So, this is kind of an odd problem, but I'm not even sure where to begin with it.
So I've currently own two phone cases: The CP12 straight from Sony, and the Brando Case from what I can only assume is the deepest parts of cheap things China.
Anywho, last night my CP12 stopped charging my phone. Just flat out acts like it's not connected on both fronts (My phone doesn't acknowledge being plugged in and my case doesn't think a phone is plugged in. Annoyed, but whatever.
This morning my Brando case arrived and I tried it out, and, same thing. Neither the case nor the phone acknowledge that they're connected to each other.
Now, normally, this leads one to believe that the magnetic port is busted, right? But here's the weird thing: The magnetic cord I got with the CP12 DOES work when I plug it straight into the phone- It works completely fine, as a matter of fact.
Just curious if anyone else has seen this problem and has a solution. I hadn't changed anything on the software front between working and not- I just noticed at one point that the case wouldnt' charge the phone.\
EDIT: My phone exists in a quantum state of just wanting to annoy me.
Shadow of Chaos said:
So, this is kind of an odd problem, but I'm not even sure where to begin with it.
So I've currently own two phone cases: The CP12 straight from Sony, and the Brando Case from what I can only assume is the deepest parts of cheap things China.
Anywho, last night my CP12 stopped charging my phone. Just flat out acts like it's not connected on both fronts (My phone doesn't acknowledge being plugged in and my case doesn't think a phone is plugged in. Annoyed, but whatever.
This morning my Brando case arrived and I tried it out, and, same thing. Neither the case nor the phone acknowledge that they're connected to each other.
Now, normally, this leads one to believe that the magnetic port is busted, right? But here's the weird thing: The magnetic cord I got with the CP12 DOES work when I plug it straight into the phone- It works completely fine, as a matter of fact.
Just curious if anyone else has seen this problem and has a solution. I hadn't changed anything on the software front between working and not- I just noticed at one point that the case wouldnt' charge the phone.
Click to expand...
Click to collapse
check the output on your case. If its under 500mAh then it wont charge through the magnetic dock. You've probably noticed the USB wont charge through the magnetic dock either. So possibly the output has been disrupted in the case and is under 500.. ?? Thats all i can think of.
hamdogg said:
check the output on your case. If its under 500mAh then it wont charge through the magnetic dock. You've probably noticed the USB wont charge through the magnetic dock either. So possibly the output has been disrupted in the case and is under 500.. ?? Thats all i can think of.
Click to expand...
Click to collapse
... You know, I said I wouldn't make a stupid topic about this, so I'd check a couple of times. And it didn't charge then.
And now the CP12 does charge the phone. When nothing has changed. The Brando doesn't, which is a shame, but meh.
Thanks for the help regardless.
EDIT: Oh, to clarify, I don't have a magnetic dock, so that's not a test. Still, things work, so...
Related
Just found this at amazon and it allows you to charge your S2 with a case on it..
http://www.amazon.com/Sinjimoru-Sta...VKH0/ref=sr_1_3?ie=UTF8&qid=1318089770&sr=8-3
Hmm that looks interesting. I wonder how stable it is.
There are some video reviews for it on youtube. It looks pretty stable...
That looks nicer than having tto take my phone out of the case to work with the infuse dock
Sent from my SAMSUNG-SGH-I777 using xda premium
want one.. in yellow or white.. xD
wish it had audio port
falcon26 said:
Just found this at amazon and it allows you to charge your S2 with a case on it..
http://www.amazon.com/Sinjimoru-Sta...VKH0/ref=sr_1_3?ie=UTF8&qid=1318089770&sr=8-3
Click to expand...
Click to collapse
Ya...I bought that dock and it's *crap*. Received it today at work and used it for about 1/3 of the day. My desk is completely flat and with the *slightest* tip (or even the headphone cord moving while plugged in) the entire thing rolls backwards. I had to push it up against one of my monitors to keep it upright. On top of it, the entire thing feels *really* cheap (like it could break at any moment) and the phone isn't even kept stationary on top of it. It relies on the cable connection to keep it upright...which is doesn't. The phone moves around without a problem.
