hey guys,
now i have a small gameconsole.
my cubot one has lost his IMEIs and i can´t restore them.
i have tried
1. Enter in engenieer mode with : *#*#3646633#*#*
2. Go to Connectivity > CDS Information > Radio Information > Phone 1
3. At "AT+" line add : EGMR = 1,7,"my_first_IMEI_code"
4. Clic on "SEND AT" button below
5. At "AT+" line add a second time : EMGR = 1,10,"my_second_IMEI_code"
6. Clic on "SEND AT COMMAND" button below a second time
7. Reboot phone
8. Verify codes with *#06#* if IMEI codes are ok
Click to expand...
Click to collapse
and in terminal
su
echo 'AT +EGMR=1,7,"IMEI_1"'> /dev/pttycmd1
echo 'AT +EGMR=1,10,"IMEI_2"'> /dev/pttycmd1
Click to expand...
Click to collapse
and i tried MTK Droid Root an Tools 2.4.8 IMEI resoration
and i tried to install the orginal rom
i did not try SP_Flash_Tool_v3.1320.0.174 because i don´t know how to do.
i get messages i don´t know if it´s ok or not.
i have a folder with the following content, made when i rooted my phone.
<DIR> .
<DIR> ..
boot.img
cache.ext4.img
cache.ext4.tar
data.ext4.img
data.ext4.tar
EBR1
EBR2
files.md5
firmware.info
logo.bin
MBR
MT6589_Android_scatter_emmc.txt
nodl_expdb
nodl_misc
nodl_pmt
nodl_protect_f.ext4.tar
nodl_protect_s.ext4.tar
nodl_pro_info
nodl_seccfg
nodl_secro.bin
nvram.bin
phone.info
preloader_and_dsp
recovery.img
system.ext4.img
system.ext4.tar
uboot.bin
userdata_nvram_only.ext4.tar
Click to expand...
Click to collapse
do i have the the abillity to restore my IMEIs?
what is to do?
k guys, here i write down my way to get back my IMEIs.
You Need:
1. Latest or minimum version v3.1320.0.174 of SP Flash Tool
http://chinamobiles.org/downloads.php?do=file&id=864 (if you have a link where you can load allways the latest version write it in this thread. I will add it.)
2. Latest version of MTK Droid Boot & Tools or at minimum version 2.4.8
3. A Backup made with MTK Droid Boot & Tools while rooting
Click to expand...
Click to collapse
Lets do it:
Part One:
1. Start MTK Droid Boot & Tools and go to root, backup, recovery.
2. Press "To prepare Blocks for Flash Tool".
View attachment 2288753
3. Navigate to the folder with your MTK Droid Boot & Tools Backup and select the MD5 file.
View attachment 2288754
4. Wait until job is finished. You will see it in the LOG section of MTK Droid Boot & Tools
View attachment 2288756
5. Your SP Flash Tool compatible Backup will be stored inside a folder of the folder where your MD5 file is.
View attachment 2288755View attachment 2288757
End Part One
Click to expand...
Click to collapse
Part Two:
1. Open SP Flash Tool
2. Tick options -> USB Mode
3. Tick options -> DA Download All -> Battery -> With Battery
View attachment 2288758
4. Load your Scatter file. (Use the Scatterfile from your "!Files_to_FlashTool" folder made by MTK Droid Boot & Tools)
View attachment 2288759View attachment 2288760
If your SEC_RO is checked skip the following text and go directly to 6.
Now you will see most of the entries are checked. Maybe SEC_RO is not checked and now we fix this, because it is very important.
View attachment 2288761
Iin your MTK Droid Boot & Tools backup folder is a file "nodl_secro.bin". This is the same file like secro.img. it has another name because it comes from ext4 filesystem.
5. Tick the SEC_RO entry and use the nodl_secro.bin from your MTK Droid Boot & Tools backup folder.
View attachment 2288762
6. Untick preloader
End Part two
Click to expand...
Click to collapse
Lets bring back your Phone:
1. Remove the Battery from your phone and disconnect your phone from USB
2. Recheck if PRELOADER is UNCHECKED and press "Download"
View attachment 2288763
3. Insert your Battery
4. Plug your USB cable while you press volume up or down hold the button until i write to release (may differ on device (try the other volume button when at 5 nothing happens))
5. SP Flash Tool starts to send data to your phone. You see a red bar and after the red a violet bar at bottom of SP Flash Tool.
6. After the violet bar you see a yellow bar. Now you can release the volume button.
7. When flashing was sucessfull a new smal window with a green circle will pop up.
8. Eat a gummybear. You have deserved.
9. Unplug your USB and remove the Battery, wait 10 seconds and insert your Battery.
10. Start your Phone
Now you should have your IMEIs back and your Phone should work mormal.
Click to expand...
Click to collapse
Maximus1a said:
k guys, here i write down my way to get back my IMEIs.
Lets bring back your Phone:
Click to expand...
Click to collapse
I get to the last part "bring phone back" step 4. SP Flash Tool Does not pick up my device (Nothing happens) i tried volume up and volume down, nothing. Volume Up enters recovery, Volume Down shows me yellow text saying "factory mode" but nothing :/
Edit: PDANet driver installed btw
Maximus1a said:
k guys, here i write down my way to get back my IMEIs.
Lets bring back your Phone:
Click to expand...
Click to collapse
anyone?
lost imei after flashing wrong recovery image
I have a mtk 6589..dualsim..I lost my imei and this guide worked..Got my phone working again..Thank you..
---------- Post added at 11:56 AM ---------- Previous post was at 11:51 AM ----------
Use this guide..Works perfect..
Great!
Maximus1a said:
k guys, here i write down my way to get back my IMEIs.
You Need:
Lets do it:
Lets bring back your Phone:
Click to expand...
Click to collapse
Thanks Dude! you're my saviour..
Thanks for guide
Thank you.
