I got my pebble blue GS3 a week ago. It was used, but in pristine condition, with a scratch-less back and front. Since day one, I've been using a rubber back protector for the phone, which covers the back as well as the sides completely.
Today, I dropped my phone from pocket height on the floor, and picking it up I didn't notice any scratches or cracks and the phone worked perfectly fine. The phone was in the back protector as always, so I didnt think any thing of it and put it back in my pocket.
A few hours later, sitting on my laptop, I picked up my phone to make a call and noticed the golden colored discoloration in the bottom right corner of the phone (see attached pictures). I assume this was the corner on which the phone was dropped.
The discoloration appear to be air bubbles, stuck inside the screen. When I press the corner of the bubble, it shifts slightly and changes shape as air bubbles under screen protectors do. When I press it really hard, the golden starts disappearing and becomes blue just like the rest of the phone. The screen and touch works completely perfectly, and there is absolutely no difference in the quality of the AMOLED. From this, I assumed that the digitizer is fine, but I cant for the life of me figure out how these bubbles formed and why they wont go away
I searched for hours, but couldn't find a single post with the same problem. I would love to hear some ideas to try and get rid of this discoloration. I've barely had this phone for a week, and seeing it ruined already makes me sad
If it cant be fixed, I guess the final solution would be to get the front glass replaced. But before that, I would like to try any and all suggestions that you guys might want to throw my way
The glass is glued to the digitizer whit some sort of gel.
Your glass has come off the digitizer and form air bubbles.
The only way to restore it is change the glass and digitizer.
Maybe a really tight case can solve it when it pushes the glass to the digitizer.
verzonden met de xda premium app.
coolhof said:
The glass is glued to the digitizer whit some sort of gel.
Your glass has come off the digitizer and form air bubbles.
The only way to restore it is change the glass and digitizer.
Maybe a really tight case can solve it when it pushes the glass to the digitizer.
Click to expand...
Click to collapse
I was planning on getting a heat gun somehow, and heat the corner at 180F. It is said its the temperature at which the gel between the front glass and the digtizer melts or something, and becomes easy to seperate.
Do you think this would work? There is just a golden colored bubble, and it isnt affecting the working of the digitizer in any way. It is just next to the back button, and the button works absolutely perfectly.
Still waiting for any more suggestions on how to fix this Would also appreciate if someone could link me to someone with the same problem as this. I swear I've searched for hours and didnt find anything.. I can't be the only one in the world
The golden color is the top film from the digitizer.
So I don't think a heat gun is doing the job.
You can try but be very careful not to damage it more.
Wish you good luck.
Verzonden vanuit Nederland naar de rest van de wereld met de xda premium app.
bilalali said:
Still waiting for any more suggestions on how to fix this Would also appreciate if someone could link me to someone with the same problem as this. I swear I've searched for hours and didnt find anything.. I can't be the only one in the world
Click to expand...
Click to collapse
You are not alone. My S4 have the same issue, and the screen bezel is thiner than the S3... Started a couple weeks ago just after a visit to the carrier tech support, was there for unknow poor signal issue, solved by a SIM replacement and reprogramming. I know they dropped on the floor or on a work table/desk it as is "naked" without the protective case... Came back after a couple of days when I noticed the "stain" on right bottom corner and they said they handle the devices careful also have rubber pads on floor and tables to protect in the event of an "accidental drop"... So they will not replace for free, only via insurance and I have to pay a difference $$$
Anyhow, after that I dropped it so bad on rough concret right on that corner, protective case do they work but I think that corner took a good shock... I do massage the spot and it gone away for a couple of days then come back. I don't k know if temperature changes affect as it could be moisture from condesation penetrating the thin edge between bezel and screen...
I will try different cases to see if it can mask the damage until I can afford the insurance diference $ then will replace or maybe upgrade my phone...
Related
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Movisman said:
Hi all,
Ok, so i've had a small disaster. As you probably guessed already i've dropped my phone. I thought the story was quite amusing (or just plain unfortunate!) so i'll you tell that before I ask for some advice!!
I got myself a white Galaxy S2 on upgrade through Vodafone. Gorgeous piece of kit so I ordered myself a nice case and screen protector to keep it nice and tidy.
