I think that my phone is bricked it is not turning on in any way no recovery no download mode, but when i connet it to pc it shows on odin itry to flash a rom it says setup connection. then one minute and the connection is lost until i disconnect an d reconnect it again please help
naelmnael said:
I think that my phone is bricked it is not turning on in any way no recovery no download mode, but when i connet it to pc it shows on odin itry to flash a rom it says setup connection. then one minute and the connection is lost until i disconnect an d reconnect it again please help
Click to expand...
Click to collapse
r u running ICS 4.0.4? try to charge your battery then try to remove your battery 10-20mins, or try to use other cable..
Related
REPAIR YOUR X 10I
FILES YOU NEED::http://www.mediafire.com/download/tdg4dho2bwq6fg5/X10i_3.0.1.G.0.75_only%20kernel_baseband.ftf
http://www.mediafire.com/download/vy4v24ditk4lsxa/Xperia_X10i_3.0.1.G.0.75_GLOBAL-GGL_GENERIC_1232-9897.rar
http://www.mediafire.com/download/0pgnz7iy2yq4iae/FlashTool_0.2.9.1-GBready_root_xRec.exe
INSTRUCTIONS IS HERE
http://forum.xda-developers.com/showthread.php?t=2570671
PLEASE BEFORE YOU START PUT YOUR PHONE ON CHARGER 3-4 HOURS
PRESS THANX IF HELPED
I tried using your solution but every time I failed to connect my X10 to flash mode. Unplug the USB, take out put back the battery of my phone, press the back button on the phone and plug in USB but nothing comes out and just showing 19/025/2013 04:25:24 - INFO - Searching Xperia....
19/025/2013 04:25:24 - ERROR - Please plug you device in flash mode many many times. My phone battery was fully charge with 5 hours. Any solutions with this?
answer
try this: plug your cable in computer but dont conect your phone,then open flash tools,run flash and chose x 10 i baseband and kernel only ftf,then flash tools will ask you for conect your phone in flash mode.then pull batery of your phone and wait 1 minute,pull batery in,hold back button and conect usb in phone.the phone should be in the flash mode and start flashing.I repared 2 xperia x 10 that were compleatly dead,seus,pc companion and flash tools dont recognize it and only blinking red,no boot up,no bootloop, no power on, nothing helped
noob hacker said:
try this: plug your cable in computer but dont conect your phone,then open flash tools,run flash and chose x 10 i baseband and kernel only ftf,then flash tools will ask you for conect your phone in flash mode.then pull batery of your phone and wait 1 minute,pull batery in,hold back button and conect usb in phone.the phone should be in the flash mode and start flashing.I repared 2 xperia x 10 that were compleatly dead,seus,pc companion and flash tools dont recognize it and only blinking red,no boot up,no bootloop, no power on, nothing helped
Click to expand...
Click to collapse
I tried this before but still can't connect my phone to flash mode.
Hikigaya Hachiman said:
I tried this before but still can't connect my phone to flash mode.
Click to expand...
Click to collapse
send me a phone,I will fix it and sent you back.....write me message pm
noob hacker said:
send me a phone,I will fix it and sent you back.....write me message pm
Click to expand...
Click to collapse
I think i can't send you because im at Malaysia and thats not my phone.
some questions
Hikigaya Hachiman said:
I think i can't send you because im at Malaysia and thats not my phone.
Click to expand...
Click to collapse
Hi,
I have some confirmation questions:
Which ROM ftf do you have, which was the original baseband on the phone? Maybe check in STOCK ROM list for a better suited ROM.
I have better experiences when connecting the other way round: plug the cable into the phone and connect either at the computer or into a short usb-extender cable in convenient reach.
When doing it the other way round, I have often 'timing problems' to fiddle the usb micro into the socket at the phone.
Maybe try another cable and/or carefully press the plug to the phones frontside to prevent connection problems.
Alexej
Hello
I have an Lenovo s898t+ from aliexpress. with androdi 4.4.2 And I was trying to increase my file system root partition in phone. I use apk meteos MTK 6592, and after getting to recovery mode I did everithing like was write in other forumm that I found set factory restart. And now my phone is in something lie bootloop always showing android figure and when I try to turn it off only show
forrmating /data...
mount system/ error
and can`t get to recovery mode or if I try to connect to PC via USB without the batery inside the phone is still rebooting. I know how to flash stock rom, but cant do that becouse the phone is still connecting and disconnecting to PC.
Can somebody help please I have been searching for 4 days with no luck.
Thanks for all you answers
If your phone is a MTK device..
U can flash a new rom..
With SPflash tools..
abhinavp649 said:
If your phone is a MTK device..
U can flash a new rom..
With SPflash tools..
Click to expand...
