[Q] Stuck at NAND Write Start!! Help ASAP!! - Galaxy S III Q&A, Help & Troubleshooting

Hey guys,
I don't know what happened but I was trying to update my phone (GT-I9300) using Odin v3.07 and I'm getting stuck at NAND Write Start.
Also, I'm unable to boot into recovery mode.
Also, When I try to reboot my phone normally, I end up in downloading mode but without the counter and all those stats which are written in top left corner. Just plain simple downloading mode. I don't know what to do. Please help me out ASAP as my battery will die otherwise.
P.S. Phone's not charging!!! :'(

saurabh_goyal93 said:
Hey guys,
I don't know what happened but I was trying to update my phone (GT-I9300) using Odin v3.07 and I'm getting stuck at NAND Write Start.
Also, I'm unable to boot into recovery mode.
Also, When I try to reboot my phone normally, I end up in downloading mode but without the counter and all those stats which are written in top left corner. Just plain simple downloading mode. I don't know what to do. Please help me out ASAP as my battery will die otherwise.
P.S. Phone's not charging!!! :'(
Click to expand...
Click to collapse
I guess you Messed it up.. Wish any dev could help ya
GOOD LUCK :good:.

BHARGAV33 said:
I guess you Messed it up.. Wish any dev could help ya
GOOD LUCK :good:.
Click to expand...
Click to collapse
What??? Seriously?? Warranty is still there or is it void?
Download mode shows the following:
PRODUCT NAME: GT-I9300
CUSTOM BINARY DOWNLOAD: No
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom

saurabh_goyal93 said:
What??? Seriously?? Warranty is still there or is it void?
Download mode shows the following:
PRODUCT NAME: GT-I9300
CUSTOM BINARY DOWNLOAD: No
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
Click to expand...
Click to collapse
Try getting into recovery mode..
Remove the battery
Hold down the keys for recovery mode(without battery)
Then put the battery in..
Don't leave the keys until you get into recovery mode.. Probably you'd have to try flashing an new rom through recovery..make sure the first thing you do.on CWM is factory reset
---------- Post added at 03:32 AM ---------- Previous post was at 03:30 AM ----------
And also see if you could flash an new version of CWM through Odin

saurabh_goyal93 said:
What??? Seriously?? Warranty is still there or is it void?
Download mode shows the following:
PRODUCT NAME: GT-I9300
CUSTOM BINARY DOWNLOAD: No
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
Click to expand...
Click to collapse
You were the one asking about hardbrick and now it seems you could have suffered one. What a fu**ed up coinsidence. Although for now it looks like a Soft-Brick
Ok first , how many % did your battery have when you started flashing?
Second, what Firmware did you flash and where did you get it (link would be good)?
The flashing counter looks good except the the System Status. It states custom which indicates that you changed the Firmware in some way which could void warranty but not always, depends on the carrier and the Service Center.

Scarface1991 said:
You were the one asking about hardbrick and now it seems you could have suffered one. What a fu**ed up coinsidence. Although for now it looks like a Soft-Brick
Ok first , how many % did your battery have when you started flashing?
Second, what Firmware did you flash and where did you get it (link would be good)?
The flashing counter looks good except the the System Status. It states custom which indicates that you changed the Firmware in some way which could void warranty but not always, depends on the carrier and the Service Center.
Click to expand...
Click to collapse
1) Around 50% but the amount of battery left is much much less than that. I can feel it.
2) XXDLJ4 from Sammobile. I can't find the link. But it was official firmware from UK.
I live in India. We don't have carrier specific phones yet. But I have no idea what service centre guys are going to say. I'm just gonna tell him that I was updating using kies and this happened.

BHARGAV33 said:
Try getting into recovery mode..
Remove the battery
Hold down the keys for recovery mode(without battery)
Then put the battery in..
Don't leave the keys until you get into recovery mode.. Probably you'd have to try flashing an new rom through recovery..make sure the first thing you do.on CWM is factory reset
---------- Post added at 03:32 AM ---------- Previous post was at 03:30 AM ----------
And also see if you could flash an new version of CWM through Odin
Click to expand...
Click to collapse
Thanks for your reply but I'm unable to get into recovery mode. I tried what you said.

XXDLJ4 is outdated and is from 2012. From what Google says it`s Android 4.1.1 . There are newer Firmwares around. The newest Firmware to my knowledge is XXEMC3. However it doesn`t matter what the Firmware is, it should work even if the Firmware is old. Do you still have the log from Odin? It would be good to see where Odin failed exactly. A screenshot would be great.

Scarface1991 said:
XXDLJ4 is outdated and is from 2012. From what Google says it`s Android 4.1.1 . There are newer Firmwares around. The newest Firmware to my knowledge is XXEMC3. However it doesn`t matter what the Firmware is, it should work even if the Firmware is old. Do you still have the log from Odin? It would be good to see where Odin failed exactly. A screenshot would be great.
Click to expand...
Click to collapse
Yeah. Sure. Here you go.

