First of all, this what I have and what I have and what has Happen:
Motorola razr GSM XT910
I have been running JB for a while via this method: http://forum.xda-developers.com/showthread.php?t=2078021
Today i flashed a new rom: http://forum.xda-developers.com/showthread.php?t=2213422
And it was awesome.
I made a Nandroid backup and then restored it after i did some thing on the phone. But then when i booted it, I just got to ther fastboot menu eveytime. I thought it was dead until I updated my Bootloader to A0.77: http://forum.xda-developers.com/showthread.php?t=1893347&page=3
Now, however, I don't have a clue on what to do. I have proably donwloaded over 5 different fastboot versions, both ICS and JB and tried to flash the phone with these. The process go well but it always ended up with a Black screen, and I have to ashut it down by holding the buttons.
Do anyone have any tips for me pn what I can do or is it truly bricked? I don't have any mone to buy a new phone right now, so I would have to use my old Sony Ericsson K810i
Next time, read the OP carefully, it says it must on the 982.124.14.XT910.Retail.en.AU JB OTA, the jelly bean you are running before is the verizon jelly bean, its not compatible, so you need to fastboot back to ics, the jelly bean fastboot you have downloaded is for verizon US only, theres no yet jelly bean fastboot for gsm, make sure you get to the AP Fastboot mode by going through the bootloader,
anyway, what are the errors showing on the screen?
TheMrcool212 said:
Next time, read the OP carefully, it says it must on the 982.124.14.XT910.Retail.en.AU JB OTA, the jelly bean you are running before is the verizon jelly bean, its not compatible, so you need to fastboot back to ics, the jelly bean fastboot you have downloaded is for verizon US only, theres no yet jelly bean fastboot for gsm, make sure you get to the AP Fastboot mode by going through the bootloader,
anyway, what are the errors showing on the screen?
Click to expand...
Click to collapse
I know I should, my bad, but done is done.
Before, I couldn't even use the bootloader, it just took me into fastboot mode directly and I got messages like: "Ivalid CC OTC/CC:webtop):Invalid sp data"
but after updating the fastboot loader to a0:77 I can now use the whole bootloader and I don't get this message. But I can still not use my old ICS fastboot files which i used for a month ago.
Do you know any ICS Fastboot files that would work?
I tried SPDREM_U_01.6.7.2-180_SPU-19-TA-11.2_SIGNEuropeAustraliaEMEA_USASPDRICSRTGB_HWp2b_Service1FF_fastboot.xml
But it didn't work.
I will try and fic the webtop, will update.
it seems that you have problem with the webtop partition, so you need to flash the gingerbread webtop (not installing gingerbread) .theres a tool that can flash the webtop_signed partition. you can download the files here
http://d-h.st/m8W
http://sbf.droid-developers.org/umt...USASPDRRTGB_HWp2b_Service1FF_fastboot.xml.zip
extract the Flash IT.rar and the fastboot xml.xip you've downloaded. also extract the ICS fastboot file and copy the webtop_signed file in the gingerbread fastboot folder to the ICS fastboot folder, and also copy all the files in the Flash IT folder and put it in the ICS folder
Now, enter to AP fastboot mode and connect it to your PC, in the ICS fastboot folder, run the FlashME.bat wait for it to flash
Okay, I'm gonna try that.
It finished without problems but I got these messages:
Invalid CG OTV(CC: cdrom): Invalid SP Data
Invalid CG OTV(CC: system): Invalid SO Data
Invalid CG version (CG: SYstem)
Invalid CG OTV (CG; system)
baxtex said:
Okay, I'm gonna try that.
It finished and I got these messages:
Invalid CG OTV(CC: cdrom): Invalid SP Data
Invalid CG OTV(CC: system): Invalid SO Data
Invalid CG version (CG: SYstem)
Invalid CG OTV (CG; system)
Click to expand...
Click to collapse
Flash the ics fastboot using rsd lite and factory reset in stock recovery
Sent from my GT-I9300 using xda app-developers app
TheMrcool212 said:
Flash the ics fastboot using rsd lite and factory reset in stock recovery
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
Tried that but the flashing process always fails after 2 seconds. Can't enter Recovery either.
baxtex said:
Tried that but the flashing process always fails after 2 seconds. Can't enter Recovery either.
Click to expand...
Click to collapse
make sure it says 'connected' in rsd lite. and also make sure you enter the AP Fastboot mode through the bootloader
Did as you said but it didn't make any difference. THough I have now tried al the fastboot files I curently have downloade, and one of them; p2b_spyder-umts_spyder-user-4.1.2-6.7.2_GC-384-402 actually made it to step 10 were it fails to flash "boot.img"
This was fastboot files for 4G version though.
baxtex said:
Did as you said but it didn't make any difference. THough I have now tried al the fastboot files I curently have downloade, and one of them; p2b_spyder-umts_spyder-user-4.1.2-6.7.2_GC-384-402 actually made it to step 10 were it fails to flash "boot.img"
This was fastboot files for 4G version though.
