I have Motorola Droid Razr XT910 and by RSD I did an update from ICS 4.0.4. to JB 4.1.2. and I decided I want to go back to GB 2.3.5. or 2.3.6. because of the battery life, what is now on JB really short, but I failed of course, so I'm stuck in AP Fastboot mode every time I want to turn my phone on, It will show me this:
Code:
AP Fastboot Flash Mode (S) (Recipe Failure)
0A.77
eMMC Info: Size 16G
To return to normal mode - first press power key to power down
Device is LOCKED. Status Code: 0
And phone is stuck in it, so I need to turn it off, and then power button + vol up + vol down and go through the normal powerup. I have tried another JellyBeans but the problem is in bootloader. I saw here on xda one post telling me I have to flash the radio - I did that about 100 times and I failed... I flashed radio (empty radio) and then in recovery did a wipe data and cache - when i go to recovery after flashing radio, phone will start loading something, maybe the radio, BUT! When it's done, phone will again show me recipe failure...I think I need to unlock bootloader to do a full wipe data and everything, and again start from over. I saw about milion posts here about this problem but with no result... Someone please help me
Related
hello, i brick my phone when i install the new ota ics latam..
what i can do?
thanks
this ota leak.. http://forum.xda-developers.com/showthread.php?t=1688241
What happens when you PWR + Volume Up + Volume Down?
If you could explain a little bit more on what you were doing by the time it bricked, it could help someone figure it out...
Now, what happens when you power it up, holding volumes up and down? Does the boot menu comes up?
Cheers
I have the same problem.
I tryed to flash an Latam ICS after install an 2.3.6. My phone started enter in fc or spend a lot of time on moto logo. Now. It just stay on boot logo. RDS jus flash until step 5 (it recognize my phone, but didnt finish to flash). I can enter in fastboot mode, but this message appear:
ap fast boot flash mode (s)
0a.6c
to return to normal mode - first press power key to power dowm
device is locked. status code 0:
batter ok
ok to program
transfer mode
usb conected.
Somebody can help me please.
Tks
Search on "unblick 4.0.4 tutorial motorola razr" in google.
I hope this help you. good luck!
Hi guys
My XT910 was submerged in a river a couple of weeks ago. It did not short circuit, but I think it got soft bricked.
Whenever it boots, it will display AP Fastboot Flash Mode (S).
I can boot to Boot Mode Selection Menu with Power + Vol+ + Vol-, but I cannot scroll or select anything. I usually enter the page so that I can access BMM to Power Off the device or access the internal storage.
I tried to Fastboot an Asia ROM but the process got stuck at Step 2. I had no choice but to unplug USB. From then on, my laptop could never detect my phone again. I am using the latest Motorola Drivers and cable.
Today, I tried what was suggested here:
http://forum.xda-developers.com/showthread.php?t=1738769
but because my phone could not be detected by my laptop, I transferred the Boot_new.img to MicroSD and used BMM to flash new kernel. (I wasn’t sure what I was doing.)
Now, when I boot my phone, AP Fastboot Flash Mode (S), and what I get after Boot Mode Selection Menu is a brief Motorola logo and Invalid Flash Mode (S) (Boot Failure).
As of last check (half hour ago), battery health was at 96%. I cannot power down the device without BMM, or at least I don’t know how to. Can anyone assist me on restoring my phone to a functional state again?
Edit: prior to all this, my phone was on Euro OTA Jelly Bean
Tom9 said:
Hi guys
My XT910 was submerged in a river a couple of weeks ago. It did not short circuit, but I think it got soft bricked.
Whenever it boots, it will display AP Fastboot Flash Mode (S).
I can boot to Boot Mode Selection Menu with Power + Vol+ + Vol-, but I cannot scroll or select anything. I usually enter the page so that I can access BMM to Power Off the device or access the internal storage.
I tried to Fastboot an Asia ROM but the process got stuck at Step 2. I had no choice but to unplug USB. From then on, my laptop could never detect my phone again. I am using the latest Motorola Drivers and cable.
Today, I tried what was suggested here:
http://forum.xda-developers.com/showthread.php?t=1738769
but because my phone could not be detected by my laptop, I transferred the Boot_new.img to MicroSD and used BMM to flash new kernel. (I wasn’t sure what I was doing.)
Now, when I boot my phone, AP Fastboot Flash Mode (S), and what I get after Boot Mode Selection Menu is a brief Motorola logo and Invalid Flash Mode (S) (Boot Failure).
As of last check (half hour ago), battery health was at 96%. I cannot power down the device without BMM, or at least I don’t know how to. Can anyone assist me on restoring my phone to a functional state again?
Edit: prior to all this, my phone was on Euro OTA Jelly Bean
Click to expand...
Click to collapse
Theres no way back to ICS after updating to euro jelly bean, read the first post carefully, it warned you about it
You can use this tutorial how to unbrick it
http://forum.xda-developers.com/showthread.php?t=2194825
Sent from my GT-I9300 using xda app-developers app
Hi Guys,
I really need your help.