Ok a friend of mine had the same issue one time with his I9000 and it helped to switch the USB Ports and then try to flash the firmware again. Also turn off every process that belongs to Kies. Go to Task manager and Kill every Kies process.
Also try to use Odin 1.85, I`ve seen people having problems with Odin 3.xx before

Scarface1991 said:
Ok a friend of mine had the same issue one time with his I9000 and it helped to switch the USB Ports and then try to flash the firmware again. Also turn off every process that belongs to Kies. Go to Task manager and Kill every Kies process.
Also try to use Odin 1.85, I`ve seen people having problems with Odin 3.xx before
Click to expand...
Click to collapse
I'll do that. Give me two mins.
P.S. Can I somehow charge my phone's battery? Like through a wall socket? It shows old style downloading mode with no info whatsoever if I do that? Is it charging?

Scarface1991 said:
Ok a friend of mine had the same issue one time with his I9000 and it helped to switch the USB Ports and then try to flash the firmware again. Also turn off every process that belongs to Kies. Go to Task manager and Kill every Kies process.
Also try to use Odin 1.85, I`ve seen people having problems with Odin 3.xx before
Click to expand...
Click to collapse
Same issue! I even reinstalled the drivers!!

saurabh_goyal93 said:
I'll do that. Give me two mins.
P.S. Can I somehow charge my phone's battery? Like through a wall socket? It shows old style downloading mode with no info whatsoever if I do that? Is it charging?
Click to expand...
Click to collapse
Nope I don`t think it`s charging. That`s why almost every flashing guide says that you should have a fully charged battery before you flash a ROM to your device.
Edit: Ok this is weird. I would try a different Firmware.

Scarface1991 said:
Nope I don`t think it`s charging. That`s why almost every flashing guide says that you should have a fully charged battery before you flash a ROM to your device.
Click to expand...
Click to collapse
Yeah I know that. But this thing has never ever happened to me. So I guess I was over-confident!

Turn your phone off so the battery won`t die. Then download the latest Firmware and flash it the same way you did before. This is the only thing that you could do to my knowledge.
Do you have a Custom ROM on your phones internal or external SD? If yes you could follow up on BHARGAV33`s tip to flash CWM Recovery through Odin and then try to access Recovery and afterwards wipe data and flash a new ROM.

saurabh_goyal93 said:
Yeah. Sure. Here you go.
Click to expand...
Click to collapse
i faced same problem in two of my USB ports and was successful in the other ones ! as the senior member said try changing your pc USB ports. good luck ! :good:

Scarface1991 said:
Nope I don`t think it`s charging. That`s why almost every flashing guide says that you should have a fully charged battery before you flash a ROM to your device.
Edit: Ok this is weird. I would try a different Firmware.
Click to expand...
Click to collapse
I've tried all the firmwares which I have! Android 4.0.4, 4.1.1, 4.1.2, everything!
No change in result!

Its bricked...hard bricked...send it off if you have warranty...it happened to me.
Sent from my Vivid 4G using xda app-developers app

"NAND Erase All" is worth trying?
Scarface1991 said:
Turn your phone off so the battery won`t die. Then download the latest Firmware and flash it the same way you did before. This is the only thing that you could do to my knowledge.
Do you have a Custom ROM on your phones internal or external SD? If yes you could follow up on BHARGAV33`s tip to flash CWM Recovery through Odin and then try to access Recovery and afterwards wipe data and flash a new ROM.
Click to expand...
Click to collapse
Doing that only for the some past hours. No, I'm unable to get into recovery in the way he said. I've already tried it. I searched around on forum & some people were able to tackle their issue by flashing a complete firmware with 3 files. I download the whole firmware which had 3 files but still no luck. I'm going crazy over here, should I just give my phone to Samsung Care and let them deal with it? Or is there anything left to try?
And BTW, I gotta ask, what exactly happens if someone ticks "NAND Erase All" in odin when flashing a firmware. I've not done this because according to me, it's not advisable to play with things which you don't know about.
1) So, what does "NAND Erase All" in odin do exactly?
2) Will it somehow be helpful in my situation?
3) Also, some people on XDA say that NAND Erase All hard bricks your phone & warranty is also void. Is this true?

[email protected] said:
Its bricked...hard bricked...send it off if you have warranty...it happened to me.
Sent from my Vivid 4G using xda app-developers app
Click to expand...
Click to collapse
Download mode shows the following:
PRODUCT NAME: GT-I9300
CUSTOM BINARY DOWNLOAD: No
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom <<<<<<< This is the part I'm worried about!!
Is my warranty voided or not?

