Hello guys, I have (I think) soft bricked my Galaxy S2.
(Details: UK Phone, Carrier was Orange but now I am running 3 on it, official phone model Galaxy I9100T (NFC support iirc) )
Right I am curious bunny hacking away at the phone from the day I bought it, reading pages after pages on different roms and kernel and everything. Finally I settled on CyanogenMod 9 and then went straight to the CM10.1 release. Today Morning I installed the 23/02/2013 CM10.1 realease and then started browsing the XDA forums on whats new. I came across the Siyah 6.0b kernel release and saw it was compatible with cm10.1, eager and foolish I downloaded the apk without doing any further reading or any instruction, overconfident from all the flashing I have been doing for the past year, flashed the kernel via CWM recovery. Now the phone is stuck in what I assume is a boot loop (again I am pretty noobish).
So What have I tried to fix the soft brick?
I tried to go "restore" an img I had taken a week ago of the system with CWM but the phone would no longer boot into recovery.
So I went ahead and got all the recovery package (I9100TDULP9_I9100THUTLP7_HUT) to reflash my phone with Odin 3.07.
This is where I hit a brick wall and now I am truly lost at what to do, my computer doesn't recognise the phone (Download Mode). I keep getting "there is a problem with this device" error and the Device manager shows an unknown device connected. So I installed the Samsung drivers from the samsung website with no luck. Still getting unknown device error. So I googled for a solution and the only solution that came up was reformat my PC since it could be a problem within the OS, so I went forward and used two other PC and still getting the error. Please Help SOS.
tl;dr: Getting Device not recognised error when I connect phone to the computer via USB cable.
Thanks in advance to all the knights to my rescue
DNoob92 said:
I came across the Siyah 6.0b kernel release and saw it was compatible with cm10.1, eager and foolish I downloaded the apk without doing any further reading or any instruction, overconfident from all the flashing I have been doing for the past year, flashed the kernel via CWM recovery. Now the phone is stuck in what I assume is a boot loop (again I am pretty noobish).
So What have I tried to fix the soft brick?
Click to expand...
Click to collapse
Just go to recovery menu (VOLUP+MENU+POWER) and wipe cache and wipe dalvik. That should fix it.
surplus mplieac
crocodilechris said:
Just go to recovery menu (VOLUP+MENU+POWER) and wipe cache and wipe dalvik. That should fix it.
Click to expand...
Click to collapse
I cannot enter Recovery Mode, the screen just goes blank
EDIT: So the only thing that works atm is
1) The battery charge animation (huge green battery in the middle of the screen) when plugged in.
2) Download/Odin mode (which 3 computer refuse to recognise when connected via a USB cable)
EDIT2: The other thing I forgot to mention was, that I have lost the original SII micro USB cable which was black and now I am using the white micro USB cable I received with my Galaxy Note 2.
You could try uninstalling all Samsung-related drivers/software (Ie: Kies), download the Android Naked Driver or the Android ADB Driver (I wish I could recall where I got it from, but it also came with the driver for the Galaxy SII... Sounds like it might be more of a driver issue than it would be a cable issue..
Borrow and S2 cable.
There are a lot of guys having issues with note's cable.
Try a laptop, and install kies on any other pc you try.
Flash siyah v5 instead of flashing v6.
You can relax, if the only thing you did is flash a kernel then there is nothing wrong with your phone.
Try different cables, try Odin 1.85 (that one always worked for me), try different pc's, reinstall drivers, make sure no kies process is running in the background.
First of all thanks for the replies
I couldn't get the drivers working still (after re-installing, installing kies). But while eating lunch I remembered reading about removing battery and pressing the Power button and it doing something I couldn't quite remember. So I thought to myself it wouldn't hurt trying. Did that and the phone Finally booted in recovery mode, I took a breather of relief and than located my previous backup img and restored the phone.
But now a new problem arose, the phone went into SIM lock as soon as it booted and now I guess I have to fix that
Well thanks guys
Quick question guys is SIM network unlock pin basically same unlocking phone form a carrier?
It's asking for a SIM pin or network code?
Get galaxysim unlock by searching xda (free here, paid at play store).
