I recently replaced the screen and lcd on my rezound, however after doing so it seems that the nav buttons no longer light up, also my screen within 3-4 days now accumulates excessive dust under the screen. I'm not sure whether the nav buttons normally do not light up after the lcd get replaced because the same thing happened when changing it on my droid incredible.
However the real question is how to stop this dust. I have opened and cleaned it multiple times and even made sure everything was nice and tight (i.e. no missing screws and stuff) Any ideas on how to fix these problems?
Do you have the adhesive layer between the digitizer and LCD?
I have the same issue with my phone, I really miss the lights. I'm about to open it up and see if I can see why...
And about the screen, you got the digitizer + glass combo right? I have the same thing. Try taking the glass off, use compressed air to get everything off the screen then make sure it's a tight fit with the adhesive when you put it back on lol.
In the general section there's a thread from a while ago about replacing the digitizer. You might get some tips from that if you can find it.
Here's a few:
http://forum.xda-developers.com/showthread.php?t=2046140&highlight=replace+digitizer
http://forum.xda-developers.com/showthread.php?t=1698329&highlight=replace+digitizer
http://forum.xda-developers.com/showthread.php?t=1938836&highlight=replace+digitizer
Related
Just finished replacing my cracked glass / digitizer, but now my previously working LCD just shows vertical colored lines. I bought one of the glass / digitizer replacements from Ebay, which was a perfect match for the OEM piece. Since I was having trouble finding the thin double sided tape, I used black silicone adhesive to bond the LCD to the digitizer. When I plugged in LCD panel and turned the tablet on, all I get is vertical varying colored lines across the LCD. I've pressed the on /off switch for 10 seconds to reboot the device, but it still does the same thing. I've taken the ribbon cable off and on checking to see if was not properly seated, but it seems to be okay. Any ideas?
The ribbon cable had a 90 degree bend in it after it was removed... can that cause an internal cut in the cable itself? At least to me, it appears that the LCD is working, since the lines are bright in color and even change as you manipulate the digitizer... it just has no picture.
Thanks..
Killer95Stang said:
Just finished replacing my cracked glass / digitizer, but now my previously working LCD just shows vertical colored lines. I bought one of the glass / digitizer replacements from Ebay, which was a perfect match for the OEM piece. Since I was having trouble finding the thin double sided tape, I used black silicone adhesive to bond the LCD to the digitizer. When I plugged in LCD panel and turned the tablet on, all I get is vertical varying colored lines across the LCD. I've pressed the on /off switch for 10 seconds to reboot the device, but it still does the same thing. I've taken the ribbon cable off and on checking to see if was not properly seated, but it seems to be okay. Any ideas?
The ribbon cable had a 90 degree bend in it after it was removed... can that cause an internal cut in the cable itself? At least to me, it appears that the LCD is working, since the lines are bright in color and even change as you manipulate the digitizer... it just has no picture.
Thanks..
Click to expand...
Click to collapse
90 degree bends can cause one or more of the individual conductors to become broken. I've had it happen on hard drive cables, and one inside a sprinkler system once.
chamberc said:
90 degree bends can cause one or more of the individual conductors to become broken. I've had it happen on hard drive cables, and one inside a sprinkler system once.
Click to expand...
Click to collapse
Any way to actually test this? Can use a voltmeter type tester to check continuity from one side of each pin to the other? They are hair like in size, so not sure the standard tests are the same.
Thanks..
My DIY experience...
Hi,
How did you perform the screen replacement? I have tried and I have described it below.
It seem like there are a lot of people that has TF201s with broken screens, but very little information about how to DIY screen replacement, so I wanted to post my experience here.
The screen on my TF201 cracked (dropped on the floor - only the screen was damaged, the LCD and digitizer still worked) so I seached around the web to find ways to replace the screen - without luck
I did find instructions on how to open the device and I also found original glass/digitizer replacement parts on eBay originating from China at about $100 so I took the chance and ordererd a new screen. It arrived 2 weeks after and looked good.
With the instructions on how to disassemble the TF201, it was quickly open and the glass/digitizer/LCD is one subassembly connected to the mainboard with two flex cables - one for the LCD and one for the digitizer.
