Hi Guys,
I really need your help.
After tried upgarde to LIQUIDSMOOTH JB, i found that my baseband doesn't work in my country (i'm in Indonesia).
I tried to updated my baseband with BMM but not work.
So i decide to do fastboot from ICS then upgrade to Liquidsmooth in proper way.
What I did:
- backup CID
- erase CID
- get ICS fastboot file asia retail
- ap fastboot with rsd
- after reboot manual and go to BP Tool
- my phone entering the system but then it back to screen moto again
- since i used verizon phone, i tried to fasboot with EU fastboot ICS file
- ap fastboot with rsd
- manual reboot and go to bp tool
- screen shows, updating system, starting system but then it throw me back to screen moto again
now my battery is low, and i'm waiting for desktop charger
what i need to do to get my phone back?
after rsd done flash my phone, i got message in status "Please manually power up this phone"
what i did then:
- unplug phone from usb cable,
- reboot phone (volume up + down, power, after led flashing, i release all buttons)
- then i press again volume up + down, power , after led flashing, i keep pushing volume up + down untill ap fastboot menus appears
- i plug again usb and waiting until result in rsd shows PASS
Am i did the right steps?
Thank you in advance for your suggestions
same problem with me
idwijayaku said:
Hi Guys,
I really need your help.
After tried upgarde to LIQUIDSMOOTH JB, i found that my baseband doesn't work in my country (i'm in Indonesia).
I tried to updated my baseband with BMM but not work.
So i decide to do fastboot from ICS then upgrade to Liquidsmooth in proper way.
What I did:
- backup CID
- erase CID
- get ICS fastboot file asia retail
- ap fastboot with rsd
- after reboot manual and go to BP Tool
- my phone entering the system but then it back to screen moto again
- since i used verizon phone, i tried to fasboot with EU fastboot ICS file
- ap fastboot with rsd
- manual reboot and go to bp tool
- screen shows, updating system, starting system but then it throw me back to screen moto again
now my battery is low, and i'm waiting for desktop charger
what i need to do to get my phone back?
after rsd done flash my phone, i got message in status "Please manually power up this phone"
what i did then:
- unplug phone from usb cable,
- reboot phone (volume up + down, power, after led flashing, i release all buttons)
- then i press again volume up + down, power , after led flashing, i keep pushing volume up + down untill ap fastboot menus appears
- i plug again usb and waiting until result in rsd shows PASS
Am i did the right steps?
Thank you in advance for your suggestions
Click to expand...
Click to collapse
same problem with me :crying:
have you find the solution ?
(uda ktmu solusinya bos ? klo uda mohon share ya...)
What is your battery status????
Sent from my LT28h using xda premium
alwaysdksh said:
What is your battery status????
Sent from my LT28h using xda premium
Click to expand...
Click to collapse
During flashing i charge until more than 90%
Now I can only go to BP HW Diag, but cannot go to system with BP Tools
What should I do?
alihabibie said:
same problem with me :crying:
have you find the solution ?
(uda ktmu solusinya bos ? klo uda mohon share ya...)
Click to expand...
Click to collapse
(hehehe pasti dikabarin kalo udah solve bos)
Related
I have a strange situation with my Razr XT910, let me explain to you guys and please tell me what to do:
1- My Razr was on 2.3.6
2- I rooted it, but I cannot remember which method as I tried many ways and cannot really remember which one succeeded.
3- After rooting I flashed a 4.0.4 AOKP-GSM-J.Y.Daddy rom
4- I have several issues with the rom so I want to install another rom, so I tried Eternity project rom. It didn't work and gives me message "Installation aborted", so I gave up.
5- Decided to go back to stock rom, so downloaded the right SBF and RSD lite.
6- I put the USB debugging on
7- I turned my phone off and go to boot loader mod by holding Volume +/- and power buttons and go to SBF flash, connect the USB cable and hear the notification sound from my laptop. No message received from the PC saying installing device. Receive message from RSD USB connected and one clicked show device it gives everything N/A
8- Uncompressed the SBF and pressed start. Then process FAIL
9- Now, tried to turn the phone on, I have to go to to Fastboot mode and press power long then screen goes off. Then I press volume +/- with power again to go to bootloader mode then choose normal reboot to turn my phone back.