Related

[Q] [HELP!] S3 wont even boot

So my S3 went into a boot loop. And I dont know how I got to this point but now the phone wont even boot, when plugged in to my comp it shows the battery symbol but its greyed out with the circle in the middle, and it stays like that. If i hold the power putton it comes up with the Galaxy SIII GT i9300 screen but then goes back to the battery. I can get it to go into download mode though. I think somehow I may have deleted all the files required for the phone to actually boot(Im a n00b so im not completely sure) Can somebody please help me?
I was on custom ROM before and my binary counter is at 4, so sending into samsung doesn't sound like a great idea :/
Thanks for the help and sorry if this has been asked before, I have searched for hours.
Luke2508 said:
So my S3 went into a boot loop. And I dont know how I got to this point but now the phone wont even boot, when plugged in to my comp it shows the battery symbol but its greyed out with the circle in the middle, and it stays like that. If i hold the power putton it comes up with the Galaxy SIII GT i9300 screen but then goes back to the battery. I can get it to go into download mode though. I think somehow I may have deleted all the files required for the phone to actually boot(Im a n00b so im not completely sure) Can somebody please help me?
I was on custom ROM before and my binary counter is at 4, so sending into samsung doesn't sound like a great idea :/
Thanks for the help and sorry if this has been asked before, I have searched for hours.
Click to expand...
Click to collapse
If you also can go into recovery, try to wipe. In addition did you flash any custom kernel?
If not, try to reflash a rom with odin after you got into download mode or did you try this already?
Sent from my GT-I9300 using xda app-developers app
chrismast said:
If you also can go into recovery, try to wipe. In addition did you flash any custom kernel?
If not, try to reflash a rom with odin after you got into download mode or did you try this already?
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
If you mean with CWM mod, no I cant, it just shows the Galaxy S3 GT i9300 screen then goes black. Yes i did have a custom kernel, I believe it was the latest Perseus one. I already tried this with a stock rom and it idnt work, it said it had passed but i still can boot the phone.
Luke2508 said:
If you mean with CWM mod, no I cant, it just shows the Galaxy S3 GT i9300 screen then goes black. Yes i did have a custom kernel, I believe it was the latest Perseus one. I already tried this with a stock rom and it idnt work, it said it had passed but i still can boot the phone.
Click to expand...
Click to collapse
as you can go into download mode but not recovery, what about flashing CWM another time (if you did not try it already). Maybe it solves the issue with recovery and from there you could go on trying to wipe etc.
Other options would be to do a mega or super wipe (if this is possible from odin & download mode, not sure though), to get your phone completely empty (mega) or at least to factory reset (super).
Luke2508 said:
So my S3 went into a boot loop. And I dont know how I got to this point but now the phone wont even boot, when plugged in to my comp it shows the battery symbol but its greyed out with the circle in the middle, and it stays like that. If i hold the power putton it comes up with the Galaxy SIII GT i9300 screen but then goes back to the battery. I can get it to go into download mode though. I think somehow I may have deleted all the files required for the phone to actually boot(Im a n00b so im not completely sure) Can somebody please help me?
I was on custom ROM before and my binary counter is at 4, so sending into samsung doesn't sound like a great idea :/
Thanks for the help and sorry if this has been asked before, I have searched for hours.
Click to expand...
Click to collapse
Look at the tread above yours,sudden death.
You are not the only one here mate.
I have it too.
Mods,can we have one tread for this huge problem.
It seems that there are many of us have this problem.
Thanks.
painterceessie said:
Look at the tread above yours,sudden death.
You are not the only one here mate.
I have it too.
Mods,can we have one tread for this huge problem.
Pointless having another thread why not post /read the original thread for this problem .
a hint look for sudden death thread
jje
Click to expand...
Click to collapse
chrismast said:
as you can go into download mode but not recovery, what about flashing CWM another time (if you did not try it already). Maybe it solves the issue with recovery and from there you could go on trying to wipe etc.
Other options would be to do a mega or super wipe (if this is possible from odin & download mode, not sure though), to get your phone completely empty (mega) or at least to factory reset (super).
Click to expand...
Click to collapse
I successfully flashed CF root with CWM, now shall I do a wipe and then restore back to a nandroid backup I made? and if so how will I? The phone now shows the samsung logo when turned on but just stays there forever.
JJEgan said:
painterceessie said:
Look at the tread above yours,sudden death.
You are not the only one here mate.
I have it too.
Mods,can we have one tread for this huge problem.
Pointless having another thread why not post /read the original thread for this problem .
a hint look for sudden death thread
jje
Click to expand...
Click to collapse
Oke sorry mate.
I didn't no that.
Click to expand...
Click to collapse
Furthermore i suggest anyone having motherboard dead problems and vendor Samsung saying no warranty .
To pull up the many posts regarding this now known manufacturing defect and don't accept in this case root/ custom rom warranty is rejected .
jje
JJEgan said:
Furthermore i suggest anyone having motherboard dead problems and vendor Samsung saying no warranty .
To pull up the many posts regarding this now known manufacturing defect and don't accept in this case root/ custom rom warranty is rejected .
jje
Click to expand...
Click to collapse
The thing is there is nothing wrong with my phone in terms of hardware. The problem that I am having is purely software, I think I just need to restore my phone to a previous version. I did see that thread but didnt feel my post belonged there as my problem is nothing to do with broken battery or mobo or anything along those lines. Hence why I am posting here
Just factory reset via recovery then flash a stock rom via Odin .
No recovery flash CF root via Odin .
jje
JJEgan said:
Just factory reset via recovery then flash a stock rom via Odin .
No recovery flash CF root via Odin .
jje
Click to expand...
Click to collapse
I did install a stock ROM and it was still stuck on bootloop, left it like that for an hour, still nothing. So I went into CWM (after flashing it) Wiped and factory reset (noticing it said error mounting /data but ignored) and then restored with a backup I had. it did say error mounting /data and so skipped that step. Still stuck in boot loop. now that I try wiping again the same error occurs, error mounting /data any ideas please?
I did have this problem a few days back. The only thing i did was downloaded my Carrier stock firmwaer and extracted boot.img and used Samsung galaxy toolkit and make a filé that i was able to use with Odin. Dunno if ot helps you but my Phone is still going strong
I was only trying to root my Phone tho. No custom rom installera when i got The boot problem
Sounds like you have permission problem. I can't find the three about that but I update my post here if I can find it.
you can try to fix permission in cwm it seems, hope it works
Sent from my GT-I9300 using xda app-developers app
xda-napp3 said:
I did have this problem a few days back. The only thing i did was downloaded my Carrier stock firmwaer and extracted boot.img and used Samsung galaxy toolkit and make a filé that i was able to use with Odin. Dunno if ot helps you but my Phone is still going strong
I was only trying to root my Phone tho. No custom rom installera when i got The boot problem
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
Thanks, do you have any idea where I will find my carrier specific firmware? And any other kind of tips on how to do/get things? But hopefully this works
Checkout this thread hope you find what you need there
http://forum.xda-developers.com/showthread.php?t=1927113
Sent from my GT-I9300 using xda app-developers app