Unfortunately the case got 'lost in the post' and as such the phone was unprotected. So, with some foresight I ordered a plain white cheap one off eBay (£2 inc. postage) just to see me through the 3-5 days I needed before the case I wanted was resent.
However what was sent what not white at all - it was the most hideous case with a rather disgusting floral effect all over it. I was going out for a night in town and had no choice, I had to take it with me.
Unfortunately later that eve I was stood at the bar, and my phone went off. So to save any embarrassment I slid the phone out of it's hideous case, and proceeded to read the message. Then it happened. The slippery son of a ***** jumped out of my hand, bounced off my foot and hit the deck.
It only has a couple of dings in the chrome bezel (the chrome effect rubbed off in two places to reveal black (the plating is obviously really thin)) - everything else was ok. Phew. But i'm still gutted and annoyed with myself
So, lesson learnt. I should have left the disgusting garish floral case on and it would have saved my phone. It was only 'de-sheathed' for a second and I managed to drop it, classic.
As a temporary solution, I coloured in the affected areas of the bezel with a silver permanent marker, and used some clear nail varnish over the top to stop the pen coming off. It seems to work well actually, and it looks much better than the black marks.
So, to my question - how do I change the chrome bezel for a new one?
I have read many threads, and watched many videos, and it looks to me like a nightmare job (eg as well as taking off the back and all components, you have to prise off the screen which is glued on, disconnect digitiser, etc). Can anyone confirm this, or has anyone tried it?
I can't find any videos of changing the bezel - they all seem to only go as far as taking off the back.
I've found a couple of sellers which sell the housing in white for only £20-30, so if it's an easy-ish job i'd have a stab at it. However i'm thinking I might as well just forget it ever happened and not be so precious about keeping the phone in A1 condition - it's a phone after all and it's going to encounter some scrapes now and then, even with a case on. And I plan on keeping it for 18 months anyway.
Opinions, anyone?
Cheers!
Click to expand...
Click to collapse
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
0semaj0 said:
Sorry to hear...similar happened to my HTC Desire...however this should help...if you buy the kit off Ebay...
http://forum.xda-developers.com/showthread.php?t=1253969
Click to expand...
Click to collapse
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Movisman said:
Hi,
Thanks for the information - I had a look at this tutorial yesterday, and although it's very good, it looks like this person has replaced the entire led panel/digitiser/housing in one go, rather than just the housing?
My screen is just fine, so I only need to replace the housing part.
The hardest bit looks like separating the screen from the housing from what i've read, and this is what I can't find a tutorial for, only some images on youtube suggesting to use a hairdryer to help with the proceedings!!
Thanks
Click to expand...
Click to collapse
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
0semaj0 said:
Yea, the link is for the whole unit, but would give you some pointers. I am not as familar with the Samsung build, but with the HTC I know that between the LCD housing and the LCD/digitiser itself is applied through adhesive (most phones are) that is put into a temperature oven for 10 minutes to soften the adhesive. This is based on the HTC Official Service videos. I am not sure if the same will apply to Samsung phones.
But then again, as it is an expensive phone, it may be ideal for you to also get a quote from your local SSC or mobile phone repair agent to consider.
Click to expand...
Click to collapse
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Movisman said:
Yep, good point. I'd be interested to hear actually what the cost would be to replace the front bezel only. It's only £30 on eBay for the front and rear housing, but i'd be willing to pay more on top for an authorised repairer to carry out the job.
That tutorial is definitely one of the more detailed ones I have seen so far though. Doesn't look like many people have tackled changing the bezel only...
Thanks
Click to expand...
Click to collapse
Hey Movis,
What did you end up doing for your dropped phone?
I too have dropped my phone on its corner and the chrome along with the plastic is now dented.
Another one with the same problem here. I managed to create a bump on the chrome bezel.
Can I bump this post as I've also just noticed a ding in the corner of the chrome bezel was wondering if anyone had found a solution to this yet.? short of replacing the LCD/digitiser which like OPs phone are working fine. It's just cosmetic damage.
I once was in a bad mood and snapped a screen and backing/housing in half.I can't remember exactly,but I'm thinking the chrome bit may be part of the thin metal casing/housing that is glue taped onto the screen.
