Hi.i flashed a kernel and after that phone turned off! i tried to reset but didnt work.when i plug the usb cable the red led turns on in both pc and charger!i cant access to fastboot mode or flashtool what should i do guys?and sorry for my English!
what kernel have you flashed, did you flash a kernel for the S, or for an other phone, did flash the kernel matching your firmware, give me some more info please
Sent from my LT26i using xda app-developers app
JoelChrist_ said:
what kernel have you flashed, did you flash a kernel for the S, or for an other phone, did flash the kernel matching your firmware, give me some more info please
Sent from my LT26i using xda app-developers app
Click to expand...
Click to collapse
ive flashed Advanced Stock ICS Kernel for Xperia S my firmware was ics too
matin_08 said:
ive flashed Advanced Stock ICS Kernel for Xperia S my firmware was ics too
Click to expand...
Click to collapse
Have you tried hard reset ? hold on power + volume up button till the phone vibrate 3 times then try to connect to computer again.
Sent from my LT26i using Tapatalk 2
lilude56214 said:
Have you tried hard reset ? hold on power + volume up button till the phone vibrate 3 times then try to connect to computer again.
Sent from my LT26i using Tapatalk 2
Click to expand...
Click to collapse
Doesnt Work
I got that problem too when I was flashing kernel but I had locked bootloader. So I used PC companion to "repair" my phone.
custom kernels are only for unlocked bootloaders.turn off your phone and flash a stock .tft file's kernel via flashtool (press and hold vol down when plug)
Sent from my LT26i using xda app-developers app
EDIT 2: I GOT INTO FASTBOOT!!!!
Hard reset your phone (Volume up + power until phone vibrates 3 times)
Plug into PC
Hold Volume up and power, but as soon as the phone vibrates/red light goes up, REMOVE POWER BUTTON, but HOLD VOL UP.
You should be in Fastboot.
I tried reflashing Doom's kernel, but it doesn't work gah. Will try more.
FYI, flashboot is the same procedure, but hold volume down + power all the way.
Edit 5: Any expert can help with this error message? Trying to relock bootloader/reflash stock to get it PCC to recover.
26/032/2012 00:32:26 - ERROR - ERR_SEVERITY="MAJOR";ERR_CODE="0019";ERR_DYNAMIC="SIN header verification failed";
Basically, it refuses to flash and is stuck at:
26/032/2012 00:32:58 - INFO - Opening device for R/W
26/032/2012 00:32:58 - INFO - Reading device information
EDIT I GOT IT TO WORK
ME 1, SONY 0 (To the 3 guys who followed, you'll know that this is my 2nd phone. Sony replaced my first bricked one)
http://forum.xda-developers.com/showthread.php?t=1766892 <-- FLASH THIS ONE.
Snowstormzzz said:
EDIT 2: I GOT INTO FASTBOOT!!!!
Hard reset your phone (Volume up + power until phone vibrates 3 times)
Plug into PC
Hold Volume up and power, but as soon as the phone vibrates/red light goes up, REMOVE POWER BUTTON, but HOLD VOL UP.
You should be in Fastboot.
I tried reflashing Doom's kernel, but it doesn't work gah. Will try more.
FYI, flashboot is the same procedure, but hold volume down + power all the way.
Edit 5: Any expert can help with this error message? Trying to relock bootloader/reflash stock to get it PCC to recover.
26/032/2012 00:32:26 - ERROR - ERR_SEVERITY="MAJOR";ERR_CODE="0019";ERR_DYNAMIC="SIN header verification failed";
Basically, it refuses to flash and is stuck at:
26/032/2012 00:32:58 - INFO - Opening device for R/W
26/032/2012 00:32:58 - INFO - Reading device information
EDIT I GOT IT TO WORK
ME 1, SONY 0 (To the 3 guys who followed, you'll know that this is my 2nd phone. Sony replaced my first bricked one)
http://forum.xda-developers.com/showthread.php?t=1766892 <-- FLASH THIS ONE.
Click to expand...
Click to collapse
thanks man.i cant test now but ill do as soon as i can.
matin_08 said:
thanks man.i cant test now but ill do as soon as i can.
Click to expand...
Click to collapse
Ok, I may think I know what's wrong. I'm no expert, but that kernel didn't say it comes with root rights, but some how I got root rights for my phone now.