10- Tried the above steps over than 30 times for 2 days. Suddenly I discovered that my phone is unrooted when I tried to install any app requires rooting such as Titanium.
My ICS works fine with some bugs, I still wants to go back.
Can any one help me, I explained everything I'm going through.
Appreciated.
flupo2000 said:
I have a strange situation with my Razr XT910, let me explain to you guys and please tell me what to do:
1- My Razr was on 2.3.6
2- I rooted it, but I cannot remember which method as I tried many ways and cannot really remember which one succeeded.
3- After rooting I flashed a 4.0.4 AOKP-GSM-J.Y.Daddy rom
4- I have several issues with the rom so I want to install another rom, so I tried Eternity project rom. It didn't work and gives me message "Installation aborted", so I gave up.
5- Decided to go back to stock rom, so downloaded the right SBF and RSD lite.
6- I put the USB debugging on
7- I turned my phone off and go to boot loader mod by holding Volume +/- and power buttons and go to SBF flash, connect the USB cable and hear the notification sound from my laptop. No message received from the PC saying installing device. Receive message from RSD USB connected and one clicked show device it gives everything N/A
8- Uncompressed the SBF and pressed start. Then process FAIL
9- Now, tried to turn the phone on, I have to go to to Fastboot mode and press power long then screen goes off. Then I press volume +/- with power again to go to bootloader mode then choose normal reboot to turn my phone back.
10- Tried the above steps over than 30 times for 2 days. Suddenly I discovered that my phone is unrooted when I tried to install any app requires rooting such as Titanium.
My ICS works fine with some bugs, I still wants to go back.
Can any one help me, I explained everything I'm going through.
Appreciated.
Click to expand...
Click to collapse
Unplug razr from pc
Uninstall all razr software
Reinstall motocast 1.29
Plug razr, let drivers reinstall
Turn it of
Go into fastboot menu
Wait drivers reinstall
Flash .sbf
Cheers
Sent from my XT910 using Tapatalk 2
Thanks dear, that's exactly what I did 30 times and I keep getting same message on RSD "FAIL"
Now I tried this http://forum.xda-developers.com/showthread.php?t=1486718
and choose # 1 restore EU GSM and I was stuck in a boot loading loop.
Any time I try an option with my phone I go to this screen:
AP Fastboot Flash Mode (s) (Flash Failure)
OA.GC
To return to normal mode-first press power key to power down
Device is LOCKED. Status Code:0
Battery OK
OK to Program
Connect USB
Data Cable
flupo2000 said:
Thanks dear, that's exactly what I did 30 times and I keep getting same message on RSD "FAIL"
Now I tried this http://forum.xda-developers.com/showthread.php?t=1486718
and choose # 1 restore EU GSM and I was stuck in a boot loading loop.
Any time I try an option with my phone I go to this screen:
AP Fastboot Flash Mode (s) (Flash Failure)
OA.GC
To return to normal mode-first press power key to power down
Device is LOCKED. Status Code:0
Battery OK
OK to Program
Connect USB
Data Cable
Click to expand...
Click to collapse
Try this
http://forum.xda-developers.com/showthread.php?t=1453660
Sent from my XT910 using Tapatalk 2
pedrotorresfilho said:
Try this
http://forum.xda-developers.com/showthread.php?t=1453660
Sent from my XT910 using Tapatalk 2
Click to expand...
Click to collapse
Thanks again,
I forced it to close then it was booted to a screen (not CWmod) which enabled me to wipe the data and restore factory sittings and it worked. Now the phone like brand new and I installed the update to 2.3.6
hello, i brick my phone when i install the new ota ics latam..
what i can do?
thanks
this ota leak.. http://forum.xda-developers.com/showthread.php?t=1688241
What happens when you PWR + Volume Up + Volume Down?
If you could explain a little bit more on what you were doing by the time it bricked, it could help someone figure it out...