Sent from the little guy
Related
i've read almost every single post related on this subject, tried almost everything but no go.
recently, i installed SS-6 to my girlfriend's Vibrant but she didn't like it, so i attempted to revert to my nandroid from the original stock rom.. nandroid gave an MD5 error and did not installed.
at that point, i had already wiped data/cache, prior to nandroid.
i rebooted the phone, and now im stuck on the Vibrant splash.
i have tried to go to recovery mode via hard buttons but no go. i actually tested with another Vibrant and on that one, im able to get into recovery so it is not that i'm missing pressing a button or what not. been trying anxiously to see if im able to go either to download mode or get into cwm and flash cyanogenmod!
tried to use ODIN/ADB in order to boot into cwm to flash another rom, but it doesn't see the phone. ive already installed samsung drivers.
if i connect the charger, the battery indicator doesnt come up. it stays on that lined-circle screen forever, even after taking the USB cable out.
please help!
EDIT: added [Q] and added some more grammar errors.
any help is highly appreciated.
I had this same problem... The only thing that would fix it was this thing I had to buy called a Jig. It was less than $8 (with free shipping) on eBay.
http://www.ebay.com/itm/Fix-Download-Mode-USB-Jig-Samsung-Captivate-Galaxy-S-/140520601309
It delivered in 2 days and my phone is working perfectly now
just ordered one!
thanks!
one more thing, are you able to just install a different ROM through ODIN or ADB without having to do the full wipe? im wanting to save the contents of the internal SD.
thanks again
Hi all. I have searched for this problem and found some similar ones, but nothing quite like this.
The problem first started when I tried flashing Zedomax Kernel v3 via Odin. Odin reported a successful flash, but when it went to reboot it sat at the Galaxy S2 splash screen with yellow triangle for about 45 mins. I figured something was wrong so rebooted to CWM. I was able to get into both CWM and download mode at this point.
No matter what I tried I could not get the phone to boot up, so I thought I would try flashing a factory image to get back to out of the box settings. In the middle of this Odin got stuck on a step and then failed out after a good 10-30 minutes (sorry for lack of detail, this was pretty late last night).
Now, when I try to boot into recovery mode I see the [phone]....!....[computer] screen with the message "Firmware upgrade encountered" (part of this screen is cut off on the right, and appears to overflow to the left side? weird). I can boot into download mode, but Odin doesn't see my phone when I plug it in. The device doesn't show up in device manager either.
Things I have tried:
-Different USB port
-Kies "Resolution connection errors" button, which seems to reinstall the drivers
-Reboot computer after above step
-Remove battery from phone and replace
After these steps I still can't get my computer to see my plugged in phone in any way. I'm getting kinda nervous but the only thing giving me hope is that I can get it into download mode. Any ideas on how to get Odin to see it again?
Remove Kies and reinstall see if it picks the phone up and installs the drivers .
jje
OperationIvy85 said:
Hi all. I have searched for this problem and found some similar ones, but nothing quite like this.
The problem first started when I tried flashing Zedomax Kernel v3 via Odin. Odin reported a successful flash, but when it went to reboot it sat at the Galaxy S2 splash screen with yellow triangle for about 45 mins. I figured something was wrong so rebooted to CWM. I was able to get into both CWM and download mode at this point.
No matter what I tried I could not get the phone to boot up, so I thought I would try flashing a factory image to get back to out of the box settings. In the middle of this Odin got stuck on a step and then failed out after a good 10-30 minutes (sorry for lack of detail, this was pretty late last night).
Now, when I try to boot into recovery mode I see the [phone]....!....[computer] screen with the message "Firmware upgrade encountered" (part of this screen is cut off on the right, and appears to overflow to the left side? weird). I can boot into download mode, but Odin doesn't see my phone when I plug it in. The device doesn't show up in device manager either.
Things I have tried:
-Different USB port
-Kies "Resolution connection errors" button, which seems to reinstall the drivers
-Reboot computer after above step
-Remove battery from phone and replace
After these steps I still can't get my computer to see my plugged in phone in any way. I'm getting kinda nervous but the only thing giving me hope is that I can get it into download mode. Any ideas on how to get Odin to see it again?
Click to expand...
Click to collapse
That kernel is for the Epic touch 4g is that your phone or do you have the international version? If you flashed the wrong kernel it could cause problems.
Yes it's an Epic touch 4g from sprint.
EDIT: Uninstalled Kies, reinstalled Kies, restarted computer, still no kind of recognition of my phone in any state (powered off, at "Firmware upgrade encountered" screen it boots into, or in download mode). Starting to get nervous, I used to at least hear a sound when plugging my phone into my comp. It is like there is nothing on the other end of the USB cable.