Click to expand...
Click to collapse
try to flash using this file
http://sbf.droid-developers.org/umt...SPDRICSRTGB_HWp2b_Service1FF_fastboot.xml.zip
i think it failed to flash 'boot.img' because you downloaded the wrong fastboot file, the 'boot.img' stands for the kernel
Nope, fails at the first step, "cdt.bin".
I think you have just update it to jelly bean, and you cant go back to ics since you have flashed the ROM. Now i understand why you got cdt.bin error. That means you cant go back to ICS
You can use this method
http://forum.xda-developers.com/showthread.php?t=2194825
But the problem is you can't root
Sent from my GT-I9300 using xda app-developers app
TheMrcool212 said:
I think you have just update it to jelly bean, and you cant go back to ics since you have flashed the ROM. Now i understand why you got cdt.bin error. That means you cant go back to ICS
You can use this method
http://forum.xda-developers.com/showthread.php?t=2194825
But the problem is you can't root
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
I tried this but i can still not enter Recovery. However, I now get some other error codes:
Invalid CG OTV (CG: System): Invalid SP Data
Invalid CG Version (CG: system)
Invalid CG OTV (CG: system)
However, looked at the cmd window now, and it fails at system write beacuse of low battery. I have opend the phone and I am now charging it, I'm gonna leave it for 2 hours and then try again.
Edit:
Got enough battery, but got the same results as above.
Related
hello! I was on ICS T-mobile and I tried to go to ICS Brasil.
I restored my mmcblk1p18 and cdrom after flash ICS Brasil and now I got error during reboot.
When I choose "Recovery" after AP fastboot, i
get the following errors.
Invalid CG OTV (CG: cdrom): Invalid SP Data
Invalid CG HAB (CG: cdrom), status: 0X0056)
Invalid CG OTV (CG: cdrom)
I tried to flash cdroms from diferents firmwares and nothing. I cant enter anymore to recovery, just AP fastboot.
I used RSD lite, moto-fastboot, everything and I just got that message "Invalid CG OTV....."
Please could you help me how to solve that problem?
you need to flash GB cdrom_signed from fastbootfiles, which is latam for you i guess
sevenup30 said:
you need to flash GB cdrom_signed from fastbootfiles, which is latam for you i guess
Click to expand...
Click to collapse
I already try that too... and keep with same error. it dont let me flash GB cdrom_signed.
And you are rigth, is a Latam. Sorry for my english...
Flash ebr_signed and mbr_signed from GB 2.3.6 and you'll be good.
Remember to renane the files .img and do
Code:
fastboot flash ebr ebr.img
Code:
fastboot flash mbr mbr.img
Sent from my XT910 using xda premium
pedrotorresfilho said:
Flash ebr_signed and mbr_signed from GB 2.3.6 and you'll be good.
Remember to renane the files .img and do
Code:
fastboot flash ebr ebr.img
Code:
fastboot flash mbr mbr.img
Sent from my XT910 using xda premium
Click to expand...
Click to collapse
Hi Pedro!!!
i'll try that when come back to my home. I already flashed that files, but with RSD lite and nothing.
I hope this time it works. Thanks a lot!
pedrotorresfilho said:
Flash ebr_signed and mbr_signed from GB 2.3.6 and you'll be good.
Remember to renane the files .img and do
Code:
fastboot flash ebr ebr.img
Code:
fastboot flash mbr mbr.img
Sent from my XT910 using xda premium
Click to expand...
Click to collapse
I made that and nothing changes :crying:
think my trouble is whith the cdrom. Cant flash it, if I could erased, but my fhone dont boot, cant enter in recovery, i dont know what to do!
when i tried to flash GB cdrom show this:
sending 'cdrom' (216832 KB)... OKAY [31.087s]
writing 'cdrom' ... INFOPreflash validation failure
FAILED (remote: )
rebooting....
:good:
Actually I could repair my phone. I just erased the cid partition using RSD lite.
i used T-mobile 2.3.6 file xml and put this
flash mbm allow-mbmloader-flashing-mbm.bin
Reboot-bootloader
Erase cid
And I was able to flash retail Brasil 2.3.6 and then apply OTA.
Thanks anyway and I hope this works for others with same problem with mmclk1p18 restaured and brick Razr.
Hello I inadvertently flashed his XT910 XML firmware 4.1.2 for XT912. The telephone does not work. I tried unbrick, but it does not work, does not start recovery. Runs only bootloader error "Invalid CG OTV".
Help restore the phone, please.
Thank you!
I am sorry for my bad English, I use Google Translate
UPD:
Through RSD Lite to flash now can only XT912 JB.
The phone turns on, but does not load launcher etc.
Other firmware via RSD not even installed. An error "failed flashing process 13/18 flash system".
I got that error too, try downloading the file again ut was a bad download or corrupted file...