I think something went wrong when Doomkernel was rooting the phone.
If that version doesn't work, flash a couple of different kernels and see where you go, although I've flashed the following:
In order:
-Doom's
-Advance Stock Kernel
-Doomkernel v1
-The one which I posted.
hey i think i woke it up!i extracted kernel file from stock ics firmware and flashed it with fastboot.but i can see just the sony logo! phone is restarting continuously
matin_08 said:
hey i think i woke it up!i extracted kernel file from stock ics firmware and flashed it with fastboot.but i can see just the sony logo! phone is restarting continuously
Click to expand...
Click to collapse
Use flashtools and flash a firmware,be sure to.shutdown the phone first.
Sent from my LT26i using Tapatalk 2
Related
Plz hep me..i hard bricked my phone while trying to install cwm recovery on my sony xperia u st25i running ics..i read the article i had found again and realised that recovery was for sony xperia p ics..now my phone is not even starting..it has gone plain dead..when i remove the battery and re insert it,led light for charging flashes orange for a moment and the phone goes dead..please,please help me anyone..i cant afford to have this phone as a paperweight..!!
Can you enter fastboot or flash mode?
Sent from my LT26i using xda app-developers app
krabappel2548 said:
Can you enter fastboot or flash mode?
Sent from my LT26i using xda app-developers app
Click to expand...
Click to collapse
No,i cant enter either of them..my phone does not responds to anything..usb cable or charger..vol. up or vol. down or power..wish had never unlocked my bootloader because than i had never developed intrest in all these procedures..i admit,rooting and flashing custom roms,enjoying a vast range f applications for root was fun alltogether but a very costly one..i know i wont be able to get it replaced because i already voided my warranty by unlocking the f***ing bootloader..!!
xperiavish said:
No,i cant enter either of them..my phone does not responds to anything..usb cable or charger..vol. up or vol. down or power..wish had never unlocked my bootloader because than i had never developed intrest in all these procedures..i admit,rooting and flashing custom roms,enjoying a vast range f applications for root was fun alltogether but a very costly one..i know i wont be able to get it replaced because i already voided my warranty by unlocking the f***ing bootloader..!!
Click to expand...
Click to collapse
But your charging light turns orange? That means you should be able to enter fastboot mode. Did you try removing the battery, leave it out of the phone for like a few minutes to be sure.
Then connect USB cable with volume up, without battery in the phone.
Let me know what you get then
Sent from my LT26i using xda app-developers app
Should i be messing with the test pointers to get this undone via hardware..or i should stick to software manipulations using diffrent combos..i hve removed the battery 10 minutes ago,i guess all the capacitor power will be gone by now..so what next should i do..??
xperiavish said:
Should i be messing with the test pointers to get this undone via hardware..or i should stick to software manipulations using diffrent combos..i hve removed the battery 10 minutes ago,i guess all the capacitor power will be gone by now..so what next should i do..??
Click to expand...
Click to collapse
First off calm down and think clearly. I hardbricked my S but revived it. First off the recovery should be related to the kernel. Put your battery in and hold volume up and power for ten seconds. Then let it chill for a few minutes. Then try and enter fastboot so you can flash a new kernel. I have NEVER EVER found a phone that couldnt be revived from brick and I have rooted and modded at least 15 different models and manufacturers. It can be done, you just need patience. Fastboot mode is the way to revive a device and once you get the proper kernel on you should be okay. Just keep trying to enter fastboot. Dont run your battery out all the way though, since sometimes you can get it to low the phone cant charge and the charge mode is related to kernel.
I do have same problem, please help me.
mrsatan said:
First off calm down and think clearly. I hardbricked my S but revived it. First off the recovery should be related to the kernel. Put your battery in and hold volume up and power for ten seconds. Then let it chill for a few minutes. Then try and enter fastboot so you can flash a new kernel. I have NEVER EVER found a phone that couldnt be revived from brick and I have rooted and modded at least 15 different models and manufacturers. It can be done, you just need patience. Fastboot mode is the way to revive a device and once you get the proper kernel on you should be okay. Just keep trying to enter fastboot. Dont run your battery out all the way though, since sometimes you can get it to low the phone cant charge and the charge mode is related to kernel.