I almost gave up but thanks to you and this guide i managed to get both my imei back.
help
Thank you.. My imei is come back normally like before.
But, i dont know why in my serial number become "12345678abcdef"
I had to trying to change on /sys/sys.info/serial number, save but not changed.
What should i do? Thx before
your serial number is not important. forget about it.
Hi... Can you upload the folder in a zip file.. I need it
bricked my mtk6589 no imei no baseband no recovery image
Can you help my by uploading your recovery image?
Maximus1a said:
k guys, here i write down my way to get back my IMEIs.
You Need:
Lets do it:
Lets bring back your Phone:
Click to expand...
Click to collapse
Hi thanks for this tut. I was just wondering though, why is it important to untick preloader in step 6 if were just going to tick it again on step 1 of Lets bring back your Phone?
hei pal
i just wanna say big thanks to you
now my phone back to normal, i can use it for call
you saved my phone
HELP!!!
Hi guys i need a complete backup for my blu dash 4.5 because i don´t have the secro.inf or ndl_secro.inf file please i need a complete backup for restore my imeis
unbrick MT6575 Chinese dual sim android phone
i accidentally place the wrong boot img in my phone i have all files backed up but in SP flash tool i dont see secro and cache img files coming up so that caused the flash tool to fail periodically, please help me out its my wife's phone
I am trying to unbrick a mtk 6589 device on spflash tools but i keep coming across a BROM ERROR : S_DL_PMT_ERR_NO_SPACE (5069) error, can anyone help with a solution? i would be so grateful.
thanks in adv
Hi. This is a nice tutorial. I'm glad you found a way to fix your IMEI.
I'm on step 3, by the way, and I encountered a problem. My computer seems to not recognize my device when downloading files using SP Flash Tool. I already have the drivers installed (PDANet, mtk VCOM, and Android Universal Drivers) but my device still cannot be detected.
It is detected though when I plug it in using MTK Droid Root and Tools so I'm thinking I have the right drivers installed. It's just that when using SP Flash Tools, it kinda goes under the radar. Do you happen to know why this is?
ouro898 said:
Hi. This is a nice tutorial. I'm glad you found a way to fix your IMEI.
I'm on step 3, by the way, and I encountered a problem. My computer seems to not recognize my device when downloading files using SP Flash Tool. I already have the drivers installed (PDANet, mtk VCOM, and Android Universal Drivers) but my device still cannot be detected.
It is detected though when I plug it in using MTK Droid Root and Tools so I'm thinking I have the right drivers installed. It's just that when using SP Flash Tools, it kinda goes under the radar. Do you happen to know why this is?
Click to expand...
Click to collapse
sorry for the late reply.
are you on windows 8 or 8.1?
until now i never got sp flashtool running correct on 8 or 8.1.
the phone disconnected itself from PC before anything could happen.
Maximus1a said:
sorry for the late reply.
are you on windows 8 or 8.1?
until now i never got sp flashtool running correct on 8 or 8.1.
the phone disconnected itself from PC before anything could happen.
Click to expand...
Click to collapse
I'm on Windows 7, but that happens to me too. The driver shows up in Device Manager, then disappears after about a second. Do I need to install another driver? Am I missing something? Thanks for your reply, by the way.
Related
I've got this new MyPhone A858 Duo, a dual-sim phone with 1Ghz processor from the Philippines.
I've tried rooting it using SuperOneClick 2.3.3.0, UnlockRoot 2.3.1 and Gingerbreak, but it seems that all failed in rooting this new android phone.
Any idea how to root this phone will be greatly appreciated.
TIA
bedodot said:
I've got this new MyPhone A858 Duo, a dual-sim phone with 1Ghz processor from the Philippines.
I've tried rooting it using SuperOneClick 2.3.3.0, UnlockRoot 2.3.1 and Gingerbreak, but it seems that all failed in rooting this new android phone.
Any idea how to root this phone will be greatly appreciated.
TIA
Click to expand...
Click to collapse
I'm bumping this because I'm planning to get the exact the same phone.
Bumping this one as well.
BUMP!
ROOT!!!
Damn, can someone please root or tell how to root this.... Also, I want a new custom ROM..... I WANT IT SO BAAAAD!!!!:highfive::highfive:
Rooting Myphone A858
Bump for this one. Please help us
try using zhuodashi
[SOLVED] rooting a858
1. Install Android USB Driver (PDAnet).
Windows XP/Vista/7 32-bit --- http://pdanet.co/bin/PdaNetA350.exe
Windows Vista/7 64-bit --- http://pdanet.co/bin/PdaNetA350x64.exe
2. Turn off your phone. Then connect your phone via usb data cable.
[ a ] Then an unknown device will appear instantly, it will disappear and then it will reappear. Right click on it and choose to update driver manually. Now locate the folder where your Android MT65xx PreLoader is.
[ b ] Find new software mt65xx preloader. Then choose install the software from a list. Now locate the folder where your Android MT65xx PreLoader is.
NOTE: If nothing happens after plugging then boot to recovery by PRESSING HOLD POWER + VOL UP Button then see your notification area on your desktop then follow either [a] or above.
Done. Now disconnect your phone from the computer. And make it sure that your phone is turned off before proceeding to step 3..