Sent from my XT910 using xda premium
Steven87 said:
I got that error too, try downloading the file again ut was a bad download or corrupted file...
Sent from my XT910 using xda premium
Click to expand...
Click to collapse
Thanks for the reply! Unfortunately, this does not resolve the problem.
I think we should wait for the XML JB XT910.
I had the same problem, i switched from ICS to JB.vodafone and kept my root with Voodoo root keeper. One time my phone got into bootloop after restart (messed with build.prop a bit ).
Well i flashed a lot of stupid firmwares over RSD even x912 jellybean fastboot files on my x910 . But it just doesnt work
So a guy came to XDA forums and wrote this http://forum.xda-developers.com/showthread.php?t=2194825 I fallowed this instruction and got unbricked
I lost my Root, but i can atleast use my phone, which is more important :victory:
So there is one more side note to this tutorial
(as i flashed all sorts of files into my phone by trying to unbrick it, my partitions were a mess so)
So Before You use HDA-Pilot's instructions flash all partitions that you still have access to by hand.
Download EuroperRETAIL fastboot files that HDA gives you in his thread and flash with fastboot like this:
->fastboot flash recovery recovery.img
->fastboot flash cdrom cdrom_signed.img
...........
.....
...
Do this too all files and you will get error on system_signed and Boot.img, but your partitions will be ready to house euRetail JB and you will get System and Boot flashed on HSD-Pilot's tutorial, just before unbricking your doodles
TeddyOFLove said:
I had the same problem, i switched from ICS to JB.vodafone and kept my root with Voodoo root keeper. One time my phone got into bootloop after restart (messed with build.prop a bit ).
Well i flashed a lot of stupid firmwares over RSD even x912 jellybean fastboot files on my x910 . But it just doesnt work
So a guy came to XDA forums and wrote this http://forum.xda-developers.com/showthread.php?t=2194825 I fallowed this instruction and got unbricked
I lost my Root, but i can atleast use my phone, which is more important :victory:
So there is one more side note to this tutorial
(as i flashed all sorts of files into my phone by trying to unbrick it, my partitions were a mess so)
So Before You use HDA-Pilot's instructions flash all partitions that you still have access to by hand.
Download EuroperRETAIL fastboot files that HDA gives you in his thread and flash with fastboot like this:
->fastboot flash recovery recovery.img
->fastboot flash cdrom cdrom_signed.img
...........
.....
...
Do this too all files and you will get error on system_signed and Boot.img, but your partitions will be ready to house euRetail JB and you will get System and Boot flashed on HSD-Pilot's tutorial, just before unbricking your doodles
Click to expand...
Click to collapse
Thank you very much for your reply!
Unfortunately, nothing happened. Maybe we did something wrong, I do not know.
superdeman said:
Thank you very much for your reply!
Unfortunately, nothing happened. Maybe we did something wrong, I do not know.
Click to expand...
Click to collapse
What region are you from?
Is it XT910 you are using?
Did you try to fallow HSD guide and flash FF manually before hand? If so then what happened what is the issue after doing so|?
TeddyOFLove said:
What region are you from?
Is it XT910 you are using?
Did you try to fallow HSD guide and flash FF manually before hand? If so then what happened what is the issue after doing so|?
Click to expand...
Click to collapse
Device regoin EMEA. I'm from Belarus.
Yes, i use XT910.
Tried to do the instructions, but after that nothing changes. Loaded only bootloader with an error partition system.
If you is not difficult, please write how you restore your phone, step by step with links.
I would be very grateful!
superdeman said:
Device regoin EMEA. I'm from Belarus.
Yes, i use XT910.
Tried to do the instructions, but after that nothing changes. Loaded only bootloader with an error partition system.
If you is not difficult, please write how you restore your phone, step by step with links.
I would be very grateful!
Click to expand...
Click to collapse
I will try. But remember this is all HSD-Pilots work, i only try to make it clear to you.
1) download These fastboot files.rar (clink on text)
2)download retailEU. jellybean OTA
3)Download HSD-pilots UNBRICK.rar
4)UNRAR HSD-pilots UNBRICK.rar from step (3) to any new folder (lets name it UNBRICK)
5) UNRAR Fastboot files:
cdrom_signed
cdt.bin_signed
devtree_signed
ebr_signed
mbr_signed
recovery_signed
radio.img
system_signed
from step (1) to Folder from step (4) we named UNBRICK ONLY extract files i said
6)Connect your device to pc
7)open UNBRICK folder Hold shift and right click on white space -> then press OPEN COMMAND WINDOW HERE
8)flash files from step (5) by writing in the command window you opened:
mfastboot flash cdrom cdrom_signed
mfastboot flash cdt.bin cdt.bin_signed
mfastboot flash devtree devtree_signed
mfastboot flash ebr ebr_signed
mfastboot flash mbr mbr_signed
mfastboot flash recovery recovery_signed
mfastboot flash radio radio.img
9)with the phone still connected to PC open UNBRICK folder and tun Unbrick.bat.