Click to expand...
Click to collapse
Hi,
I have installed successfully Dynamic rom on my xperia u, It worked like charm initiailly, but after few hours when I restarted the device its not booting, Just stuck with sony logo, not proceeding further . Fortunately :victory: it enters fastboot mode and even flashmode, kindly help me how can I recover my phone ?
aktherraza said:
Hi,
I have installed successfully Dynamic rom on my xperia u, It worked like charm initiailly, but after few hours when I restarted the device its not booting, Just stuck with sony logo, not proceeding further . Fortunately :victory: it enters fastboot mode and even flashmode, kindly help me how can I recover my phone ?
Click to expand...
Click to collapse
Download and flash a stock firmware using flashtool and be careful about what Rom you flash on your phone always.
Tapatalked !
Rapier07 said:
Download and flash a stock firmware using flashtool and be careful about what Rom you flash on your phone always.
Tapatalked !
Click to expand...
Click to collapse
Hi,
I'll be thankful to you If you can point to a guide to use flash tool to achieve this.
Download official ics ftf from development section of ur xperia
Download flashtool
Install flashtool
Go to c/flashtool/drivers
Install drivers for ur xperia
Now switch of ur phone keep it aside
Go to flashtool
Click thunder icon
Select flashmode
Select ftf
Check no final verification
Check exclude ta
Click flash\start
Now it will ask u to connect ur phone in flashmode
Press the volume down button, keep it pressed and connect to usb
Flashing will start
Let it complete
U r done wait for flashing
By Dr.sanket
Sent from my ST25i using Tapatalk 2
Hurray
Rajul said:
Download official ics ftf from development section of ur xperia
Download flashtool
Install flashtool
Go to c/flashtool/drivers
Install drivers for ur xperia
Now switch of ur phone keep it aside
Go to flashtool
Click thunder icon
Select flashmode
Select ftf
Check no final verification
Check exclude ta
Click flash\start
Now it will ask u to connect ur phone in flashmode
Press the volume down button, keep it pressed and connect to usb
Flashing will start
Let it complete
U r done wait for flashing
By Dr.sanket
Sent from my ST25i using Tapatalk 2
Click to expand...
Click to collapse
Thanks all of you for the help, My phone's soul restored ! :victory:
help help
mrsatan said:
First off calm down and think clearly. I hardbricked my S but revived it. First off the recovery should be related to the kernel. Put your battery in and hold volume up and power for ten seconds. Then let it chill for a few minutes. Then try and enter fastboot so you can flash a new kernel. I have NEVER EVER found a phone that couldnt be revived from brick and I have rooted and modded at least 15 different models and manufacturers. It can be done, you just need patience. Fastboot mode is the way to revive a device and once you get the proper kernel on you should be okay. Just keep trying to enter fastboot. Dont run your battery out all the way though, since sometimes you can get it to low the phone cant charge and the charge mode is related to kernel.
Click to expand...
Click to collapse
i need help just hard brick my xperia s .... no led no fastboot no flashboot....no logo.... nothing at all and i was with 80% battery please mailme at this direction [email protected] i trully need help i dont know what to do anymore
Post your own thread instead of necroing an old one will help. Also saying what happened before the phone died will also help.
Anyway, hold vol up + power for 20 seconds and see if you can get it to vibrate.
If so, after the 3rd vibrate, quickly hold vol down, then jam the USB cable in.
You are now in flashboot. Flash a stock ftf and you should be fine.
links plz
Rajul said:
Download official ics ftf from development section of ur xperia
Download flashtool
Install flashtool
Go to c/flashtool/drivers
Install drivers for ur xperia
Now switch of ur phone keep it aside
Go to flashtool
Click thunder icon
Select flashmode
Select ftf
Check no final verification
Check exclude ta
Click flash\start
Now it will ask u to connect ur phone in flashmode
Press the volume down button, keep it pressed and connect to usb
Flashing will start
Let it complete
U r done wait for flashing
By Dr.sanket
Sent from my ST25i using Tapatalk 2
Click to expand...