3. Extract downloaded files http://d01.megashares.com/dl/xuN9uOq/SP_Flash_Tool_exe_v2.1140.0.zip to one folder for easy locating of the files. Open SP Flash Tool. Then choose scatter loading. See image below.
http://img833.imageshack.us/img833/6559/78333114.png
4. Look and find the scatter text file http://www.mediafire.com/?y7nd8sd5canxkr5 and open it. See image below.
http://img337.imageshack.us/img337/3639/17602446.png
5. Ignore and tick OK. See image below.
http://img826.imageshack.us/img826/6638/69831501.png
6. Check the box with the name "Recovery". Then look for the downloaded recovery file http://d01.megashares.com/dl/UiC2KlY/recovery.img And open it. See image below.
http://img27.imageshack.us/img27/3097/56761975.png
http://img339.imageshack.us/img339/320/48823847.png
7. Tick Option from the menu and check USB Mode. See image below.
http://img521.imageshack.us/img521/391/48354908.png
8. Tick the Download button. Note: Look at the image carefully before ticking the download button. Make it sure nothing else is checked. See image below
http://img692.imageshack.us/img692/5207/95347966q.png
9. Plug your cellphone via your usb cable. Then wait for it to be finish. See image below.
http://img856.imageshack.us/img856/8315/48740804.png
***NOTE: If your phone isn’t detected after plugging then boot to recovery by PRESSING + HOLD POWER + VOL UP Button THEN go back to step 2.
10. A yellow bar will appear. Wait for it to reach 100%. See image below.
http://img831.imageshack.us/img831/3964/57052207.png
11. Done. Congratulations. You successfully installed a "CUSTOM RECOVERY".
12. Now it's time to root your phone by following the next tutorial below.
MAKE SURE YOU HAVE DONE SUCCESSFULLY THE STEPS ABOVE BEFORE PROCEEDING BELOW
1. Copy and paste root_MP858Duo.zip http://d01.megashares.com/dl/tPWGVHo/root_MP858Duo.zip to the root of your SD Card.
2. Turn Off your phone and open custom recovery by pressing and holding Power Button + Volume Up.
3. Install zip from sdcard.
4. Choose zip from sdcard.
5. Choose root_MP858Duo.zip. Then confirm update.
6. Reboot.
7. Look for an icon with an Android Face named "SuperUser".
8. Done. Congratulations. Your phone is now rooted.
Does Not Work
isfahan27 said:
1. Install Android USB Driver (PDAnet).
2. Turn off your phone. Then connect your phone via usb data cable.
...
Click to expand...
Click to collapse
I've heard this works for other people. With my phone it doesn't. When I plug it in, it doesn't show an unknown device. I've already downloaded and installed MT65xx Preloader and tried out a VCom, but still nothing. I've been going at it for a week, so if anyone's got an answer, advice would be great. Thanks!
Error # 16008
A message came out,
"EBOOT ERROR (16008), [Android] Partition size changed!
[HINT]:
Partial images download error.
The following partitions must be downloaded FULL altogether."
I followed all the steps (and the links) up until I clicked the 'Download' button. :/ When I click download button, that message shows.
I have: My Phone A858, Android 2.3.2 (Gingerbread), Sony Vaio with a Windows 7. Thanks!
Rooting
outerspacekaloy said:
A message came out,
"EBOOT ERROR (16008), [Android] Partition size changed!
[HINT]:
Partial images download error.
The following partitions must be downloaded FULL altogether."
I followed all the steps (and the links) up until I clicked the 'Download' button. :/ When I click download button, that message shows.
I have: My Phone A858, Android 2.3.2 (Gingerbread), Sony Vaio with a Windows 7. Thanks!
Click to expand...
Click to collapse
ok sir.... :good:
one click to root
Hi,
there is a simple way is using one root click.
Try this : http://360dmobile.com/root-1-85-one-click-root-act-now-may-not-last-foreve/
bedodot said:
I've got this new MyPhone A858 Duo, a dual-sim phone with 1Ghz processor from the Philippines.
I've tried rooting it using SuperOneClick 2.3.3.0, UnlockRoot 2.3.1 and Gingerbreak, but it seems that all failed in rooting this new android phone.
Any idea how to root this phone will be greatly appreciated.
TIA
Click to expand...
Click to collapse
You try this video on youtube, because A858 Duo is also Q-Smart S15
http://www.youtube.com/watch?v=BImmgu0-kR0
Download all neccessary things below the video on youtube to root
Good luck!
I read the post on http://forum.xda-developers.com/showthread.php?t=2380700 but it is not working...:crying::crying:
Firstly I was having SamFlare V5 installed on my phone with CWM 6.0.3.0 then i tried to update to CWM 6.0.4.4 which was not working then again i replaced with older one. Now SIM cards are not getting detected and SIM MANAGEMENT from settings in disabled and when i checked in ENGINEERING MODE in CDS INFORMATION i found that RADIO is TURNED OFF...
Then i tried to install Canvas 4 Stock ROM but same problem persists...:crying::crying::crying:
Plz Help!!!
TIA...
nimishshah1508 said:
I read the post on http://forum.xda-developers.com/showthread.php?t=2380700 but it is not working...:crying::crying:
Firstly I was having SamFlare V5 installed on my phone with CWM 6.0.3.0 then i tried to update to CWM 6.0.4.4 which was not working then again i replaced with older one. Now SIM cards are not getting detected and SIM MANAGEMENT from settings in disabled and when i checked in ENGINEERING MODE in CDS INFORMATION i found that RADIO is TURNED OFF...
Then i tried to install Canvas 4 Stock ROM but same problem persists...:crying::crying::crying:
Plz Help!!!
TIA...
Click to expand...
Click to collapse
Watch this video tutorial - http://youtube.com/watch?v=8ZEVDwcCVzY
Sent from my Micromax A116 using XDA Premium 4 mobile app
RE:
I have watched this video and tried same but problem is in his case the radio is on but in my case radio is off and sim state is also not ready as shown in previously attached image!!! and while typing list box is not also opening and when i click on send AT command android will toast "AT command is failed to send"
RE:
I have watched this video and tried same but problem is in his case the radio is on but in my case radio is off and sim state is also not ready as shown in previously attached image!!! and while typing list box is not also opening and when i click on send AT command android will toast "AT command is failed to send"
[solved] radio off problem in mtk devices
hi, atlast i have found a solution of the "radio off" problem. It will definitely work...........just follow my instructions............