You separate the screen from the housing by using a hot air gun sparingly.
If you look back at a motherboard thread I was involved in,a person on here called Roger put up a great video tutorial link that may answer all your questions...
Sent from my GT-I9100
Ah cheers for the reply. Had a look at the mobo post you were involved in followed it to the link and coincidentally that's the exact video I watched last night. Very good video good detail and instructions. But its the black one he is stripping down so he makes no reference to the bezel which afaik is only used on the white ones.
Sent from my GT-I9100 using xda premium
I've not seen the chrome bit listed separately,so I guess its part of the metal top housing that the LCD is glued to.I've got a white one and its got a ding on it too.
You could email Samsung to see if you can get the part,but I think its not worth risking cracking the screen and you probably couldn't resuse / would get that stupid gluey tape stuff.
Sent from my GT-I9100
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
vyks10 said:
Appreciate it's been a while, but this seems to be the only post that matches what happened to me, so figured I'd update with my experience.
As above, dropped and dented the bezel, screen was perfectly intact, but the dent was so severe, it actually lifted a corner of my screen up. I have intentions to sell on so I wanted to fix this and pass on.
I followed this disassembly , apart from the bit about not worrying about damaging the screen as you prise it away. The housing I ordered off ebay came with a little kit, so I warmed the screen with hairdryer for a couple of minutes, then slowly prised it away, from top to bottom, inserting the tool right down the middle as the video mentions there is a large adhesive right down the middle.
Following the vid all the way to the removal of all components, this is where I ditched my current bezel/housing and reassembled into the newly ordered one. Judging by the assembly, there is no way that a bezel could be replaced without replacing the housing, it's one whole unit, and I very much doubt the build would be that drastically different for the white SGS2.
Some things to note:
Be very careful removing the vibrate motor, the connector and natural pivot point is the weakest part (new module ordered from ebay
If you are transplanting the screen like me, have some adhesive pads in your kit as most tutorials are for new screens, and as can be seen on the vid, these come with pads intact, ready to apply
Try do it in daylight
Hope that helps anyone in a similar situation.
Click to expand...
Click to collapse
Hi, will the heat actually damage the screen? I saw some posts mentioning about putting it into the oven and such. It sounded very intense but if it works without damaging the screen, i might give it a try. Facing the same situation as yours. Scratches and dents all over my front chrome bezel.
So i installed my skinomi screen protector since my other one was scratched and got water under the screen somehow.. Thought it would dry up but it's pretty bad and it's been 24 hours now.. Also there seems to be something wrong and the bottom right of the screen has brighter light coming through in lines. What do i need to replace if i ever choose to get a new screen, a digitizer? I'm not sure what to buy to fix this and any suggestions on where to get a good one. I know the ones on ebay are cheap but i'm afraid they might be bad or something. Any help would be great as this could have been avoided if i didn't use too much solution. Only if i could go back in time....
Try using a blow dryer on low heat near the screen.
I did that, i think i did everything possible. The grey spots probably don't worry me as much because i have a feeling they'll dry out but what's worrying me is the screen seemed to have white lines that are getting bigger and spreading a bit. It's not completely white but it's a lot brighter than other areas. I had to bite the bullet today and use it because of emergency or else i would have let it dry for a few days. I'll take a picture tomorrow afternoon to show what it looks like.
If someone can help i'm planning to open it up and try to clean the screen but if it doesn't get cleaned all the way what would i need to buy to replace it, the LCD screen or a digitizer? I was thinking the LCD because the digitizer is mostly just a glass screen that usually doesn't need replacing unless it's cracked right?
Right, but there's a pretty decent chance you'll crack the digitizer when removing it from the LCD, so you may as well order the complete assembly...should be around $45.
Well i forgot to take a picture today but i'll take one tomorrow of the before and after. I'm receiving my pry and screwdriver set tomorrow and i'll try to clean it before trying to replace this. I'll report how it goes.
uEih said:
Well i forgot to take a picture today but i'll take one tomorrow of the before and after. I'm receiving my pry and screwdriver set tomorrow and i'll try to clean it before trying to replace this. I'll report how it goes.
