if sp flash tool cannot detect a specific phone.that mean the phone is dead.or the software is not capatible?
ynj said:
if sp flash tool cannot detect a specific phone.that mean the phone is dead.or the software is not capatible?
Click to expand...
Click to collapse
have u installed USB VCOM DRIVER in ur pc?
is it mediatek device?
jamius19 said:
have u installed USB VCOM DRIVER in ur pc?
is it mediatek device?
Click to expand...
Click to collapse
yes mtk6582.lenovo a850
ynj said:
yes mtk6582.lenovo a850
Click to expand...
Click to collapse
then turn off ur set.....
remove the battery then insert it after 20 seconds or so....
but don't open the set!
plug in the usb cable!
see if something pops up with this messge,
MediaTek USB VCOM Preloader
if its so, then ur device is oky!
otherwise its not recognised by ur pc!
jamius19 said:
then turn off ur set.....
remove the battery then insert it after 20 seconds or so....
but don't open the set!
plug in the usb cable!
see if something pops up with this messge,
MediaTek USB VCOM Preloader
if its so, then ur device is oky!
otherwise its not recognised by ur pc!
Click to expand...
Click to collapse
install everything..i having use mtk device all along..all other device cannot detect also..
ynj said:
install everything..i having use mtk device all along..all other device cannot detect also..
Click to expand...
Click to collapse
What u mean by "all other device cannot detect also"?
Tried other mtk devices?
Do you or do u not see the MediaTek USB VCOM Preloader popup?
SOMETHING U CAN FORGET:
1.Is the VCOM driver is installed according to your windows bit?
2.Are u using the latest version of SP Flash Tool?
jamius19 said:
What u mean by "all other device cannot detect also"?
Tried other mtk devices?
Do you or do u not see the MediaTek USB VCOM Preloader popup?
SOMETHING U CAN FORGET:
1.Is the VCOM driver is installed according to your windows bit?
2.Are u using the latest version of SP Flash Tool?
Click to expand...
Click to collapse
yes.jus realised my phone usb port broken together with jumping wire.
Related
Flash ur phones with "Windows 8 x64"
1) download Usbdeview
http://www.mediafire.com/download/41i2k36yyi1fzhz/usbdeview-x64.zip
2) unistall all the MTK65xx drivers u get in it (remember to use this as admin)
3)Reboot ur PC
4)Download Sp drivers for win8
http://www.mediafire.com/download/7yee2of64nhl947/SP_Drivers_v1.4.rar
5)Now open Device manager (right click on My Computer>Manage>Device manager)
6)Remove the battery and connect the phone via USB u will see unknown device in device manager and then MTK65xx Preloader
7)Quickly Right click on the MTK65xx preloader and update driver go for manual and then give the path for sp tools and just select the folder inside SP tools
8) u will c dialouge box asking for installing here select install anyway
9)and u r done.. u will here sound of disconnected device
10)connect again and u will c your device appearing and dissapearing on COM ports
11) Now open sp flash tools use this 1
http://www.mediafire.com/download/wd8au297r6w9qzd/SP_Flash_Tool_v3.1304.0.119.rar
12)dont forget to open sp tools in admin mode..
13) select the scatter file and make sure u have disconnected ur phone
14) select USB in options and force to high speed
15) Press Firmware Upgrade and then insert USB cable to ur phone
16) Sit back for 5-6 min until u c a green circle on ur screen.
Older drivers work if you Disable Driver Signing Enforcement for installing unsigned drivers.
:angel:
boring method
jatin.rewri said:
boring method
Click to expand...
Click to collapse
Glad to see someone else said it and not me. I flashed TWRP 2.5 with SPTOOLS and Flashed SuperSU 1.32 in TWRP and I was on rooted A116 in less than 3 minutes. Isnt that too fast and simple? Yes works on Win8 64bit too.
cmahendra said:
Glad to see someone else said it and not me. I flashed TWRP 2.5 with SPTOOLS and Flashed SuperSU 1.32 in TWRP and I was on rooted A116 in less than 3 minutes. Isnt that too fast and simple? Yes works on Win8 64bit too.
Click to expand...
Click to collapse
Ya that method is too fast and simple bt many of us faced problems in flashing the device for the first time in win8 64bit even i had to use win xp for rooting for the first time....... its not that all are known to ur method so i just posted this method coz many are still crying coz they r unable to flash the original stock 4.2 rom using spflash tool in win8...........
yes...
Titokhan said:
Older drivers work if you Disable Driver Signing Enforcement for installing unsigned drivers.
:angel:
Click to expand...
Click to collapse
yes man...old drivers works...using win 8 x64....
once u need to boot into Disable Driver Signing Enforcement for installing unsigned drivers.
This method aint working in my system.Can anyone provide the old drivers? The preloader comes up for a split second in the com section in device manager and disappears. Any help?
@deepayanneogi
It happens if you try to install it without starting SP Flash Tool first.
What I mean to say is the flash mode persists under Windows only if SP Flash Tool is open. So open SP Flash Tool, connect the mobile, install the driver & then flash it.
Connect your phone without battery and then keep pressing volume down button then you will here sound on your system.... Then reconnect device and you will find it in device manager then install drivers
Sent from my Micromax A116 using xda premium
It worked great and now can root or flash roms by using windows 8 x64 but for installing driver i have to reboot my pc into driver enforcement mode...........