[Q] Non-Responsive Touchscree & ODIN Won't Flash

Ok, I flashed the experimental 4.2.1 update from temasek earlier. flashed his custom kernel. all worked fine.
Told me my SD Card was 'damaged', which I now understand just needed a fix which was provided. However I decided to just forget it and restore my nandroid backup i'd taken the previous night.
Checked the folder was there, which it was, so booted to CWM, did all the wipes and chose "restore". much to my horror, it failed to find any files.
stupid mistake part: i decided to flash the perseus kernel back over the top to see if the CWM would recognise my nandroid files and restore them
the screen just went mad - had blue lines all over the place, the samsung logo jumped about and the screen went off.
i booted back to CWM and found the touchscreen was unresponsive. everything else worked - buttons, CWM. The phone is also recognised in ODIN, so I grabbed the latest stock JB leak and flashed it. it flashed fine, but it was a middle eastern rom, which didn't help, and the touchscreen was still dead.
the PC still recognised it, so i coped the temasek files back on to see if i could re-flash those, which i did, but still no luck with the touchscreen.
flashed the JB leak again with ODIN, which worked. plugged it in to the PC and copied across a nandroid backup folder i'd taken earlier in the evening last night, since the other one seems to not work. rebooted and it still wouldn't find it.
Now i've got the latest stock rom for the uk but ODIN just won't flash anything - the phone is recognised, the MD5 sum on the rom checks out but i always get "Complete(Write) operation failed" error each time. I plug the phone in to the PC, and it recognises it just fine, but KIES is sitting on the "connecting" screen and not doing anything - i've reinstalled the latest drivers as well.
I'm starting to be resigned to the fact i've killed it, but if anyone has any ideas, i'd be hugely grateful - thankyou
touchscreen dead is getting more and more common. Not sure what is going on but if u cant flash anything from odin maybe u have dead mmc chip or something. Hopefully you resolve it or a trip to sammy service centre hopefully can fix under warranty for u
Edit close down all kies software whilst using odin
Sent from my GT-I9300 using XDA Premium HD app
i dont have warranty as the phone was bought second hand.
i'm just on the phone to my insurance providers though for accidental damage ..it might mean i have to drop it downstairs though !
ooeerr .. rebooted my PC, reconnected to ODIN and it's flashing the UK Stock ROM i got .. fingers crossed. I really don't want to have to drop it downstairs. The insurers will want to inspect it and if there's a custom rom on it, it might get bounced
hankhandsome said:
Ok, I flashed the experimental 4.2.1 update from temasek earlier. flashed his custom kernel. all worked fine.
Told me my SD Card was 'damaged', which I now understand just needed a fix which was provided. However I decided to just forget it and restore my nandroid backup i'd taken the previous night.
Checked the folder was there, which it was, so booted to CWM, did all the wipes and chose "restore". much to my horror, it failed to find any files.
stupid mistake part: i decided to flash the perseus kernel back over the top to see if the CWM would recognise my nandroid files and restore them
the screen just went mad - had blue lines all over the place, the samsung logo jumped about and the screen went off.
i booted back to CWM and found the touchscreen was unresponsive. everything else worked - buttons, CWM. The phone is also recognised in ODIN, so I grabbed the latest stock JB leak and flashed it. it flashed fine, but it was a middle eastern rom, which didn't help, and the touchscreen was still dead.
the PC still recognised it, so i coped the temasek files back on to see if i could re-flash those, which i did, but still no luck with the touchscreen.
flashed the JB leak again with ODIN, which worked. plugged it in to the PC and copied across a nandroid backup folder i'd taken earlier in the evening last night, since the other one seems to not work. rebooted and it still wouldn't find it.
Now i've got the latest stock rom for the uk but ODIN just won't flash anything - the phone is recognised, the MD5 sum on the rom checks out but i always get "Complete(Write) operation failed" error each time. I plug the phone in to the PC, and it recognises it just fine, but KIES is sitting on the "connecting" screen and not doing anything - i've reinstalled the latest drivers as well.
I'm starting to be resigned to the fact i've killed it, but if anyone has any ideas, i'd be hugely grateful - thankyou
Click to expand...
Click to collapse
unfortunately your touchscreen died and your only option is to bring it for warranty because of the bad flash, if you have warranty i suggest follow my simple guide here.
http://forum.xda-developers.com/showthread.php?t=2074756
---------- Post added at 01:52 PM ---------- Previous post was at 01:49 PM ----------
hankhandsome said:
i dont have warranty as the phone was bought second hand.
i'm just on the phone to my insurance providers though for accidental damage ..it might mean i have to drop it downstairs though !
ooeerr .. rebooted my PC, reconnected to ODIN and it's flashing the UK Stock ROM i got .. fingers crossed. I really don't want to have to drop it downstairs. The insurers will want to inspect it and if there's a custom rom on it, it might get bounced