Click to expand...
Click to collapse
You'll have to be very careful. I was and I still screwed the digitizer trying to clean out some water I had under mine. I ended up having to order a new lcd+digitizer combo.
yareally said:
You'll have to be very careful. I was and I still screwed the digitizer trying to clean out some water I had under mine. I ended up having to order a new lcd+digitizer combo.
Click to expand...
Click to collapse
Yea i did it and was very careful, it wasn't perfect but i didn't crack it or anything, just a little part on the corner that seemed to peel the adhesive off from the digitizer so it looks a bit ugly there. The LCD is completely clean and i cleaned under the digitizer and turned the phone back on but unfortunately it wasn't water in between the digitizer and LCD, the water seemed to be in the LCD so i just went ahead and ordered a new digitizer + LCD combo so they'll be easier to install as a whole than separate.
Apart from all that the screen seemed to have gotten more grey covered on it. I'm not sure if the grey spots are the water marks or the brighter spots because as time passes there are more grey spots covering the screen. Not like it matters anymore.
Also i bought the digitizer + LCD from ebay from hong kong cause it's the cheapest and i feel as if they're manufactured there anyways so there shouldn't be a problem in quality?
Sucks that it had to end up like this, i've never had problems installing wet protectors but i think i'm staying far away from them now...
Hi
My partners phone just took a tumble and has developed a hairline crack across the screen from the front speaker diagonally across the top right corner. The screen still works perfectly so there doesnt seem to be any damage to the lower layers, just the glass. It had a cheap cover on and it has still been damaged.
Now my question is, will this phone survive 2 years of use? We can either try to claim on the insurance as lost / damaged or get a decent case and a screen protector which hopefully would hold the phone together. What do you guys think?
farkkraf said:
Hi
My partners phone just took a tumble and has developed a hairline crack across the screen from the front speaker diagonally across the top right corner. The screen still works perfectly so there doesnt seem to be any damage to the lower layers, just the glass. It had a cheap cover on and it has still been damaged.
Now my question is, will this phone survive 2 years of use? We can either try to claim on the insurance as lost / damaged or get a decent case and a screen protector which hopefully would hold the phone together. What do you guys think?
Click to expand...
Click to collapse
if you drop it its not going to last .
Damaged insurance claim is worth checking on the excess and a self fix screen cost as posted on XDA .
jje
Okay so I am sharing my experience for everyone. I had recently broken my screen, and I needed to replace the screen. I bought a screen digitizer off of eBay, and....Destroyed the phone sub frame. The reason I am posting is because I am warning all of you, you need to buy a full display assembly online. This includes the whole new display( glass and LCD) wires and bits, and a full subframe. Unless you are superior to an Asian 12 year old working in the factory that made your phone (hint hint, wink wink, you're not) than you need to buy a full assembly, or end up like me an destroy your phone.
Sent from my Amazon Kindle Fire HD using Tapatalk HD
+1.
Unfortunately, I saw this post after doing damage to my phone. The plastic housing that the digitizer /lcd sits in is verrrryyy easy to damage around the edges when you try to separate the screen. Heating it with the heat gun to get the separation actually makes it even more fragile and prone to damage. Thankfully I was able to return digitizer/lcd and get full setup from here :
http://www.etradesupply.com/oem-htc-evo-4g-lte-lcd-screen-and-digitizer-assembly-with-front-housing-and-light-guide.html
Hopefully things will go a little better this time.
Wow, that includes the plastic frame? I replaced my screen a couple of weeks ago (glass and LCD), and the edges of the frame did get slightly chewed up. It's not too bad, but I wish I had known abut this item.
On a positive note, I suppose I can get a job in China when the economy completely collapses.
Sent from my Nexus 7 using xda app-developers app
Ya my screen got waterlogged after I got trashed and left it out in the rain. Let everything dry out and thankfully all the boards and connectors work. I ended up going the cheap route and just buying a screen and not the frame. I almost successfully got the thing apart. I do have a small chip in the frame on the left side but my case covers that. I only paid around $50 but I did give myself around $50 in headaches. Definitely spend the extra $50 and just get the whole package.