More things I have tried:
-All of the above steps on a different computer
-Sweet talking it
-Talking dirty to it
Am I brick'd? I figure not, since I can at least get into download mode. Not sure what else I can do though. I'd go see what the Sprint store can do for me, but on the download mode screen it lists my custom binary download count as 5, I understand they will see that and tell me I'm out of luck?
OperationIvy85 said:
More things I have tried:
-All of the above steps on a different computer
-Sweet talking it
-Talking dirty to it
Am I brick'd? I figure not, since I can at least get into download mode. Not sure what else I can do though. I'd go see what the Sprint store can do for me, but on the download mode screen it lists my custom binary download count as 5, I understand they will see that and tell me I'm out of luck?
Click to expand...
Click to collapse
Try to reset your binary counter with a usb jig.
you could try and download the drivers again from here and see if it then connects
http://modem-techno.blogspot.com/2010/09/epic-4g-usb-driver-download.html
I also had a similar problem once with an old i9000 and what worked was doing this and then connecting the phone first and then opening Odin.For some reason opening Odin first and connecting wouldnt find the phone.If nothing else works try wipeing the bin counter with the jig and send it back.Youll have to say that kies crashed while updating on Win7 64bits.Samsung know that before the September 30th kies update kies wasnt fully functional with 64bit drivers and they had a few phones replaced under warranty because of crashing kies updates on Win7 64bits.
Thanks for the replies everyone.
I made a USB jig but it had no result. I checked the resistance with a multimeter and I am connected across pins 4 and 5 of the usb dongle I bought. I plug it in and nothing happens.
I can still get into download mode by the usual means, just no recognition from my computer, odin, or kies. Very frustrating. Am I going to have to buy a new one or is there another way to reset the bin counter?
EDIT: Got the USB jig to work! I was using a bad diagram and was on pins 1/2 instead of 4/5. Now I can't boot, can't get to recovery, can't get any PC to recognize my phone in download mode.. but at least my download screen says "Custom binary download: NO." So if nothing else works before tomorrow evening I'm gonna bring this thing back to the Sprint store and tell them what cooza said about kies crashing on win7 64 bit. Thanks everyone! Also I just realized there is a specific forum for Epic 4G touch.. sorry >.>
The good thing is that your bin counter is at "0" again.The Kies thing is the real deal as there are also posts here on XDA of the same thing happening.I also know its true from first hand experience as it has happened to me and when i told them about the Win7 64bit driver problem (this happened to me a couple of months back too) they had no option but to accept it cos they know its true.Also i offered to e-mail links from forums with other complaints from users on 64bit PCs but they didnt even dought my storey and in 4 days it was back in my hand.I told them that when the update finalized the programe froze and the phone rebooted to a black screen.Had to pull the battery cos it appeared to be dead and refused to reboot again.Important to say that you where on Kies prior to the update I mentioned.Ived update to the latest Kies and it works fine now on my Win7 64bit so be carefull there that date is important
Thanks cooza I really appreciate your help. I do have a couple questions though.
1. Is the update you are referring to an update to Kies software.. or an update to the Galaxy S2? Reason I ask is because my phone is the Epic 4G Touch (accidentally posted in this forum >.>), will they still believe my story?
2. Not sure if you will know the answer to this one, but should I go through Samsung tech support or can I take it back to the Sprint store where I bought it?
3. Just trying to get clear on the story I should tell them. I was using Kies to update my phone on a Win7 64bit computer, but I accidentally used the version of Kies from before the Sept. 30 update? And then the phone crashed resulting in it's current state. Correct? Anything else I should watch out for?
4. With the problem you are describing with Win7 x64, does the phone go into a soft brick where it won't boot up?
Thanks again.. you've been very helpful
OperationIvy85 said:
Thanks cooza I really appreciate your help. I do have a couple questions though.
1. Is the update you are referring to an update to Kies software.. or an update to the Galaxy S2? Reason I ask is because my phone is the Epic 4G Touch (accidentally posted in this forum >.>), will they still believe my story?
2. Not sure if you will know the answer to this one, but should I go through Samsung tech support or can I take it back to the Sprint store where I bought it?
3. Just trying to get clear on the story I should tell them. I was using Kies to update my phone on a Win7 64bit computer, but I accidentally used the version of Kies from before the Sept. 30 update? And then the phone crashed resulting in it's current state. Correct? Anything else I should watch out for?
4. With the problem you are describing with Win7 x64, does the phone go into a soft brick where it won't boot up?
Thanks again.. you've been very helpful
Click to expand...