Click to expand...
Click to collapse
still follow the guide so the insurance will not detect that you have been rooted before
chris151722 said:
still follow the guide so the insurance will not detect that you have been rooted before
Click to expand...
Click to collapse
i'll see what i can do but it's now stuck in a bootloop after flashing the rom i grabbed earlier, so will try another one.
i might have to kill it stone dead if none of this works
each rom i try in ODIN never boots - just goes into a bootloop.
i suppose if the insurers do inspect it, they may well not be able to get to see the flash counter if they can't boot it up - so it'll have a stock, unrooted rom on it anyway, so does anyone think i'll be ok ?
hankhandsome said:
i'll see what i can do but it's now stuck in a bootloop after flashing the rom i grabbed earlier, so will try another one.
i might have to kill it stone dead if none of this works
Click to expand...
Click to collapse
after you flash stock firmware go to recovery try to factory reset
---------- Post added at 02:15 PM ---------- Previous post was at 02:11 PM ----------
Ausboy 2011 said:
touchscreen dead is getting more and more common. Not sure what is going on but if u cant flash anything from odin maybe u have dead mmc chip or something. Hopefully you resolve it or a trip to sammy service centre hopefully can fix under warranty for u
Edit close down all kies software whilst using odin
Sent from my GT-I9300 using XDA Premium HD app
Click to expand...
Click to collapse
its a bad flash from odin and bad flash thru phone the reason why touch is dying.
chris151722 said:
its a bad flash
Click to expand...
Click to collapse
every rom though ?
just tried another one and it's bootlooping ..
hankhandsome said:
every rom though ?
just tried another one and it's bootlooping ..
Click to expand...
Click to collapse
can you access recovery mode? if so try to wipes or factory reset before and after firmware flash
chris151722 said:
can you access recovery mode? if so try to wipes or factory reset before and after firmware flash
Click to expand...
Click to collapse
at the moment i can't access anything - it just sits at the samsung logo now. CWM is now no longer accessible either - i pop the battery, wait a few minutes then put it back in. I hold down Up/Power/Middle button and the Samsung Logo flashes, but nothing happens.
I can still put it in to download mode and flash roms with odin, but nothing happens .. i think i'm going to have to accept it's dead
My last roll of the dice is to grab one of the earlier roms from this thread
http://forum.xda-developers.com/showthread.php?t=1835931
and see what that does in ODIN
FYI:
1. you don't have to wipe anything before restoring a backup, it doesn't make a difference.
2. insurance fraud is a felony
Glebun said:
FYI: 2. insurance fraud is a felony
Click to expand...
Click to collapse
Good job i don't live in the US then ..
I'm pretty sure it's illegal no matter where you live
Well I don't particularly want to get into an argument here, as i'd much prefer a phone that works so i'll just thank you for your input.
i think you have to solve the bootloop issue first by searching in the forum, im not expert so cant give you better advice on bootloop,
chris151722 said:
i think you have to solve the bootloop issue first by searching in the forum, im not expert so cant give you better advice on bootloop,
Click to expand...
Click to collapse
thanks. it doesn't actually bootloop now, it just sits on the glowing samsung logo and doesn't move.
i just want to get a stock rom back on it and i'm going to just let it go. i'm a bit concerned that on the download screen it says "Custom Binary Download: Yes (19 Counts)". I know I did reset the flash counter not too long ago before I flashed the Darky Rom, so if this is indeed the flash counter, then i've obviously not done something right, so it'll show multiple flashes ..
ok, we've had developments ..
i actually got it in to CWM (don't know how..) and did a factory reset. it then did boot up into the OS but - no touchscreen still.
however, i've just tried connecting it to KIES and it's detected it so i'm going to try the emergency recovery thing ..
he says, as he selects the option and KIES then goes back to "connecting" .. *GROAN* .. and then comes back to tell me it's not supported to upgrade firmware via KIES .. *BIGGER GROAN*
Ok, downloaded and flashed an earlier rom for the UK but still no luck with the screen. Kies won't do any kind of emergency firmware upgrade either so that's that. i'll have to try and get one of those OTG USB dongles so i can get the flash counter reset though ..
hankhandsome said:
Ok, downloaded and flashed an earlier rom for the UK but still no luck with the screen. Kies won't do any kind of emergency firmware upgrade either so that's that. i'll have to try and get one of those OTG USB dongles so i can get the flash counter reset though ..
Click to expand...
Click to collapse
Does not reset flash counter only allows access to download mode. Traingle Away to reset flash counter .
jje
JJEgan said:
Does not reset flash counter only allows access to download mode. Traingle Away to reset flash counter .
jje
Click to expand...
Click to collapse
i'm aware of that - that's why I've ordered the OTG dongle so I can use my desktop mouse to go in and install triangle away

[Q] I9300 is stuck on white samsung screen, Help please!