If you do decide to try and separate the screen from the frame, use a lot of heat. Not necessarily high heat, but for a good duration. Get the adhesive nice and warm. Then pry it loose through one of the holes in the housing/frame (go at it from the back) and slowly work it away from the frame. Once you get it off, heat the adhesive back up and then add some 5 minute quick epoxy to the black adhesive pads in the frame. Then use some clamps and let the epoxy cure. There is a great video I followed below. It took me a while and I will probably ride with this for a minute until it bothers the hell out of me. My gf said she can't even notice.
https://www.youtube.com/watch?v=Ae52Ug8vFwA
case screen cover plastic sheet work?
I'm just wondering how many naked phones get broke compared to well protected?
Gnexd said:
I'm just wondering how many naked phones get broke compared to well protected?
Click to expand...
Click to collapse
I have a Incipio NGP case on mine all the time and I always have a screen protector installed (usually the cheap ones from Amazon). I have never had a problem with the screen until I left my phone out in the rain. The Gorilla Glass II is decently strong but only to a certain extent. I mainly use the screen protector from scratches if I accidentally put it in the same pocket as my keys.
I was afraid of breaking mine one day, fortunately for me my volume button went out first and I have Best Buys insurance and the replace the phone with no deductible.
Seems like screen issues are pretty common on this model. I'm on my 4th Evo now because the screen kept failing on me. Based on what I read it sounds like I'd never want to have to replace this myself.
hi as many note 3 users know, the plastic side frame is easy to get damaged, i have few cracks and one line just under the main power button (not sure just facial or completely crack?)
so, how easy is to change and which one i have to buy ? - im quite noob in hardware sides.
Sure you can buy one on Ebay
I have the same problem, the silver plastic bezel is very fragile.
If you search in Ebay you can found the Bezel and some of them come with tools to turn this in a complete DIY.
Actually i found all the body for this phone in ebay, so you can turn your used and damaged note 3 into a "brand new" one.
Thanks 4 the info. Where did you find it. Could you please share the link?
Thx in advance
hey guys.here is a link for the bezel replacement Bezel On EBAY
i want to tell you that it's not that easy to change it as you need to move the lcd screen from the one bezel to the other one.
there is glue between the lcd and the bezel so you need to warm it and remove it really carefully.i did the process yesterday on my note 3 and it was a pain in the a$$ so i have to tell you to be carefull before any move you re going to do.
Any link for Indian note 3?
Sent from my SM-N900 using XDA Free mobile app
I considered doing this, as I was given a note 3 a while back, but the bezel is beat to hell and the screen had a minor crack. I should've replaced both at the same time, but the small crack turned into a large one and needed immediate attention It's covered by a case now anyway though, so it's not much of an issue anymore.
I dropped mine a while ago and put some pretty nasty scratches on the bezel.
I ended up sanding all the plastic chrome plating off down to the white plastic underneath.
covered the screen with electrical tape and ran a razor round the edge (so I could get to the front part)
It actually looks really good, I prefer it to the chrome.
I got a cheapo battery cover off ebay aswell in orange and it looks real good,
Its a tough job!!!
got my Note 3 as a gift from a friend who cracked it. I replaced the entire Display (along with frame)
and 3 days later I dropped it and got scratches in the frame.
so I decided to buy a frame and fix but its really a tough job.
so I got a bumper for 3$ and job done
I have installed one of those here http://www.ebay.com/itm/Thin-Aluminum-Metal-Bumper-Case-Cover-For-Samsung-Galaxy-Note-3-III-N9000-N9005/151251742076?_trksid=p2045573.c100033.m2042&_trkparms=aid%3D111001%26algo%3DREC.SEED%26ao%3D1%26asc%3D31478%26meid%3D341538ef5e9d4d6da3228a5f902e8cf1%26pid%3D100033%26rk%3D1%26rkt%3D4%26mehot%3Dpp%26sd%3D151251742076
There are some more nicer ones our there, however this does the job well and the build quality is goodd too, my first one at 1,30 USD was not worth anything.
thanks i thought i saw same one for bit less than that, will browse ebay later.
maskerwsk said:
I dropped mine a while ago and put some pretty nasty scratches on the bezel.
