Hi everyone, hoping for some help.
My galaxy s2 wont power on at all.... I have tried plugging USB into the PC and pressing Vol Up but nothing - this happened after replacing the USB charge port. The power flex cable accidentally ripped off.
I plug it into my laptop and it starts installing the driver but then fails. Anyone experienced this before?
Detach battery, leave it in 5 minute and attach again , power on. I face this problem before(but the cause is not same to you ) and my phone power on after i do those steps. Hope your phone will work again.
Or you could wait for KeithHarris39 who knows what he's talking about with this stuff to read your thread (he's posted to Q&A in the last hour or two, so he's probably around somewhere) & he'll actually give you some idea of what might have gone wrong/what you can do about it.
MistahBungle said:
Or you could wait for KeithHarris39 who knows what he's talking about with this stuff to read your thread (he's posted to Q&A in the last hour or two, so he's probably around somewhere) & he'll actually give you some idea of what might have gone wrong/what you can do about it.
Click to expand...
Click to collapse
i cant send u a pm ...tried it says u dont want to get disturbed..
^^^
Why would you want to send me a PM ? I have the PM system turned off by design.
MistahBungle said:
^^^
Why would you want to send me a PM ? I have the PM system turned off by design.
Click to expand...
Click to collapse
something worth ur interest...
If you are describing the flex cable that is/was attached to the USB charger board.....then the 'inadvertent detachment' is likely the cause of your issues......
First, the damage that *has* taken place is likely to have caused a lack of charge reaching the battery....which is likely the reason the phone won't boot....dead battery and no way to charge it.
Second, it's likely the PC isn't installing the drivers as the damage caused is probably stopping the PC recognising the phone for what it is.....we all know PC's are dumb, if they're not told exactly how to do something, they just sit there scratching their metaphorical heads....lol
Repairing this part is *highly unlikely* to succeed........the only option....get another replacement.... the only saving grace......they're not that expensive......
Sent from my GT-I9100 using Tapatalk
I very much doubt you have anything to say to me in PM that would be 'worth my interest'. However, if you still believe that to be the case, this thread is as good a place as any to say it.
doctor_droid said:
something worth ur interest...
Click to expand...
Click to collapse
Maybe its the winner of the next Melbourne Cup..........
MistahBungle said:
I very much doubt you have anything to say to me in PM that would be 'worth my interest'. However, if you still believe that to be the case, this thread is as good a place as any to say it.
Click to expand...
Click to collapse
just wanted to ask u whether u would be interested for getting a RC title..if yes then would have nominated u to the committee .
u really thought i would ask u for investing money
Thankyou for the offer, that's very kind of you to think of me that way & I do appreciate it But no, I'd rather not, thanks.
Why not ? You might be a gambling guru for all we know
doctor_droid said:
just wanted to ask u whether u would be interested for getting a RC title..if yes then would have nominated u to the committee .
u really thought i would ask u for investing money
Click to expand...
Click to collapse
MistahBungle said:
Thankyou for the offer, that's very kind of you to think of me that way & I do appreciate it But no, I'd rather not, thanks.
Why not ? You might be a gambling guru for all we know
Click to expand...
Click to collapse
k mate ..its ur decision c ya around here itself till my s2 lives...
keithross39 said:
If you are describing the flex cable that is/was attached to the USB charger board.....then the 'inadvertent detachment' is likely the cause of your issues......
First, the damage that *has* taken place is likely to have caused a lack of charge reaching the battery....which is likely the reason the phone won't boot....dead battery and no way to charge it.
Second, it's likely the PC isn't installing the drivers as the damage caused is probably stopping the PC recognising the phone for what it is.....we all know PC's are dumb, if they're not told exactly how to do something, they just sit there scratching their metaphorical heads....lol
Repairing this part is *highly unlikely* to succeed........the only option....get another replacement.... the only saving grace......they're not that expensive......
Sent from my GT-I9100 using Tapatalk
Click to expand...
Click to collapse
Thought as much but only just got back on here. Thanks for your time. Already ordered the bits that all arrived today ( except I missed the bloody posty )
So I will let you know how my soldering skills hold up after years of being dormant! The board itself seems fine... just kicking myself for giving it that little pull and forgetting that the power button is stuck on. Doh!! The phone is my old one and now belongs to the Mrs... wasn't too happy with me lol. So much so, and I'm sorry to say she switched to the dark side.. iPhone.