Click to collapse
Kies via to its Sep 30th update was not fully compatable with 64bits and gave a lot of problems to a lot of people.I had a few problems with it when I got a new laptop (HP Win7 64bit) so started searching the web for solutions and found that kies was designed mainly to support the windowsXP versions 32bit and had caused Samsung to accept various repairs under warranty because of crashing Kies updates mainly on android running phones.For some reason Bada didnt seam to affected.Maybe cos there arnt to many around like android.In the 4G forum there is post from someone who has bricked their phone using Kies to update and a reply from another with the same problem.Take it into where you bought it to start with and if its not there problem then they might send it back to Samsung for you.All you need to say is that you where updating your firmware via kies and on completion it froze and the phone booted to a black screen like mine did.You had to pull the battery and restart your PC to close Kies cos it wouldnt close or minimize or anything.Tell them that you searched on the net for possible causes and found what i told you about Kies and since you have a Win7 64bits PC then thats most likely to have been the cause.Your bin counter is at 0 so there is no way they can counter-attack your story.
OperationIvy85 said:
Hi all. I have searched for this problem and found some similar ones, but nothing quite like this.
The problem first started when I tried flashing Zedomax Kernel v3 via Odin. Odin reported a successful flash, but when it went to reboot it sat at the Galaxy S2 splash screen with yellow triangle for about 45 mins. I figured something was wrong so rebooted to CWM. I was able to get into both CWM and download mode at this point.
No matter what I tried I could not get the phone to boot up, so I thought I would try flashing a factory image to get back to out of the box settings. In the middle of this Odin got stuck on a step and then failed out after a good 10-30 minutes (sorry for lack of detail, this was pretty late last night).
Now, when I try to boot into recovery mode I see the [phone]....!....[computer] screen with the message "Firmware upgrade encountered" (part of this screen is cut off on the right, and appears to overflow to the left side? weird). I can boot into download mode, but Odin doesn't see my phone when I plug it in. The device doesn't show up in device manager either.
Things I have tried:
-Different USB port
-Kies "Resolution connection errors" button, which seems to reinstall the drivers
-Reboot computer after above step
-Remove battery from phone and replace
After these steps I still can't get my computer to see my plugged in phone in any way. I'm getting kinda nervous but the only thing giving me hope is that I can get it into download mode. Any ideas on how to get Odin to see it again?
Click to expand...
Click to collapse
I also have this same problem now. Except that....I cannot even get into download mode. My phone is stuck at the [phone]....!....[computer] screen, but without any message. I am told that the exclamation mark tells Samsung that warranty is voided.
Is there anyway I can do anything to save my phone?
Who told you that the exclamation point means you voided your warranty?
bajaber said:
I also have this same problem now. Except that....I cannot even get into download mode. My phone is stuck at the [phone]....!....[computer] screen, but without any message. I am told that the exclamation mark tells Samsung that warranty is voided.
Is there anyway I can do anything to save my phone?
Click to expand...
Click to collapse
The exclamation point on a normal boot up screen (Galaxy S II splash screen) means there is a custom rom installed. This can be removed with a USB jig, which will also reset your custom binary counter.
I have absolutely no idea still what [phone]....!....[computer] means though. I ended up taking my phone back to the Sprint store and they replaced it for a small service charge while telling me next time I won't be so lucky. My next step was going to be to try calling Samsung with the story cooza suggested. I told that same story to the people at Sprint but they definitely didn't buy it, but you may have better luck with Samsung. If you get this resolved I'd be curious to hear how, but I am not optimistic for you
bajaber said:
I also have this same problem now. Except that....I cannot even get into download mode. My phone is stuck at the [phone]....!....[computer] screen, but without any message. I am told that the exclamation mark tells Samsung that warranty is voided.
Is there anyway I can do anything to save my phone?
Click to expand...
Click to collapse
The sign you see means that your phone is semi-bricked and that you needed a jig to force the phone to boot into download mode.You can buy one on ebay for a couple of bucks.Best you do cos it could may mean that your warranty is void.Let me explain,no one can actually say that your warranty is void because of this sign but being only "semi-bricked" the service centre are still able to enter the phone and see the bin counter.So if you semi-bricked flashing a non official firmware or you have done so earlier and your bin counter is not at 0 then YES your warranty is void.Semi-brick is not so bad as you can normally fix it yourself but Hard-brick is a dead phone and you gotta pay for a jtag .In your case buy a jig force the phone into download mode and re-flash it yourself.You shouldnt need to go anywhere.Semi-bricking is something you save yourself.Just wait till the jig arrives in the mail.
