Hi guys,
I'm not an Android expert, but AFAIK is a Linux system.
I'm quite familiar with Unix/Linux world and wondering if there's a way to see the messages during boot just like on a console?
I'm asking, beacause my ray hangs at sony-ericsson logo, and can't figure out what's wrong with it.
Thank you!
to solve problem .. flash your stock .ftf again with flashtool
Well u can use adb for that...use adb logcat...search in xda if u don't know how to use adb...it will give u a complete log as u need
Cheers,
AJ
Mohamed Hashem said:
to solve problem .. flash your stock .ftf again with flashtool
Click to expand...
Click to collapse
tried to flash stock gb .42 ftf, but still the same, and cwm is gone now, since custom kernel was overwritten by stock one.
regarding adb, all the adb tutorials mentiones to use usb debug mode, but how can I activate debuge mode, once my phone doesn't boot?
thanks.
nroberto13 said:
tried to flash stock gb .42 ftf, but still the same, and cwm is gone now, since custom kernel was overwritten by stock one.
regarding adb, all the adb tutorials mentiones to use usb debug mode, but how can I activate debuge mode, once my phone doesn't boot?
thanks.
Click to expand...
Click to collapse
i think usb debug will not work anyway if ur phone powered off
try to flash custom kernel again , then u will have CWM , then remove your SD Card and put it in reader , then put any ROM in it , then put it again in ur phone , then flash it with CWM , i made that before with CM ROM & it worked :good:
I tried to flash cutom rom with cwm before flashing stock, but didn't work .
The phone is not powered off when flashing, it's either in fastboot or in flash mode.
nroberto13 said:
I tried to flash cutom rom with cwm before flashing stock, but didn't work .
The phone is not powered off when flashing, it's either in fastboot or in flash mode.
Click to expand...
Click to collapse
Do you know why it's not booting? Did you flash a new rom, did you install a special app, did you do an update over the air (using WiFi)? Or any other idea?
Sent from my SK17i running stock ics (.587)
mihahn said:
Do you know why it's not booting? Did you flash a new rom, did you install a special app, did you do an update over the air (using WiFi)? Or any other idea?
Sent from my SK17i running stock ics (.587)
Click to expand...
Click to collapse
I flashed a custom rom.
Actually, i was on ICS, and wanted to try custom GB illuminative.
Flashed the v10, everything was fine, but Ant+ wasn't working, and dev of the rom was helping me to get ant+ working on the device, so he added things to rom required for ant. I did flash some times the rom without issues, but the last was unlucky .
By that time, my BL was locked, so I had to root my phone to install cwm.
Interestingly the cwm was gone after each rom flash, not sure why, so I had to take the process over and flashed GB .42, rooted with doomlord, script, installed x-parts, then cwm from x-parts, and then flash custom rom from cwm.
basically these were the steps I was doing, and after a cwm flash of the custom rom, the phone ended hanging at sony logo.
I then tried different kind of stock firmwars ( ICS, GB ) to flash with flashtool and SEUS as well, without any luck.
afterwards, I unlocked my BL, flashed cusotm kernel with flashtool ( containing cwm ) , then flash a version of the illuminative custom rom which was working before, but still the sam. somebody then advised to flash again a stock ftf, I did a stock GB .42, but still the same.
now, cwm is gone, as stock kernel overwrote the custom one.
That's the story .
As i remember i can enable usb debug even phone not boot to system. By charging phone with pc(not standard charger) then hold power button and at windows(or else) will ask for driver
Ps. I did that with X8, didn't know with 2011's phone.
Sent from my ST27i using xda app-developers app
Hmm okay you could try to flash the unbricking ftf (you can find it in someguyfromhell's sticked thread) and afterwards stock gingerbread or ics again, but I don't know if that could work or maybe make it even worse (normally it's to unbrick if you did an ota update on unlocked bootloader, but let's see). Maybe it's worth a try
The problem about cwm that's gone: if you are still able to boot into fastboot mode, you can flash another kernel and for example try to install cyanogenmod or any other rom. Just try cm10 or cm10.1. Maybe in the end a rom will boot
Sent from my SK17i running stock ics (.587)
tried, and still the same.
The only reason I can think of is that I may forgot once to enable usb debugging, and used flashtool with usb debugging off. could that lead to this kind of issues?
How could I enable usb debugging, without being able to start the phone OS?
tried eswawan's advise, but didn't work.
PS. when I connect the phone in flash mode, flashtool says phone connected with USB debugging off.
Is you connect phone(off) to pc then it goes to offline charging mode???
Sent from my ST27i using xda app-developers app
nroberto13 said:
tried, and still the same.