Now I think I'll see what ROMs are good for the s4... easy rooted it from day one but now I feel ready for a change. First android I've never completely changed
Sent from my GT-I9505 using XDA Premium 4 mobile app
Ok so I reattached the parts.. but still won't boot up. I plug it into the laptop and connect to Odin.. the id:com turns blue and unknown upload mode is on screen... but it just hangs and does nothing any ideas?
Sent from my GT-I9505 using XDA Premium 4 mobile app
Related
hello,
Has anyone looked into finding the debug/jtag pins/port?
I have a 100% bricked vibrant here. Someone gave me. I want to start to look into it. Looking for some help.
New pics up using a tri-pod.
Small pics
http://www.mrcellphoneunlocker.com/vibrant_macro
Raw Large Pics
http://www.mrcellphoneunlocker.com/vibrant_macro/Raw/
Doing some searching around I found the CPU is a S5PC110 and i found a dev-board.
http://www.armdesigner.com/KIT S5PC110 (Android 2.1).html
[email protected]
Thanks!
What are those?
It's what you use to fix/base flash bricked phones.
How the hell did you get a 100% bricked vibrant I didnt think they existed.
Sgs
Doubt it is bricked. Maybe hardware dead, but not bricked.
Unless he tested something for you that you were not willing to test.
Sent from my SGH-T959 using XDA App
Vanilla gorilla said:
How the hell did you get a 100% bricked vibrant I didnt think they existed.
Sgs
Click to expand...
Click to collapse
I had one as well, but it was my fault, I clicked "repartition" on Odin. I couldn't find a fix so I exchanged it within the 14 days.
They exist... I had one... Wouldn't power on at all..
No recovery
No download
No vibrant screen
Sent from my SGH-T959 using XDA App
kopykatkiller said:
Doubt it is bricked. Maybe hardware dead, but not bricked.
Unless he tested something for you that you were not willing to test.
Sent from my SGH-T959 using XDA App
Click to expand...
Click to collapse
My apps dont brick phones.
He flashed MS_GURU rom -> and tried to go back to US. and it died. no power to screen. the phone just gets hot. Ive disas the phone. I will take some pics soon.
But, nice try on the bash.
As Fes would say... "ah, burn..."
Hahaha
But yeah your app doesn't work..
Sent from my SGH-T959 using XDA App
rhcp0112345 said:
He flashed MS_GURU rom -> and tried to go back to US. and it died. no power to screen. the phone just gets hot. Ive disas the phone. I will take some pics soon.
Click to expand...
Click to collapse
Nice. Please do. Then we can finally settle what chip is running and if there is FM hardware or not. Hope you have a nice camera! I want HUGE and close pics
BTW, what you think the odds are the usb doubles as jtag? Briefly going through all the code, I could have sworn I saw stuff related to ttyS0, baud rates and all. Maybe just need the right pinout.
fearmonkey said:
Nice. Please do. Then we can finally settle what chip is running and if there is FM hardware or not. Hope you have a nice camera! I want HUGE and close pics
BTW, what you think the odds are the usb doubles as jtag? Briefly going through all the code, I could have sworn I saw stuff related to ttyS0, baud rates and all. Maybe just need the right pinout.
Click to expand...
Click to collapse
Would be interesting. Im going to take the pics as soon as i can. its weekend. prob monday or tuesday.
if you think it works as TTY. Its possible. I dont see any pins on the boards. Thats why i asked.
JTAG and serial console are different things. jtag won't show in the kernel, it is a physical set of pins for direct access to the cpu and/or flash.
The serial console might be available via usb (eg on the g1 it is, with a custom cable) but it is only helpful for kernel debugging - if a kernel is broken, but not too broken, you can get logs out of it while it starts up..
Ok. I made an attempt at taking the pics. This is my first time to do macro shots
If anyone can give me suggestions to make better. Let me know.
http://www.mrcellphoneunlocker.com/vibrant_macro/MrCellPhoneUnlocker/TMO_Samsung_Photos.html#grid
Disconn3ct said:
JTAG and serial console are different things. jtag won't show in the kernel, it is a physical set of pins for direct access to the cpu and/or flash.
The serial console might be available via usb (eg on the g1 it is, with a custom cable) but it is only helpful for kernel debugging - if a kernel is broken, but not too broken, you can get logs out of it while it starts up..