Click to collapse
plz can i get a link for ftf file for my xperia u.....thnx
Rajul said:
Download official ics ftf from development section of ur xperia
Download flashtool
Install flashtool
Go to c/flashtool/drivers
Install drivers for ur xperia
Now switch of ur phone keep it aside
Go to flashtool
Click thunder icon
Select flashmode
Select ftf
Check no final verification
Check exclude ta
Click flash\start
Now it will ask u to connect ur phone in flashmode
Press the volume down button, keep it pressed and connect to usb
Flashing will start
Let it complete
U r done wait for flashing
By Dr.sanket
Sent from my ST25i using Tapatalk 2
Click to expand...
Click to collapse
Saved my life!
Was stuck into SONY logo after "testing" each CWM function (like the wipe system, etc .. !)
Many thanks!
Xperia U bricked, tried many things but now it gets stuck at "SONY" logo
I am now downloading this http://forum.xda-developers.com/showthread.php?t=1974430 stock ROM. can you suggest which kernel I will have to use to flash the boot partition with. and any steps I have to follow before flashing the stock ROM using flashtool ?
Background:-
I rooted my phone then unlocked the bootloader the official way.
Installed CM9. worked fine
Then I wanted to back to stock ROM (for some xyz reason)
I got a vodafone image and recovered the phone by flashing it but touchscreen was not working.
I think I have messed up a lot and now I cant get the CM9 working also (touchscreen doesnt work)
Touchscreen not working, is it a software or hardware related ?
I still believe if its software related it can be fixed somehow.
Thanks.
Rajul said:
Download official ics ftf from development section of ur xperia
Download flashtool
Install flashtool
Go to c/flashtool/drivers
Install drivers for ur xperia
Now switch of ur phone keep it aside
Go to flashtool
Click thunder icon
Select flashmode
Select ftf
Check no final verification
Check exclude ta
Click flash\start
Now it will ask u to connect ur phone in flashmode
Press the volume down button, keep it pressed and connect to usb
Flashing will start
Let it complete
U r done wait for flashing
By Dr.sanket
Sent from my ST25i using Tapatalk 2
Click to expand...
Click to collapse
the ftf file includes the kernel, just flash.
Sent from my Xperia Arc S using xda premium
Thanks. But do you think the touchscreen issue is just due to wrong ROM or could it be hawdware ?
tangosierra_ said:
the ftf file includes the kernel, just flash.
Sent from my Xperia Arc S using xda premium
Click to expand...
Click to collapse
It should be ROM issue, I remember seeing this problem in the arc forums too
Sent from my Xperia Arc S using xda premium
Cool. I'll try to flash the ROM. Is there a need to clear the cache and system portions ?
Sent from my Nexus 7 using xda app-developers app
Recently i unlocked the bootloader.
Then i tried to relock the bootloader by flashing 70kb file.
Then i had to repair my phone using SUS but the problem is ,
the phone is not entering flashboot mode.Just RED LED when i connect.
not even vibrating on pressing VolUP+VolDown+power.It just blinks three times in doing so.
Please HELP!!
jptman said:
Recently i unlocked the bootloader.
Then i tried to relock the bootloader by flashing 70kb file.
Then i had to repair my phone using SUS but the problem is ,
the phone is not entering flashboot mode.Just RED LED when i connect.
not even vibrating on pressing VolUP+VolDown+power.It just blinks three times in doing so.
Please HELP!!
Click to expand...
Click to collapse
Is the phone in working condition or its bricked???
Charge it fully!!!
Press volume + and power key until the phone vibrates 3 times and shuts down automatically then try and connect it in flash mode
Sent From Xperia Sola White (MT27i)
Rooted Stock ICS
Hit Thanks If I Helped!!
Thread moved to Q & A section, post in the relevant section next time.
Ok sorry for that but the phone is fully bricked no vibrations upon pressing the power key combinations and the oddest thing is that it goes to flash mode after few minutes and again back to red led when connected to pc
Sent from my MT15i using xda app-developers app
xperia sola bricked
jptman said:
Ok sorry for that but the phone is fully bricked no vibrations upon pressing the power key combinations and the oddest thing is that it goes to flash mode after few minutes and again back to red led when connected to pc
Sent from my MT15i using xda app-developers app
Click to expand...