I ended up sanding all the plastic chrome plating off down to the white plastic underneath.
covered the screen with electrical tape and ran a razor round the edge (so I could get to the front part)
It actually looks really good, I prefer it to the chrome.
I got a cheapo battery cover off ebay aswell in orange and it looks real good,
Click to expand...
Click to collapse
Photos plz
Up! I'm interested too.
yes i just remember i have some sand paper at home please post photo and detailed instructions... cheers
rockbastard said:
I have installed one of those here http://www.ebay.com/itm/Thin-Alumin...id=100033&rk=1&rkt=4&mehot=pp&sd=151251742076
There are some more nicer ones our there, however this does the job well and the build quality is goodd too, my first one at 1,30 USD was not worth anything.
Click to expand...
Click to collapse
Hows the reception with this frame on it? Bc in the past i bought a cheap one that folds over the original side bezel but reception dropped a lil bit.
triad88 said:
Hows the reception with this frame on it? Bc in the past i bought a cheap one that folds over the original side bezel but reception dropped a lil bit.
Click to expand...
Click to collapse
I haven't noticed any drop in reception at all
rockbastard said:
I haven't noticed any drop in reception at all
Click to expand...
Click to collapse
because you must be either living in the area where your carrier signal is real strong/good, or you dont pay attention to little details, otherwise you're lying
I have tried handful of those and other plastic metalized/mirror painted bumpers and what not and all to one had some impact, especially those which had metalized paint/metal/aluminium back cover.
Simple speed test will tell alot when wearing the cover, or just go and keep an eye on your signal strength meter. It sure as hell affects signal.
mine Note 3 is banged up pretty bad around the bezel but instead I just figured it would be more practical getting some slim neat bumpers and call it a day. not only hiding worn and tired bezel but also protecting the screen and back camera optics to some degree
some of my past purchases that proven to be good investment:
BLACK - http://www.ebay.com/itm/371686423462
BLACK - http://www.ebay.com/itm/331859225625
http://www.ebay.com/itm/271911899853
http://www.ebay.com/itm/391289113353
http://www.ebay.com/itm/151139101488
http://www.ebay.com/itm/181701505005
http://www.ebay.com/itm/182354407036
http://www.ebay.com/itm/311580942819
just thought I will share...
Mr.Ultimate said:
because you must be either living in the area where your carrier signal is real strong/good, or you dont pay attention to little details, otherwise you're lying
I have tried handful of those and other plastic metalized/mirror painted bumpers and what not and all to one had some impact, especially those which had metalized paint/metal/aluminium back cover.
Simple speed test will tell alot when wearing the cover, or just go and keep an eye on your signal strength meter. It sure as hell affects signal.
mine Note 3 is banged up pretty bad around the bezel but instead I just figured it would be more practical getting some slim neat bumpers and call it a day. not only hiding worn and tired bezel but also protecting the screen and back camera optics to some degree
some of my past purchases that proven to be good investment:
BLACK - http://www.ebay.com/itm/371686423462
BLACK - http://www.ebay.com/itm/331859225625
http://www.ebay.com/itm/271911899853
http://www.ebay.com/itm/391289113353
http://www.ebay.com/itm/151139101488
http://www.ebay.com/itm/181701505005
http://www.ebay.com/itm/182354407036
http://www.ebay.com/itm/311580942819
just thought I will share...
Click to expand...
Click to collapse
you have a lot of cases!
erwinsie said:
you have a lot of cases!
Click to expand...
Click to collapse
little too many ... beware that those wooden cases are the coolest thing your phone can get but if you do drop your phone they crack and break apart sometimes... not always though but alot alot sooner than any plastic case would and thats a heartbreaking thing because there not exactly cheap case, but hey - how often does someones phone feels and smells like real fresh quality piece of wood? I like them wooden ones very much even if they crack and put some tax on my pocket at the end of the day its almost like your personal signature of style ... besides, its always warm to touch and zero signal interference
PS: lots more were thrown out many months ago, especially all those metalized ones, no use to me nor could I offer them to anyone I knew who had note 3 due to what they are
When my display was damaged, it got repaired, not only the glass, but the whole display including the bezel, it was 1 piece.. I guess it's very hard to replace only the bezel