Ok so I installed the Chucke Rom and the Radio thing for my phone and now it is in an infinite loop when it boots up. It doesn't turn on when I don't have it charged in and when I do have the phone charged in, the Chucke Rom thing loads up the custom boot logo but then the screen goes black and does the same thing over again. This is a serious help needed because I really need my phone. Can anyone help me out here?
Boozor said:
Ok so I installed the Chucke Rom and the Radio thing for my phone and now it is in an infinite loop when it boots up. It doesn't turn on when I don't have it charged in and when I do have the phone charged in, the Chucke Rom thing loads up the custom boot logo but then the screen goes black and does the same thing over again. This is a serious help needed because I really need my phone. Can anyone help me out here?
Click to expand...
Click to collapse
u sure u put the rite radio on ur phone ?
Do you have a tmous hd2? Did you flash a compatible radio? Were there any issues encoutered when flashing? Have you tried a task29 yet?
boot loop = bent battery pin
Boozor said:
Ok so I installed the Chucke Rom and the Radio thing for my phone and now it is in an infinite loop when it boots up. It doesn't turn on when I don't have it charged in and when I do have the phone charged in, the Chucke Rom thing loads up the custom boot logo but then the screen goes black and does the same thing over again. This is a serious help needed because I really need my phone. Can anyone help me out here?
Click to expand...
Click to collapse
connect your phone to your pc, while its off hold the volume down key and switch it on, without releasing the volume down key, then it will enter bootloader mode, from dere go on your pc and reflash the rom.
if u still cant enter bootloader mode then hold the volume down key while your phone is on, when that chucky rom screen comes up just press the red reset button which is located at the back of your phone, u need to remove the back cover to see it, so u press the reset button while holding the volume down key and wait til the bootloader screen appears, then you can just reflash your rom, thats what i done
Well I was undervolting and underclocking my i9100 for a few months and it would suffer from freezes and stuff like that nothing much as I would be able to perform a hard reset and reboot with my phone completely working everytime that happens. However today, I just locked my phone after taking a picture and I could not unlock it after that. I pressed the power button and home button but the screen would not turn on. So i just took out the battery and tried booting the phone. It was stuck in a bootloop where the boot animation would just keep on playing. So i force shutdown it and booted it into recovery. I had CWM 6.0.4.6 installed and when i booted into recovery, it gave me the message it cannot mount something and cannot load last kmsg and blah. I took no notice and tried to format cache. During this point, the recovery hanged and i force shutdown my phone again. After which, I could never turn on my phone again. No splash screen no nothing. I think it is bricked. And yea btw my usb port is not working anymore and it can only be used for charging. And i was running cm11 infected. Can you all please help me thanks!
so no recovery nor download mode?
Sadly, no
TheImpossibleEnemy said:
so no recovery nor download mode?
Click to expand...
Click to collapse
Yep i cannot even boot into anything no splash screen no nothing pressed the power button for like so long i even removed the battery for 2 hours and popped it back in not working
Try this - take out battery,then press and hold volume down+home+power and put battery back without releasing buttons.This may get you into a download mode where you can flash stock jb via odin.
Hello to all,I am in a serious trouble with my samsung galaxy player 5.0 International China version . I rooted this with super one click.And it was successful and there was no problem.But as soon as I overwrote a file in lib folder of system,it got stuck.I tapped the power key and the screens light was gone.I again tapped but there was no response.So I held the power key for a while and the device restarted.But it got stuck on samsung logo and began to restart again and again.So I took it to download mode and tried to nand erase with odin,I thought it could format the device and my device would be fixed.But it took some time and I closed odin.Then I held the power key and it restarted with a black screen containing a picture of malfunctioning connection between a phone and computer at its middle.Then I again tried to t-flash it and again closed it without completion because my notebook had no charge.After that I flashed my device with the YP-G70-Kernel-r14 and it restarted with download mode.But if I hold the power key for a while it restart and again go to the brick showing screen(I heard that this brick is called soft brick).I downloaded two stock rom STOCK_G70XXKPH_G70XXKPH_XEF and G70XXKPL_G70XXKPL_XEF.I tried to flash them in my device with odin and they succeeded.But none of them could fix my problem.They remain in download mode and if I hold the power key the device again go to the soft bricked screen.My device isn't force shutting down.If I hold the power key the screen goes and again lights up with the bricked screen.Now,my device has become very hot and after 8-9 hours it has automatically turned off.But if I connect it to the charger it again lighten up with bricked screen.