Click to collapse
i am having the same problem my phone has an orange led while on usb connection,the power combinations do not work and the worst part is that it turns green after some time on usb connection and again goes back to black so i cannot simply install ics on it and the only option to use my phone is to install ics on the device because it's rooted
feel ya
my phone acted the exact same way, after i tampered with my rom, but hoping that its this simple for you too would be naive, but one can Always Hope my usb-cable was a bit Bent, so i pushed the usb-pins in the phones connector a bit towards the middle of the connector and it connected again the red led can simply mean discharged battery, but it can also mean full hard brick :-/ and yeah right, u can try to repair with pcc Good luck
still cant use it
thenut94 said:
my phone acted the exact same way, after i tampered with my rom, but hoping that its this simple for you too would be naive, but one can Always Hope my usb-cable was a bit Bent, so i pushed the usb-pins in the phones connector a bit towards the middle of the connector and it connected again the red led can simply mean discharged battery, but it can also mean full hard brick :-/ and yeah right, u can try to repair with pcc Good luck
Click to expand...
Click to collapse
but man my phone does not show green led which is necessary for repairing using pcc help me bro
jptman said:
Ok sorry for that but the phone is fully bricked no vibrations upon pressing the power key combinations and the oddest thing is that it goes to flash mode after few minutes and again back to red led when connected to pc
Sent from my MT15i using xda app-developers app
Click to expand...
Click to collapse
Now there is a trick to revive it..
Tested by me!!!
Dont skip this step:-
"Charge battery full and shut device down by pressing volume + and power key untill phone vibrates 3 times"
(despite your device bricked cause when u charge or hit power button there is a supply and your device hasn't shut completely)
"Don't connect the phone to desktop until the point no 3-4 below"
1)Open flashtool
2)select the files for flashing
3)when the Popup hits your screen to connect your device in flash mode wait for it to repeat 2-3 times and then connect it asap
4) you will see the device detected and flashing starts the green led goes red for flashing mode
The timing should be spot on!!! If you can't get in one go try a couple of times...
I got my friends Sola working like this!!!
Sent From Xperia Sola White (MT27i)
Rooted Stock ICS
Hit Thanks If I Helped!!
Have you solved? i also have the same problem. When connect usb cable light on red led and phone is not recognized from pc and flashtool
xyt150 said:
but man my phone does not show green led which is necessary for repairing using pcc help me bro
Click to expand...
Click to collapse
soulhackereborn said:
Now there is a trick to revive it..
Tested by me!!!
Dont skip this step:-
"Charge battery full and shut device down by pressing volume + and power key untill phone vibrates 3 times"
(despite your device bricked cause when u charge or hit power button there is a supply and your device hasn't shut completely)
"Don't connect the phone to desktop until the point no 3-4 below"
1)Open flashtool
2)select the files for flashing
3)when the Popup hits your screen to connect your device in flash mode wait for it to repeat 2-3 times and then connect it asap
4) you will see the device detected and flashing starts the green led goes red for flashing mode
The timing should be spot on!!! If you can't get in one go try a couple of times...
I got my friends Sola working like this!!!
Sent From Xperia Sola White (MT27i)
Rooted Stock ICS
Hit Thanks If I Helped!!
Click to expand...
Click to collapse
Tried it many times but it didnt work.
Phone still remains in flash mode.
and i have same problem..
what do i ?
sorry for my bad english
Download official ftf for ur device
Simply flash via flashtool
Hold the power button down + volume up key at the same time until it vibrates once and then three more times, total 4 time vibrates. Now your phone is completely switched off. Now hold the volume key down while plugging in the usb. (first connect it with pc then phone).
This will make your phone to go into fastboot mode. Then using flashtool you can flash new kernel or rom for your phone. Hope it helps
Don't forget to hit thanks button if i helped you.
Sent from my LT22i using xda premium
Gaurav8180 said:
Hold the power button down + volume up key at the same time until it vibrates once and then three more times, total 4 time vibrates. Now your phone is completely switched off. Now hold the volume key down while plugging in the usb. (first connect it with pc then phone).
This will make your phone to go into fastboot mode. Then using flashtool you can flash new kernel or rom for your phone. Hope it helps
Don't forget to hit thanks button if i helped you.
Sent from my LT22i using xda premium
Click to expand...
Click to collapse
NOT WARK
My phone has the same problem .... when i power on the phone LOGO it appear for one or two second then t exclamation sign appears on the screen
plz help me
It is a possibility you bricked your device...