Click to expand...
Click to collapse
Indeed. But seeing the tty stuff in the kernel just made me think that if the usb can double as a serial port, it might also double (triple?) as an easy to reach jtag port. Then again, I dunno how many cables a jtag needs. iirc, microusb has 5.
New pics up using a tri-pod.
http://www.mrcellphoneunlocker.com/vibrant_macro
let me know
Raw pics big ones: Best quality: http://www.mrcellphoneunlocker.com/vibrant_macro/Raw/
MOD, Why were these two threads moved? These are DEV threads. not Gerneal threads. Please move them back.
Thanks!
rhcp0112345 said:
MOD, Why were these two threads moved? These are DEV threads. not Gerneal threads. Please move them back.
Thanks!
Click to expand...
Click to collapse
They don't actually read threads before moving them.. cm6 trolling bs is in dev, but all the active dev threads are getting moved..
The only thing developed in these threads were pictures...
Sent from my SGH-T959 using XDA App
junkdruggler said:
The only thing developed in these threads were pictures...
Sent from my SGH-T959 using XDA App
Click to expand...
Click to collapse
Which would be used by a general user? I dont think so. Why the hell would they care the inside. LOL
These pictures were meant for hardware people. To give ideas.
So i replaced my flex cable with the back and home buttons on it. I had to dissambled my s3 (motherboard, etc). When I put it back together and turned it on the screen is black. It makes the sounds like it turns on and I can swipe the screen and it makes the swipe sound... there is just no display... any ideas? I checked the screen plug on the main motherboard and it seeems to be plugged in snug. Please help!!!
well, how can you expect us to help? you obviously did something wrong, and it's impossible for us to tell exactly what it was. try doing it all over again.
The thread is in the wrong section, General is not for questions. Hit "report" and ask for it to be moved
Glebun said:
well, how can you expect us to help? you obviously did something wrong, and it's impossible for us to tell exactly what it was. try doing it all over again.
The thread is in the wrong section, General is not for questions. Hit "report" and ask for it to be moved
Click to expand...
Click to collapse
Congrats, your post count went up by one. You know if you hit report it does the same thing, and with a lot less effort.
@OP I imagine you damaged something when you dissembled the phone, just to be sure make sure the connectors are seated properly and make sure you haven't missed anything, if you are sure of this you may need to try to find exactly what is damaged to replace it.
I kinda agree with this.
Sent from my GT-I9300 using xda app-developers app
delsus said:
Congrats, your post count went up by one. You know if you hit report it does the same thing, and with a lot less effort.
Click to expand...
Click to collapse
1. I was as helpful as you, you didn't say anything different.
2. You can't report from Tapatalk, and I'd he does it himself he won't do it again
Glebun said:
1. I was as helpful as you, you didn't say anything different.
2. You can't report from Tapatalk, and I'd he does it himself he won't do it again
Click to expand...
Click to collapse
1. Where did I say anything about not being helpful? I was just congratulating you on getting your post count up.
2. you can hit menu, web view and report from there.
Sent from my GT-I9300 using xda premium
Self-appointed mods these days..
delsus said:
1. Where did I say anything about not being helpful? I was just congratulating you on getting your post count up.
2. you can hit menu, web view and report from there.
Sent from my GT-I9300 using xda premium
Click to expand...
Click to collapse
if someone's getting his post count up for no reason, it's you, because you didn't say anything useful, just repeated my advice.
read my second point to the end. I would also have to be logged in in the browser, which I'm not
if you have a problem with me - report me or send a pm, xda is not a place for drama
tytyguy said:
So i replaced my flex cable with the back and home buttons on it. I had to dissambled my s3 (motherboard, etc). When I put it back together and turned it on the screen is black. It makes the sounds like it turns on and I can swipe the screen and it makes the swipe sound... there is just no display... any ideas? I checked the screen plug on the main motherboard and it seeems to be plugged in snug. Please help!!!
Click to expand...
Click to collapse
How did you go about replacing the flex cable? Mine does not work, but LCD and digitizer are fine and trying to figger out how to get a new one in there without killing the screen.
Hi all i am new to this forum and i am ready to learn from you guys
Ok my problem is verry sirius i have send my galaxy to technical lab 3 time
And steel the same.