Now,I am wanting to setup a clean and clear version of android 2.2/2.3.6 in my device.Is it possible?Will this fix my problem?If it does then please explain me the steps.Or if there is any other way to fix then please help me.
N.B. I am junior about andorid root,rom etc.It is the first device I rooted successfully.
Sorry for my bad and wrong English.
Please,help.I am in a bad danger.
BFahim said:
Hello to all,I am in a serious trouble with my samsung galaxy player 5.0 International China version . I rooted this with super one click.And it was successful and there was no problem.But as soon as I overwrote a file in lib folder of system,it got stuck.I tapped the power key and the screens light was gone.I again tapped but there was no response.So I held the power key for a while and the device restarted.But it got stuck on samsung logo and began to restart again and again.So I took it to download mode and tried to nand erase with odin,I thought it could format the device and my device would be fixed.But it took some time and I closed odin.Then I held the power key and it restarted with a black screen containing a picture of malfunctioning connection between a phone and computer at its middle.Then I again tried to t-flash it and again closed it without completion because my notebook had no charge.After that I flashed my device with the YP-G70-Kernel-r14 and it restarted with download mode.But if I hold the power key for a while it restart and again go to the brick showing screen(I heard that this brick is called soft brick).I downloaded two stock rom STOCK_G70XXKPH_G70XXKPH_XEF and G70XXKPL_G70XXKPL_XEF.I tried to flash them in my device with odin and they succeeded.But none of them could fix my problem.They remain in download mode and if I hold the power key the device again go to the soft bricked screen.My device isn't force shutting down.If I hold the power key the screen goes and again lights up with the bricked screen.Now,my device has become very hot and after 8-9 hours it has automatically turned off.But if I connect it to the charger it again lighten up with bricked screen.
Now,I am wanting to setup a clean and clear version of android 2.2/2.3.6 in my device.Is it possible?Will this fix my problem?If it does then please explain me the steps.Or if there is any other way to fix then please help me.
N.B. I am junior about andorid root,rom etc.It is the first device I rooted successfully.
Sorry for my bad and wrong English.
Please,help.I am in a bad danger.
Click to expand...
Click to collapse
remove your battery and wait 20 seconds plug in your charger without battery wait for 30 seconds then plug out charger then put your battery battery back then charge it try to turn it on
hope it helps
BFahim said:
Hello to all,I am in a serious trouble with my samsung galaxy player 5.0 International China version . I rooted this with super one click.And it was successful and there was no problem.But as soon as I overwrote a file in lib folder of system,it got stuck.I tapped the power key and the screens light was gone.I again tapped but there was no response.So I held the power key for a while and the device restarted.But it got stuck on samsung logo and began to restart again and again.So I took it to download mode and tried to nand erase with odin,I thought it could format the device and my device would be fixed.But it took some time and I closed odin.Then I held the power key and it restarted with a black screen containing a picture of malfunctioning connection between a phone and computer at its middle.Then I again tried to t-flash it and again closed it without completion because my notebook had no charge.After that I flashed my device with the YP-G70-Kernel-r14 and it restarted with download mode.But if I hold the power key for a while it restart and again go to the brick showing screen(I heard that this brick is called soft brick).I downloaded two stock rom STOCK_G70XXKPH_G70XXKPH_XEF and G70XXKPL_G70XXKPL_XEF.I tried to flash them in my device with odin and they succeeded.But none of them could fix my problem.They remain in download mode and if I hold the power key the device again go to the soft bricked screen.My device isn't force shutting down.If I hold the power key the screen goes and again lights up with the bricked screen.Now,my device has become very hot and after 8-9 hours it has automatically turned off.But if I connect it to the charger it again lighten up with bricked screen.