After tried upgarde to LIQUIDSMOOTH JB, i found that my baseband doesn't work in my country (i'm in Indonesia).
I tried to updated my baseband with BMM but not work.
So i decide to do fastboot from ICS then upgrade to Liquidsmooth in proper way.
What I did:
- backup CID
- erase CID
- get ICS fastboot file asia retail
- ap fastboot with rsd
- after reboot manual and go to BP Tool
- my phone entering the system but then it back to screen moto again
- since i used verizon phone, i tried to fasboot with EU fastboot ICS file
- ap fastboot with rsd
- manual reboot and go to bp tool
- screen shows, updating system, starting system but then it throw me back to screen moto again
now my battery is low, and i'm waiting for desktop charger
what i need to do to get my phone back?
after rsd done flash my phone, i got message in status "Please manually power up this phone"
what i did then:
- unplug phone from usb cable,
- reboot phone (volume up + down, power, after led flashing, i release all buttons)
- then i press again volume up + down, power , after led flashing, i keep pushing volume up + down untill ap fastboot menus appears
- i plug again usb and waiting until result in rsd shows PASS
Am i did the right steps?
Thank you in advance for your suggestions
same problem with me
idwijayaku said:
Hi Guys,
I really need your help.
After tried upgarde to LIQUIDSMOOTH JB, i found that my baseband doesn't work in my country (i'm in Indonesia).
I tried to updated my baseband with BMM but not work.
So i decide to do fastboot from ICS then upgrade to Liquidsmooth in proper way.
What I did:
- backup CID
- erase CID
- get ICS fastboot file asia retail
- ap fastboot with rsd
- after reboot manual and go to BP Tool
- my phone entering the system but then it back to screen moto again
- since i used verizon phone, i tried to fasboot with EU fastboot ICS file
- ap fastboot with rsd
- manual reboot and go to bp tool
- screen shows, updating system, starting system but then it throw me back to screen moto again
now my battery is low, and i'm waiting for desktop charger
what i need to do to get my phone back?
after rsd done flash my phone, i got message in status "Please manually power up this phone"
what i did then:
- unplug phone from usb cable,
- reboot phone (volume up + down, power, after led flashing, i release all buttons)
- then i press again volume up + down, power , after led flashing, i keep pushing volume up + down untill ap fastboot menus appears
- i plug again usb and waiting until result in rsd shows PASS
Am i did the right steps?
Thank you in advance for your suggestions
Click to expand...
Click to collapse
same problem with me :crying:
have you find the solution ?
(uda ktmu solusinya bos ? klo uda mohon share ya...)
What is your battery status????
Sent from my LT28h using xda premium
alwaysdksh said:
What is your battery status????
Sent from my LT28h using xda premium
Click to expand...
Click to collapse
During flashing i charge until more than 90%
Now I can only go to BP HW Diag, but cannot go to system with BP Tools
What should I do?
alihabibie said:
same problem with me :crying:
have you find the solution ?
(uda ktmu solusinya bos ? klo uda mohon share ya...)
Click to expand...
Click to collapse
(hehehe pasti dikabarin kalo udah solve bos)
I have Motorola Droid Razr XT910 and by RSD I did an update from ICS 4.0.4. to JB 4.1.2. and I decided I want to go back to GB 2.3.5. or 2.3.6. because of the battery life, what is now on JB really short, but I failed of course, so I'm stuck in AP Fastboot mode every time I want to turn my phone on, It will show me this:
Code:
AP Fastboot Flash Mode (S) (Recipe Failure)
0A.77
eMMC Info: Size 16G
To return to normal mode - first press power key to power down
Device is LOCKED. Status Code: 0
And phone is stuck in it, so I need to turn it off, and then power button + vol up + vol down and go through the normal powerup. I have tried another JellyBeans but the problem is in bootloader. I saw here on xda one post telling me I have to flash the radio - I did that about 100 times and I failed... I flashed radio (empty radio) and then in recovery did a wipe data and cache - when i go to recovery after flashing radio, phone will start loading something, maybe the radio, BUT! When it's done, phone will again show me recipe failure...I think I need to unlock bootloader to do a full wipe data and everything, and again start from over. I saw about milion posts here about this problem but with no result... Someone please help me
fufixiil said:
I have Motorola Droid Razr XT910 and by RSD I did an update from ICS 4.0.4. to JB 4.1.2. and I decided I want to go back to GB 2.3.5. or 2.3.6. because of the battery life, what is now on JB really short, but I failed of course, so I'm stuck in AP Fastboot mode every time I want to turn my phone on, It will show me this:
Code:
AP Fastboot Flash Mode (S) (Recipe Failure)
0A.77
eMMC Info: Size 16G
To return to normal mode - first press power key to power down
Device is LOCKED. Status Code: 0
And phone is stuck in it, so I need to turn it off, and then power button + vol up + vol down and go through the normal powerup. I have tried another JellyBeans but the problem is in bootloader. I saw here on xda one post telling me I have to flash the radio - I did that about 100 times and I failed... I flashed radio (empty radio) and then in recovery did a wipe data and cache - when i go to recovery after flashing radio, phone will start loading something, maybe the radio, BUT! When it's done, phone will again show me recipe failure...I think I need to unlock bootloader to do a full wipe data and everything, and again start from over. I saw about milion posts here about this problem but with no result... Someone please help me
Click to expand...