1. First of all you need to have the stock rom for your phone which you can easily find by googling.
2. Now run the sp flash tool in your pc.
3. click on the "scatter loading" botton and select the .txt file by browsing your downloaded stock rom.
4. Now click the "format" option on top of the flash tool.
5. Now switch off your phone and connect it to your pc via usb cable and press the up/down volume bottons for detecting.
6. once detected, your phone will be formatted.
7. now disconnect your phone from pc and close the sp tool. Then repeat the steps from 2 to 3.
8. Now click on the "download" option on top of the sp flash tool.
9. and again connect your phone and make it detected in the same process described earlier.
10. once the flashing is completed you will see a green o .
11. now disconnect your phone and switch it on, and the radio of your phone will be turned on.
12. also you need to rewrite the imei nos going to engineer mode by simply dialing *#3646633#*#*
Guys, I worked hard to find this solution so, if this process works please make a little donation to my sbi account 30449335478
Can you made back up of your IMEI ? Onceday I Already Same Question.before doing anythings.fortunately i backed up my IMEI.So if You not backed up.then no answer for your questions.
Puspendu said:
hi, atlast i have found a solution of the "radio off" problem. It will definitely work...........just follow my instructions............
1. First of all you need to have the stock rom for your phone which you can easily find by googling.
2. Now run the sp flash tool in your pc.
3. click on the "scatter loading" botton and select the .txt file by browsing your downloaded stock rom.
4. Now click the "format" option on top of the flash tool.
5. Now switch off your phone and connect it to your pc via usb cable and press the up/down volume bottons for detecting.
6. once detected, your phone will be formatted.
7. now disconnect your phone from pc and close the sp tool. Then repeat the steps from 2 to 3.
8. Now click on the "download" option on top of the sp flash tool.
9. and again connect your phone and make it detected in the same process described earlier.
10. once the flashing is completed you will see a green o .
11. now disconnect your phone and switch it on, and the radio of your phone will be turned on.
12. also you need to rewrite the imei nos going to engineer mode by simply dialing *#3646633#*#*
Guys, I worked hard to find this solution so, if this process works please make a little donation to my sbi account 30449335478
Click to expand...
Click to collapse
Great work. My problem solved :good:
Puspendu said:
hi, atlast i have found a solution of the "radio off" problem. It will definitely work...........just follow my instructions............
1. First of all you need to have the stock rom for your phone which you can easily find by googling.
2. Now run the sp flash tool in your pc.
3. click on the "scatter loading" botton and select the .txt file by browsing your downloaded stock rom.
4. Now click the "format" option on top of the flash tool.
5. Now switch off your phone and connect it to your pc via usb cable and press the up/down volume bottons for detecting.
6. once detected, your phone will be formatted.
7. now disconnect your phone from pc and close the sp tool. Then repeat the steps from 2 to 3.
8. Now click on the "download" option on top of the sp flash tool.
9. and again connect your phone and make it detected in the same process described earlier.
10. once the flashing is completed you will see a green o .
11. now disconnect your phone and switch it on, and the radio of your phone will be turned on.
12. also you need to rewrite the imei nos going to engineer mode by simply dialing *#3646633#*#*
Guys, I worked hard to find this solution so, if this process works please make a little donation to my sbi account 30449335478
Click to expand...
Click to collapse
Really thank u man, i had this problem with my bq e5 fhd and now solve it. Thank u!!!!! Greetings from spain!!
radio of zenfone 2 laser fix
i have zenfone 2 laser wich radio was off i cannot turn on radio please help
Puspendu said:
hi, atlast i have found a solution of the "radio off" problem. It will definitely work...........just follow my instructions............
1. First of all you need to have the stock rom for your phone which you can easily find by googling.
2. Now run the sp flash tool in your pc.
3. click on the "scatter loading" botton and select the .txt file by browsing your downloaded stock rom.
4. Now click the "format" option on top of the flash tool.
5. Now switch off your phone and connect it to your pc via usb cable and press the up/down volume bottons for detecting.
6. once detected, your phone will be formatted.
7. now disconnect your phone from pc and close the sp tool. Then repeat the steps from 2 to 3.
8. Now click on the "download" option on top of the sp flash tool.
9. and again connect your phone and make it detected in the same process described earlier.
10. once the flashing is completed you will see a green o .
11. now disconnect your phone and switch it on, and the radio of your phone will be turned on.
12. also you need to rewrite the imei nos going to engineer mode by simply dialing *#3646633#*#*
Guys, I worked hard to find this solution so, if this process works please make a little donation to my sbi account 30449335478
Click to expand...
Click to collapse
Man many thanks for your post finally got it working
Hi all. I will try to write an tutorial for all who want to root your new update firmware.
First lets consider that you have updated your firmware and booted at least one time.
Now what we need is: one PC,cable to conect your phone to PC, and 2 tools: TWRP 2.7.1.1 for KK and Superuser or SuperSU at least 2.16, no less.
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip or SuperSU on your SDCARD. Remember: only one is good. DO NOT FLASH BOTH. Flash the one you like.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 or the newest one TWRP 2.8.4.0 rev 2 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119 or SP_Flash_Tool_v5.1352.01. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum in SP Flash Tool v3. In SP Flash Tool v 5 dont need. They are allready selected. Recovery.img should appear checked.
10.1. I have updated the post with some custom scatter files for 4GB and 8GB Firmware. Iff you get diferent errors when you flash the recovery file use this custom scatter files.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Then boot directly to recovery your phone by pressing power with vol + and vol - butons together. Not Optional!
15. From TWRP flash Superuser.zip or SuperSU 2.xx. SuperSU is fixed. Works fine now.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Hope this helped. For me worked with no mistake.
Waiting for feedback.
Update:
I have uploaded TWRP Corrected by Javum. Thanks Javum. And it is working on ROW 226 and 227 tested personaly by installing patches, superuser and making backups.