Now,I am wanting to setup a clean and clear version of android 2.2/2.3.6 in my device.Is it possible?Will this fix my problem?If it does then please explain me the steps.Or if there is any other way to fix then please help me.
N.B. I am junior about andorid root,rom etc.It is the first device I rooted successfully.
Sorry for my bad and wrong English.
Please,help.I am in a bad danger.
Click to expand...
Click to collapse
I don't have a samsung device myself but if you can get in download mode and you can from what you described. What happened is that you deleted a driver (from the lib folder) that was necessary for boot (something important). To get to stock go here http://forum.xda-developers.com/showthread.php?t=2192488 download the right Firmware for your device. And the right pit file (pit file is the partition layout of the device). Flash using the pit file you got. You will fix that. Good luck.
Stock rom and pit file downloaded
cedie said:
remove your battery and wait 20 seconds plug in your charger without battery wait for 30 seconds then plug out charger then put your battery battery back then charge it try to turn it on
hope it helps
Click to expand...
Click to collapse
So,I am in the download mode.I downloaded the firmware (XXXKPL) and the intl pit file.Now what options would be checked in odin and where will I put the firmware file(PDA or Bootloader)?The device has no charge.If I connect to the charger,it wakes up and becomes very hot than normal.And I can't turn it off.Its battery is non-removable.Thank you for your valuable help.
Hello guys,
I've got a big problem with my I9300 and therefore I would like to ask here for any help. (If I'm in the wrong section, please move the thread to a correct one)
I had installed the Resurrection Remix ROM, v5.2.6. from 30.12.2014 and Googy-Max 2 recovery (CWM based) on my phone. I was using it for days and all worked fine.
One day I turned the phone off and I wanted to restart it. But it never restarted again; it ends up in a boot loop. It shows me the white Samsung Boot-Logo for some seconds, then a total black screen and the same thing repeats in a loop.
So I wanted to get into the recovery for wiping etc. but I couldn’t access the recovery. Nothing happens by pressing the relevant buttons. The device is still hanging in the boot loop. So I wanted to flash via Odin, but this isn't possible. I also can't go into the download mode. After pressing the relevant buttons, the green warning screen appears, which asks me if I really want to go to the download mode. But when I press volume up for "continue" or even if I don't press anything, the phone turns off and the boot loop with the white Samsung Logo starts again.
Therefore I ordered a USB JIG for forcing the device to go into download mode. When I plug the USB JIG in, the device actually goes into download mode but this status holds on only for a few seconds. After accessing download mode through the JIG, after a few seconds the phone turns off, restarts, (and because the JIG is still plugged in) the download mode appears again and it ends in a loop.
At first I thought maybe the power button is sticking and therefore the device turns on and off autonomous. But definitively I can negate it, because I opened the phone and removed the power button and nothing changed. Also by pressing the power button on the mainboard I can clearly hear the "click".
So I started a new attempt. Although the time, in which the device stays in download mode before turning off, is very short (only a few seconds), I tried flashing an other recovery, namely TWRP v2.8.3.0. So I prepared ODIN, plugged the JIG into the device, by appearing the download mode I switched cables and an other person clicked start at ODIN and it worked. So now TWRP is installed. Now I also can't get into recovery but after flashing TWRP there exist two little differences. First, after pressing the relevant buttons, TWRP appears for less than 1 second until the phone turns off. Secondly, when I plug the device in for charging, the Samsung charging logo appears for some seconds, then for less than 1 second appears a charging logo from Lollipop and the device ends up in a loop by displaying alternately the two different charging logos. Before flashing TWRP, the device booted in a boot loop (as I wrote above) by plugging it in for charging.
So the main question: how can I get my device work again
I tried telling you all details so that you have a better view of the problem.
