to first upgrade to nokia dload using this...then all will be fine...
Hi everyone
I think you guys can help me with this:
Sanei N10 3g with qualcomm snapdragon is bricked.
All this happend when I pressed vol- vol + and power all together, some window popped up and I had a new drive, but when I tried to turn sane i on notthing happend.
When I press the power button nothing happens, when I connect it on USB port it is recgonized as Qualcomm USB HD QLoader 9008(on COM port 3)
When I install Live Suite 1.07 or 1.09 it is recgonized as vid_1f3a_pid_efe8 but it always gives me code 10(device cannot start) which is actually right, I cannot start my sanei.
I unsolderd the battery and when I solderd it back notthing happend but i got a new device (HD AUDIO MODEM DEVICE), something like that but I cannot find the drivers.
I also used Qpst tools and it is recgonized as phone in download mode??? What is this?
I have downloaded a new firmware from sanei website, but dont now what to do with it. There is no .img file(except boot and recovery)
Now it just lays on my table.
Please help
ivko1982 said:
Hi everyone
I think you guys can help me with this:
Sanei N10 3g with qualcomm snapdragon is bricked.
All this happend when I pressed vol- vol + and power all together, some window popped up and I had a new drive, but when I tried to turn sane i on notthing happend.
When I press the power button nothing happens, when I connect it on USB port it is recgonized as Qualcomm USB HD QLoader 9008(on COM port 3)
When I install Live Suite 1.07 or 1.09 it is recgonized as vid_1f3a_pid_efe8 but it always gives me code 10(device cannot start) which is actually right, I cannot start my sanei.
I unsolderd the battery and when I solderd it back notthing happend but i got a new device (HD AUDIO MODEM DEVICE), something like that but I cannot find the drivers.
I also used Qpst tools and it is recgonized as phone in download mode??? What is this?
I have downloaded a new firmware from sanei website, but dont now what to do with it. There is no .img file(except boot and recovery)
Now it just lays on my table.
Please help
Click to expand...
Click to collapse
you can find the answer to unbrick the device here
http://www.forum.tabletworldstore.co...ch-tablet.html