I have the international edition of the S3 that a was messing around with, and I ended up installing some rom and now I can't even get into recovery. I've searched around and tried multiple methods of fixing it. The only thing I can access is download mode. Can anyone help?
same my condition ..... it's looks like sudden death ..... try flash any recovery files ... if not ... ur last hope doing PIT then if u failed to 100% successfully .... need a new MotherBoard ... replace it if warranty recover
ps: act like fool and tell them u have sudden Death and u didnt play with anything (dont mention ur flash custom rom/firmware ....it will cancel ur warranty)
sry for lose man , u not the only one ... i cant even replace it with warranty due to bought from another country
good luck
speedman2202 said:
same my condition ..... it's looks like sudden death ..... try flash any recovery files ... if not ... ur last hope doing PIT then if u failed to 100% successfully .... need a new MotherBoard ... replace it if warranty recover
ps: act like fool and tell them u have sudden Death and u didnt play with anything (dont mention ur flash custom rom/firmware ....it will cancel ur warranty)
sry for lose man , u not the only one ... i cant even replace it with warranty due to bought from another country
good luck
Click to expand...
Click to collapse
Do you know where I could find instructions on how to flash a PIT?
this is file come from sammobile.com website
providing u the right PIT file with flasher
http://www.mediafire.com/?ddfpfkk2pb8326k
connect ur mobile , open odin program and then press on PIT button and navigate PIT files then (as i think) choose the latest PIT file with name i9300 (ur mobile Model) and latest date and then hit start ..... good luck but i recommend u send it to ur Samsung repair center if warranty cover
good luck
stop!
before messing with pit files, which is extremely dangerous, flash a stock ROM through Odin and then do a factory reset from recovery
Glebun said:
stop!
before messing with pit files, which is extremely dangerous, flash a stock ROM through Odin and then do a factory reset from recovery
Click to expand...
Click to collapse
Exactly this^^^^....pit file flashing is an absolute last resort, not a first solution
did you tried flashing 4.0.4 stock rom with odin?
same thing happened to me 2 weeks ago, flashing 4.0.4 and after that flashing 4.1.2 fixed it.
try to do not mess with pit especially if you didn't backup your efs folder. it is not needed.
redstreetwalker said:
it is not needed.
Click to expand...
Click to collapse
moreover, it can render your phone irreparable
Ganjasaur said:
now I can't even get into recovery. The only thing I can access is download mode.
Click to expand...
Click to collapse
Glebun said:
stop!
before messing with pit files, which is extremely dangerous, flash a stock ROM through Odin and then do a factory reset from recovery
Click to expand...
Click to collapse
he cant go to Recovery mode ......(same like my condition) , he just can go to download mode
Glebun said:
stop!
before messing with pit files, which is extremely dangerous, flash a stock ROM through Odin and then do a factory reset from recovery
Click to expand...
Click to collapse
I've already tried to flash a stock firmware, but I still couldn't get it into recovery. I'm not sure if it was the right one though. I have a regular unbranded SIII, is there a specific firmware I should flash?
speedman2202 said:
he cant go to Recovery mode ......(same like my condition) , he just can go to download mode
Click to expand...
Click to collapse
okay? the first thing to do here is just flash a stock ROM, no need for pit files
Mine was stuck before than samsung logo, on the model number screen. Almost 1 second or less after opening the device.
Then i flashed 4.0.4 and magically it opened without any loop or something. Its useless to flash 4.1.2 or any other jb stock rom, for some reason it seems not fixing the loop issue.
Again, there is no problem related with pit files.
Sent from my GT-I9300 using xda premium
It's all individual, what worked for you might not work for others. Don't say that flashing JB is useless, because it's not
I flashed stock 4.0.4 firmware through odin. The operation was successful, but I was still unable to enter recovery. What am I doing wrong?
Ganjasaur said:
I flashed stock 4.0.4 firmware through odin. The operation was successful, but I was still unable to enter recovery. What am I doing wrong?
Click to expand...
Click to collapse
Follow the steps to root and flash your custom ROM again as if you just got your phone. The same thing happened to my T999, and it took me 3 tries doing this to finally get back into Recovery.
try to flash in odin stock rom then root use cwm then try to go to recovery..
My cousin's having the same exact issue and we've been unable to find the proper rom. Can anyone please tell me where to get one? I've downloaded some "international" ones but when i try to upload it it keeps telling me failed, i've tried at least 4 or 5 different roms.
ANY help would be greatly appreciated!!
Phone is:
GT-i9300
using it in the US with StraightTalk in the US (been working like a charm for ~6 months, all of a suddent when into this weird limp mode)
Phone was running jellybean 4.1.1 (through kies) and not rooted
Try several times before giving up. Sometimes it works after when the device feels that you've had enough stress and fear.
I mean the problem is common but it's solved in different ways or different repeats.
But it seems that your problem is a software problem that can be solved.
Glebun said:
It's all individual, what worked for you might not work for others. Don't say that flashing JB is useless, because it's not
Click to expand...
Click to collapse
Sorry for the misunderstanding, i mean flashing jb was useless for me in that situation. Thanks for the correction
Sent from my GT-I9300 using xda premium