EDIT:there have been posts of people pulling the battery for 10min and re-trying and it has booted to download.They say they have had to do so 4 or 5 times for it to finally work but if youve got time on your hands then give it a try.
---------- Post added at 04:48 PM ---------- Previous post was at 04:22 PM ----------
OperationIvy85 said:
The exclamation point on a normal boot up screen (Galaxy S II splash screen) means there is a custom rom installed. This can be removed with a USB jig, which will also reset your custom binary counter.
I have absolutely no idea still what [phone]....!....[computer] means though. I ended up taking my phone back to the Sprint store and they replaced it for a small service charge while telling me next time I won't be so lucky. My next step was going to be to try calling Samsung with the story cooza suggested. I told that same story to the people at Sprint but they definitely didn't buy it, but you may have better luck with Samsung. If you get this resolved I'd be curious to hear how, but I am not optimistic for you
Click to expand...
Click to collapse
Well at least you got a phone now hope they didnt charge to much!!!!Good on ya mate
Update on my issue....
It turns out the problem is because I tried to flash an I1900 firmware while my phone is a G variant (I900G).
After using the right firmware, it worked.
OperationIvy85 said:
Thanks for the replies everyone.
I made a USB jig but it had no result. I checked the resistance with a multimeter and I am connected across pins 4 and 5 of the usb dongle I bought. I plug it in and nothing happens.
I can still get into download mode by the usual means, just no recognition from my computer, odin, or kies. Very frustrating. Am I going to have to buy a new one or is there another way to reset the bin counter?
EDIT: Got the USB jig to work! I was using a bad diagram and was on pins 1/2 instead of 4/5. Now I can't boot, can't get to recovery, can't get any PC to recognize my phone in download mode.. but at least my download screen says "Custom binary download: NO." So if nothing else works before tomorrow evening I'm gonna bring this thing back to the Sprint store and tell them what cooza said about kies crashing on win7 64 bit. Thanks everyone! Also I just realized there is a specific forum for Epic 4G touch.. sorry >.>
Click to expand...
Click to collapse
Hi, I'm having an exactly same problem with you and I just got a USB jig in mail, but even though I am following the instructions for the USB jig the counter is still not going back to 0 :/
This is the instruction I followed: take battery out for like a minute -> put the battery in but don't turn phone on -> put the usb jig in -> it's supposed to boot up with 0 flash count?
Mine still says 4... Can anyone please help?
sfoksn said:
Hi, I'm having an exactly same problem with you and I just got a USB jig in mail, but even though I am following the instructions for the USB jig the counter is still not going back to 0 :/
This is the instruction I followed: take battery out for like a minute -> put the battery in but don't turn phone on -> put the usb jig in -> it's supposed to boot up with 0 flash count?
Mine still says 4... Can anyone please help?
Click to expand...
Click to collapse
Is yours a i9100? If so is your firmware the latest 2.3.5 KI3 or KI8?
Could be your device has the new bootloader. If so check intratechs original firmware thread in original development section and install his old bootloader via Odin. Have a read while your there to get the latest info.
Good luck
Sent from my GT-I9100 using XDA App
aceofclubs said:
Is yours a i9100? If so is your firmware the latest 2.3.5 KI3 or KI8?
Could be your device has the new bootloader. If so check intratechs original firmware thread in original development section and install his old bootloader via Odin. Have a read while your there to get the latest info.
Good luck
Sent from my GT-I9100 using XDA App
Click to expand...
Click to collapse
Yeah, I got stuck while flashing 2.3.5 Gingerbread... Yeah I think it has a new bootloader, as I remember Odin updating the bootloader section before messing up.
Is there any way I can get the USB jig to work? My phone is no longer recognized by the USB anymore so I can't even flash another bootloader or anything.
Is there anythign I could do to make the USB jig work without connecting it to the computer?
Can you get into download mode using the buttons?
Volume down+home+power
If so try and flash another Rom from intratechs thread to get back to stock.
If that works you can try again.
Sent from my GT-I9100 using XDA App
i was trying to root a phone for someone and after odin completed it said it had failed.
the phone is a telus samsung t959d running froyo.