Sent from my Xperia P
R: Xperia sola not entering flashboot(or any other mode) mode! just RED LED!!
Gaurav8180 said:
Hold the power button down + volume up key at the same time until it vibrates once and then three more times, total 4 time vibrates. Now your phone is completely switched off. Now hold the volume key down while plugging in the usb. (first connect it with pc then phone).
This will make your phone to go into fastboot mode. Then using flashtool you can flash new kernel or rom for your phone. Hope it helps
Don't forget to hit thanks button if i helped you.
Sent from my LT22i using xda premium
Click to expand...
Click to collapse
I think you have to Press up volume button to go into fastboot mode, not the down one
Sent from my Xperia Sola using xda app-developers app
some days ago i have unlkocked the bootloader and installed speedy sola kernel. the phone works(experience 2.1 rom), but i can't enter in flashmode.
i have tried to off phone with power button+ volume+ and it turn off(3 vibration), but flashtool don't reveal it.
help pls :crying:
Th4N4Th0S said:
some days ago i have unlkocked the bootloader and installed speedy sola kernel. the phone works(experience 2.1 rom), but i can't enter in flashmode.
i have tried to off phone with power button+ volume+ and it turn off(3 vibration), but flashtool don't reveal it.
help pls :crying:
Click to expand...
Click to collapse
1. Connect your phone to your computer with USB, (press volume down button before it)
(until you see your phone's LED turn to green
2. Open flashtool
3. Click flashmode
4. select kernel to flash. (.54 Sola original kernel (just google it)).
5. You're ready! Try to boot, if it success. Turn off your phone again. And flash your kernel with CWM included.
masprob said:
1. Connect your phone to your computer with USB, (press volume down button before it)
(until you see your phone's LED turn to green
2. Open flashtool
3. Click flashmode
4. select kernel to flash. (.54 Sola original kernel (just google it)).
5. You're ready! Try to boot, if it success. Turn off your phone again. And flash your kernel with CWM included.
Click to expand...
Click to collapse
the led is green but flashtools don'ìt recognize it.
here is the log:
11/022/2013 07:22:14 - INFO - <- This level is successfully initialized
11/022/2013 07:22:15 - INFO - Flashtool Version 0.9.11.0 built on 2013-06-04 22:50:00
11/022/2013 07:22:20 - INFO - Device connected with USB debugging on
11/022/2013 07:22:20 - ERROR - Cannot identify your device.
11/022/2013 07:22:20 - INFO - Selecting from user input
11/022/2013 07:22:28 - INFO - Selected MT27i / 6.1.1.B.1.54 / Global
11/022/2013 07:22:28 - INFO - Preparing files for flashing
11/022/2013 07:22:31 - INFO - Please connect your device into flashmode.
11/022/2013 07:22:33 - INFO - Start Flashing
11/022/2013 07:22:33 - INFO - Processing loader
11/022/2013 07:22:33 - INFO - Checking header
11/022/2013 07:22:33 - INFO - Ending flash session
=====================================================================
the lines in blu appear before i connected the device, is a proble of flashtools or the device?
ps. i fastboot the device and it works( i have installed a kernel and no errors).
PPS. problem solved after unistalling "bluestacks". now try to flash firmware
Hi I'm BrianXYap New to XDA. So I recently just rooted my Sk17i but didn't unlock boot loader. I was trying to install cm10 on my Sk17i.It obviously failed so I gave up. (Using CWM) when I clicked reboot system, I was stuck at the Sony Ericsson logo . I tried to Go to the recovery mode or any other modes but they don't work. Can You DEV's Help me? also when I plug it in to my computer it doesn't charge for some reason. there is also no LED notification light, is it because of the failed Flash caused all these things to happen? Help!
Flash stock ftf Rom via flashtool.
And cm10 needs unlocked boot loader to flash it's custom kernel.
an0nym0us_ said:
Flash stock ftf Rom via flashtool.
And cm10 needs unlocked boot loader to flash it's custom kernel.
Click to expand...
Click to collapse
heres links - http://forum.xda-developers.com/showthread.php?t=1568792
Flashtool method
Download the correct firmware file for your phone at the bottom of the post.
Make sure Flashtool is installed.