Sent from my Lenovo P780
SP Flash Tool_v.3 and v.5
stympy said:
Hi all. I will try to write an tutorial for all who want to root your new update firmware.
First lets consider that you have updated your firmware and booted at least one time.
Now what we need is: one PC,cable to conect your phone to PC, and 2 tools: TWRP 2.7.1.1 for KK and Superuser.
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have the latest FlashTool.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Hope this helped. For me worked with no mistake.
Waiting for feedback.
Sent from my Lenovo P780 using LiFe v.07 and TWRP 2.6.3.0.
Click to expand...
Click to collapse
This method did not work i got this error
"pmt changed for the rom it must be downloaded"
astrokid1993 said:
This method did not work i got this error
"pmt changed for the rom it must be downloaded"
Click to expand...
Click to collapse
Try to use Firmware Upgrade buton.
Or: You need to edit the file MT6589_Android_scatter_emmc.txt section USRDATA 0x48d80000 on USRDATA 0x58980000.
Waiting for feedback.
Sent from my Lenovo P780 using LiFe v.07 and TWRP 2.6.3.0.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Point no 12 doesn't work with me, Anything I should know?
asambe2dumb said:
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Point no 12 doesn't work with me, Anything I should know?
Click to expand...
Click to collapse
If the 12 point doesn't work it means that you don't have the driver installed or installed correctly. Check the drivers.
Sent from my Lenovo P780 using XDA Free mobile app
all steps are done but not succsses
Hallo... IN my lenovo p780 with officaly updated android 4.4.2 and not rooted phone .I fallow all steps carrectly as u discribed after press download button when I connect my switched off phone I got mtp error than I edit scatter file user data as describe in comment section after that I press download and connect my p780 switched of all process done smuthaly I got green circles that's mean I am done after that I switched on phone and switched off phone for boot in recovery I press vol+ vol- and power buttons but their is not twrp recovery option ..only stock recovery option .
Pls help bro ...what I am doing wrong?. Or any other way to do this ?
Thanks for this wonderful tutorial.
Hi all. I will try to write an tutorial for all who want to root your new update firmware.
First lets consider that you have updated your firmware and booted at least one time.
Now what we need is: one PC,cable to conect your phone to PC, and 2 tools: TWRP 2.7.1.1 for KK and Superuser.
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder  )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Hope this helped. For me worked with no mistake.
Waiting for feedback. 
Update:
I have uploadet TWRP Corrected by Javum. Thanks Javum. And it is working on ROW 221 tested personaly by installing patches, superuser and making backups.
Sent from my Lenovo P780 using LiFe v.07 and TWRP 2.6.3.0.
Sent from my Lenovo P780 using XDA Free mobile app
I have not rooted lenovo p780 official updated to android 4.4.2 s221 OK I want root my phone I try every thing like pharma root. One click root ;rescue root;vroot ;kingoroot;and many other which I don't remember but not success ..OK than I try to follow your method ...first when I connect my switched off phone downloading process start after red bar complete I got mtp error
Then I edit scatter file user data section as u mansion in comments sections after that download has done withouts error I got green circle that's mean I am done ... OK I disconnect phone from computer and power on than switched off for boot in recovery ... I press power button + vol up and down together but their is ...
NOT TWRP RECOVERY .. only stock android recovery huuh what I do now ..where I am wrong any suggestion plz help
And thanks for this wonder full tutorial.
pu04 said:
Hi all. I will try to write an tutorial for all who want to root your new update firmware.
First lets consider that you have updated your firmware and booted at least one time.
Now what we need is: one PC,cable to conect your phone to PC, and 2 tools: TWRP 2.7.1.1 for KK and Superuser.
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder  )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Hope this helped. For me worked with no mistake.
Waiting for feedback. 
Update:
I have uploadet TWRP Corrected by Javum. Thanks Javum. And it is working on ROW 221 tested personaly by installing patches, superuser and making backups.
Sent from my Lenovo P780 using LiFe v.07 and TWRP 2.6.3.0.
Sent from my Lenovo P780 using XDA Free mobile app
I have not rooted lenovo p780 official updated to android 4.4.2 s221 OK I want root my phone I try every thing like pharma root. One click root ;rescue root;vroot ;kingoroot;and many other which I don't remember but not success ..OK than I try to follow your method ...first when I connect my switched off phone downloading process start after red bar complete I got mtp error
Then I edit scatter file user data section as u mansion in comments sections after that download has done withouts error I got green circle that's mean I am done ... OK I disconnect phone from computer and power on than switched off for boot in recovery ... I press power button + vol up and down together but their is ...
NOT TWRP RECOVERY .. only stock android recovery huuh what I do now ..where I am wrong any suggestion plz help
And thanks for this wonder full tutorial.
Click to expand...
Click to collapse
By any chance is your phone made in 2014 ?
Then if it is use preloader. Check preloader and try this one.
Its one year old phone ..with jelly bin 4.2.2 now I updated to 4.4.4 originally by ota ..I want to root it actually in mtk toot its show this massage `` ATTENTION! File /system/recovery-from-boot.p which restore factory recovery in case of phone switching on in a normal mode Is Found!
I don't know but I think its affect ..can u pls explain it what's this mean.
Thanks for reply ...I try with bootloder next day
Sent from my Lenovo P780 using XDA Free mobile app
Will it work on S214 also or should i instal S221 for my phone
astrokid1993 said:
Will it work on S214 also or should i instal S221 for my phone
Click to expand...
Click to collapse
For me worked on both.
Sent from my Lenovo P780
Thanksgiving
OK....FIRST I HEARTILY THANKS TO U ..NOW I AM SUCCESS ..finally rooted my lenovo p780 4.4.2 KitKat updated phone ..without any error or bricking my phone .. Thanks for this wonder full tutorial ..