I followed the instructions from (I would post the url for the link but i am not allowed to.)cyanogenmod's wiki, after it failed I rebooted the phone and it got stuck on the screen in the attached pic. I have tried to boot back into download mode to no avail. From the screen it's stuck on I cannot get any tool to register the device as being present, adb, heimdall, zdiag, etc... I even tried fastboot out of desperation.Before I used odin I tried to get the phone to boot into the bootloader but it only ever went to either recovery or a normal boot and I tried every button press combo I could think of and found and nada.
Even running adb reboot bootloader just made the device boot normally. I think that if I could get it to boot to fastboot usb i could then try fastboot. I am new to rooting devices and have successfully rooted my HTC EVO3D and got s-off and simlock removed for any carrier. So I do know how to follow instructions properly, why flashing the recovery.bin failed I don't know and every fix I seem to find says BOOT TO DOWNLOAD MODE. if I could do that I wouldn't be having this problem lol. Anyway can someone please help me figure this out. Thanks. ANd if you need any further info please let me know. I don't want to have to give my friend my phone due to a software issue.
And YES I did pick PDA not anything else.
machv5 said:
i was trying to root a phone for someone and after odin completed it said it had failed.
the phone is a telus samsung t959d running froyo.
I followed the instructions from (I would post the url for the link but i am not allowed to.)cyanogenmod's wiki, after it failed I rebooted the phone and it got stuck on the screen in the attached pic. I have tried to boot back into download mode to no avail. From the screen it's stuck on I cannot get any tool to register the device as being present, adb, heimdall, zdiag, etc... I even tried fastboot out of desperation.Before I used odin I tried to get the phone to boot into the bootloader but it only ever went to either recovery or a normal boot and I tried every button press combo I could think of and found and nada.
Even running adb reboot bootloader just made the device boot normally. I think that if I could get it to boot to fastboot usb i could then try fastboot. I am new to rooting devices and have successfully rooted my HTC EVO3D and got s-off and simlock removed for any carrier. So I do know how to follow instructions properly, why flashing the recovery.bin failed I don't know and every fix I seem to find says BOOT TO DOWNLOAD MODE. if I could do that I wouldn't be having this problem lol. Anyway can someone please help me figure this out. Thanks. ANd if you need any further info please let me know. I don't want to have to give my friend my phone due to a software issue.
And YES I did pick PDA not anything else.
Click to expand...
Click to collapse
I kept reading other threads and sadly I din't pully the battery first before disconnecting the usb and repartition may have been checked as I see that it does the as default for my version. Also i turned off ODIN as I was hoping a reboot of my computer might help. I will keep trying to find an answer till someone gets back to me. this post may not even show up if I can't do a second post if no one has replied first.
Everyone was a nub at one time wasn't it FUN hahahahahaha sob cry
machv5 said:
I kept reading other threads and sadly I din't pully the battery first before disconnecting the usb and repartition may have been checked as I see that it does the as default for my version. Also i turned off ODIN as I was hoping a reboot of my computer might help. I will keep trying to find an answer till someone gets back to me. this post may not even show up if I can't do a second post if no one has replied first.
Everyone was a nub at one time wasn't it FUN hahahahahaha sob cry
Click to expand...
Click to collapse
I tried a jig and that didn't work. There must be some way of getting the device to give up on completing a task i no longer can give it due to ODIN being shut off.
Why is it that the "how to root/unlocks" never have the "if x fails then do these steps etc..." Had the how to had "pull the battery before disconnecting USB and don't reset or shut off ODIN" I wouldn't be in this mess. I realize that it's user beware but a few important steps like that in case of a fail would go a long way to you guys not shaking your heads. Instead of "silly nub hahahahahaha". No offence but I get that a lot and try to remember that when I teach someone how to use a computer. I am new at phones not at everything.
Further Developments Please can someone help?
I was giving someone a new memory card and they had a Samsung SGH-I896 it has an EB575152VA battery and the one I have the T959D has an EB575152VU battery. I exchanged my battery for hers by accident somehow and when I plugged my phone in it didn't go to the phone triangle computer logo screen it booted to recovery and said it couldn't charge the battery and kept rebooting to recovery. I got my battery back and it booted back to the phone triangle computer logo again. Grrrr....
The other thing I saw while the recovery screen was an error message that said
Code:
E:/data/fota not accessible
(may not be 100% accurate I don't have the battery to check right now but can get it again if need be) anyway I now see that there may be some light at the end of the tunnel. i have the correct stock firmware for the device I tried flashing it while in recovery but the phone kept rebooting before anything got done. My question is how can I get the dang phone to stop asking for Odin and go to recovery so I can flash stock firmware and ROM back to it? As I cannot as far as I know give it what it wants because I reset Odin and nothing seems to see that the phone is connected to the computer. I am going to try the other battery on a full charge to see what that does.