My phone is beeping by it self. Not after a call not after nothing
He just beeps when he want no body know where or what is the problem
I am with a huge hope that you guys can help me
Thank you all for help
I think thats technical issue. Idk anybody else xperience this but ur problem kinda strange thing to happen and never happen to my phone.
My guess is some kind of RF interference......had new tv recently and kept getting blocks on screen, turned out it was my boiler relay interfering every time the thermostat triggered on/off......and I'm guessing something is causing induction on your speaker in a similar manner
...
Hmmm mey be you right... So what you sugest me to do?
I am agree that this is verry strenge and i didnt know no body with
The same problem.
Thanks for helping me guys
Well if it only happens while you are in a certain location then that would indicate possibly my suggestion, can you describe the beep? Is it a notification beep or does it doing like interference?...or?
..
This is hapening every where.. Its not a notification beep i have
Never hear beep like that... I am now at work in afew hours ill
Come home ill try to record the beep...
It's not what I suggested then, e recording would be very helpful :thumbup:
The system of the forum dont give post links!
I sent you privet masseg but i dont think it will get to you
If not is there other wey i can contact you?
Psyside12 said:
The system of the forum dont give post links!
I sent you privet masseg but i dont think it will get to you
If not is there other wey i can contact you?
Click to expand...
Click to collapse
I got the links but can't play them
Hmmm it recorded from galaxy wonder. And i play them on my s3 you know what is the rison?
I have sent you new links on privet did you get them?
Well it's not a notification sound I recognize, almost sounds like the connection notification when you plug into charge, just wondering if damaged usb port is doing it, but that is just a guess.
Best advice is flash back to stock Rom with full wipe, and before adding your apps see if it's still doing it, if not then add apps a few at a time.
The other thing you could do is run better battery stats and see if that noise links to any wakelocks
slaphead20 said:
Well it's not a notification sound I recognize, almost sounds like the connection notification when you plug into charge, just wonder ing if damaged usb port is doing it, but that is just a guess.
Best advice is flash back to stock Rom with full wipe, and before adding your apps see if it's still doing it, if not then add apps a few at a time.
The other thing you could do is run better battery stats and see if that noise links to any wakelocks
Click to expand...
Click to collapse
Hmmm look my friend the phone was on samsung technical lab 3 times they make a total wipe.
The phone is an original android rom no root done. The s3 i am writing with is rooted but i have 2 s3 one is ok and the second make noise.
dont know what to do
Are you sure it's not one of your apps?
slaphead20 said:
Are you sure it's not one of your apps?
Click to expand...
Click to collapse
Yes i am using regular apps, apps that most of us use they not cracked or somthing
And downloaded from google store... it mey be a mechanik proble? or somthing
With the Motherbord?
Psyside12 said:
Yes i am using regular apps, apps that most of us use they not cracked or somthing
And downloaded from google store... it mey be a mechanik proble? or somthing
With the Motherbord?
Click to expand...
Click to collapse
Anybody's guess really, I'm out of ideas at the moment. Will pm you if anything comes to mind
slaphead20 said:
Anybody's guess really, I'm out of ideas at the moment. Will pm you if anything comes to mind
Click to expand...
Click to collapse
Thank verry much for try help me my friend!!
If any one can help me ill be verry thankfull
Hi
So my ultra was on 40% when i took it off the wireless charger(magnets) and turned it off for the night. when i tried to turn it on it simply didnt do anything. tried the power + vol+ combination but vibrates a few times and thats it. tried to charge it but it shows the red led for a bit then blinks a few times and thats it. no matter what i try to do with it it simply doesnt want to turn on at all......
Pls help to figure it out if there is any hidden secret trick to make it run again....i can even put it on ebay since my data is on it :/
Thank you
knova15 said:
Hi
So my ultra was on 40% when i took it off the wireless charger(magnets) and turned it off for the night. when i tried to turn it on it simply didnt do anything. tried the power + vol+ combination but vibrates a few times and thats it. tried to charge it but it shows the red led for a bit then blinks a few times and thats it. no matter what i try to do with it it simply doesnt want to turn on at all......
Pls help to figure it out if there is any hidden secret trick to make it run again....i can even put it on ebay since my data is on it :/
Thank you
Click to expand...
Click to collapse
did you connect the charger the correct way?
blueether said:
did you connect the charger the correct way?