As I mentioned previous reply that I got error from Sp flash tool ..something pmt error ..than as u sugest i edit user data section in scatter data section and flash it ..but nothing happen their is only stock recovery .. Today i retry process ..
1- follow all steps as it is
2 - for pmt error change user data section 3- at last u advise that power on phone then reboot in recovery by pressing volume+'- +power button at this stage ..what I have done ..is
I don't on my phone ..after flashing recovery I direct go to recovery using power + volume up+ volume down ..and waaaala here is done I got twrp custom recovery .. But don't flase superuser .zip just shutdown phone and on go to normal mode and check every thing is fine ..now power off go to recovery ...there is twrp present ..in recovery install super user ..just unchake verify check mark its install without any error ..and ..GOT ROOTED ..
Conclusion - why I unsuccessful in first time I don't know but think..I have this type of file .. File /system/recovery-from-boot.p which restore factory recovery in case of phone switching on in a normal mode Is Found! I think its prevent twrp when I normally switch on phone ..so this time I don't on phone go to direct recovery and all is done .. I got custom recovery..
AT last I thank you again for this great tut. Its worked for me finally .
Sent from my Lenovo P780 using XDA Free mobile app
stympy said:
Hi all. I will try to write an tutorial for all who want to root your new update firmware.
First lets consider that you have updated your firmware and booted at least one time.
Now what we need is: one PC,cable to conect your phone to PC, and 2 tools: TWRP 2.7.1.1 for KK and Superuser.
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Hope this helped. For me worked with no mistake.
Waiting for feedback.
Update:
I have uploadet TWRP Corrected by Javum. Thanks Javum. And it is working on ROW 221 tested personaly by installing patches, superuser and making backups.
Sent from my Lenovo P780 using LiFe v.07 and TWRP 2.6.3.0.
Click to expand...
Click to collapse
Friend, first time I follow all your steps to install TWRP , but it failed . And I see your reply in this thread and change the USR DATA . But it failed again , MY PHONE WAS BRICKED !!!!! IT DONT DO ANY RESPONSE , CANT POWER ON , CANT CONNECT TO COMPUTER , CANT GO TO RECOVERY . IT ONLY SHOW A RED LIGHT WHEN CHARGING . HOW TO SOLVE THIS PROBLEM ??? PLEASE HELP ME ...
stympy said:
Hi all. I will try to write an tutorial for all who want to root your new update firmware.
First lets consider that you have updated your firmware and booted at least one time.
Now what we need is: one PC,cable to conect your phone to PC, and 2 tools: TWRP 2.7.1.1 for KK and Superuser.
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Reboot at least once. Then reboot to recovery by powering off your phone and restart with vol + - and power butons pressed.
15. From TWRP flash Superuser.zip.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Hope this helped. For me worked with no mistake.
Waiting for feedback.
Update:
I have uploadet TWRP Corrected by Javum. Thanks Javum. And it is working on ROW 221 tested personaly by installing patches, superuser and making backups.
Sent from my Lenovo P780 using LiFe v.07 and TWRP 2.6.3.0.
Click to expand...
Click to collapse
Not working at all for me i did everything correctly till point 11 when i connect my phone as in point 12 my phone starts charging and nothing is getting detected in the sp flash tool.
Any one please help me with my problem
tngultimate said:
Friend, first time I follow all your steps to install TWRP , but it failed . And I see your reply in this thread and change the USR DATA . But it failed again , MY PHONE WAS BRICKED !!!!! IT DONT DO ANY RESPONSE , CANT POWER ON , CANT CONNECT TO COMPUTER , CANT GO TO RECOVERY . IT ONLY SHOW A RED LIGHT WHEN CHARGING . HOW TO SOLVE THIS PROBLEM ??? PLEASE HELP ME ...
Click to expand...
Click to collapse
Your phone seems to be produced in 2014. For this phones must do this:
1. Must flash with another preloader.
Look for this ROM : P780_S136_140306_Lang.7z
Flash this Rom then OTA update.
Then tell me if it works.
Sent from my Lenovo P780
astrokid1993 said:
Not working at all for me i did everything correctly till point 11 when i connect my phone as in point 12 my phone starts charging and nothing is getting detected in the sp flash tool.
Any one please help me with my problem
Click to expand...
Click to collapse
Did you installed the drivers?
Did you presed the firmware upgrade first and then plugged the phone?
Update
Try this:
Press Download and open the case of your phone and press the little red buton for 2 seconds.
Sent from my Lenovo P780
stympy said:
Did you installed the drivers?
Did you presed the firmware upgrade first and them plugged the phone?
Sent from my Lenovo P780
Click to expand...
Click to collapse
I installed driver already... My phone now cant do anything... Help me please ...
tngultimate said:
I installed driver already... My phone now cant do anything... Help me please ...
Click to expand...
Click to collapse
Hi.
Do not panic. Your phone is just soft bricked.
Here is the link to download what you must flash first:
https://drive.google.com/folderview?id=0B2ORIgaV4iacT01mTm5JVzFuRGs&usp=sharing
And now here's a little tutorial how to save your phone. You should respectit exactly.
Step by step you will do this:
>>>>> USE WINDOWS 7 FOR THIS TUTORIAL <<<<<<<<<<<
>>>>>>>>>>REMOVE THE USB CALBLE FROM PHONE! <<<<<<<<<<<<<
NOW:
-Lets consider that you have downloadet the firmware
1. Unpack ROM, and Click on Flash_tool.exe
2. Select a the MT6589_Android_scatter_emmc.txt in ROM from target_bin folder
3. Wait file to be added into Flash Tool
4. Choose Options->USB Model,click USB Model SKIP THIS STEP IFF SELECTED
5. Choose Option->DA DownLoad All->Speed->High Speed, click High Speed
6. Check box with DA DL All With Check Sum
7. Turn off your phone - skip this step is allready powered off
8. "Press Firmware->Upgrade "
9. And ONLY NOW connect your phone into the computer via USB data cable.
10. The process will start and a red progress bar will appear after color purple, yellow.
OR
11. If the step 9 dont work open the case of your phone and you will find a red small buton and press it 2 seconds.
12. The process will start and a red progress bar will appear after color purple, yellow.
13. And green circles display
- Finish !