The only reason I can think of is that I may forgot once to enable usb debugging, and used flashtool with usb debugging off. could that lead to this kind of issues?
How could I enable usb debugging, without being able to start the phone OS?
tried eswawan's advise, but didn't work.
PS. when I connect the phone in flash mode, flashtool says phone connected with USB debugging off.
Click to expand...
Click to collapse
No, USB debugging off shouldn't lead to such a problem
Try to reinstall all drivers for all devices/modes from flashtool-> drivers. Then you turn the phone off, take off battery, wait 15 seconds, reinsert battery, hold volume up and while holding volume up just connect the phone via usb to your pc. The blue notification led should light up now and then you should be able to flash another kernel. Try it again
Sent from my SK17i running stock ics (.587)
eswawan said:
Is you connect phone(off) to pc then it goes to offline charging mode???
Sent from my ST27i using xda app-developers app
Click to expand...
Click to collapse
yes, it goes to offline charging mode!
mihahn said:
No, USB debugging off shouldn't lead to such a problem
Try to reinstall all drivers for all devices/modes from flashtool-> drivers. Then you turn the phone off, take off battery, wait 15 seconds, reinsert battery, hold volume up and while holding volume up just connect the phone via usb to your pc. The blue notification led should light up now and then you should be able to flash another kernel. Try it again
Sent from my SK17i running stock ics (.587)
Click to expand...
Click to collapse
during my unbrick journey, I did reinstall my windows, and drivers, and didn't help, so I don't think it would make any sense to try once again ...
nroberto13 said:
yes, it goes to offline charging mode!
during my unbrick journey, I did reinstall my windows, and drivers, and didn't help, so I don't think it would make any sense to try once again ...
Click to expand...
Click to collapse
With the procedure I posted above it shouldn't simply boot to offline charging mode, so maybe it is a driver problem. Try it step by step like posted above, maybe it could work. If not it was worth a try
Sent from my SK17i running stock ics (.587)
what does it mean if it goes to offline charging mode, also what does it mean if it doesn't go?
PS. not sure if it's right, but when I connect the phone to pc, connects in flash mode, even if I don't hold vol down, the notification led is solid green, then the led turns off, Sony Ericsson appears, then the battery with the power sign and finally notification led turns orange. when I short press power button now, the battery with power sign shows up on screen.
nroberto13 said:
what does it mean if it goes to offline charging mode, also what does it mean if it doesn't go?
Click to expand...
Click to collapse
Normally while having phone switched off and just holding volume up and connecting to pc the blue led should light up and you are in fastboot mode. If it goes directly into offline charging mode are the wrong drivers installed or you do something wrong or phone is hardbricked...
Sent from my SK17i running stock ics (.587)
Umm...as much as I cud understand....u have used sus before flashtool with unlocked bootloader which MIGHT cause the problem...Try these steps(@mihahn though mentioned earlier) -
1. Uninstall flashtool and delete everything related to it.
2. Now reinstall it to your c: drive.
3. Go to C:/Flashtool/Drivers and install flashtool-drivers.exe with all the drivers.
4. Now download this http://www.multiupload.com/Q103V01CV1 and keep it in C:/Flashtool/firmwares(delete everything present in it already)
5. Now start flashtool.
6. Remove battery from your phone and keep the battery out for 15 sec.
7. Reinsert the battery hold down vol-down button and connect your phone to usb cable connected to pc.
8. Now click on the flash icon and select flashmode and flash the files.
9. Now download this - http://www.mediafire.com/?2j7i7rruqxnui3q
10. Now keep it in firmware folder. REMEMBER to delete any previous files prent in the folder.
11. Now go to flashmode in the same manner and flash it.
12. Now boot your phone, it must start
Cheers,
AJ
mihahn said:
Normally while having phone switched off and just holding volume up and connecting to pc the blue led should light up and you are in fastboot mode. If it goes directly into offline charging mode are the wrong drivers installed or you do something wrong or phone is hardbricked...
Sent from my SK17i running stock ics (.587)
Click to expand...
Click to collapse
Sorry, I think I wasn't clear enough. I thought I should be connecting the phone without holding any of the volume buttons, just to try if it's charging in offline mode. Here's the exact status.
1. If I do not hold any volume buttons, the phone goes into flash mode ( solid green led ), and after a short while ( 20-30 sec ) led turns off, Sony Ericsson logo shows up, then goes away and battery with power sign is displayed when I short press the power button
2. if I hold vol down, phone behaves the same way as at 1.
3. if I hold vol up, phone goes in fastboot mode ( solid blue led ) and stay solid blue, it is not going into charging mode.