10) after unbrick.rar flashed press power button once, and immediately hold volume up + volume down and press power again
11) go down to recovery and press volume up
12) when you just follow instructions in bat file. see android picture press volume down and volume up at the same time and wait for radio to install
13) after installation of radio wipe data and catch -> navigate to factory reset and do it
14) Then go to install update from external memory and install retailEU. jellybean OTA that you downloaded (you have to put it to your external SD card)
15) If all is fine it will update, just reboot and its unbricked
TeddyOFLove said:
I will try. But remember this is all HSD-Pilots work, i only try to make it clear to you.
1) download These fastboot files.rar (clink on text)
2)download retailEU. jellybean OTA
3)Download HSD-pilots UNBRICK.rar
4)UNRAR HSD-pilots UNBRICK.rar from step (3) to any new folder (lets name it UNBRICK)
5) UNRAR Fastboot files:
cdrom_signed
cdt.bin_signed
devtree_signed
ebr_signed
mbr_signed
recovery_signed
radio.img
system_signed
from step (1) to Folder from step (4) we named UNBRICK ONLY extract files i said
6)Connect your device to pc
7)open UNBRICK folder Hold shift and right click on white space -> then press OPEN COMMAND WINDOW HERE
8)flash files from step (5) by writing in the command window you opened:
mfastboot flash cdrom cdrom_signed
mfastboot flash cdt.bin cdt.bin_signed
mfastboot flash devtree devtree_signed
mfastboot flash ebr ebr_signed
mfastboot flash mbr mbr_signed
mfastboot flash recovery recovery_signed
mfastboot flash radio radio.img
9)with the phone still connected to PC open UNBRICK folder and tun Unbrick.bat.
10) after unbrick.rar flashed press power button once, and immediately hold volume up + volume down and press power again
11) go down to recovery and press volume up
12) when you just follow instructions in bat file. see android picture press volume down and volume up at the same time and wait for radio to install
13) after installation of radio wipe data and catch -> navigate to factory reset and do it
14) Then go to install update from external memory and install retailEU. jellybean OTA that you downloaded (you have to put it to your external SD card)
15) If all is fine it will update, just reboot and its unbricked
Click to expand...
Click to collapse
Thank you! Excellent manual! It's simple and clear.
But, unfortunately:
Code:
mfastboot flash cdt.bin cdt.bin_signed
sending 'cdt.bin' (16 KB)... OKAY [ 0.000s]
writing 'cdt.bin'... INFOPreflash validation failure
FAILED (remote: )
superdeman said:
Thank you! Excellent manual! It's simple and clear.
But, unfortunately:
Code:
mfastboot flash cdt.bin cdt.bin_signed
sending 'cdt.bin' (16 KB)... OKAY [ 0.000s]
writing 'cdt.bin'... INFOPreflash validation failure
FAILED (remote: )
Click to expand...
Click to collapse
Just ignore it
it doesnt matter as long as you fallow all at steps. the end should be unbricked, and it was bad tutorial just didnt have much time to make it easier to read.
i think cdt.bin was supposed to fail others will not, i just didnt remember the details as i did it week ago
So as i said just do it from start and copy all errors you get, as it may just be something i overlooked and it will still unbrick your phone hopefully, other wise we get more data on what might be wrong. Actually if you would agree on live session on team-viewer so i can control your pc and do it for you it would be ok too .
hi, i have an european gsm xt910 with deleted CID and verizion us jb (http://forum.xda-developers.com/showthread.php?t=2182674).
i've been using it for a couple of weeks with no problem, but today, after i turned off the phone, each time i try to turn it on it appears a black screen with the following white things (like the fastboot mode):
AP Fastboot Flash Mode (S) (Boot Failure)
0A.6c
To return to normal mode - first press power key to power down
Device is LOCKED. Status code: 0
Battery OK
OKto Program
Connect USB
Data Cable
Invalid CG OTV (CG: webtop): Invalid SP Data
Invalid CG HAV (CG: wbtop, status: 0X004E)
Invalid CG OTV (CG: webtop)
Click to expand...
Click to collapse
is it bricked? do i have to follow HDA-Pilot's instructions or is it something different since i deleted my CID (although i have a backup, i can't recover it because i can't boot into recovery)?
if there's another way to recover my phone with keeping root would be great, but of course it's better to have a working phone without root than a rooted brick
this evening i'm leaving for the whole weekend, so it would be awesome if you could answer me asap, so i can (hopefully!) fix my phone before departing. TY!
AW: Bricked XT910
http://forum.xda-developers.com/showthread.php?p=38189529
Gesendet von meinem XT890 mit Tapatalk 2
HSD-Pilot said:
http://forum.xda-developers.com/showthread.php?p=38189529
Gesendet von meinem XT890 mit Tapatalk 2
Click to expand...
Click to collapse
thanks a lot man!! i solved it by simply running the whirleyes's razr_bl_mbm_*.zip you linked me to.