Click to collapse
Cant get phone to stable connection to PC always reseting without battery and with baterry the bootloop shows up and did not connect to pc
u have to start the download process from SPtools before connecting your phone to PC
hopefully, it will show your phone..
some phones have a trigger to start the download..may be power button or any of volume buttons..
Some phone also required to pop in the battery to start the process..
Try any of these options..
hopefully, u will have ur phone flased with a new rom..
ingshibbby said:
Cant get phone to stable connection to PC always reseting without battery and with baterry the bootloop shows up and did not connect to pc
Click to expand...
Click to collapse
u have to start the download process from SPtools before connecting your phone to PC
hopefully, it will show your phone..
some phones have a trigger to start the download..may be power button or any of volume buttons..
Some phone also required to pop in the battery to start the process..
Try any of these options..
hopefully, u will have ur phone flased with a new rom..
USB on my I9300 keeps disconnecting, i tried Factory reset, wipe all ,fix permissions, odin mode, clean port with needle, but no luck
Phone is charging but usb keeps disconnecting and connecting , it stays connected not even for 1 sec.
Please help me.
Cybrion said:
USB on my I9300 keeps disconnecting, i tried Factory reset, wipe all ,fix permissions, odin mode, clean port with needle, but no luck
Phone is charging but usb keeps disconnecting and connecting , it stays connected not even for 1 sec.
Please help me.
Click to expand...
Click to collapse
Sounds like you need a new usb port to me :crying: If you want to transfer files while you get it fixed you can use one of the many wifi enabled apps to transfer files from your phone to the pc. Also if you want to use Odin there is a mobile version here >> https://play.google.com/store/apps/details?id=eu.chainfire.mobileodin.pro << no pc needed (although root is required). Best way to test it is flash another rom if problem is still there then it is hardware problem.
I wanted to do this, but i don't have WIFI , and i couldn't flash even 1mb because of this disconnecting
Cybrion said:
I wanted to do this, but i don't have WIFI , and i couldn't flash even 1mb because of this disconnecting
Click to expand...
Click to collapse
Mobile Odin doesn't need a usb like I said no pc needed you flash from the phone but of course you need root.
tallman43 said:
Mobile Odin doesn't need a usb like I said no pc needed you flash from the phone but of course you need root.
Click to expand...
Click to collapse
ok i'll try
I THINK I CAN FIX MY PHONE BECAUSE I ONLY HAVE A BOOT LOOP BY CHANGING BUILD.PROP MY PHONE IS ROOTED BUT I DON'T HAVE CLOCK WORK MOD INSTALLED ON MY PHONE SO I TRY TO WIPE FACTORY RESET USING STOCK RECOVERY BUT ITS NOT WORKING SO I TRY TO DOWNLOAD THE FIRMWARE OF MY PHONE SO THE BUILD.PROP WILL RESET TO NORMAL ONE NOW WHEN I'M USING THE SP TOOL I GOT A BIG PROBLEM I PLUG MY PHONE TO MY PC WITH OUT BATTERY AND NOT HOLDING VOLUME UP BUTTON AND IT CONNECT AND DISCONNECTS ALL THE TIME AND WHEN I UNPLUG IT AND TRY TO CLICK DOWNLOAD ON SP TOOL AND THEN PLUG MY PHONE THE SP TOOL DETECT MY PHONE THE RED LINE APPEAR AND BUT THE THING IS IT ALWAYS CONNECT AND DISCONNECTS I DON'T KNOW HOW TO FIX IT I TRY TO PUT IT ON THE OTHER USB SLOTS ON MY PC BUT STILL THE SAME I CHANGE MY USB CABLE BUT THE SAME AGAIN ANY IDEA HOW TO FIX THIS PROBLEM? I REALLY NEED YOUR ANSWER I NEED FAST ANSWER BECAUSE MY MOM WILL HATE ME IF SHE KNOWS THAT MY PHONE BRICKED!:crying:
Deadly123 said:
I THINK I CAN FIX MY PHONE BECAUSE I ONLY HAVE A BOOT LOOP BY CHANGING BUILD.PROP MY PHONE IS ROOTED BUT I DON'T HAVE CLOCK WORK MOD INSTALLED ON MY PHONE SO I TRY TO WIPE FACTORY RESET USING STOCK RECOVERY BUT ITS NOT WORKING SO I TRY TO DOWNLOAD THE FIRMWARE OF MY PHONE SO THE BUILD.PROP WILL RESET TO NORMAL ONE NOW WHEN I'M USING THE SP TOOL I GOT A BIG PROBLEM I PLUG MY PHONE TO MY PC WITH OUT BATTERY AND NOT HOLDING VOLUME UP BUTTON AND IT CONNECT AND DISCONNECTS ALL THE TIME AND WHEN I UNPLUG IT AND TRY TO CLICK DOWNLOAD ON SP TOOL AND THEN PLUG MY PHONE THE SP TOOL DETECT MY PHONE THE RED LINE APPEAR AND BUT THE THING IS IT ALWAYS CONNECT AND DISCONNECTS I DON'T KNOW HOW TO FIX IT I TRY TO PUT IT ON THE OTHER USB SLOTS ON MY PC BUT STILL THE SAME I CHANGE MY USB CABLE BUT THE SAME AGAIN ANY IDEA HOW TO FIX THIS PROBLEM? I REALLY NEED YOUR ANSWER I NEED FAST ANSWER BECAUSE MY MOM WILL HATE ME IF SHE KNOWS THAT MY PHONE BRICKED!:crying:
Click to expand...