Abhinav2 said:
Umm...as much as I cud understand....u have used sus before flashtool with unlocked bootloader which MIGHT cause the problem...Try these steps(@mihahn though mentioned earlier) -
1. Uninstall flashtool and delete everything related to it.
2. Now reinstall it to your c: drive.
3. Go to C:/Flashtool/Drivers and install flashtool-drivers.exe with all the drivers.
4. Now download this http://www.multiupload.com/Q103V01CV1 and keep it in C:/Flashtool/firmwares(delete everything present in it already)
5. Now start flashtool.
6. Remove battery from your phone and keep the battery out for 15 sec.
7. Reinsert the battery hold down vol-down button and connect your phone to usb cable connected to pc.
8. Now click on the flash icon and select flashmode and flash the files.
9. Now download this - http://www.mediafire.com/?2j7i7rruqxnui3q
10. Now keep it in firmware folder. REMEMBER to delete any previous files prent in the folder.
11. Now go to flashmode in the same manner and flash it.
12. Now boot your phone, it must start
Cheers,
AJ
Click to expand...
Click to collapse
I may not be clear enough here either. I didn't use sus after unlocking BL, I know it bricks he phone, anyway, I did flash the unbrick ftf mentioned by mihahn. here are the steps I did so far :
1. I was on ICS ( Iced Bean 3.4 ) , with BL lockedand phone rooted and wanted to try custom GB illuminative.
2. I flashed the rom with cwm, and everything was fine, but Ant+ wasn't working, and dev of the rom was helping me to get ant+ working on the device, so he added things to rom required for ant. I did flash the rom several times, without issues, but the last was unlucky .
3. Interestingly the cwm was gone after each rom flash, not sure why, so I had to take the rooting process over and flashed GB .42, rooted with flashtool, installed x-parts, then cwm from x-parts, and then flash custom rom from cwm.
4. and after a cwm flash of the custom rom, the phone ended hanging at sony ericsson logo.
5. I then tried different kind of stock firmwares ( ICS, GB ) to flash with flashtool and SEUS as well, without any luck.
6. afterwards, I unlocked my BL, flashed cusotm kernel with flashtool ( containing cwm ) , then flashed a version of the above mentioned GB illuminative custom rom which was working before, but still the same.
7. somebody then advised to flash again a stock ftf, I did a stock GB .42, but still the same, now, cwm is gone, as stock kernel overwrote the custom one.
8. tried to flash someguyfromhell's unbrick ftf, which is for the FOTA brick whith BL unlocked, as I understood.
9. reflashed stock GB .42 with flashtool, but phone still hangs at sony Ericsson logo.
In this status, could I connect to the phone using adb, so I could do a adb logcat ?
If so, please advise how.
Thanks.
@nroberto13 Do you mind telling us which ftfs u flashed?
Cheers,
AJ
I don't really know what's happening. I had PexoRom v2.1 and I wanted to make some wipes, change kernel and some other stuff, but my surprise, Fastboot is not working.
When I turn the phone into fastboot mode, (vol+ while connecting USB), the blue led appears, but only for about 6 seconds, then the phone disconnects and shows battery charging thing.
I have tested to reflash stock rom, also to re-lock the kernel and repair using Xperia Companion. I'm using Windows 10 with official Xperia cable. Any idea about why this happend?
I have the same problem. Now I'm tring to find some ROM that I can flash directly from TWRP to avoid fastboot flashing. Did you find any maybe?
Winamp_zg said:
I have the same problem. Now I'm tring to find some ROM that I can flash directly from TWRP to avoid fastboot flashing. Did you find any maybe?
Click to expand...
Click to collapse
Hi IAM using Concept-ify
It's very good ROM
It's more stable than stock ROM and you will have more free space.
Before when I had stock ROM I always had problems with free space I couldn't install apps that I need. Since I flashed Concept-ify this problem is past for me.
iFlashed said:
I don't really know what's happening. I had PexoRom v2.1 and I wanted to make some wipes, change kernel and some other stuff, but my surprise, Fastboot is not working.
When I turn the phone into fastboot mode, (vol+ while connecting USB), the blue led appears, but only for about 6 seconds, then the phone disconnects and shows battery charging thing.
I have tested to reflash stock rom, also to re-lock the kernel and repair using Xperia Companion. I'm using Windows 10 with official Xperia cable. Any idea about why this happend?
Click to expand...
Click to collapse
I have same problem after i patched the "SkyMelon Kernel" my sony won't connect on any pc (usb debug too) now i'm stuck with fastboot for trying to relock >.<