Maybe I should flash a fully (stock) rom, but as I told you the download mode appears only for a few seconds. Flashing a recovery was possible, because the recovery file is very small - 7 MB. A full rom is much bigger and I think by flashing a complete rom, the device would turn off while Odin is flashing, therefore I ask first here for any assistance.
Thank you very much in advance!
beginnerteur said:
Hello guys,
I've got a big problem with my I9300 and therefore I would like to ask here for any help. (If I'm in the wrong section, please move the thread to a correct one)
I had installed the Resurrection Remix ROM, v5.2.6. from 30.12.2014 and Googy-Max 2 recovery (CWM based) on my phone. I was using it for days and all worked fine.
One day I turned the phone off and I wanted to restart it. But it never restarted again; it ends up in a boot loop. It shows me the white Samsung Boot-Logo for some seconds, then a total black screen and the same thing repeats in a loop.
So I wanted to get into the recovery for wiping etc. but I couldn’t access the recovery. Nothing happens by pressing the relevant buttons. The device is still hanging in the boot loop. So I wanted to flash via Odin, but this isn't possible. I also can't go into the download mode. After pressing the relevant buttons, the green warning screen appears, which asks me if I really want to go to the download mode. But when I press volume up for "continue" or even if I don't press anything, the phone turns off and the boot loop with the white Samsung Logo starts again.
Therefore I ordered a USB JIG for forcing the device to go into download mode. When I plug the USB JIG in, the device actually goes into download mode but this status holds on only for a few seconds. After accessing download mode through the JIG, after a few seconds the phone turns off, restarts, (and because the JIG is still plugged in) the download mode appears again and it ends in a loop.
At first I thought maybe the power button is sticking and therefore the device turns on and off autonomous. But definitively I can negate it, because I opened the phone and removed the power button and nothing changed. Also by pressing the power button on the mainboard I can clearly hear the "click".
So I started a new attempt. Although the time, in which the device stays in download mode before turning off, is very short (only a few seconds), I tried flashing an other recovery, namely TWRP v2.8.3.0. So I prepared ODIN, plugged the JIG into the device, by appearing the download mode I switched cables and an other person clicked start at ODIN and it worked. So now TWRP is installed. Now I also can't get into recovery but after flashing TWRP there exist two little differences. First, after pressing the relevant buttons, TWRP appears for less than 1 second until the phone turns off. Secondly, when I plug the device in for charging, the Samsung charging logo appears for some seconds, then for less than 1 second appears a charging logo from Lollipop and the device ends up in a loop by displaying alternately the two different charging logos. Before flashing TWRP, the device booted in a boot loop (as I wrote above) by plugging it in for charging.
So the main question: how can I get my device work again
I tried telling you all details so that you have a better view of the problem.
Maybe I should flash a fully (stock) rom, but as I told you the download mode appears only for a few seconds. Flashing a recovery was possible, because the recovery file is very small - 7 MB. A full rom is much bigger and I think by flashing a complete rom, the device would turn off while Odin is flashing, therefore I ask first here for any assistance.
Thank you very much in advance!
Click to expand...
Click to collapse
Check and make sure that your volume buttons and home button are not stuck also. If they are not, I would suggest a visit to a repair shop as your EMMC chip might be weak already.
beginnerteur said:
Hello guys,
I've got a big problem with my I9300 and therefore I would like to ask here for any help. (If I'm in the wrong section, please move the thread to a correct one)
I had installed the Resurrection Remix ROM, v5.2.6. from 30.12.2014 and Googy-Max 2 recovery (CWM based) on my phone. I was using it for days and all worked fine.
One day I turned the phone off and I wanted to restart it. But it never restarted again; it ends up in a boot loop. It shows me the white Samsung Boot-Logo for some seconds, then a total black screen and the same thing repeats in a loop.
So I wanted to get into the recovery for wiping etc. but I couldn’t access the recovery. Nothing happens by pressing the relevant buttons. The device is still hanging in the boot loop. So I wanted to flash via Odin, but this isn't possible. I also can't go into the download mode. After pressing the relevant buttons, the green warning screen appears, which asks me if I really want to go to the download mode. But when I press volume up for "continue" or even if I don't press anything, the phone turns off and the boot loop with the white Samsung Logo starts again.