Click to collapse
You can't unlock bootloader,unfortunately no one can.
Did you try to flash JB with RSD Lite again?
Sent from my Razr XT910
welder73 said:
You can't unlock bootloader,unfortunately no one can.
Did you try to flash JB with RSD Lite again?
Sent from my Razr XT910
Click to expand...
Click to collapse
Yes, I did. I tried to first delete cache and everything and then flash new JB, or just flash it, or flash and then delete cache and data.
fufixiil said:
Yes, I did. I tried to first delete cache and everything and then flash new JB, or just flash it, or flash and then delete cache and data.
Click to expand...
Click to collapse
What do you mean "delete cache"?
Here http://forum.xda-developers.com/showthread.php?t=2231289 are the JB Fastboot files
Here https://dl.dropboxusercontent.com/u/42057363/RSDLite_v6.1.x.zip is RSD Lite 6.1.5
Here https://motorola-global-portal.custhelp.com/app/answers/detail/a_id/88481/action/auth are the Motorola drivers
Install drivers,install RSD Lite
Start RSD Lite,click on 3 dots next to empty bar,find JB Fastboot file that you downloaded,click open and then "decompress only"
When program finish that,shut the phone off,press vol- vol+ and power button,choose AP Fastboot,connect the phone with usb cable to the computer,wait a program to recognize the phone and then press start in RSD Lite.
welder73 said:
What do you mean "delete cache"?
Here http://forum.xda-developers.com/showthread.php?t=2231289 are the JB Fastboot files
Here https://dl.dropboxusercontent.com/u/42057363/RSDLite_v6.1.x.zip is RSD Lite 6.1.5
Here https://motorola-global-portal.custhelp.com/app/answers/detail/a_id/88481/action/auth are the Motorola drivers
Install drivers,install RSD Lite
Start RSD Lite,click on 3 dots next to empty bar,find JB Fastboot file that you downloaded,click open and then "decompress only"
When program finish that,shut the phone off,press vol- vol+ and power button,choose AP Fastboot,connect the phone with usb cable to the computer,wait a program to recognize the phone and then press start in RSD Lite.
Click to expand...
Click to collapse
I also have the recipe failure and have tried all of these steps (and many others) to try and fix the "recipe failure" at boot.
welder73 said:
What do you mean "delete cache"?
Here http://forum.xda-developers.com/showthread.php?t=2231289 are the JB Fastboot files
Here https://dl.dropboxusercontent.com/u/42057363/RSDLite_v6.1.x.zip is RSD Lite 6.1.5
Here https://motorola-global-portal.custhelp.com/app/answers/detail/a_id/88481/action/auth are the Motorola drivers
Install drivers,install RSD Lite
Start RSD Lite,click on 3 dots next to empty bar,find JB Fastboot file that you downloaded,click open and then "decompress only"
When program finish that,shut the phone off,press vol- vol+ and power button,choose AP Fastboot,connect the phone with usb cable to the computer,wait a program to recognize the phone and then press start in RSD Lite.
Click to expand...
Click to collapse
I mean wipe everything in recovery (cache and data). And I did now step by step and still getting recipe failure.
i went through a lot of threads simillar to this problem but cannot find/understand what to do...
Because flash wrong firmware, so my razr v xt910 appears this notification when boot :
AP Fastboot Flash Mode (S) (Flash Failure)
0A.77
To return to normal mode - first press power key to power down
Device is LOCKED. Status Code : 0
Battery OK
OK to Program
Connect USB
Data Cable
I can only boot normally by press Vol Up + Vol Down + Power, then select Normal Powerup to boot.
Therefore, does anyone know this situation to fix it ?
i got Jelly Bean 982.124.14.XT910.Retail.en.AU (phone came with it) but i cant even find same firmware to flash.
(i tried this solutions: [ FLASH ] Motorola Razr Flash Failure [ Solution ], tried i think every firmware from sbf.droid-developers.org -Motorola Firmwares every time when i try to flash in gives me an error)
EDIT:
stared to downloading again every 4.1.2 firmwares and flashing and found one that worked for me
Blur_Version.982.124.18.XT910.Fido.en.CA
PLEASE, MODERATOR CLOSE THE THREAD
Thanks for posting this - was my problem too! Bricked with Bootloader 0A.77, no BMM/SS to help out and RSD Lite giving me "Signed Error" for builds that were supposed to work...
Flashed the Blur_Version.982.124.18.XT910.Fido.en.CA (from http://motofirmware.center/files/file/244-982o-124-spul-18-fido-p006-a007-s1ff-cfcxmlzip ) and that worked perfectly, and got my XT910 working again - yay! Now I can add tools and SS and sort it out properly.