Click to collapse
OK, first:
Please do not type in caps lock. This post is extremely difficult to read.
Second:
Never alter build prop without a custom recovery and a backup of stock.
Third:
You will most likely need to flash your factory ROM to fix this.
Hello guys, I have a quiet severe issue with my beloved S9+. It first came up when I tried to move files from my PC to my phone. I just keeps disconnecting and then reconnecting in an interval of maybe 30 secs or something. Back then it wasn't that big of a problem, as I just downloaded the necessary files (ROMs in that case) on the phone itself. But as I am now trying to factory reset my phone it's a huge problem, because it just disconnects and reconnects while flashing in odin at about 10-30 secs*(depending on the dc interval). When rebooting afterwards an exclamation mark (flashing went wrong) comes up and tells me to use the Samsung PC software to reset it, but that won't recognize my device and I don't have any reset code or whatsoever. I tried using different computers, reinstalling drivers, rebooting - same problem.
I'd be very grateful for any tip or advice.
Try an other USB Cable. The worst case is, if your USB Port at the phone is damaged
profi_fahrer said:
Try an other USB Cable. The worst case is, if your USB Port at the phone is damaged
Click to expand...
Click to collapse
unfortunately its not about the cable, port, or pc as ive mentioned ... im afraid its something phone hard/software related
Okay so now I've flashed TWRP thru odin which was luckily possible as it didnt take that long. I'm back to RR Rom but I still have the dc/rc problem... Any other way to get back to stock?
If you plug the phone into the normal socket charger, does it also interrupt the charging?
If yes = problem at the Phone
If no = problem at any other source (maybe input current?)
profi_fahrer said:
If you plug the phone into the normal socket charger, does it also interrupt the charging?
If yes = problem at the Phone
If no = problem at any other source (maybe input current?)
Click to expand...
Click to collapse
No... it charges just normal
Try to delete the drivers from your PC. The program and in the Device Manager at Windows. Now restart your PC and boot the phone to the OS. No matter what OS. Do not open Odin yet.
Lock the Phone and plug it into the PC and wait a few minutes. Unplug it from the PC, unlock the Phone and plug it again into the PC. Wait again a few minutes, that the PC can install all drivers. Ignore it, when it disconnects. Again unplug the phone. Then open Odin and plug the Phone again into the PC.
Maybe this should help. Note: Unplug the Phone only at the PC Port, not at the Phone Port
snOwjAwk said:
Hello guys, I have a quiet severe issue with my beloved S9+. It first came up when I tried to move files from my PC to my phone. I just keeps disconnecting and then reconnecting in an interval of maybe 30 secs or something. Back then it wasn't that big of a problem, as I just downloaded the necessary files (ROMs in that case) on the phone itself. But as I am now trying to factory reset my phone it's a huge problem, because it just disconnects and reconnects while flashing in odin at about 10-30 secs*(depending on the dc interval). When rebooting afterwards an exclamation mark (flashing went wrong) comes up and tells me to use the Samsung PC software to reset it, but that won't recognize my device and I don't have any reset code or whatsoever. I tried using different computers, reinstalling drivers, rebooting - same problem.
I'd be very grateful for any tip or advice.
Click to expand...
Click to collapse
Set screen time out to 10 mins & try or Don't let the screen turn off while connected
profi_fahrer said:
Try to delete the drivers from your PC. The program and in the Device Manager at Windows. Now restart your PC and boot the phone to the OS. No matter what OS. Do not open Odin yet.
Lock the Phone and plug it into the PC and wait a few minutes. Unplug it from the PC, unlock the Phone and plug it again into the PC. Wait again a few minutes, that the PC can install all drivers. Ignore it, when it disconnects. Again unplug the phone. Then open Odin and plug the Phone again into the PC.
Maybe this should help. Note: Unplug the Phone only at the PC Port, not at the Phone Port
Click to expand...
Click to collapse
Did not help either unfortunately...
RISHI RAJ said:
Set screen time out to 10 mins & try or Don't let the screen turn off while connected
Click to expand...
Click to collapse
did not have any impact, also in download mode the screen is on the whole time no matter what