[Q] Firmware Upgrade Error

Sorry if this is answered on another thread; I couldn't find any answer that helped me, so I am opening this thread.
My Galaxy S3 I9300 is stuck with the error: "Firmware Upgrade encountered an issue. Please select recovery mode in Kies & try again."
But when I try to upgrade using Kies I get the error message "This device's version cannot be updated." I get as far as entering my model number and S/N.
I cannot enter recovery mode on my S3, only download mode, so I am unable to perform a hard reset.
My phone is not compatible with Kies3 so I am using Kies.
Any suggestions?
make sure your phone is not rooted,otherwise kies becomes unvailable.
Flash stock ROM via Odin Download at http://www.sammobile.com/firmwares/
How can I tell?
alecore said:
make sure your phone is not rooted,otherwise kies becomes unvailable.
Click to expand...
Click to collapse
How can I tell if the phone is rooted? I got the phone second hand last week, and I don't know if it had previously been rooted.
In download mode, I see the following:
ODIN MODE
PRODUCT NAME: GT-I9300
CUSTOM BINARY DOWNLOAD: No
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
I am guessing this means it hasn't been rooted?
rmurray1975 said:
How can I tell if the phone is rooted? I got the phone second hand last week, and I don't know if it had previously been rooted.
In download mode, I see the following:
ODIN MODE
PRODUCT NAME: GT-I9300
CUSTOM BINARY DOWNLOAD: No
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
I am guessing this means it hasn't been rooted?
Click to expand...
Click to collapse
Download root checker from google play
On what?
nikctsh said:
Download root checker from google play
Click to expand...
Click to collapse
This may seem a stupid question but on what am I supposed to download Root Checker? I cannot access my S3 (the reason for this thread).
rmurray1975 said:
This may seem a stupid question but on what am I supposed to download Root Checker? I cannot access my S3 (the reason for this thread).
Click to expand...
Click to collapse
So why don't you provide us more details on why your phone stuck with that error message so that we can help you. You say you just got the phone second hand last week, so apparently the phone still works when you first get your hand on it. You must have done something to it, causing it to stuck with that error?
This is how I got it
nikctsh said:
So why don't you provide us more details on why your phone stuck with that error message so that we can help you. You say you just got the phone second hand last week, so apparently the phone still works when you first get your hand on it. You must have done something to it, causing it to stuck with that error?
Click to expand...
Click to collapse
This is the state I got the phone in. I had taken a quick check on the internet to see how to resolve the issue, and thought it would be worth the cost of the phone (40 Euros) to try to fix it myself. Guess I was wrong!
rmurray1975 said:
This is the state I got the phone in. I had taken a quick check on the internet to see how to resolve the issue, and thought it would be worth the cost of the phone (40 Euros) to try to fix it myself. Guess I was wrong!
Click to expand...
Click to collapse
I'm not sure whether this can help, but try mate.
1) Enter download mode and install stock rom using ODIN (preferred)
If this doesn't do the trick, try another EXPERIMENTAL alternative way,
2) Enter download mode, root your device using CF root using ODIN, flash a custom recovery using ODIN, boot into your custom recovery, flash a custom rom (risky)
I never encountered this before so I have no idea whether this can actually help or not, so do this at your own risk.
You are a star!
nikctsh said:
I'm not sure whether this can help, but try mate.
1) Enter download mode and install stock rom using ODIN (preferred)
If this doesn't do the trick, try another EXPERIMENTAL alternative way,
2) Enter download mode, root your device using CF root using ODIN, flash a custom recovery using ODIN, boot into your custom recovery, flash a custom rom (risky)
I never encountered this before so I have no idea whether this can actually help or not, so do this at your own risk.
Click to expand...
Click to collapse
You are my new hero!!!
I flashed the stock rom in Odin 3.09 and it worked a treat! I have a working telephone!
Thank you very much!!!
rmurray1975 said:
You are my new hero!!!
I flashed the stock rom in Odin 3.09 and it worked a treat! I have a working telephone!
Thank you very much!!!
Click to expand...
Click to collapse
You are welcome mate, glad that I helped you