Therefore I ordered a USB JIG for forcing the device to go into download mode. When I plug the USB JIG in, the device actually goes into download mode but this status holds on only for a few seconds. After accessing download mode through the JIG, after a few seconds the phone turns off, restarts, (and because the JIG is still plugged in) the download mode appears again and it ends in a loop.
At first I thought maybe the power button is sticking and therefore the device turns on and off autonomous. But definitively I can negate it, because I opened the phone and removed the power button and nothing changed. Also by pressing the power button on the mainboard I can clearly hear the "click".
So I started a new attempt. Although the time, in which the device stays in download mode before turning off, is very short (only a few seconds), I tried flashing an other recovery, namely TWRP v2.8.3.0. So I prepared ODIN, plugged the JIG into the device, by appearing the download mode I switched cables and an other person clicked start at ODIN and it worked. So now TWRP is installed. Now I also can't get into recovery but after flashing TWRP there exist two little differences. First, after pressing the relevant buttons, TWRP appears for less than 1 second until the phone turns off. Secondly, when I plug the device in for charging, the Samsung charging logo appears for some seconds, then for less than 1 second appears a charging logo from Lollipop and the device ends up in a loop by displaying alternately the two different charging logos. Before flashing TWRP, the device booted in a boot loop (as I wrote above) by plugging it in for charging.
So the main question: how can I get my device work again
I tried telling you all details so that you have a better view of the problem.
Maybe I should flash a fully (stock) rom, but as I told you the download mode appears only for a few seconds. Flashing a recovery was possible, because the recovery file is very small - 7 MB. A full rom is much bigger and I think by flashing a complete rom, the device would turn off while Odin is flashing, therefore I ask first here for any assistance.
Thank you very much in advance!
Click to expand...
Click to collapse
Your power button is failing, stuck in 'pressed' position. Try pressing repeatedly power button for several seconds, then release it completely. It shall bring it back to life. Visit your local service, or prepare tin, heat gun and soldering pistol. One button cost $0.2, they are selling them on eBay in sets of three (and 10, and 100....).
Happened to me some time ago, and video on youtube helped me to dismantle my phone, pull broken button out of it, and change it for new.
My phone was cycling like yours.
beginnerteur said:
Hello guys,
I've got a big problem with my I9300 and therefore I would like to ask here for any help. (If I'm in the wrong section, please move the thread to a correct one)
I had installed the Resurrection Remix ROM, v5.2.6. from 30.12.2014 and Googy-Max 2 recovery (CWM based) on my phone. I was using it for days and all worked fine.
One day I turned the phone off and I wanted to restart it. But it never restarted again; it ends up in a boot loop. It shows me the white Samsung Boot-Logo for some seconds, then a total black screen and the same thing repeats in a loop.
So I wanted to get into the recovery for wiping etc. but I couldn’t access the recovery. Nothing happens by pressing the relevant buttons. The device is still hanging in the boot loop. So I wanted to flash via Odin, but this isn't possible. I also can't go into the download mode. After pressing the relevant buttons, the green warning screen appears, which asks me if I really want to go to the download mode. But when I press volume up for "continue" or even if I don't press anything, the phone turns off and the boot loop with the white Samsung Logo starts again.
Therefore I ordered a USB JIG for forcing the device to go into download mode. When I plug the USB JIG in, the device actually goes into download mode but this status holds on only for a few seconds. After accessing download mode through the JIG, after a few seconds the phone turns off, restarts, (and because the JIG is still plugged in) the download mode appears again and it ends in a loop.
At first I thought maybe the power button is sticking and therefore the device turns on and off autonomous. But definitively I can negate it, because I opened the phone and removed the power button and nothing changed. Also by pressing the power button on the mainboard I can clearly hear the "click".