Now, what happens when you power it up, holding volumes up and down? Does the boot menu comes up?
Cheers
I have the same problem.
I tryed to flash an Latam ICS after install an 2.3.6. My phone started enter in fc or spend a lot of time on moto logo. Now. It just stay on boot logo. RDS jus flash until step 5 (it recognize my phone, but didnt finish to flash). I can enter in fastboot mode, but this message appear:
ap fast boot flash mode (s)
0a.6c
to return to normal mode - first press power key to power dowm
device is locked. status code 0:
batter ok
ok to program
transfer mode
usb conected.
Somebody can help me please.
Tks
Search on "unblick 4.0.4 tutorial motorola razr" in google.
I hope this help you. good luck!
Hi guys
My XT910 was submerged in a river a couple of weeks ago. It did not short circuit, but I think it got soft bricked.
Whenever it boots, it will display AP Fastboot Flash Mode (S).
I can boot to Boot Mode Selection Menu with Power + Vol+ + Vol-, but I cannot scroll or select anything. I usually enter the page so that I can access BMM to Power Off the device or access the internal storage.
I tried to Fastboot an Asia ROM but the process got stuck at Step 2. I had no choice but to unplug USB. From then on, my laptop could never detect my phone again. I am using the latest Motorola Drivers and cable.
Today, I tried what was suggested here:
http://forum.xda-developers.com/showthread.php?t=1738769
but because my phone could not be detected by my laptop, I transferred the Boot_new.img to MicroSD and used BMM to flash new kernel. (I wasn’t sure what I was doing.)
Now, when I boot my phone, AP Fastboot Flash Mode (S), and what I get after Boot Mode Selection Menu is a brief Motorola logo and Invalid Flash Mode (S) (Boot Failure).
As of last check (half hour ago), battery health was at 96%. I cannot power down the device without BMM, or at least I don’t know how to. Can anyone assist me on restoring my phone to a functional state again?
Edit: prior to all this, my phone was on Euro OTA Jelly Bean
Tom9 said:
Hi guys
My XT910 was submerged in a river a couple of weeks ago. It did not short circuit, but I think it got soft bricked.
Whenever it boots, it will display AP Fastboot Flash Mode (S).
I can boot to Boot Mode Selection Menu with Power + Vol+ + Vol-, but I cannot scroll or select anything. I usually enter the page so that I can access BMM to Power Off the device or access the internal storage.
I tried to Fastboot an Asia ROM but the process got stuck at Step 2. I had no choice but to unplug USB. From then on, my laptop could never detect my phone again. I am using the latest Motorola Drivers and cable.
Today, I tried what was suggested here:
http://forum.xda-developers.com/showthread.php?t=1738769
but because my phone could not be detected by my laptop, I transferred the Boot_new.img to MicroSD and used BMM to flash new kernel. (I wasn’t sure what I was doing.)
Now, when I boot my phone, AP Fastboot Flash Mode (S), and what I get after Boot Mode Selection Menu is a brief Motorola logo and Invalid Flash Mode (S) (Boot Failure).
As of last check (half hour ago), battery health was at 96%. I cannot power down the device without BMM, or at least I don’t know how to. Can anyone assist me on restoring my phone to a functional state again?
Edit: prior to all this, my phone was on Euro OTA Jelly Bean
Click to expand...