I am new at all this and want to get it fixed. I cannot afford to send it off to a service center and besides that I want to do it myself as I want to become a developer and droid technician. I would gladly donate to anyone but am still trying to get Google to accept my pay-as-you-go credit card and I don't have PayPal either. Which is really frustrating when it comes to giving back. I posted a Q&A on how to without PayPal or CC but as of the last time I checked no one has gotten back to me about it.
The CyanogenMod guide is flat out WRONG. I've tried to change it, but anything I do is reverted in an instant. I also tried to use it to install the ROM only, ended up bricking my phone and it took me hours to unbrick. That's how I became acquainted with XDA.
So, to get this straight:
1. you're using the stock USB cable
2. you remove the battery
3. you hold volume down
4. you plug in the usb cable
5. after a few seconds, you release volume down
6. the screen does not display a yellow triangle with an android
Posted from my Galaxy Tab with CM10
MultipleMonomials said:
The CyanogenMod guide is flat out WRONG. I've tried to change it, but anything I do is reverted in an instant. I also tried to use it to install the ROM only, ended up bricking my phone and it took me hours to unbrick. That's how I became acquainted with XDA.
So, to get this straight:
1. you're using the stock USB cable
2. you remove the battery
3. you hold volume down
4. you plug in the usb cable
5. after a few seconds, you release volume down
6. the screen does not display a yellow triangle with an android
Posted from my Galaxy Tab with CM10
Click to expand...
Click to collapse
That is correct. If you think that my idea below is a bad one or if I downloaded the wrong firmware package please let me know and /or you have a fix that will work? ty
I have though come up with an idea that may work. I am going to charge the "wrong" battery in erm the right phone lol and then use it to trick the device into booting into recovery instead of the cellphone triangle computer (CTC, for want of a better acronym) The I896 battery ends in a V not an ? (sorry can't rem don't have it on me) from the I896 model I think it is, plugging it into USB with the power off sends it to recovery with the "battery cannot be charged " message instead of the CTC screen.
I tried it but the charge in the battery was too low and rebooted. I am hoping that with a full charge (as long as I don't power on the phone first as this will make it go to CTC logo again.
I am hoping that I can install the update.zip that I made by first unzipping the T959UVJFD_firmware.tar I downloaded then unpacked and then repacked into an update.zip as I don't think that it will read the package as a tar file and if it's not called update.zip The recovery is still stock. If I get the phone working I am not going to try unlocking and rooting it again. I will just post two separate adverts one as a carrier locked device and the other one (higher of course to cover buying the unlock from Telus) as carrier unlocked and then I will buy the unlock code if the blah blah you get the drift. sorry for rambling on.
oh and I can't rem if I said this or not, In recovery it "E:/data/fota not accessible" I don't know what that means yet I have been busy with other things and haven't looked it up yet.
Since you can get into at least some version of recovery, your bootloader is intact and you should be able to unbrick it. You ought to be able to get into download mode using a download jig. You can get one on ebay for a few bucks or you can make one yourself. There's a guide floating around here somewhere that lets you make one from a microusb cable.
Posted from my Galaxy Tab with CM10
After doing a software update the phone keeps getting stuck on the boot screen. Any idea what can be wrong or could be done?
It's the Korean LTE version that I brought back after living in Seoul. After it bugged out I tried the boot up menu (power, home, vol up) and tried a factory reset, but it seems the faulty software update is stuck.
I bought it in a Korean store and I don't have any manuals, computer software or boxes left. I am guessing I have to connect it to my computer and use it as an external source for the software update, but I am not sure on how to do this. Is there possibly a guide for my problem?
Best regards, Olof
Edit:
I have tried the factory reset and the wipe cache option without any success.
I have also tried using Kies to connect but it seems to be unable to reach the phone. Windows detects the device and tries to install drivers, but fails during. It's weird because I've used the USB cable previously and the drivers should still be in the system (win7).
I have not rooted or flashed or made anything like that. I bought it in a Korean store and I am not sure if they might have done something to it.
I would try flashing stock firmware, also try asking in shv-e210l forum this is the int'l s3 forum.
ghostofcain said:
I would try flashing stock firmware, also try asking in shv-e210l forum this is the int'l s3 forum.
Click to expand...
Click to collapse
I figure I have to go there sooner or late although I don't quite know how to do it.