Next step is to power off the system internally. There is a small internal switch in the lower left corner that you should switch to the off position. The LCD and digitizer cables can now be disconnected from the mainboard. The connectors open easily by putting a nail under the white frame of the correctors and pulling the frame up and then pull out the flex cables. You now have the glass/digitizer/LCD separated from the mainboard.
The LCD has a few screws to hold it to the plastic frame - these should be removed at this step. Mine only has two screws mounted although there are room for more (bad assembly quality or a fix for screen bleeding???)
Now comes the hard part and the part where I failed! There is a plastic frame around the edges of the glass that you need to remove and mount on the new glass. This plastic part holds all the taps that keep the tablet together and it is taped to the glass with some VERY sticky tape!
I used a knife to cut between the plastic and the glass with the result that the glass broke in tiny pieces as I went around, but as I saw no other way I kept going... It might have been better to use a heat gun or a hairblower to heat up the glue before trying to remove it, bu I was worried that the LCD might be damaged by the heat.
The plastic frame has to be removed first to have access to the foam tape that is used to tape the LCD to the glass/digitizer. Once the plastic frame was off, I again used the knife to gently cut the foam tape (around 1 mm thick) all around the LCD screen so that this can be removed from the glass.
Here I might have made my second mistake. I was worried that I would cut too deep into the foam and hit the LCD screen, but the foam at the bottom of the screen is a little wider than the rest and as I tried to remove the screen I used too much force and might have damaged the LCD - the end result was that also the LCD was damaged in the process. The damage might also have been caused by me pressing too hard on the screen during the removal of the plastic frame (might actually be more likely as the glass was broken across the screen and the damage I was seing when I turned on the screen was following the same line).
Well, I got the LCD off the broken screen and though I had been successfull even thought it had taken a couple of hours to get there (I could not visually see that the LCD was damaged at this point). Then on to the assembly with the new screen/digitizer! I had some double sided tape that I used to tape the screen to the plastic, but desided to to a quick test before I fully assembled the unit and this turned out to be a good idea!
I mounted the LCD screen with just the screws and connected the flex cables back into the connectors (these can be a little tricky to get it, so just be patient and keep wiggling them in and close the latches). I enabled the power again and pressed the power botton and: DAMM - THE LCD IS BROKE!!!!
After wiglling a little with the LCD cable I was able to get a partial image, but it was evident that I had mishandled the LCD screen during the disassembly and I needed a new screen to gt my tablet working again - now I was glad that I did not glue the LCD to the glass, so that I needed both a new LCD and a new glass/digitizer!
Off to the web to seach for a replacement LCD screen... Hmm, lots of ebay listings for replacement LCDs, but none of them looked like the original I had, but when seaching for the partnumber on the LCD I took out (Hannstar HSD101PWW2 rev. 0-A00) I did find a few priced around $100
Before I started to spend more money on the device I wanted to check our if the digitizer was actually working, so I connected the tabled to my TV using the HDMI output to test...WHAT?? THE X-AXIS WAS REVERTED!!!
I double checked the flex cable connections, but everything was in order. I then compare my broken screen with the replacement part and noticed that the signal routing on the flex cable for the new part looked quite different than the original.
I emailed the company that sold me the screen and he replied back that they JUST heard that some other customer have had the same problem - there might be different versions for the digitizer used in the TF201 (perhaps depending on production time)!!!
He suggested that I tried a hard reboot and a system reset to default and I tried that without luck.
I also tried to find a 5 point screen calibration routine, but this does not seem to be supported.
Does anyone know of a way to revert the x axis by modifying a configuration file - and can that be done without rooting the device??
They did offer to refund the price of the screen if I shipped the screen back to them, but I will most likely damage the screen when trying to remove the plastic frame and it will cost me shipping the part back to China...
Did you test if the touch screen is actually working on your reworked unit (you can use the HDMI output as I did)?
Unless I get the screen issue resolved I most likely will get a TF700 instead of my broken prime - I really loved the prime for the 4 months I had it working...
ThomasKJ said:
Hi,
How did you perform the screen replacement? I have tried and I have described it below.
It seem like there are a lot of people that has TF201s with broken screens, but very little information about how to DIY screen replacement, so I wanted to post my experience here.
The screen on my TF201 cracked (dropped on the floor - only the screen was damaged, the LCD and digitizer still worked) so I seached around the web to find ways to replace the screen - without luck
I did find instructions on how to open the device and I also found original glass/digitizer replacement parts on eBay originating from China at about $100 so I took the chance and ordererd a new screen. It arrived 2 weeks after and looked good.