Me too! jeje
ok, i got a new message similar to the previous one. this is the situation:
i have an italian gsm xt910 with deleted CID and verizion us jb (http://forum.xda-developers.com/show....php?t=2182674) and i tried to install the CM10.1 xt910 version. i use BMM.
- during boot i went to BMM and restored CID
- wiped everything
- installed the lastest CM10.1 nightly (0430) + gapps
and after i booted the phone it appeared the following message:
AP Fastboot Flash Mode (S) (Boot Failure)
0A.77
eMMC Info: Size 16G
To return to normal mode - first press power key to power down
Device is LOCKED. Status code: 0
Battery OK
OKto Program
Connect USB
Data Cable
Invalid CG HAB (CG: boot, status: 0X0056)
Click to expand...
Click to collapse
and i can't go to recovery anymore, since this message appears ASAP the phone starts. what happened? how can i fix this? ty in advance.
i found this thread (http://forum.xda-developers.com/showthread.php?t=2194825), but i'd rather not lose root + recover it using linux (never used linux), if it is possibile. is it enought to go here and install the retail UK firmware using RSD lite?
edit: ok i used rsd lite 6.15 + the UK JB firmware. now i'm fighting (using this thread) to gain my root rights back
Hello on the weekend that just passed my GSM RAZR's battery completely died and when I went to plug it in in the morning I was greeted with a black screen that reads:
AP Fastboot Flash Mode (S) (Boot Failure)
0A.6C
To return to normal mode - first press power key to power down
Device is LOCKED. Status Code: 0
Battery Low
Cannot Program
Connect USB
Data Cable
Invalid CG OTV (CG: webtop): Invalid SP Data
Invalid CG HAB (CG: webtop, status 0X004E)
Invalid CG OTV (CG: webtop)
I am on the cyanogenmod JB 4.2.2 and it was working fine without any issue really. I also don't think my phone is charging because it will only turn on if I plug it into and outlet. If I plug it in my computer to attempt to use RSD I just get the white light in the notification light.
So I was wondering if anyone could be of any help because this is my main phone and I am out of communication for the time being until it gets fixed.
EDIT: Forgot to mention that I can get into stock recovery by holding the volume +/- down and plugging it into a wall charger but any option I select brings me back to a similar screen, sometimes missing the errors the other screen had at the bottom.
Çözümü için herhangi bir XT910 yada XT912 (cihazına göre) Gingerbread temelli bir rom'un içerisinden webtop_signed.img dosyasını çıkarın ve aşağıdaki komutla flashlayın.
fastboot flash webtop webtop_signed.img
http://motomodtr.forumcommunity.net/?t=53855516
same issue
I have same problem. Please help. I don't know how to use command "fastboot flash webtop webtop_signed.img"... Where type this command?
I am on Jellybean 4.2.2, not Ginergread. Anyone else with any help? And I plugged the phone in all night last night and now it can show the menu without being on charge.
[/COLOR]
RideR10 said:
I have same problem. Please help. I don't know how to use command "fastboot flash webtop webtop_signed.img"... Where type this command?
Click to expand...
Click to collapse
flash it in using the fastboot folder, just search for the file. put the webtop file in the folder, open the command window on the folder and run the command
TheMrcool212 said:
[/COLOR]
flash it in using the fastboot folder, just search for the file. put the webtop file in the folder, open the command window on the folder and run the command
Click to expand...
Click to collapse
If it help I describe my RAZR...
I have made dual boot with boot menu manager on my razr: 1. system is stock JB 4.1.2
2.system is AOKP 4.2.2
Everything works fine until I changed bootanimation on 2. system. After reboot phone reports this issue
I download ICS 4.0.4 file, but this fastboot file doesn't contain file "webtop_signed". After that I download Gingerbread fastboot file, where I found file "webtop_signed". Will this gingerbread "webtop_signed" work with JB ?
Where can i download that "fastboot folder"?
In advance thank for your help and sorry for my ENG
http://dl.projectlense.com/download.php?file=spyder/razr_bl_mbm_0a77.zip
Download and extract this. Connect in AP and run the bat.
Gesendet von meinem XT890 mit Tapatalk 2
---------- Post added at 07:23 PM ---------- Previous post was at 07:13 PM ----------
BTW: Everyone that uses BMM and still got the 0A.6... Bootloader should update it by using the linked file, to prevent those Webtop Issues!
Gesendet von meinem XT890 mit Tapatalk 2
Thank you for your help. :good: I spent nearly two days searching for solution.
thanks alot
i had the same problem and almost threw it out the window
now fixed :good:
Help Please
Hey i have the same problem where it say " AP fastboot flash mode (S) (boot failure)" I ran the windows bat file and it restarted the bootloader but the same problem still showed. Anybody have any ideas as to what im doing wrong or what else i can do? thanks
HSD-Pilot said:
dl. projectlense. com/download.php?file=spyder/razr_bl_mbm_0a77.zip
Download and extract this. Connect in AP and run the bat.