- You can now safely disconnect your phone and turn it on!
After this tell me iff something goes wrong !
stympy said:
Hi.
Do not panic. Your phone is just soft bricked.
Here is the link to download what you must flash first:
https://drive.google.com/folderview?id=0B2ORIgaV4iacT01mTm5JVzFuRGs&usp=sharing
And now here's a little tutorial how to save your phone. You should respectit exactly.
Step by step you will do this:
>>>>> USE WINDOWS 7 FOR THIS TUTORIAL <<<<<<<<<<<
>>>>>>>>>>REMOVE THE USB CALBLE FROM PHONE! <<<<<<<<<<<<<
NOW:
-Lets consider that you have downloadet the firmware
1. Unpack ROM, and Click on Flash_tool.exe
2. Select a the MT6589_Android_scatter_emmc.txt in ROM from target_bin folder
3. Wait file to be added into Flash Tool
4. Choose Options->USB Model,click USB Model SKIP THIS STEP IFF SELECTED
5. Choose Option->DA DownLoad All->Speed->High Speed, click High Speed
6. Check box with DA DL All With Check Sum
7. Turn off your phone - skip this step is allready powered off
8. "Press Firmware->Upgrade "
9. And ONLY NOW connect your phone into the computer via USB data cable.
10. The process will start and a red progress bar will appear after color purple, yellow.
OR
11. If the step 9 dont work open the case of your phone and you will find a red small buton and press it 2 seconds.
12. The process will start and a red progress bar will appear after color purple, yellow.
13. And green circles display
- Finish !
- You can now safely disconnect your phone and turn it on!
After this tell me iff something goes wrong !
Click to expand...
Click to collapse
Thanks for replying But my phone cant connect to computer... My computer keep saying my phone is malfunction...
tngultimate said:
Thanks for replying But my phone cant connect to computer... My computer keep saying my phone is malfunction...
Click to expand...
Click to collapse
Can you tel me what your computer says more exacly ?
Hi...
from mr stympy thread...
stympy said:
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip or SuperSU on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119 or SP_Flash_Tool_v5.1352.01. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
10.1. I have updated the post with some custom scatter files for 4GB and 8GB Firmware. Iff you get diferent errors when you flash the recovery file use this custom scatter files.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
13. After this you should have custom recovery TWRP installed.
14. Then boot directly to recovery your phone by pressing power with vol + and vol - butons together. Not Optional!
15. From TWRP flash Superuser.zip or SuperSU 2.45. SuperSU is fixed. Works fine now.
16. Voila you have your KitKat rooted.
17. Now go to Magazin Play and download an RootChecker app and verify.
Click to expand...
Click to collapse
item no.1: don't know if it installed correctly, but i can copy the superuser.zip unto my sdcard
item no.6: using spflash tools ver. v3.1344.0.212 that mr stympy personally gave me...
at item no.12 : 100% completed but no green circle appeared....:crying:
snapshot : imgur.com/6OCfkwM
my phone is still connected to the pc and sp flash tool because afraid of bricking it....:crying: please help:crying:
blkxiicat said:
Hi...
from mr stympy thread...
item no.1: don't know if it installed correctly, but i can copy the superuser.zip unto my sdcard
item no.6: using spflash tools ver. v3.1344.0.212 that mr stympy personally gave me...
at item no.12 : 100% completed but no green circle appeared....:crying:
snapshot : imgur.com/6OCfkwM
my phone is still connected to the pc and sp flash tool because afraid of bricking it....:crying: please help:crying:
Click to expand...
Click to collapse
Disconnect your phone and if is not starting press the small red button for 20 secconds.
Keep me informed!
stympy said:
Disconnect your phone and if is not starting press the small red button for 20 secconds.
Keep me informed!
Click to expand...
Click to collapse
ok, managed to boot the phone, but when got to home screen it says that my date is wrong....(1/1/2010).
auto-sync with network time....my date and time is back to normal...
shut down the phone (i didn't press the red button) and try to reboot into recovery (power+volumeup+volumedown)
............no twrp, i think (maybe stock recovery mode... some china word with android mascot as background...)
fortunately my phone was not bricked... but no twrp either.....so what is the problem..
thanks.
blkxiicat said:
ok, managed to boot the phone, but when got to home screen it says that my date is wrong....(1/1/2010).
auto-sync with network time....my date and time is back to normal...
shut down the phone (i didn't press the red button) and try to reboot into recovery (power+volumeup+volumedown)
............no twrp, i think (maybe stock recovery mode... some china word with android mascot as background...)
fortunately my phone was not bricked... but no twrp either.....so what is the problem..
thanks.
Click to expand...
Click to collapse
Use version 5 of TWRP!
stympy said:
Use version 5 of TWRP!
Click to expand...
Click to collapse
hmm....
stympy said:
Originally Posted by stympy
Lets begin.
1. Connect your phone to your PC and install phone drivers correctly.
2. Copy superuser.zip or SuperSU on your SDCARD.
3. Disconnect your phone from PC.
4. Extract files from TWRP 2.7.1.1 archive on some folder on your PC.(Remember the folder )
5. In your folder that you extracted your archive you should find recovery.img and one scatter file.
6. Now you must have this FlashTool - SP_Flash_Tool_v3.1304.0.119 or SP_Flash_Tool_v5.1352.01. Not Optional.
7. Power Off your phone.
8. After power off your phone open FlahTool and browse for the scatter file your folder where are the recovery.img and scatter file.