With the instructions on how to disassemble the TF201, it was quickly open and the glass/digitizer/LCD is one subassembly connected to the mainboard with two flex cables - one for the LCD and one for the digitizer.
Next step is to power off the system internally. There is a small internal switch in the lower left corner that you should switch to the off position. The LCD and digitizer cables can now be disconnected from the mainboard. The connectors open easily by putting a nail under the white frame of the correctors and pulling the frame up and then pull out the flex cables. You now have the glass/digitizer/LCD separated from the mainboard.
The LCD has a few screws to hold it to the plastic frame - these should be removed at this step. Mine only has two screws mounted although there are room for more (bad assembly quality or a fix for screen bleeding???)
Now comes the hard part and the part where I failed! There is a plastic frame around the edges of the glass that you need to remove and mount on the new glass. This plastic part holds all the taps that keep the tablet together and it is taped to the glass with some VERY sticky tape!
I used a knife to cut between the plastic and the glass with the result that the glass broke in tiny pieces as I went around, but as I saw no other way I kept going... It might have been better to use a heat gun or a hairblower to heat up the glue before trying to remove it, bu I was worried that the LCD might be damaged by the heat.
The plastic frame has to be removed first to have access to the foam tape that is used to tape the LCD to the glass/digitizer. Once the plastic frame was off, I again used the knife to gently cut the foam tape (around 1 mm thick) all around the LCD screen so that this can be removed from the glass.
Here I might have made my second mistake. I was worried that I would cut too deep into the foam and hit the LCD screen, but the foam at the bottom of the screen is a little wider than the rest and as I tried to remove the screen I used too much force and might have damaged the LCD - the end result was that also the LCD was damaged in the process. The damage might also have been caused by me pressing too hard on the screen during the removal of the plastic frame (might actually be more likely as the glass was broken across the screen and the damage I was seing when I turned on the screen was following the same line).
Well, I got the LCD off the broken screen and though I had been successfull even thought it had taken a couple of hours to get there (I could not visually see that the LCD was damaged at this point). Then on to the assembly with the new screen/digitizer! I had some double sided tape that I used to tape the screen to the plastic, but desided to to a quick test before I fully assembled the unit and this turned out to be a good idea!
I mounted the LCD screen with just the screws and connected the flex cables back into the connectors (these can be a little tricky to get it, so just be patient and keep wiggling them in and close the latches). I enabled the power again and pressed the power botton and: DAMM - THE LCD IS BROKE!!!!
After wiglling a little with the LCD cable I was able to get a partial image, but it was evident that I had mishandled the LCD screen during the disassembly and I needed a new screen to gt my tablet working again - now I was glad that I did not glue the LCD to the glass, so that I needed both a new LCD and a new glass/digitizer!
Off to the web to seach for a replacement LCD screen... Hmm, lots of ebay listings for replacement LCDs, but none of them looked like the original I had, but when seaching for the partnumber on the LCD I took out (Hannstar HSD101PWW2 rev. 0-A00) I did find a few priced around $100
Before I started to spend more money on the device I wanted to check our if the digitizer was actually working, so I connected the tabled to my TV using the HDMI output to test...WHAT?? THE X-AXIS WAS REVERTED!!!
I double checked the flex cable connections, but everything was in order. I then compare my broken screen with the replacement part and noticed that the signal routing on the flex cable for the new part looked quite different than the original.
I emailed the company that sold me the screen and he replied back that they JUST heard that some other customer have had the same problem - there might be different versions for the digitizer used in the TF201 (perhaps depending on production time)!!!
He suggested that I tried a hard reboot and a system reset to default and I tried that without luck.
I also tried to find a 5 point screen calibration routine, but this does not seem to be supported.
Does anyone know of a way to revert the x axis by modifying a configuration file - and can that be done without rooting the device??
They did offer to refund the price of the screen if I shipped the screen back to them, but I will most likely damage the screen when trying to remove the plastic frame and it will cost me shipping the part back to China...
Did you test if the touch screen is actually working on your reworked unit (you can use the HDMI output as I did)?
Unless I get the screen issue resolved I most likely will get a TF700 instead of my broken prime - I really loved the prime for the 4 months I had it working...