Overall, not worth the money. I'll be sending it back tomorrow.
hotleadsingerguy said:
Ya...I bought that dock and it's *crap*. Received it today at work and used it for about 1/3 of the day. My desk is completely flat and with the *slightest* tip (or even the headphone cord moving while plugged in) the entire thing rolls backwards. I had to push it up against one of my monitors to keep it upright. On top of it, the entire thing feels *really* cheap (like it could break at any moment) and the phone isn't even kept stationary on top of it. It relies on the cable connection to keep it upright...which is doesn't. The phone moves around without a problem.
Overall, not worth the money. I'll be sending it back tomorrow.
Click to expand...
Click to collapse
Yikes! I just ordered one of these.
I'm finding that charging the phone in a case is a real problem unless I use the stock usb cord. I have a zillion other cables that work but not with a case. Not psyched about ordering more stock cables. I bet the official dock doesn't work with a case.
Any other solutions with extended connectors for use in a case??
I just got mine and it is not exactly what I expected but it does get the job done. I do not have any stability issues with it, I can actually tilt it backwards about 25 degrees with my phone on it before it falls backward, I do think it would benefit from some extra mass but with the phone on it I have not problem with it. I have the Ballistic case on mine and my problem was that the cable that came with this dock would not reach far enough into my device to make a connection because my case basically adds some depth to the port. I had two choices, either modify my case or the dock. What I ended up having to do was modify the cable that came with the dock with a longer micro usb port at the end so that it would make contact while on the base. Although I agree that this dock could be better, it does accomplish what I needed it to, just needed some help. I have a dock for every one of my devices, but this is the first one that lets me leave my case on.
BigBopper said:
Yikes! I just ordered one of these.
I'm finding that charging the phone in a case is a real problem unless I use the stock usb cord. I have a zillion other cables that work but not with a case. Not psyched about ordering more stock cables. I bet the official dock doesn't work with a case.
Any other solutions with extended connectors for use in a case??
Click to expand...
Click to collapse
For charging micro USB cables you could try to locate one of the ones for the nook color. Worked fine on my old captivate and works great on my new sgs2 even with the case on.
Sent from my SAMSUNG-SGH-I777 using xda premium
My gs2 fits in my infuse dock with my tpu case on like it was made for it!
sent from my gs2....War Eagle!
would it be possible to use the mhl adapter cable and turn this into a tv dock? i dont know if you could replace the larger usb cable that is included and swap it with the mhl one and have power to it and hdmi conencted at all times.
has anyone tried this who bought this item?
So my tablet stopped charging yesterday. I know a lot of people are having issues with their wall charger, but I think my problem is due to the 40 pin connector. It looks like two or three of the pins got bent (not sure how). Every time I plug it in, it has a light crunching feeling. The wire to tablet connection is not sturdy at all and tends to bend downwards due to a lack of support in the tablet. Asus is sending me info on how to return the device. The tablet has been amazing other than this poor design. Anyone else having this issue?
punkcitykid said:
So my tablet stopped charging yesterday. I know a lot of people are having issues with their wall charger, but I think my problem is due to the 40 pin connector. It looks like two or three of the pins got bent (not sure how). Every time I plug it in, it has a light crunching feeling. The wire to tablet connection is not sturdy at all and tends to bend downwards due to a lack of support in the tablet. Asus is sending me info on how to return the device. The tablet has been amazing other than this poor design. Anyone else having this issue?
Click to expand...
Click to collapse
Mine wouldn't charge/transfer data but that's because the connector fell apart. Not sure how your pins managed to get bent, but it should be easily rectified via RMA. Until you get your new charger you could probably snag an OG TF charger and use that. However, I would also check the socket on the Prime itself, see if there is anything "odd?" going on in there that could have bent the pins (and possibly do it again once you get another charger).
same problem here- I started another thread. the tablet will no longer charge. It was intermittent at first. sometimes it would stop charging without ever removing the charger or 40 pin connector from the device.
I don't know if it is just a bad charger/cable , or if there is something wrong internally on the tablet. I will be shipping mine back for full refund from where i purchased, unless there is something else to try?
Anyone else have this issue. The usb cable comes apart on the asus end(see pic)
P.s. this has never been abused and was treated with the the greatest of care
http://imgur.com/AOPWP
Nope, maybe try a tiny dab of superglue?