Place downloaded firmware file(.ftf format) in Flashtool\firmwares(by default C:\Program Files\Flashtool) folder.
Start Flashtool.
Click the lightning button and choose Flashmode.
Firmware should appear there, if you have it in correct folder. Choose it.
Turn off your phone, connect USB cable to computer, then press Volume Down button and connect USB cable to your phone.
Flashtool should detect your phone and starts flashing. Follow the instructions.
When it says „Flashing completed“, unplug your phone and turn it on.
Click to expand...
Click to collapse
THe Problem is I can't do volume down combination. It still stucks at the logo
Uninstall everything on the PC related to your Phone then start from scratch.
Sent from Myushi
BrianXYap said:
THe Problem is I can't do volume down combination. It still stucks at the logo
Click to expand...
Click to collapse
What volume combination and stuck at the logo mean? You do flashing firmware via flashtool with device off.
It said connect USB cable and then power + vol - .I did it but nothing happened. It's still at the logo. I installed an official firmware once and a blue led indicator showed up. Now it doesn't .
Be sure that the phone is off then plug the usb cabl and hold volum down key in the same time and your in flash mod then open flashtool and see videos on youtube on how to flash ftf files using flashtool and that should be over
Sent from my SK17i using xda app-developers app
BrianXYap said:
It said connect USB cable and then power + vol - .I did it but nothing happened. It's still at the logo. I installed an official firmware once and a blue led indicator showed up. Now it doesn't .
Click to expand...
Click to collapse
do you really want a cm10 rom? then unlock your bootloader (but be mindful that you may lose your warrant and bad things might happen to your phone) here's the tut http://forum.xda-developers.com/showthread.php?t=1879750
after you unlock your bootloader
flash your kernel through flashtool
then install cm10 rom
but if you want to go back to your stock rom
you need flashtool and obviously your stock rom (ftf file)
click the lightning-like button then choose flashmode
select the rom then you'll be prompted to connect your phone
hold the power button and volume down button at the same time until the led light is blue.
wait to complete and your back to your original rom
i hope it helped you
Hi,
i was trying to root my Phone, got into fastboot, and now it stuck´s in a bootloop, blue light, i tried flashtool, but it doesnt recognize my phone - can you help me please?
Thanks.
Moving to right section. Please use search function before open a new thread, and try to post in an existing thread. Disperse information helps to nobody. Regards,
Repair via pcc
Sent from my LT22i using xda app-developers app
user1234x said:
Hi,
i was trying to root my Phone, got into fastboot, and now it stuck´s in a bootloop, blue light, i tried flashtool, but it doesnt recognize my phone - can you help me please?
Thanks.
Click to expand...
Click to collapse
Go to Computer>Local Disk>Flashtool>Drivers ... and run the program then select the Xperia p driver,fastboot drivers and flashmode drivers...
after that download that ftf file http://forum.xda-developers.com/showthread.php?t=2344987 putting in the Computer>Local Disk>Flashtool>Firmwares directory and then start flashtool ... select the bolt button and after that youre going to see 6.2.A.1.100 Central Europe or something like that .. hit flash to the bottom of tha page ... then wait to load flashing files
when a window come up and tell you to connect your phone press the down volume and hold it then connect usb ..
PM me if it worked , I had the same problem !
user1234x said:
Hi,
i was trying to root my Phone, got into fastboot, and now it stuck´s in a bootloop, blue light, i tried flashtool, but it doesnt recognize my phone - can you help me please?
Thanks.
Click to expand...
Click to collapse
Is the blue led still on, or is it just stuck in boot loop, or both?
Try to turn it off, long press power | volume up button untill you feel 3 consecutive vibrations.
user1234x said:
Hi,
i was trying to root my Phone, got into fastboot, and now it stuck´s in a bootloop, blue light, i tried flashtool, but it doesnt recognize my phone - can you help me please?
Thanks.
Click to expand...
Click to collapse
You have to install the drivers first in order to get your phone recognized. Try pressing Vol Up + Power to shut down the phone. Hold it for 10 seconds and then enter fastboot mode and flash using flashtool.
deleted.
please help!
i was flashing the official pacman rom for xperia u. then i connected my phone to the computer to fastboot the cm kernel.
but the flashtool says that drivers need to be installed. i have installed the drivers but the problem still persists.
i tried to goto the cwm but after i keep pressing the vol down button, the led flashes but nothing comes. its a black screen.
now i'm not able to do anything to the phone not even abble to flash stock ftf!