Click to expand...
Click to collapse
I was in the same boat as you... after I took apart the unit, I still had a functioning screen... but when I went further to separate the LCD from the digitizer, I must have damaged the LCD. Right now all I get are vertical colored lines. I need to get an HDMI cable so I can check the function of the digitizer.. It seems to work, because I do get color changes when its manipulated, but no image. Damm.. problem is... how much good money do I spend on a damaged device.. At this point, I wish I just sent it in to get fixed by Asus..
Killer95Stang said:
I was in the same boat as you... after I took apart the unit, I still had a functioning screen... but when I went further to separate the LCD from the digitizer, I must have damaged the LCD. Right now all I get are vertical colored lines. I need to get an HDMI cable so I can check the function of the digitizer.. It seems to work, because I do get color changes when its manipulated, but no image. Damm.. problem is... how much good money do I spend on a damaged device.. At this point, I wish I just sent it in to get fixed by Asus..
Click to expand...
Click to collapse
I'm not sure that your LCD is broken. It might just be the connection to the motherboard that is bad as chamberc said. I had the same problem with my broken screen. I had to wiggle the cable to get a partial correct picture on my screen. I tried to clean the pads without getting a 100% stable connection so I might have broken the flex cable as well, but normally these are relatively good at flexing without braking (they are made to do that) so I tend to think that it is the connection in the connector.
Until I figure out what to do with the touch screen I have not spend more time on root casuing it, but I suggest that you try to take the flex out of the connector and clean it with either a erasor or a cloth with alcohol and then gently put it back into the connector. Also ensure that you put it in the right way and close the hatch properly.
Good luck.
On the touch screen issue, my touch screen is working fine it JUST has a reverted x-axis, so it would still cause your colors to change, so I'm very curious if yours is working. Could you also share the touch screen part number (printed on the flex cable) and TF201 hardware version (TF201-1B or TF201-1I or???) This should be written on the label of the box and on the warrenty card.
The background for me asking about this, is that asusparts.eu has different spare parts depending on if is for TF201-1B or TF201-1I so there might be two versions of the hardware out there. Mine is a TF201-1B.
So I dropped my phone today, and it must have fell on the corner good enough that it cracked the screen from the top-left to the middle-right.
Going to replace the digitizer/LCD as a combo since it's a bit easier than replacing just the digitizer.
Ordered this today:
http://www.ebay.com/itm/350582267363?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1438.l2649
Watched a couple of the repair videos (specifically this one: http://blog.repairsuniverse.net/how-to-fix-htc-rezound-screen/), and they say that there's adhesive on the back of this assembly as well that you need to pry away from (in the previously linked video, they push the assembly away from the housing from the backside and pry away from the housing/adhesive). My question is... am I going to have to replace this adhesive once I pry the assembly away from the housing? Or should the adhesive that's there be good enough to secure it as long as I don't rip it away very badly?
If I do need to get new adhesive, anybody have any links as to what to get?
Thanks in advance, I appreciate it!
I never replace a screen before. good luck
Bump.
Still haven't done this, as I haven't had time on the weekends yet. Got a GNexus to get me by, but I'm missing my Rezound.
http://www.amazon.com/gp/product/B0069YNZV2/ref=oh_details_o00_s00_i00?ie=UTF8&psc=1
doing all this is very tedious work... make sure you get the soft button hinges in correctly or the screen wont sit flat..
agentofchaos said:
http://www.amazon.com/gp/product/B0069YNZV2/ref=oh_details_o00_s00_i00?ie=UTF8&psc=1
doing all this is very tedious work... make sure you get the soft button hinges in correctly or the screen wont sit flat..
Click to expand...
Click to collapse
Should be less tedious since I got the LCD/Digitizer assembly together, so I don't have to replace just the digitizer.
I replaced the digitizer on mine last year. The process was just a disaster for me (ended up cracking my LCD)...but since yours is coming with the LCD and digitizer already glued together...perhaps you should have some better luck. It won't be necessarily difficult to do...it could just become a pain.