Click to expand...
Click to collapse
ok lets clear some stuff......this is my 30+ phone in the past 10 years so i know how to use thing ok ? also as far as i know you should not be able to plug the charger in the other way.........
Have you tried charging the phone with the regular micro USB port charging and leave it for some time. Also try pushing the red reset button underneath the right flaps beside the Sim tray.
bushako said:
Have you tried charging the phone with the regular micro USB port charging and leave it for some time. Also try pushing the red reset button underneath the right flaps beside the Sim tray.
Click to expand...
Click to collapse
yes left it on the charger but after a bit it starts flashing red and nothing next time it only flashes red for a bit then nothing....red hard reset button does nothing either :/
knova15 said:
ok lets clear some stuff......this is my 30+ phone in the past 10 years so i know how to use thing ok ? also as far as i know you should not be able to plug the charger in the other way.........
Click to expand...
Click to collapse
Yes, lets clear some stuff up, Ive seen too many xperia's killed with cheap connectors turned the other way to count... Are you really sure you didn't connect it incorrectly?
red flashing LED is a common symptom of killing the charging
blueether said:
Yes, lets clear some stuff up, Ive seen too many xperia's killed with cheap connectors turned the other way to count... Are you really sure you didn't connect it incorrectly?
red flashing LED is a common symptom of killing the charging
Click to expand...
Click to collapse
why are you trying to keep coming up with something crap like that ? you dont even worth a reply....i guess you didnt even fully read my original post BUT lets make life easier :
No it was always used as it should be it was working fine since i had it and yes it was ok when i turned it OFF and never came back on suddenly
Does it get recognized by your pc in fastest mode or flashmode? If not then according to what I've been reading about other xperia devices it's time you send it in to the service center.They've termed it the LED light of death.
knova15 said:
... you dont even worth a reply...
Click to expand...
Click to collapse
You are correct, not worth my time.
I guess over 1000 thankyous and 2 and a half K posts means jack when it comes to XDA, I'll remember that next time I suggest something that I've seen happen
blueether said:
You are correct, not worth my time.
I guess over 1000 thankyous and 2 and a half K posts means jack when it comes to XDA, I'll remember that next time I suggest something that I've seen happen
Click to expand...
Click to collapse
So I should be happy for you to ask me the most blond question about the charger cos u got a lot of thank you? Great…..
Next time ask it simply : did work without any issues before ? are you new to this smartphone stuff ? right away you can determine if you talk to a blond or an older person who is into changing the roms on 99% of his/her phones like clothes. This is the 2nd phone I never touched or rooted as I didn’t need to.
So to finish this off topic thanks for your reply !
And bushako :
Thanks will have a talk with sony tomorrow morning. Im even ok to sell it as for parts on ebay but if someone can retrieve it my data is still on it in offline mode till he/she connects to the net with it :/
What is wrong with you?
knova15 said:
ok lets clear some stuff......this is my 30+ phone in the past 10 years so i know how to use thing ok ? also as far as i know you should not be able to plug the charger in the other way.........
Click to expand...
Click to collapse
knova15 said:
why are you trying to keep coming up with something crap like that ? you dont even worth a reply....i guess you didnt even fully read my original post BUT lets make life easier :
No it was always used as it should be it was working fine since i had it and yes it was ok when i turned it OFF and never came back on suddenly
Click to expand...
Click to collapse
knova15 said:
So I should be happy for you to ask me the most blond question about the charger cos u got a lot of thank you? Great…..
Next time ask it simply : did work without any issues before ? are you new to this smartphone stuff ? right away you can determine if you talk to a blond or an older person who is into changing the roms on 99% of his/her phones like clothes. This is the 2nd phone I never touched or rooted as I didn’t need to.
So to finish this off topic thanks for your reply !
And bushako :
Thanks will have a talk with sony tomorrow morning. Im even ok to sell it as for parts on ebay but if someone can retrieve it my data is still on it in offline mode till he/she connects to the net with it :/
Click to expand...
Click to collapse
Your responses are totally uncalled for and completely disproportionate. Actually they're downright offensive. "Blond" - really?
Blueether is trying to help you with common troubleshooting practices. No one knows (or cares) who you are and what your technical expertise/background is. Even seasoned experts make common mistakes.