Well I know it is an easy fix I just thought it was kinda weird and wanted to know if I was the only one who had this problem
Yup happened to me. But on the other side. The USB side. Cant sseem to attach the pic from my tfp
i had this happen to me right out of the box! plugged the device in to charge then unplug after full charge then this happened.
susko said:
Anyone else have this issue. The usb cable comes apart on the asus end(see pic)
P.s. this has never been abused and was treated with the the greatest of care
http://imgur.com/AOPWP
Click to expand...
Click to collapse
Yes! It's a piece of crap! And I tried to RMA to Asus but they want the bad one back and then they'll send out a new or fixed one. So how is a person supposed to charge the tablet with no power cord? Very disappointing, Asus! They've sent me several follow up surveys to the phone calls and emails and I've told them how I feel about this. They don't seem to respond after that... Haha! Oh, well. The superglue route is probably the best way to go, anyhow.
My cable came apart like that the first time I used it. I carefully removed it from the connector on my tablet so as not to damage any wires, and then pushed the cap back on until it clicked and it hasn't come off since.
I think the problem is that the black cap isn't properly seated over the connector on some charging cables so the little clips on the inside never engaged. I have a half dozen chargers for the TF Prime and 3 were like this.
This is definitely something that might scare you the first time you try to unplug your connector, but it isn't a huge problem unless you rip out the wires or something.
My wife's did this the first time we unplugged it. I used a few drops of super glue on it and it has never come apart again. Mine on the other hand never had the issue. I think there was a batch of the plugs that they never put the glue on them so they weren't sealed when they got shipped. Put a few drops of glue on it and seal it up and enjoy the full use of the USB plug
Sent from my Transformer Prime TF201 using xda premium
I've ordered the Z2 and it should be coming to my door any day now. When I realized that a magnetic charger might be a good idea to prevent wear of the microUSB port I started to look at the options available. Unfortunately the charging dock sold by Sony is too expensive in my opinion and I would like to find an off-brand alternative. I've looked through the posts on this forum and have come to understand that putting the charger in the wrong direction could be a big mistake. I'm still willing to buy just a cable but would prefer a dock to help prevent this.
My questions is does anyone have a suggestion for a dock(preferable) / cable?
I found this cable on amazon:
http://www.amazon.ca/gp/product/B00...pf_rd_t=101&pf_rd_p=1947489602&pf_rd_i=915398
PS: A lot of docks on amazon have some bad reviews and I'm wary of buying them
I was in the same boat. The Sony dock looks nice like but it was fairly expensive.
I just ordered this last week:
http://www.amazon.ca/Magnector-Perf..._1_2?s=wireless&ie=UTF8&qid=1421124799&sr=1-2
I've got genuine Sony and this one as well. Sony charger is cut more precisely, phone is held exactly as it should with no wiggle etc. But this alone doesn't justify 10 times higher price. The cheapo one does the job in the same way, I see no difference in charging speed. For example this cable is OK as well. If you don't mind waiting for delivery (it takes about 4 weeks to Europe), I can only recommend these products and Aliexpress site.
Regarding the cables with LED indicator - I've got one and even if it's interesting I don't find it useful. LED light is always on and when it reaches ~95% battery threshold it starts to flicker until fully charged, then the color changes to solid again.
Is it hard to screw up the direction of the charger? I've heard it will completely discharge the battery (It shorts the terminals?)
Also, is there a thin case that has a slot for the magnetic charging / what cases do you use if any?
Thanks for the info guys!
Theoretically the plastic around the terminals should prevent the connector from actually connecting "the wrong way" but in practice it can still happen, especially if you insist in moving and pushing the cable.
If the cable is coming out from "the middle" of the connector is easier to put it wrong (otherwise is easy to remember the cable has to go from the middle of the phone to the bottom so is much harder to make the mistake). However because the phone is so symetric you might confuse the front with the back and put it in reverse even in the docking station.
And last but not least make sure you have good warranty - it is possible that the magnet will "suck out" the connector from the phone, mine is barely hanging and is supposed to be from the batch that fixed this issue.
I have the original Sony dock as well as a third party dock. I also have a magnetic adapter for micro USB. All are working fine. Here are the links:
Third party dock - this works fine with my Z2 even though the title says Z3.