Click to expand...
Click to collapse
Are you sure that download link not expired? The website is no more available. Any new link from anyone?
I have the same problem, after flashing Magisk 15.3 form RR Nougat OS.
What should I do?
I'v got Droid RAZER Utility 1.8 and tried to roll back to stock ICS via Fastboot but it didn't fix it, where is 'devtree' error in log.
My next attempt was to flash it with RDS Lite but it doen's work under Windows 10, to now I'm trying to manually flash firmware from RAZR XT910 Firmwares SuperThread (Jelly Bean) with Droid utility moto-fastboot.exe command.
For 9.8.2O-124_SPUEM-14_S7_USASPDRICS01RUKE1007.0R_USASPDRJBRTGB_P011_b57374ab5a_p2b_S1FF_fb_CFC.xml.zip firmware it will be:
Code:
moto-fastboot flash mbm allow-mbmloader-flashing-mbm.bin
moto-fastboot reboot-bootloader
moto-fastboot flash mbmloader mbmloader.bin
moto-fastboot flash mbm mbm.bin
moto-fastboot reboot-bootloader
moto-fastboot flash cdt.bin cdt.bin_signed
moto-fastboot erase cache
moto-fastboot erase userdata
moto-fastboot erase emstorage
moto-fastboot flash logo.bin logo.bin
moto-fastboot flash ebr ebr_signed
moto-fastboot flash mbr mbr_signed
moto-fastboot flash devtree devtree_signed
moto-fastboot flash system system_signed
moto-fastboot flash boot boot_signed
moto-fastboot flash recovery recovery_signed
moto-fastboot flash cdrom cdrom_signed
moto-fastboot flash emstorage emstorage.img
moto-fastboot flash radio radio.img
But I keep getting battery low warning:
Code:
moto-fastboot flash mbmloader mbmloader.bin
sending 'mbmloader' (42 KB)... FAILED (remote: Battery Low)
How to charge MOTO if I can't get to system and recovery, I'm not sure if it's charging on fastboot screen.
vkmaxx said:
My next attempt was to flash it with RDS Lite but it doen's work under Windows 10, to now I'm trying to manually flash firmware from RAZR XT910 Firmwares SuperThread (Jelly Bean) with Droid utility moto-fastboot.exe command.
For 9.8.2O-124_SPUEM-14_S7_USASPDRICS01RUKE1007.0R_USASPDRJBRTGB_P011_b57374ab5a_p2b_S1FF_fb_CFC.xml.zip firmware it will be:
But I keep getting battery low warning:
How to charge MOTO if I can't get to system and recovery, I'm not sure if it's charging on fastboot screen.
Click to expand...
Click to collapse
Buy or make the factory cable...
https://forum.xda-developers.com/showthread.php?t=1077414
I was able to flash my phone with moto-fastboot.exe by NOT executing "moto-fastboot reboot-bootloader". This was the moment when after reboot phone was showing "low battery" warrning. After taking it from charger and not rebooting I was able to flash it.
Then Jelly Bean -> root -> SafeStrap - > LineageOS
Hello,
After stuck flash to ICS, i decide to flash using JB files from sbf.droid-developers.org/umts_spuder/list.php
I used O2 JB and tried "Unknown Carrier" and "Retail British" also.
My XT910 get bit progress now. This device can turn on stable without any self reboot.
But again I can't boot to BP Tool
Now I only able boot to BP HW Diag.
Kindly help me to fix this issue.
idwijayaku said:
Hello,
After stuck flash to ICS, i decide to flash using JB files from sbf.droid-developers.org/umts_spuder/list.php
I used O2 JB and tried "Unknown Carrier" and "Retail British" also.
My XT910 get bit progress now. This device can turn on stable without any self reboot.
But again I can't boot to BP Tool
Now I only able boot to BP HW Diag.
Kindly help me to fix this issue.
Click to expand...
Click to collapse
Install the Boot Menu Manager in playstore. The recovery allows you to boot without BP Tools and BP HW Diag
TheMrcool212 said:
Install the Boot Menu Manager in playstore. The recovery allows you to boot without BP Tools and BP HW Diag
Click to expand...
Click to collapse
I have to root my device first.
But I'm not sure root for XT910 JB is available now.
anyone?
Turn off your phone, remove the sim card and reboot. Then, power off your phone again and insert sim card and reboot.
TheMrcool212 said:
Turn off your phone, remove the sim card and reboot. Then, power off your phone again and insert sim card and reboot.
Click to expand...
Click to collapse
OMG.... you saved my phone.. thanks a lot !!
It works, I can boot in BP Tools now..
Next step is how can I restore my cid and change my baseband without root?
Because upgrade to JB makes my baseband doesn't work in my region.
Also I found usb debugging notification on my phone, but it's not connected in pc.
idwijayaku said:
OMG.... you saved my phone.. thanks a lot !!