Click to collapse
Theres no way back to ICS after updating to euro jelly bean, read the first post carefully, it warned you about it
You can use this tutorial how to unbrick it
http://forum.xda-developers.com/showthread.php?t=2194825
Sent from my GT-I9300 using xda app-developers app
I have Motorola Droid Razr XT910 and by RSD I did an update from ICS 4.0.4. to JB 4.1.2. and I decided I want to go back to GB 2.3.5. or 2.3.6. because of the battery life, what is now on JB really short, but I failed of course, so I'm stuck in AP Fastboot mode every time I want to turn my phone on, It will show me this:
Code:
AP Fastboot Flash Mode (S) (Recipe Failure)
0A.77
eMMC Info: Size 16G
To return to normal mode - first press power key to power down
Device is LOCKED. Status Code: 0
And phone is stuck in it, so I need to turn it off, and then power button + vol up + vol down and go through the normal powerup. I have tried another JellyBeans but the problem is in bootloader. I saw here on xda one post telling me I have to flash the radio - I did that about 100 times and I failed... I flashed radio (empty radio) and then in recovery did a wipe data and cache - when i go to recovery after flashing radio, phone will start loading something, maybe the radio, BUT! When it's done, phone will again show me recipe failure...I think I need to unlock bootloader to do a full wipe data and everything, and again start from over. I saw about milion posts here about this problem but with no result... Someone please help me
fufixiil said:
I have Motorola Droid Razr XT910 and by RSD I did an update from ICS 4.0.4. to JB 4.1.2. and I decided I want to go back to GB 2.3.5. or 2.3.6. because of the battery life, what is now on JB really short, but I failed of course, so I'm stuck in AP Fastboot mode every time I want to turn my phone on, It will show me this:
Code:
AP Fastboot Flash Mode (S) (Recipe Failure)
0A.77
eMMC Info: Size 16G
To return to normal mode - first press power key to power down
Device is LOCKED. Status Code: 0
And phone is stuck in it, so I need to turn it off, and then power button + vol up + vol down and go through the normal powerup. I have tried another JellyBeans but the problem is in bootloader. I saw here on xda one post telling me I have to flash the radio - I did that about 100 times and I failed... I flashed radio (empty radio) and then in recovery did a wipe data and cache - when i go to recovery after flashing radio, phone will start loading something, maybe the radio, BUT! When it's done, phone will again show me recipe failure...I think I need to unlock bootloader to do a full wipe data and everything, and again start from over. I saw about milion posts here about this problem but with no result... Someone please help me
Click to expand...
Click to collapse
You can't unlock bootloader,unfortunately no one can.
Did you try to flash JB with RSD Lite again?
Sent from my Razr XT910
welder73 said:
You can't unlock bootloader,unfortunately no one can.
Did you try to flash JB with RSD Lite again?
Sent from my Razr XT910
Click to expand...
Click to collapse
Yes, I did. I tried to first delete cache and everything and then flash new JB, or just flash it, or flash and then delete cache and data.
fufixiil said:
Yes, I did. I tried to first delete cache and everything and then flash new JB, or just flash it, or flash and then delete cache and data.
Click to expand...
Click to collapse
What do you mean "delete cache"?
Here http://forum.xda-developers.com/showthread.php?t=2231289 are the JB Fastboot files
Here https://dl.dropboxusercontent.com/u/42057363/RSDLite_v6.1.x.zip is RSD Lite 6.1.5
Here https://motorola-global-portal.custhelp.com/app/answers/detail/a_id/88481/action/auth are the Motorola drivers
Install drivers,install RSD Lite
Start RSD Lite,click on 3 dots next to empty bar,find JB Fastboot file that you downloaded,click open and then "decompress only"
When program finish that,shut the phone off,press vol- vol+ and power button,choose AP Fastboot,connect the phone with usb cable to the computer,wait a program to recognize the phone and then press start in RSD Lite.
welder73 said:
What do you mean "delete cache"?
Here http://forum.xda-developers.com/showthread.php?t=2231289 are the JB Fastboot files
Here https://dl.dropboxusercontent.com/u/42057363/RSDLite_v6.1.x.zip is RSD Lite 6.1.5
Here https://motorola-global-portal.custhelp.com/app/answers/detail/a_id/88481/action/auth are the Motorola drivers
Install drivers,install RSD Lite
Start RSD Lite,click on 3 dots next to empty bar,find JB Fastboot file that you downloaded,click open and then "decompress only"
When program finish that,shut the phone off,press vol- vol+ and power button,choose AP Fastboot,connect the phone with usb cable to the computer,wait a program to recognize the phone and then press start in RSD Lite.
Click to expand...