Are there any moderators that could move the thread perhaps?
This problem has been driving me absolutely mental. About 2 months ago, I tried to root my Galaxy Tab 4 8.0 by T-Mobile (it was an old device anyways), I used the Odin method, and while it was installing, it said that the process was successful, and I saw it all come through. However, when my device restarted, it was stuck at "Starting apps..." for about an hour, so I tried restarting. Then it was stuck on the T-Mobile logo for 1.5 hours. I did a hard wipe/reset, and it was fine... for about a week.
The funny thing about it is, after I did the hard reset, certain bugs would happen, a different bug each time. (For example, Google Play apps would be stuck at "installing", screenshots wouldn't save, apps would crash repeatedly, etc) So if I tried to restart, it wouldn't fix it, but instead it would bootloop. I have to hard reset/wipe my whole system each time it happens, and it drives me up the friggin wall.
I saw online that you can try flashing your system by installing the default drivers onto your computer, and install it on your system through Odin. (or something like that, I'm not that professional at mobile technology) Awesome. Just one problem.. I have looked everywhere and I can't find the driver specifically for my system. I have looked for the driver ever since the problem got worse and I found out about this information, but I found nothing.
If anyone has any idea on how you can help, please respond as soon as you can. Thank you very much.
iamnekro said:
This problem has been driving me absolutely mental. About 2 months ago, I tried to root my Galaxy Tab 4 8.0 by T-Mobile (it was an old device anyways), I used the Odin method, and while it was installing, it said that the process was successful, and I saw it all come through. However, when my device restarted, it was stuck at "Starting apps..." for about an hour, so I tried restarting. Then it was stuck on the T-Mobile logo for 1.5 hours. I did a hard wipe/reset, and it was fine... for about a week.
The funny thing about it is, after I did the hard reset, certain bugs would happen, a different bug each time. (For example, Google Play apps would be stuck at "installing", screenshots wouldn't save, apps would crash repeatedly, etc) So if I tried to restart, it wouldn't fix it, but instead it would bootloop. I have to hard reset/wipe my whole system each time it happens, and it drives me up the friggin wall.
I saw online that you can try flashing your system by installing the default drivers onto your computer, and install it on your system through Odin. (or something like that, I'm not that professional at mobile technology) Awesome. Just one problem.. I have looked everywhere and I can't find the driver specifically for my system. I have looked for the driver ever since the problem got worse and I found out about this information, but I found nothing.
If anyone has any idea on how you can help, please respond as soon as you can. Thank you very much.
Click to expand...
Click to collapse
What you read in the internet means re-flashing your stock rom (system), that is the fix for your problem, the way to do it is to download and install Samsung USB drivers if you hadn't done that already, and Download stock rom from here or here search your model number in the search box and choose the stock rom based on your country, and flash with Odin, it's pretty much the same way you tried to root using CF-ROOT method:
1-you boot into download mode (volume down + home button + power button)
2-and then connect your phone to PC.
3-open Odin and uncheck everything except "auto reboot" and "F. Reset Time" (you should find it like that already), make sure your phone is recognized by Odin, you will see a blue box with a message saying "0:[COMX]" where X is a number.
4-press AP (or PDA in some versions) locate your stock rom which should be in .md5 format, and choose it, then 5-press start.
6-wait for the process to finish (takes a while) and then the phone should reboot itself and you will get a message in Odin saying "Reset!"
PS: you must register on the sites to download..bad thing i know but it's obligation.
Searched both of these websites for the drivers, found nothing.. I've been searching the internet for hours and not one driver was found. Extremely disappointed.
iamnekro said:
Searched both of these websites for the drivers, found nothing.. I've been searching the internet for hours and not one driver was found. Extremely disappointed.
Click to expand...
Click to collapse
Give me your model number.
Sorry found it in the thread title
@iamnekro
That is the link from the first site:
SM-T337T latest firmware android 5.1.1
That is the link from the second site:
SM-T337T latest firmware android 5.1.1
Obviously you didn't search at all...LOL
PS: It's called Stock Firmware or Stock ROM.... not Drivers
Register on any of the sites first to download.
And press the thanks button please
Regards Migo
I'll have to close the thread.. my computer isn't that advanced and is low on space anyways...
iamnekro said:
I'll have to close the thread.. my computer isn't that advanced and is low on space anyways...
Click to expand...
Click to collapse
It doesn't need any advanced computer and only the size of the stock rom and Odin, it's no big deal.