It works, I can boot in BP Tools now..
Next step is how can I restore my cid and change my baseband without root?
Because upgrade to JB makes my baseband doesn't work in my region.
Also I found usb debugging notification on my phone, but it's not connected in pc.
Click to expand...
Click to collapse
There are two methods to restore cid. One of the methods need root and other not needed. Since you have no root, download the file ( here ) in your PC. Then extract the file. make sure those files are in a folder. Put your cid.img file into the extracted file. Hold Shift + left click and select "open the command window here".
Turn off your phone. Go to the bootloader (like one you boot to bptools) but this time select the 'AP Fastboot mode' . Connect your phone to your PC. In the terminal, run this line:
Code:
fastboot flash cid cid.img
Make sure no errors when flashing it. And reboot
TheMrcool212 said:
There are two methods to restore cid. One of the methods need root and other not needed. Since you have no root, download the file ( here ) in your PC. Then extract the file. make sure those files are in a folder. Put your cid.img file into the extracted file. Hold Shift + left click and select "open the command window here".
Turn off your phone. Go to the bootloader (like one you boot to bptools) but this time select the 'AP Fastboot mode' . Connect your phone to your PC. In the terminal, run this line:
Code:
fastboot flash cid cid.img
Make sure no errors when flashing it. And reboot
Click to expand...
Click to collapse
Thank you for file
- so i download the file and use file for windows
- i start the command prompt and I got this error:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
is there some steps that i missed?
and, after yesterday i sucessfully boot to BP Tool, today I can't boot on that mode again, although i did same like before
- power off phone in BP HW Diag
- take out the sim card
- boot again in BP HW Diag
- power off the phone again
- insert simcard
- boot in BP Tool
- now it's just stuck in O2 logo.
Please help me again
Never seen that problem before, but it worked for me. Try to follow these instructions.
1. Download the file ( Here! )
2. Extract the file. You will see a file named allow-mbmloader-flashing-mbm
3. Put the .bin file in the fastboot folder.
4. Put your phone in AP Fastboot mode, connect it to PC
5. Run these commands
Code:
fastboot flash mbm allow-mbmloader-flashing-mbm.bin
fastboot reboot-bootloader
fastboot flash cid cid.img
All thanks to the therazrguy
TheMrcool212 said:
Never seen that problem before, but it worked for me. Try to follow these instructions.
1. Download the file ( Here! )
2. Extract the file. You will see a file named allow-mbmloader-flashing-mbm
3. Put the .bin file in the fastboot folder.
4. Put your phone in AP Fastboot mode, connect it to PC
5. Run these commands
Code:
fastboot flash mbm allow-mbmloader-flashing-mbm.bin
fastboot reboot-bootloader
fastboot flash cid cid.img
All thanks to the therazrguy
Click to expand...
Click to collapse
Thank you again..
Those command line executed very well.
Suspend screen is not appear again.
But i got another error
Invalid CG OTV (CG: cdrom): Invalid SP Data
Invalid CG HAB (CG:cdrom, status: 0X0056)
Invalid CG OTV (CG: cdrom)
Please help me how to get my phone back..
idwijayaku said:
Thank you again..
Those command line executed very well.
Suspend screen is not appear again.
But i got another error
Invalid CG OTV (CG: cdrom): Invalid SP Data
Invalid CG HAB (CG:cdrom, status: 0X0056)
Invalid CG OTV (CG: cdrom)
Please help me how to get my phone back..
Click to expand...
Click to collapse
Try to flash the jelly bean fastboot file on RSD Lite. I think the European jelly bean fastboot files are out. But i am not sure.
Sent from my GT-I9300 using xda app-developers app
I flashed with O2 and Retail UK, but this error still exist.
I just erase cid using your command, so I can get back to BP HW Diag again, still can't boot to BP Tools.
idwijayaku said:
I flashed with O2 and Retail UK, but this error still exist.
I just erase cid using your command, so I can get back to BP HW Diag again, still can't boot to BP Tools.
Click to expand...
Click to collapse
You had just erased cid? did i just told you how to restore cid?
But anyway, after few minutes of searching, i have found someone posted how to flash the cdrom partition. It is by TeddyOFLove
I will try. But remember this is all HSD-Pilots work, i only try to make it clear to you.
1) download These fastboot files.rar (clink on text)
2)download retailEU. jellybean OTA
3)Download HSD-pilots UNBRICK.rar
4)UNRAR HSD-pilots UNBRICK.rar from step (3) to any new folder (lets name it UNBRICK)
5) UNRAR Fastboot files:
cdrom_signed
cdt.bin_signed
devtree_signed
ebr_signed
mbr_signed
recovery_signed
radio.img
system_signed
from step (1) to Folder from step (4) we named UNBRICK ONLY extract files i said
6)Connect your device to pc
7)open UNBRICK folder Hold shift and right click on white space -> then press OPEN COMMAND WINDOW HERE
8)flash files from step (5) by writing in the command window you opened:
mfastboot flash cdrom cdrom_signed
mfastboot flash devtree devtree_signed
mfastboot flash ebr ebr_signed
mfastboot flash mbr mbr_signed
mfastboot flash recovery recovery_signed
mfastboot flash radio radio.img
9)with the phone still connected to PC open UNBRICK folder and tun Unbrick.bat.