Micro USB adapter
Thanks for the reply unni_kmr, unfortunately I'm in Canada and I can't order through amazon.com easily. (Also that isn't on amazon.ca)
Anyone have input on whether I should get this dock for $15?
http://www.amazon.ca/PatecĀ®-Magneti...=UTF8&qid=1421438530&sr=1-15&keywords=z2+case
Also, I'm looking for a case that's slim but doesn't impede the magnetic charging port. Any suggestions?
EDIT: Found this case, might try to cut a charging hole myself
http://www.amazon.ca/Xcessor-Vapour...id=1421440356&sr=8-2&keywords=z2+case+xcessor
WGuitar said:
Also, I'm looking for a case that's slim but doesn't impede the magnetic charging port. Any suggestions?
Click to expand...
Click to collapse
I don't have a case. I am using the Mocolo tempered glass on front and back. I bought it from here. Its very thin glass. Even with it on the front and back, the phone slides into the docks easily.
slow charging speed
hi there, i recently updated my Z2 , to 4.4.4 and everything is absolutely as expected but magnetic charging speed has taken a serious blow. with 4.4.2 it was as fast as normal cable charging but now with 4.4.4 it has become extremely slow , almost takes 8 minutes to charge 1%, and more than 8-9 hrs to fully charge ..
anyone else facing a similar issue .....kindly suggest solutions.:crying:
thanks
WGuitar said:
I've ordered the Z2 and it should be coming to my door any day now. When I realized that a magnetic charger might be a good idea to prevent wear of the microUSB port I started to look at the options available. Unfortunately the charging dock sold by Sony is too expensive in my opinion and I would like to find an off-brand alternative. I've looked through the posts on this forum and have come to understand that putting the charger in the wrong direction could be a big mistake. I'm still willing to buy just a cable but would prefer a dock to help prevent this.
My questions is does anyone have a suggestion for a dock(preferable) / cable?
I found this cable on amazon:
http://www.amazon.ca/gp/product/B00...pf_rd_t=101&pf_rd_p=1947489602&pf_rd_i=915398
PS: A lot of docks on amazon have some bad reviews and I'm wary of buying them
Click to expand...
Click to collapse
What do you mean by putting the charger in the wrong direction could be bad. Do you mean the magnetic charger can only work in one specific direction?
y300owner said:
What do you mean by putting the charger in the wrong direction could be bad. Do you mean the magnetic charger can only work in one specific direction?
Click to expand...
Click to collapse
Not only it can work in only one direction but even worse if you manage to make it connect in reverse it might break the phone or the battery. Yay Sony!
d210 said:
Not only it can work in only one direction but even worse if you manage to make it connect in reverse it might break the phone or the battery. Yay Sony!
Click to expand...
Click to collapse
I use a "magnetron" cable for several moths now and never had any issues with it.
It is not possible to connect it in the wrong orientation.
I'm really happy with it and would absolutely buy it again.
kuhno said:
I use a "magnetron" cable for several moths now and never had any issues with it.
It is not possible to connect it in the wrong orientation.
I'm really happy with it and would absolutely buy it again.
Click to expand...
Click to collapse
Very expensive cable though...
And if you wiggle it a bit I'm sure you can make contact with it even in reverse. I assume it is using like any other cable the normal "mechanical protection" which consists in a tiny (fraction of a mm) extra plastic on the "lower" pin from magnetic connector.
I use the DK30 charging dock and occasionally a usb magnetic charging cable. Actually I haven't opened the USB for a couple of months now. However, today I was surprised to see that the magnetic connector from the phone was left in the dock
Has anyone had a similar issue and how you fix it? My ZU is still under warranty, however in another country. I'm considering gluing it back in with something, but I'm unsure whether it would be sufficient for the waterproofing.
I searched around a little, and it looks like you're not the only one facing this issue. The Z2 and the Z3C users have also reported that the magnetic connector falls off. Here's a thread about the Z2's issues. One user managed to fix it himself though by, and I quote:
Here's what I did with mine.
All I did was I got a AAA battery and used the + end of the battery and forced it in real hard. Now it won't come out. Even with the very stong magtron magnet. It must have clipped back into place when I forced it in.
Also my phone is waterproof again as I tested it by dunking it in a bowl of water.
Might not work with everyone but worked for me.
Click to expand...
Click to collapse
You could try that, and if it doesn't work, then you could possibly glue it back on. What country are you currently in, and where did you buy it from?