For one...there are clear tabs attached to the digitizer that essentially "draw" the red LED lights from the board down to the buttons on the bottom. These tabs are literally sandwiched between the digitizer and LCD...you'll see what I mean when you separate the broken digitizer/LCD from the housing...there will be 4 clear tabs sticking out from the bottom of the LCD. I did not find any seller that was selling those tabs, and it's quite possible the one you bought won't have them. What this means is...the 4 capacitive buttons along the bottom will still work, they just won't light up anymore. Not a big deal to some. I tried peeling them off my old digitizer and gluing them to the new one...but that didn't come out right at all. And your new LCD/digitizer will already be glued together and you're probably not going to want to separate them just to try and save the buttons.
Secondly, I've used the 3m double-sided roll of tape (like the one linked to above). It'll probably be your best bet...but know that, you could possibly need to redo it after a while of use. I could push on the top of my screen with my thumb, and I would see it kinda "flex" a bit, so the tape wasn't holding all too well. I'd also get fuzz and dirt on the screen of the front camera over time. So do a good, thorough job taping the digitizer/LCD down to the housing.
I lucked out (sort of) because my wife decided to give her Rez a bath and killed it. So I essentially took her digitizer, LCD and housing and use it on my phone.
OH, and don't overtighten the 6 screws for the red back housing! The bottom two screws especially. I did that and it cracked. And be gentle removing the red housing from the camera..sometimes the camera likes to get stuck inside of the camera housing and prying it apart will destroy it.
OpAckTool said:
I replaced the digitizer on mine last year. The process was just a disaster for me (ended up cracking my LCD)...but since yours is coming with the LCD and digitizer already glued together...perhaps you should have some better luck. It won't be necessarily difficult to do...it could just become a pain.
For one...there are clear tabs attached to the digitizer that essentially "draw" the red LED lights from the board down to the buttons on the bottom. These tabs are literally sandwiched between the digitizer and LCD...you'll see what I mean when you separate the broken digitizer/LCD from the housing...there will be 4 clear tabs sticking out from the bottom of the LCD. I did not find any seller that was selling those tabs, and it's quite possible the one you bought won't have them. What this means is...the 4 capacitive buttons along the bottom will still work, they just won't light up anymore. Not a big deal to some. I tried peeling them off my old digitizer and gluing them to the new one...but that didn't come out right at all. And your new LCD/digitizer will already be glued together and you're probably not going to want to separate them just to try and save the buttons.
Secondly, I've used the 3m double-sided roll of tape (like the one linked to above). It'll probably be your best bet...but know that, you could possibly need to redo it after a while of use. I could push on the top of my screen with my thumb, and I would see it kinda "flex" a bit, so the tape wasn't holding all too well. I'd also get fuzz and dirt on the screen of the front camera over time. So do a good, thorough job taping the digitizer/LCD down to the housing.
I lucked out (sort of) because my wife decided to give her Rez a bath and killed it. So I essentially took her digitizer, LCD and housing and use it on my phone.
OH, and don't overtighten the 6 screws for the red back housing! The bottom two screws especially. I did that and it cracked. And be gentle removing the red housing from the camera..sometimes the camera likes to get stuck inside of the camera housing and prying it apart will destroy it.
Click to expand...
Click to collapse
Thanks for the heads up.
Swapped out the screen (didn't get any 3M tape yet, but I wanted to make sure the screen worked properly / multi-touch was recognized everywhere).
Swapped the screens, re-assembled (managed to leave some adhesive where the lcd/digitizer assembly pulls out of on there, so it sticks, but like what happens with you it flexes just a bit. Will probably order some 3M tape one of these days and take off all of the old adhesive and replace it. Glad you mentioned the issue with the camera getting stuck in the housing; that did happen to me, and I had to work it out of there. The tiny LED board did pop out of it's connector, but I popped it back in easily and it still works fine.
I also didn't put the soft-key light tabs in the new LCD/digitizer (like you said, didn't want to pry the new one apart). Doesn't bother me much anyway, as I had them turned off in my ROM anyway lol.
So far it works well. Won't be my daily again yet until I have some 3M tape to put on there so the assembly is secured in the housing.
Just an update. Got some double-sided tape, and scraped off the old, remnants of the previous tape that was there. Cut new strips to fit where the old ones were, and it fits much more securely now. No screen flex or wiggle anymore. Charging it back up, and thinking about flashing a different ROM now that I have it fixed.
All-in-all, it was a pretty easy fix.