Not to mention that Blueether has contributed tremendously to this community. In all likelihood you have benefited from his work in some form or another. I don't think I can say the same about your profile. You were lucky he was willing to take a look at your problem.
No one owes you help. These guys are on here in their spare time with no renumeration. People like you ruin it for everyone else seeking to give/receive assistance.
Hi,
I have the same issue with my Z Ultra c6833, just the red led light when connected to the charger and pc. I dont get any responses to the buttons or any vibration when pressed. Before it died, It still powered on showing me the time and how much battery it has, around 92%. So decided to connect my magnetic charging cable to charge and waiting for the green led light meaning it's charging, but never got the green light and the Ultra never powered up again. Its on the official kitkat rom, not rooted and not a scratch, well babied. Tried charging it over night and the whole day, still just the red led light I get and computer doesn't even recognize it when it's plugged in.
Can I send it for warranty here in canada even though it's the c6833 model? Or can I send it to any service center to have it fix? And how much do you guyz think it will cause me to have it fix?
Thanks in advance for future replies.
Sent from my SM-N900W8 using XDA Free mobile app
rvnteck said:
Hi,
I have the same issue with my Z Ultra c6833, just the red led light when connected to the charger and pc. I dont get any responses to the buttons or any vibration when pressed. Before it died, It still powered on showing me the time and how much battery it has, around 92%. So decided to connect my magnetic charging cable to charge and waiting for the green led light meaning it's charging, but never got the green light and the Ultra never powered up again. Its on the official kitkat rom, not rooted and not a scratch, well babied. Tried charging it over night and the whole day, still just the red led light I get and computer doesn't even recognize it when it's plugged in.
Can I send it for warranty here in canada even though it's the c6833 model? Or can I send it to any service center to have it fix? And how much do you guyz think it will cause me to have it fix?
Thanks in advance for future replies.
Sent from my SM-N900W8 using XDA Free mobile app
Click to expand...
Click to collapse
EDIT: Information given to me below by the online Sony Rep was incorrect. See http://forum.xda-developers.com/showpost.php?p=56814703&postcount=17 for correct info.
Just talked to a Sony rep as I'm interested in buying this phone from the US and wanted to know about warranty etc. Your covered by 1 year manufacturer's but you have to send it to the centre with country of origin. I'm not sure if that means the country you bought it from (which was what I was asking because I wanted to buy it from the States) or the intended region of the phone. If your phone is under warranty (i.e. within a year of purchase) you should be able to get it fixed but you will have to mail it out of the country. If out of warranty I'm not sure -- may be able to get it fixed here.
unidentifier said:
Your responses are totally uncalled for and completely disproportionate. Actually they're downright offensive. "Blond" - really?
Blueether is trying to help you with common troubleshooting practices. No one knows (or cares) who you are and what your technical expertise/background is. Even seasoned experts make common mistakes.
Not to mention that Blueether has contributed tremendously to this community. In all likelihood you have benefited from his work in some form or another. I don't think I can say the same about your profile. You were lucky he was willing to take a look at your problem.
No one owes you help. These guys are on here in their spare time with no renumeration. People like you ruin it for everyone else seeking to give/receive assistance.
Click to expand...
Click to collapse
1st when you cant see someone (personal conversations versus typing)and the first ish help is if i used the charger the right way anyone would go nuts....In the first post i detailed as much as possible to make sure i wont get the "common" resolution options hence they were all tried and failed.
2nd yes it is great but that means he can read too just like you if you read it from the beginning. I would of been lucky if i get the right attitude from the other end too.
3rd i didnt say anyone owe me help. i searched,read,and asked when all failed. in my spare time i run non-profit help and information sites +teaching beginners for free so don't need lessons how to use my spare time. People like you who doesnt read ruin communities to be fair. Read first ask 2nd is what i do and did in the past almost 20 years since i had my 386. so go and read it again and troll somewhere else with you logic.
Thx
rvnteck said:
Hi,
I have the same issue with my Z Ultra c6833, just the red led light when connected to the charger and pc. I dont get any responses to the buttons or any vibration when pressed. Before it died, It still powered on showing me the time and how much battery it has, around 92%. So decided to connect my magnetic charging cable to charge and waiting for the green led light meaning it's charging, but never got the green light and the Ultra never powered up again. Its on the official kitkat rom, not rooted and not a scratch, well babied. Tried charging it over night and the whole day, still just the red led light I get and computer doesn't even recognize it when it's plugged in.