9. Now comes the tricky part .
10. Load the scatter file and mark DA DL with check sum. Recovery.img should appear checked.
10.1. I have updated the post with some custom scatter files for 4GB and 8GB Firmware. Iff you get diferent errors when you flash the recovery file use this custom scatter files.
11. Press Download NOT FIRMWARE UPGRADE.
12. Now, just now plug the cabble on your phone. Download should start and a green circle should appear.
Click to expand...
Click to collapse
point no.10 does not appear in ver. 5 sp flash tools....is it okay?
blkxiicat said:
hmm....
point no.10 does not appear in ver. 5 sp flash tools....is it okay?
Click to expand...
Click to collapse
In version 5 it automaticaly selected, to avoid any mistake.
Hi Poco x3 gt brick please help me!
Copied from another post, works for me
Hello! (Read it fully)
I had the same problem, but i finally got it. First download the 12.5.7.0 rom from this page (Fastboot rom)
Xiaomi Poco X3 GT (chopin) Stock Firmware Collections
On this page, we will share all the latest Xiaomi Poco X3 GT (codenamed chopin) firmware flash files. To flash the firmware file, you need Xiaomi Mi Flash
www.getdroidtips.com
Then, go to Mi Flash Tool (also download from that page). The version you need is 20210226
Then unzip the rom as many times as it needs, and copy it (the most decompressed folder) to the desktop. Then, launch Mi Flash tool and install the drivers in drivers page. In the right corner you need to select "Clean all". And.... FLASH!
It solved my problem. I had the same as you. If your computer doesn't recognize your device, stay in fastboot 30 minutes and it will turn off automatically (with usb unplugged) or if it says no digest file found, turning off in 5 seconds turn it off.
I hope this can solve your problem.
Edit: Then update the firmware to 12.5.8.0 OTA way. Don't obey people saying stupidities like "Buy a new one". This is a forum, to help people, and if u don't know the solution, DON'T SAY ANYTHING
Bye
download mtk bypass tool and spflashtoll , install mtk preloader driver , open mtk bypass tool and spflash tool , open scatter file from folder image( from unziped fastboot firmware folder), then click disable auth from bypass tool and put the device and hold vol up + vol down , when seccus click download from spflashtool good luck
Welp. here's my take on how i did it.
Download All Links here:
SP Flash Tool: https://mega.nz/file/G4VnxTKa#_uq8YdL3VS-ilO_cVIDv2zb4RRiVwCgnLlK_xS4uJo8
MTK META Utility: https://mega.nz/file/u4cwzRgL#n15IAtntMiPz_W2wB1Yb6j8yXvb86V2dzLesT6nOnnY
POCO X3 GT Original Firmware + Tutorial: https://romprovider.com/poco-x3-gt-firmware-support/
(MEGA Links are mine for easy download and no corruption)
Download the firmware first before the tools
After downloading all the files above, do this
1. Extract the firmware into your desktop
2. Extract SP Flash Tool into your desktop
3. Run SP Flash Tool and MTK META UTILITY
4. On SP Flash Tool, Locate for Scatter Loading file
View attachment 5632675
Press Choose
5. Locate the scatter file in your extracted firmware
View attachment 5632677
SP Flash Tool will Look like this
View attachment 5632681
6. Run MTK META UtilityView attachment 5632683
7. Press "Disable Auth
View attachment 5632685
8. Long press VOL Up And connect to pc (Check Device Manager Until you see Mediatek USB Port (COMx). If you didn't see it, Download the Mediatek Drivers: https://androidfilehost.com/?w=files&flid=216849 )
If it detected, It will say this on logs:
View attachment 5632687
9. Press Download (NOTE: Just select DOWNLOAD ONLY. DO NOT SELECT "FORMAT-DOWNLOAD" or your IMEI and MAC ADDRESS WILL BE GONE FOREVER!!!)
View attachment 5632689
have some coffee while flashing
If it succeeded, the OK Window will POPUP
View attachment 5632691
Long press power button to reboot until the poco logo shows up. It will reboot to FASTBOOT (aka. Bootloader)
While you're at it and if you have platform_tools,
10. Copy contents in platform tools and transfer to the firmware folder (or copy the insides of the firmware folder and paste it in platform_tools folder)
it will look like this
View attachment 5632693
(don't mind the gms.apk cause i accidentally added there but there's no gms.apk on yours)
11. Run flash_all.bat and wait until the phone reboots.
if it rebooted, it should've reboot to miui.
that's how i restored my phone.
pls reply if it works to you too...
Hello, I need help after pressing download in sp flash after a few seconds of the following error message:
Luizinho22 said:
Hello, I need help after pressing download in sp flash after a few seconds of the following error message:
Click to expand...
Click to collapse
try flashing one by one
https://www.google.com/url?sa=t&source=web&rct=j&url=https://m.youtube.com/watch%3Fv%3DdbItjjjXwdk&ved=2ahUKEwizn5PGo6T4AhVFRmwGHQtIB_sQwqsBegQIBRAD&usg=AOvVaw1crzkjvWepJYX8dBLp6njt
No, error continued
Luizinho22 said:
Hello, I need help after pressing download in sp flash after a few seconds of the following error message:
Click to expand...
Click to collapse
oh. i'll research
Ok
Luizinho22 said:
No, error continued.
Click to expand...
Click to collapse
is your device global? or your device is just bootloader locked???
Global
the bootloader is blocked
Luizinho22 said:
the bootloader is blocked
Click to expand...
Click to collapse
if your bootloader is locked, you can't do anything... unless if you find a fix
Luizinho22 said:
Hello, I need help after pressing download in sp flash after a few seconds of the following error message:
Click to expand...
Click to collapse
worked for me same model , flash one by one , after flashing one then unchek it and go for the next one ,skip the ones with errors , keep going to the last one , when finish close and disconect ,now you should be able to enter fastboot mode, and now go to mi flash tool, and flash the official global rom ,it should be succed and boot your phone