Please help!
vinayakagarwal1996 said:
please help!
i was flashing the official pacman rom for xperia u. then i connected my phone to the computer to fastboot the cm kernel.
but the flashtool says that drivers need to be installed. i have installed the drivers but the problem still persists.
i tried to goto the cwm but after i keep pressing the vol down button, the led flashes but nothing comes. its a black screen.
now i'm not able to do anything to the phone not even abble to flash stock ftf!
Please help!
Click to expand...
Click to collapse
Press volume up | power key untill you feel 3 vibrations then try to power up again.
EDIT: have you installed flash mode and fastboot drivers mode drivers too?
ChikeD said:
Press volume up | power key untill you feel 3 vibrations then try to power up again.
EDIT: have you installed flash mode and fastboot drivers mode drivers too?
Click to expand...
Click to collapse
Or remove the battery you may need to open pc device manager and manualy uninstall the drivers and make sure u manualy install the right ones
Sent from my Xperia U using xda app-developers app
ChikeD said:
Press volume up | power key untill you feel 3 vibrations then try to power up again.
EDIT: have you installed flash mode and fastboot drivers mode drivers too?
Click to expand...
Click to collapse
i tried but felt only 1 vibration which powered up the device and got stuck on kernel.
vinayakagarwal1996 said:
i tried but felt only 1 vibration which powered up the device and got stuck on kernel.
Click to expand...
Click to collapse
Wait untill you feel 3 vibrations.
What firmware you had when you installed the rom and can you give the link to the thread of the rom you installed?
Do you have ftf to original formware?
One vibration reboot, three power off.
After you will switch off, try flash tft then.
Sent from my Xperia Sola using xda app-developers app
ChikeD said:
Wait untill you feel 3 vibrations.
What firmware you had when you installed the rom and can you give the link to the thread of the rom you installed?
Do you have ftf to original formware?
Click to expand...
Click to collapse
Actually before that i was trying to port a rom but it didnt work out.
so i flashed the pacman rom http://forum.xda-developers.com/showthread.php?t=2372433
in this i had to fastboot the boot.img which i then was unable to.
and before that i had the same rom installed. i have the original ftf.
i instaled the latest flashtool. it says the drivers arent installed but they are.
windows says unable to install drivers.
after i press the vol up and power, after 1 vibration it goes to kernel. i waited for 5 min pressing the buttons but nothing happened.
when on kernel, flashtool says device connected in usb debugging off.
Thanks for your help!
in the flashtool, i chose the log level to debug.
then my phone was able to get to the fastbot mode and i successfully fastbooted the correct cm kernel and booted up the rom!
vinayakagarwal1996 said:
Actually before that i was trying to port a rom but it didnt work out.
so i flashed the pacman rom http://forum.xda-developers.com/showthread.php?t=2372433
in this i had to fastboot the boot.img which i then was unable to.
and before that i had the same rom installed. i have the original ftf.
i instaled the latest flashtool. it says the drivers arent installed but they are.
windows says unable to install drivers.
after i press the vol up and power, after 1 vibration it goes to kernel. i waited for 5 min pressing the buttons but nothing happened.
when on kernel, flashtool says device connected in usb debugging off.
Click to expand...
Click to collapse
Did you replace the kernel image before installing? Realy weird why the didn't fo it themselves.
No ppoint to try booting the phone.
You have removable battery so try to remove it for a minute, put it back and see if you can connect in flash mode and flash original formware.
BTW what do you mean by "goes to kernel?" recovery?
ChikeD said:
Did you replace the kernel image before installing? Realy weird why the didn't fo it themselves.
No ppoint to try booting the phone.
You have removable battery so try to remove it for a minute, put it back and see if you can connect in flash mode and flash original formware.
BTW what do you mean by "goes to kernel?" recovery?
Click to expand...
Click to collapse
sorry. i may be wrong. i meant the first image that comes when you boot like fxp logo/sony/samusung logo
btw i have fixed the problem as stated in my above post.
and i have now reflashed it.