Can I send it for warranty here in canada even though it's the c6833 model? Or can I send it to any service center to have it fix? And how much do you guyz think it will cause me to have it fix?
Thanks in advance for future replies.
Sent from my SM-N900W8 using XDA Free mobile app
Click to expand...
Click to collapse
Hi
I been to about 50 shops nobody were able to fix it nore there was any solution online anywhere The best you can try is to sell it on eBay they will bid it over £100 easily if your screen is in mint condition.
knova15 said:
1st when you cant see someone (personal conversations versus typing)and the first ish help is if i used the charger the right way anyone would go nuts....In the first post i detailed as much as possible to make sure i wont get the "common" resolution options hence they were all tried and failed.
2nd yes it is great but that means he can read too just like you if you read it from the beginning. I would of been lucky if i get the right attitude from the other end too.
3rd i didnt say anyone owe me help. i searched,read,and asked when all failed. in my spare time i run non-profit help and information sites +teaching beginners for free so don't need lessons how to use my spare time. People like you who doesnt read ruin communities to be fair. Read first ask 2nd is what i do and did in the past almost 20 years since i had my 386. so go and read it again and troll somewhere else with you logic.
Thx
Click to expand...
Click to collapse
You're right about one thing: your posts speak for themselves.
rvnteck said:
Hi,
Can I send it for warranty here in canada even though it's the c6833 model? Or can I send it to any service center to have it fix? And how much do you guyz think it will cause me to have it fix?
Click to expand...
Click to collapse
Just to follow up. I bought a device on ebay that stated the location as Memphis. The fedex shipment is actually coming from Singapore.
I chatted with an online rep and further called Sony Canada and they both confirmed that a device under 1 year manufacturer's warranty CAN be given to a Sony Canada Service Centre. The only caveat is that they cannot give a turnaround time (it's usually 2 weeks or something) as they say they may need to get parts from abroad.
I'm not sure how much that would apply for a C6833 as it's more or less the same as the C6806.
But there you have it.
Thanks for the reply Unidentifier
When I called Sony Canada on Nov 9th, they verified my c6833 still under warranty by checking the IMEI number. They emailed me the RMA number and shipping label for Purolator ( Shipping out and back is free, so I didn't spend a penny ) Service Center here in my area in Toronto is in Mississauga.
The rep told me that it will take a little longer than the standard 2 weeks to get it back because the device is an Asian/European version, because there's chances they might order the parts from it's place of origin.
But to my surprise, after they received my c6833 on Nov 12th I got a notice form Purolator last Nov 18th that my device came back from the service center already. So picked it up at the depot, at first I was so worried because I'm thinking maybe they didn't fix it cause it came back to quickly. After inspecting the device and the documents that came back with it, found out that they replaced it with a new Bell c6806 on Kitkat v. 14.4.a.0.108 but unlock, it works with Koodo and Rogers sim.
So all is well now, just not sure if I lost something because they gave me a c6806 instead of my previous c6833.
My only question now is how to prevent this from happening again? My feeling is that the magnetic charging cable is the reason why my device died, maybe that's the reason why Sony never made an official magnetic charging cable. Because there's always high chances you'll attach it in the wrong way. Unlike with the charging dock, it won't go in and connect itself unless it's putted in the right way.
Overall warranty experience with Sony is awesome! ?
unidentifier said:
Just to follow up. I bought a device on ebay that stated the location as Memphis. The fedex shipment is actually coming from Singapore.
I chatted with an online rep and further called Sony Canada and they both confirmed that a device under 1 year manufacturer's warranty CAN be given to a Sony Canada Service Centre. The only caveat is that they cannot give a turnaround time (it's usually 2 weeks or something) as they say they may need to get parts from abroad.
I'm not sure how much that would apply for a C6833 as it's more or less the same as the C6806.
But there you have it.
Click to expand...
Click to collapse
Sent from my SM-N900W8 using XDA Free mobile app
rvnteck said:
Thanks for the reply Unidentifier
When I called Sony Canada on Nov 9th, they verified my c6833 still under warranty by checking the IMEI number. They emailed me the RMA number and shipping label for Purolator ( Shipping out and back is free, so I didn't spend a penny ) Service Center here in my area in Toronto is in Mississauga.