So I started a new attempt. Although the time, in which the device stays in download mode before turning off, is very short (only a few seconds), I tried flashing an other recovery, namely TWRP v2.8.3.0. So I prepared ODIN, plugged the JIG into the device, by appearing the download mode I switched cables and an other person clicked start at ODIN and it worked. So now TWRP is installed. Now I also can't get into recovery but after flashing TWRP there exist two little differences. First, after pressing the relevant buttons, TWRP appears for less than 1 second until the phone turns off. Secondly, when I plug the device in for charging, the Samsung charging logo appears for some seconds, then for less than 1 second appears a charging logo from Lollipop and the device ends up in a loop by displaying alternately the two different charging logos. Before flashing TWRP, the device booted in a boot loop (as I wrote above) by plugging it in for charging.
So the main question: how can I get my device work again
I tried telling you all details so that you have a better view of the problem.
Maybe I should flash a fully (stock) rom, but as I told you the download mode appears only for a few seconds. Flashing a recovery was possible, because the recovery file is very small - 7 MB. A full rom is much bigger and I think by flashing a complete rom, the device would turn off while Odin is flashing, therefore I ask first here for any assistance.
Thank you very much in advance!
Click to expand...
Click to collapse
As said your emmc chip maybe failing.
The dead boot thread maybe of interest to you.
Virnik0 said:
Your power button is failing, stuck in 'pressed' position. Try pressing repeatedly power button for several seconds, then release it completely. It shall bring it back to life. Visit your local service, or prepare tin, heat gun and soldering pistol. One button cost $0.2, they are selling them on eBay in sets of three (and 10, and 100....).
Happened to me some time ago, and video on youtube helped me to dismantle my phone, pull broken button out of it, and change it for new.
My phone was cycling like yours.
Click to expand...
Click to collapse
He said he has tested this and can also hear the micro-switch clicking.
scorpionhd2 said:
Check and make sure that your volume buttons and home button are not stuck also. If they are not, I would suggest a visit to a repair shop as your EMMC chip might be weak already.
Click to expand...
Click to collapse
Virnik0 said:
Your power button is failing, stuck in 'pressed' position. Try pressing repeatedly power button for several seconds, then release it completely. It shall bring it back to life. Visit your local service, or prepare tin, heat gun and soldering pistol. One button cost $0.2, they are selling them on eBay in sets of three (and 10, and 100....).
Happened to me some time ago, and video on youtube helped me to dismantle my phone, pull broken button out of it, and change it for new.
My phone was cycling like yours.
Click to expand...
Click to collapse
Darke5tShad0w said:
As said your emmc chip maybe failing.
The dead boot thread maybe of interest to you.
He said he has tested this and can also hear the micro-switch clicking.
Click to expand...
Click to collapse
Thank you very much for helping! :good:
So the question is, whether it's the power button's or emmc's fault...
I did a little searching and found this video. I've got exactly the same problem like the guy. At 1:06 following the boot loop, at 1:34 following the problem with downlod mode.
Although he thinks it's caused to the sudden death problem, but at least in my case I think it's wrong because months ago I did the eMMC Brickbug Check.
Also I noticed a probably important detail. When I put the battery in the phone, it automatically turns on without pressing the power button like in 1:04-1:09 in the video. Which normal working phone turns itself on by simply putting in the battery...?
So it must get a command for turning on - (possibly through a defect power button?)
@Virnik0, do you remember, if you could hear the micro-switch clicking on your phone before replacing the button on the mainboard?
beginnerteur said:
Also I noticed a probably important detail. When I put the battery in the phone, it automatically turns on without pressing the power button
Click to expand...
Click to collapse
Your power button is faulty, replace it before you try fixing anything else.
Thank you very, very much for helping! :good: :good: :good:
Truly the power button was fault although you could hear clearly the "click".
I unsoldered and removed the power module and (by startig with JIG and rebooting via ADB) the phone works as it should. :victory:
Now I'm trying to solder a new power button......it's a bit tricky
Again, thank you very much guys!
I had the same problem, pressed the button many times, and it helped. Thank you for your suggestions