10) after unbrick.rar flashed press power button once, and immediately hold volume up + volume down and press power again
11) go down to recovery and press volume up
12) when you just follow instructions in bat file. see android picture press volume down and volume up at the same time and wait for radio to install
13) after installation of radio wipe data and catch -> navigate to factory reset and do it
14) Then go to install update from external memory and install retailEU. jellybean OTA that you downloaded (you have to put it to your external SD card)
15) If all is fine it will update, just reboot and its unbricked
Click to expand...
Click to collapse
Also, i forgot that HSD-Pilot posted a thread how to unbrick on the jelly bean OTA, use this thread if its doesnt work.
thanks again for another how to.
i'm downloading the files now there are two question:
1. TeddyOfLove require fastboot files on ICS I guess SPDREM_UMTS_01.6.7.xxx but why tutorial from HSD-Pilot doesn't require this file? which one should i follow
2. Based on above tutorial there are no CID restore? so when I restore it? after all works or before all steps start?
idwijayaku said:
thanks again for another how to.
i'm downloading the files now there are two question:
1. TeddyOfLove require fastboot files on ICS I guess SPDREM_UMTS_01.6.7.xxx but why tutorial from HSD-Pilot doesn't require this file? which one should i follow
2. Based on above tutorial there are no CID restore? so when I restore it? after all works or before all steps start?
Click to expand...
Click to collapse
1. I think you have to use HSD-Pilot's thread. If its doesnt work, use TeddyOfLove's post. Yes, download the fastboot files if you follow TeddyOfLove's post.
2. Use my tutorial how to restore it.
Sent from my GT-I9300 using xda app-developers app
I tried HSD-Pilot's step but stuck after update from external storage.
During "updating BP..." process I got this error
asserted failed: motoflash ("/tmp/bp.img")
now I will try teddyoflove step
I will update you asap.
TheMrcool212 said:
You had just erased cid? did i just told you how to restore cid?
.
Click to expand...
Click to collapse
I just wrote this part.
I have to erase my cid again, coz i can't go to any boot.
Screen just stuck on that error.
TheMrcool212 said:
1. I think you have to use HSD-Pilot's thread. If its doesnt work, use TeddyOfLove's post. Yes, download the fastboot files if you follow TeddyOfLove's post.
2. Use my tutorial how to restore it. Restore it after
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
I've done tried with HSD-Pilot but stuck on updating BP process,
then I tried TeddyOfLove's post also:
still stuck on updating bp.. process:
I guess this is why I can't go to BP Tools
Did you restore the cid and flash the OTA?
Sent from my GT-N7100 using xda app-developers app
TheMrcool212 said:
Did you restore the cid and flash the OTA?
Sent from my GT-N7100 using xda app-developers app
Click to expand...
Click to collapse
As you said earlier, I must flash the OTA first then restore the cid.
This error appears during flashing the OTA
I was trying to put eclipse rom on my wife's XT 910, so I backed up the kernel and CID with BMM, flashed the kernel, erased CID, then flashed the rom and patch. when i rebooted i tried to boot through BP tools and I get the dead CID error. I cant boot the phone past AP fastboot, please someone help before my wife's patience runs out...
jessel0001 said:
I was trying to put eclipse rom on my wife's XT 910, so I backed up the kernel and CID with BMM, flashed the kernel, erased CID, then flashed the rom and patch. when i rebooted i tried to boot through BP tools and I get the dead CID error. I cant boot the phone past AP fastboot, please someone help before my wife's patience runs out...
Click to expand...
Click to collapse
Try to restore CID.
TunneIVision said:
Try to restore CID.
Click to expand...
Click to collapse
i restored cid and eu kernel, no i get boot failure with all boot options and my bootloader reads
0A.6c.
Invalid CG OTV (CG webtop): invalid so data)
invalid CG HAB (CG: webtop, status: 0x004e)
invalid CG OTV (CG:webtop)
jessel0001 said:
i restored cid and eu kernel, no i get boot failure with all boot options and my bootloader reads
0A.6c.
Invalid CG OTV (CG webtop): invalid so data)
invalid CG HAB (CG: webtop, status: 0x004e)
invalid CG OTV (CG:webtop)
Click to expand...
Click to collapse
Try to install your previous rom.
TunneIVision said:
Try to install your previous rom.
Click to expand...
Click to collapse
I still can't access any recoveries, I think I'm going to have to RSD back to stock when i can download the SBF.
I'm going to try to flash a fresh webtop first
After I restored the cid and kernel I just had to upgrade the boot loader.
Sent from my DROID RAZR using xda app-developers app