The rep told me that it will take a little longer than the standard 2 weeks to get it back because the device is an Asian/European version, because there's chances they might order the parts from it's place of origin.
But to my surprise, after they received my c6833 on Nov 12th I got a notice form Purolator last Nov 18th that my device came back from the service center already. So picked it up at the depot, at first I was so worried because I'm thinking maybe they didn't fix it cause it came back to quickly. After inspecting the device and the documents that came back with it, found out that they replaced it with a new Bell c6806 on Kitkat v. 14.4.a.0.108 but unlock, it works with Koodo and Rogers sim.
So all is well now, just not sure if I lost something because they gave me a c6806 instead of my previous c6833.
My only question now is how to prevent this from happening again? My feeling is that the magnetic charging cable is the reason why my device died, maybe that's the reason why Sony never made an official magnetic charging cable. Because there's always high chances you'll attach it in the wrong way. Unlike with the charging dock, it won't go in and connect itself unless it's putted in the right way.
Overall warranty experience with Sony is awesome! ?
Sent from my SM-N900W8 using XDA Free mobile app
Click to expand...
Click to collapse
Thank for getting back with the positive story. I wonder if the OP actually did anything to get theirs fixed other than slag me off
blueether said:
Thank for getting back with the positive story. I wonder if the OP actually did anything to get theirs fixed other than slag me off
Click to expand...
Click to collapse
About the question : sent the unit to Sony and they asked for £12 to find out it is dead. When i received it back went to another mobile repair shop just incase and they shown me that whatever they did they actually fried the mobo and cracked it too in the "diagnostics" process. So i took the screen out and sold it on eBay to get back at least some money after all the months of searching reading arguing waitingFORsony etc.
Hi!
To make a long story short, I got my phone nice and wet. After that the only thing that would work is the charging light and "utility" button(flashlight). I disassembled the thing and it had some oxidization goin on. I cleaned as best as I could....Assembled it back and it pretty much does the same thing. Only charges, flashlight works and it doesn't give me haptic feedback but I can browse the phones data storage on my pc...
The reason I'm posting is that do you guys have any insight/experience on similar stuff... I'm somewhat sure its the screen module(digitizer) that doesn't work?
Also, if you have bought those cheap ~30-40€ unbranded replacement modules...are they any good?
You might want to bring it to service center now if oxidation happens. I have a few experience with getting phones wet, but just wet and not soaked like yours. I just let them dry and they are working again.
Sent from my honor 5X using XDA Labs
anatoli_ said:
Hi!
To make a long story short, I got my phone nice and wet. After that the only thing that would work is the charging light and "utility" button(flashlight). I disassembled the thing and it had some oxidization goin on. I cleaned as best as I could....Assembled it back and it pretty much does the same thing. Only charges, flashlight works and it doesn't give me haptic feedback but I can browse the phones data storage on my pc...
The reason I'm posting is that do you guys have any insight/experience on similar stuff... I'm somewhat sure its the screen module(digitizer) that doesn't work?
Also, if you have bought those cheap ~30-40€ unbranded replacement modules...are they any good?
Click to expand...
Click to collapse
Here at XDA, most of us are software geeks so only advice, most of us can give
Service center
basicly if u can browse ur phone so its running , the only thing u can do is start replacing ur screen to get it up to life then u'll start seeing what ever neet to replace so u can replace .
GD Luck .
Romiui said:
basicly if u can browse ur phone so its running , the only thing u can do is start replacing ur screen to get it up to life then u'll start seeing what ever neet to replace so u can replace .
GD Luck .
Click to expand...
Click to collapse
better if he give it to the service center, theyl take care of everything
anatoli_ said:
Hi!
To make a long story short, I got my phone nice and wet. After that the only thing that would work is the charging light and "utility" button(flashlight). I disassembled the thing and it had some oxidization goin on. I cleaned as best as I could....Assembled it back and it pretty much does the same thing. Only charges, flashlight works and it doesn't give me haptic feedback but I can browse the phones data storage on my pc...
The reason I'm posting is that do you guys have any insight/experience on similar stuff... I'm somewhat sure its the screen module(digitizer) that doesn't work?
Also, if you have bought those cheap ~30-40€ unbranded replacement modules...are they any good?
Click to expand...
Click to collapse
Service center is ur best frn now . u can move on bro. ?
Sent from my KIW-L22 using Tapatalk