Stuck in NAND Write - Odin

Hey guys,
I'm trying to flash a brazilian firmware in my G925i thru ODIN, but the process stucks in NAND WRITE and nothing happen.
Someone knows what can I do?
I've heard somewhere that this is a hard brick
Sent from my Nexus 9 using XDA Free mobile app
Dudmaster said:
I've heard somewhere that this is a hard brick
Sent from my Nexus 9 using XDA Free mobile app
Click to expand...
Click to collapse
What kind of brick?
rafaelpinaf said:
Hey guys,
I'm trying to flash a brazilian firmware in my G925i thru ODIN, but the process stucks in NAND WRITE and nothing happen.
Someone knows what can I do?
Click to expand...
Click to collapse
Hey there, I had a similar problem, what I did was re-install the Samsung drivers and reboot the computer also I turned off my lock screen and activation on the phone. Between the two of those things it allowed ODIN to have success.
androidvergen said:
Hey there, I had a similar problem, what I did was re-install the Samsung drivers and reboot the computer also I turned off my lock screen and activation on the phone. Between the two of those things it allowed ODIN to have success.
Click to expand...
Click to collapse
Even you have to put the phone in Download mode?
Edit: I tried the same and it still does not work :/
I tried again, but this time I ran the Odin as administrator. I passed thru NAND Write but in the end of all process it says FAIL and brick my phone.
I am trying to flash this file: G925IDVU1AOD1_G925IZTO1AOD1_G925IDVU1AOD1_HOME.tar.md5
You can see the issue attached:
you fail because you need a pit file..I can flash my normal firmware without a problem..but if I try a other one for example a provider one..it fails..for that we need the pit..and for that we need root..to extract it from the phone..and I don't won't to root ATM..
So how can I fix the device?
I tryng to use the Smart Switch PC but my device does not appear in the list to recovery emergency
I reinstalled the usb driver..
rafaelpinaf said:
So how can I fix the device?
I tryng to use the Smart Switch PC but my device does not appear in the list to recovery emergency
I reinstalled the usb driver..
Click to expand...
Click to collapse
you just need the version as firmware...you had before on the phone..this should flash
Alex-V said:
you just need the version as firmware...you had before on the phone..this should flash
Click to expand...
Click to collapse
I dont remember the older version, or the original version that was in my phone. It is stuck in Warning screen
rafaelpinaf said:
I dont remember the older version, or the original version that was in my phone. It is stuck in Warning screen
Click to expand...
Click to collapse
warning screen is no problem..it's still the download mode..but you need to know the firmware..may try to reboot both.. phone get into the warning mode again..to ensure good connection and retry smart switch
rafaelpinaf said:
I tried again, but this time I ran the Odin as administrator. I passed thru NAND Write but in the end of all process it says FAIL and brick my phone.
I am trying to flash this file: G925IDVU1AOD1_G925IZTO1AOD1_G925IDVU1AOD1_HOME.tar.md5
You can see the issue attached:
Click to expand...
Click to collapse
I've had this problem before, are you planning on rooting as well?
tiboric said:
I've had this problem before, are you planning on rooting as well?
Click to expand...
Click to collapse
No, I just want to change the firmware version because the version that came with the phone does not have Portuguese as all language. The revice was 100% stock, just tried to flash another country firmware thru Odin and it has been bricked.
rafaelpinaf said:
No, I just want to change the firmware version because the version that came with the phone does not have Portuguese as all language. The revice was 100% stock, just tried to flash another country firmware thru Odin and it has been bricked.
Click to expand...
Click to collapse
O.k the only way I know around this without finding your original firmware and flashing that, is to:
flash the firmware again, and wait until it fails again,
then hold vol down + power + home to get it to restart in to download mode again but keep odin open,
then flash CF autoroot .
then wait for the phone to reboot and it will install root then it will restart two more times on it own then should boot into the O.S.
(i take no responsibility if you mess up you device though but I have done this on more than one occasion and it always works for me)
I expect you could probably do this will another recovery(stock/twrp) instead of the CF autoroot one but have yet to try.
but you probably will be better off finding original firmware but you will not have Portuguese as you want.
Good luck with trying to fix your device
tiboric said:
O.k the only way I know around this without finding your original firmware and flashing that, is to:
flash the firmware again, and wait until it fails again,
then hold vol down + power + home to get it to restart in to download mode again but keep odin open,
then flash CF autoroot .
then wait for the phone to reboot and it will install root then it will restart two more times on it own then should boot into the O.S.
(i take no responsibility if you mess up you device though but I have done this on more than one occasion and it always works for me)
I expect you could probably do this will another recovery(stock/twrp) instead of the CF autoroot one but have yet to try.
but you probably will be better off finding original firmware but you will not have Portuguese as you want.
Good luck with trying to fix your device
Click to expand...
Click to collapse
Does the CF Autoroot work with G925I?
rafaelpinaf said:
Does the CF Autoroot work with G925I?
Click to expand...
Click to collapse
according to this you can use 925F version but I can not confirm my self as i don't have the device, If you don't mind rooting and tripping knox, I don't think you can do much more harm
androidvergen said:
Hey there, I had a similar problem, what I did was re-install the Samsung drivers and reboot the computer also I turned off my lock screen and activation on the phone. Between the two of those things it allowed ODIN to have success.
Click to expand...
Click to collapse
I also went through this problem too, and this helped thank you
But also for another phone I had to flash using a different computer for this to work.
rafaelpinaf said:
I dont remember the older version, or the original version that was in my phone. It is stuck in Warning screen
Click to expand...
Click to collapse
Maybe you can try each of the stock versions until you get the right one for your particular device. Also maybe a model number would help someone on here to identify what version you have, I don't know just throwing that out there.
My phone is G925i, and in the back says that it is made in Yateley, UK
Wich firmware you think I can try to flash?
I was trying the G925IDVU1AOD1_G925IZTO1AOD1_G925IDVU1AOD1 and then the phone has bee bricked.
rafaelpinaf said:
My phone is G925i, and in the back says that it is made in Yateley, UK
Wich firmware you think I can try to flash?
I was trying the G925IDVU1AOD1_G925IZTO1AOD1_G925IDVU1AOD1 and then the phone has bee bricked.
Click to expand...
Click to collapse
I can't link to the page I go to because of my noob post count but its samsung-updates in google. There is a whole section with various G925i versions I'm sure you'll find it there.

Categories

Resources