Click to collapse
I also have the recipe failure and have tried all of these steps (and many others) to try and fix the "recipe failure" at boot.
welder73 said:
What do you mean "delete cache"?
Here http://forum.xda-developers.com/showthread.php?t=2231289 are the JB Fastboot files
Here https://dl.dropboxusercontent.com/u/42057363/RSDLite_v6.1.x.zip is RSD Lite 6.1.5
Here https://motorola-global-portal.custhelp.com/app/answers/detail/a_id/88481/action/auth are the Motorola drivers
Install drivers,install RSD Lite
Start RSD Lite,click on 3 dots next to empty bar,find JB Fastboot file that you downloaded,click open and then "decompress only"
When program finish that,shut the phone off,press vol- vol+ and power button,choose AP Fastboot,connect the phone with usb cable to the computer,wait a program to recognize the phone and then press start in RSD Lite.
Click to expand...
Click to collapse
I mean wipe everything in recovery (cache and data). And I did now step by step and still getting recipe failure.
Good day all to you
I have the moto xt910, until this morning it was fine with 4.0.4 .
I downloaded 4.4.2 + gapps for it and prepared for updating. The xt910 is rooted, i backuped anything, i put CWM on it and then i began to boot into recovery mode. I backuped again and then did the steps I was adviced to: Wipe data/factory reset - wipe cache and then wipe dalvik cache.
After that I installed cm11 on it - everything was fine. then i needed to install the gapps stuff. i recognized i did not have it on my external sd-card so i put it the card out of the xt910 and copied that .zip from my pc to the sd-card. I put back the sd-card into the xt910, waited a minute and tried to access on it again to install gapps.... The Bootloader stucked, couldnt do anything at all, it disappeared. only option was "power+volumedown".
After this i just get the "moto logo-dualcore" sign for 10seconds, screen goes black and thats it - nothing happens.
Pressing power button - nothing happens at all. Pressing power+volumedown, the logo appears and screen goes black again, no bootloader or anything else (the screen looks like it is slightly lighted in black but absolutely nothing to do).
When i press power+volumedown and i release power when the screen flickers but still holding volumedown, it appears white font saying this:
"AP Fastboot Flash Mode (S) 0A.74 - eMMC Info: Size 16G - To return to normal mode - first press power key to power down - Device is LOCKED. Status Code: 0 - Battery OK, OK to Program, Connect USB, Data Cable"
I can press power, it goes off, I can press power, logo appears, still stuck in the same again as before . When connecting with usb it tries to install drivers, but it doesnt found anything ( Usb Driver is ok, all others failed to install)
Is the phone dead or can I somehow reset it again or make it work again?
Thanks to everyone and hope for your answers and help
Use RSD Lite to reflash your stock 4.0.4. Search for flashing with RSD Lite.
DROID RAZR with Tapatalk 4
neo.ank said:
Use RSD Lite to reflash your stock 4.0.4. Search for flashing with RSD Lite.
DROID RAZR with Tapatalk 4
Click to expand...
Click to collapse
Thanks for your help,
I already tried RSD Lite but it doesnt recognize the phone. How am I gonna do that?
I installed motorola device manager and it shows 4/5 driver ready. The one that wont work is "MTB-USB Driver"
Klicking on Motorola Device Manager it just tries to update but dont find anything, it says "Current Version: N/A"
(I havent seen those drivers before, when the phone worked the drivers were called somewhat else on computer)
csa85 said:
Thanks for your help,
I already tried RSD Lite but it doesnt recognize the phone. How am I gonna do that?
I installed motorola device manager and it shows 4/5 driver ready. The one that wont work is "MTB-USB Driver"
Klicking on Motorola Device Manager it just tries to update but dont find anything, it says "Current Version: N/A"
(I havent seen those drivers before, when the phone worked the drivers were called somewhat else on computer)
Click to expand...
Click to collapse
Try other usb port.
Turn of the phone,then turn it on,while it´s connected to usb.
If that doesn´t work,deinstall all motorola drivers,restart laptop (computer) and install them again.
And you must press vol- vol+ and power button to get to the AP Fasboot mode.