Alright, so I love my Rezound, even if I bought it used. There's one issue though. There's quite a bit of dust under the digitizer, to the point where there are little clumps (?) of dirt / dust there (like a couple mm's in diameter). My screen messes up quite a bit, in that the touch messes up and spazzes out, doing random things. It happens A LOT in sunlight and it's frustrating, especially with a pattern unlock, as I can be locked out or it goes int the emergency call area and dials random crap sporadically. If I turn the screen off and tap it it stops. I'm thinking about cleaning the digitizer off, and I don't want to replace the whole thing. Could the dust be the cause of these issues I'm having? I know that dust is conductive apparently so it's possible, right?
I got this phone for $95 bucks (everything besides the screen dust is in near perfect condition), so warning me about just taking apart the digitizer doesn't bother me. I can do this.
It sounds like someone replaced the digitizer or LCD and didn't route or properly connect the digitizer flex cable. Search this sub forum for "digitizer replacement" or "screen repair" to avoid some of the gotca's when taking the phone apart (such as dealing with the cables and the sticky tape holding the screen & digitizer in the phone)
Hey!
A few months ago I dropped my SK17 and the screen cracked. Despite being cracked and with pieces falling apart, the screen worked perfectly. Yesterday I dropped my phone again and it stopped responding to touch. The screen looks exactly as before falling but it stopped responding to touch. The soft keys still work. Will replacing the screen solve the problem? I already flashed my phone to an original firmware but it solved nothing. I don't mind replacing the screen and spending a few bucks to get my phone working but I'd like to be sure if the problem's in the lcd.
Well, yeah, your touch digitizer might have hit it's stress breakpoint. Replacing the screen assembly will do the trick.
In case you didn't know, the display and touch glass are glued on the xmp, which makes replacements more expensive than expected. But whatever the cost is, it's better to spend ~35 bucks and restore your phone's full functionality than to keep using it like a brackberry haha.
Be extremely careful if you plan on replacing it yourself. Look around for the best/most trusted repair shop/center if you plan on sending it to someone else for repair. You really don't want to deal with wonky touch response or bad color reproduction because of a cheap replacement part, I know, I've been there.
Thanks, I was thinking in replacing the screen myself. I've already disassembled the phone up to the screen but I didn't took it off. Is it hard to take it off and put the new screen on? Do I have to glue it to the front cover?
Ok, if you have dissasembled the phone and assembled it back successfully, you already know the basic structure, so that's good.
The screen assembly is glued to the plastic + metal frame, and it's pretty hard to pry it apart. Make sure to use non-metallic prying tools and a heat gun (a hair drier will do fine). Using a heat gun gives you a chance to reuse the original double-sided tape, which is strong enough to keep the screen from lifting. Replacing this tape is not a good idea because aftermarket tape is not nearly as strong as the one that came with the phone (unless you manage to get 3M VHB tape).
Once you stuck the screen assembly to the frame, be extra careful when putting everything back in place. The frame has tiny clips which need to be PERFECTLY aligned, otherwise... you'll know it when you get there haha. You can leave the frame in place without the screws, it'll be easier to open it again in case something goes wrong (you wont need to open the phone from the back to access the display)
I don't know why this happened. I'm using the tempered glass screen cover. Can anyone say what it this and what should I do?
http://i.hizliresim.com/NpqM9P.jpg
http://i.hizliresim.com/m3PvrV.jpg
Run some of the extra tools in AnTuTu to check if it's an actual screen problem.
Might be a "bubble" under the screen protector - can you "move" it with your finger when applying pressure?
Is it a spot where the screen is brighter? If so, I think it's a defect related to the backlight. I bought a cheap replacement screen for my Nexus 5 when I broke my original one and over time it's developed more and more bright areas. I suspect something is delaminating causing uneven backlighting. I believe it can also happen due to water/liquid damage, but in my case phone phone did not get wet.
Actually, I just tried twisting my phone and also applying pressure to the screen and noticed the LCD reacts (flashes) in those areas when I press hard, so I think it may be an issue with the LCD panel itself, not the backlight. In any case, I doubt there's much you can do about it, and be warned it could get worse (I used to have a spot or two near the bottom of my screen, but now I have them all over the screen.) In my case I've just learned to live with it, telling myself having paid $35 for a screen which developed this problem is a lot better than living with a cracked screen, and I'll have a new phone soon, but I would not expect this problem with a new phone.