Sent from my Micromax A116 using xda premium
i was trying to root my phone so i flash my device with TWRP recovery using Rashr app.
after rebooting my phone storage need format. i rebooted my phone without formatting and then it stuck on boot logo .
then i used SP flash tools for flashing stock recovery but it gave an error and stops and after that my device is not responding to any key combination but my laptop is detecting device when i insert it .
Please help.
Xolo 8X-1000 [battery non removable]
MTK6592M
Need some details
1.What is your phone model?
2.Which chipset your phone have?
3.I guess you have scatter file but how did you get that? from stock rom?
Phone model?
If it detects Preloader of device you are good to go
If not you need full backup of stock rom and install drivers
aravazhi_mdr said:
1.What is your phone model?
2.Which chipset your phone have?
3.I guess you have scatter file but how did you get that? from stock rom?
Click to expand...
Click to collapse
XOLO 8X-1000
MediaTek MTK6592M
and i downloaded stock ROM from androidmtk .com
thank you for your help
Scot can u run device manager and take a screenshot of Com ports when u connect ur device?
arshad145 said:
Scot can u run device manager and take a screenshot of Com ports when u connect ur device?
Click to expand...
Click to collapse
device is detectable by laptop as Mediatek DA USB VCOM port in device manager.
bad ...
It must be detected as preloader mt65xx
Don't panic
1.Disconnect phone take battery out or switch it off
2.Connect device to pc via usb without battery
Post result...
arshad145 said:
bad ...
It must be detected as preloader mt65xx
Don't panick
1.Disconnect phone take battery out or switch it off
2.Connect device to pc via usb without battery
Post result...
Click to expand...
Click to collapse
battery is non removable
switch off phone then...
Disconnect usb then reconnect with phone off
Result?
---------- Post added at 01:07 ---------- Previous post was at 01:06 ----------
And btw wat version of windows running? 7,8,10?
Good forgive my English but this translated into google translate
my problem is the next
My Sony xperia z5 does not turn on after a bad flashing with flash tool
It does not turn on, the red LED does not either, the screen goes black
MTK USB Port (COM11)
With flash tool start red bar but stops with error 4032
I do not have more device features
If anyone has any way to solve this problem would be of great help
rednaxela2 said:
Good forgive my English but this translated into google translate
my problem is the next
My Sony xperia z5 does not turn on after a bad flashing with flash tool
It does not turn on, the red LED does not either, the screen goes black
MTK USB Port (COM11)
With flash tool start red bar but stops with error 4032
I do not have more device features
If anyone has any way to solve this problem would be of great help
Click to expand...
Click to collapse
I think you hard bricked your Android. Is it your Android running on Qualcomm processor. If yes then unbrick your Android using tool studio tool.
Ashwinrg said:
I think you hard bricked your Android. Is it your Android running on Qualcomm processor. If yes then unbrick your Android using tool studio tool.
Click to expand...
Click to collapse
I can not understand your question
rednaxela2 said:
I can not understand your question
Click to expand...
Click to collapse
I mean which chipset your Android running.
Ashwinrg said:
I mean which chipset your Android running.
Click to expand...
Click to collapse
You are referring to if it is working, I do not know if it is at best if what I can tell you is that the pc recognizes the device usb
rednaxela2 said:
You are referring to if it is working, I do not know if it is at best if what I can tell you is that the pc recognizes the device usb
Click to expand...
Click to collapse
Which port PC recognizes when you connect usb
Ashwinrg said:
Which port PC recognizes when you connect usb
Click to expand...
Click to collapse
MTK USB Port (COM11)
rednaxela2 said:
MTK USB Port (COM11)
Click to expand...
Click to collapse
Go to meta mode and flash your stock rom using SP flash tool.
Ashwinrg said:
Go to meta mode and flash your stock rom using SP flash tool.
Click to expand...
Click to collapse
Flash tool error 4032
Help me guys.. My RN4 mtk 3/64 MIUI Global 8.0.3.0 unlockbootloader suddently dead.. No led, no vibrate. My pc detect as mtk usb port..but connection not stable
.. Connect-disconnect repeatly. And SPFT can't work.. Can't format, can't readback, can't flash.. Always stuck at 100% red bar and ERROR : STATUS_DA_HASH_MISMATCH for rom miui 8 china or global stable.. And ERROR : STATUS_EXCEED_NUM_MAX for rom global dev and china dev..please give me solution :crying::crying:
Thanks..
Can you get into the bootloader to use fastboot? Does that much work? If not, you may be in trouble
Also, are you positive you have the MTK driver installed correctly? I remember there being driver verification issues with Win10.
smokinjoe2122 said:
Can you get into the bootloader to use fastboot? Does that much work? If not, you may be in trouble
Also, are you positive you have the MTK driver installed correctly? I remember there being driver verification issues with Win10.
Click to expand...
Click to collapse
Can not enter fastboot or recovery mode .. I am using win 7 64bit .. And for the mtk driver I've tried to install repeatedly from various sources and in various ways but the result is the same.
arilevint said:
Help me guys.. My RN4 mtk 3/64 MIUI Global 8.0.3.0 unlockbootloader suddently dead.. No led, no vibrate. My pc detect as mtk usb port..but connection not stable
.. Connect-disconnect repeatly. And SPFT can't work.. Can't format, can't readback, can't flash.. Always stuck at 100% red bar and ERROR : STATUS_DA_HASH_MISMATCH for rom miui 8 china or global stable.. And ERROR : STATUS_EXCEED_NUM_MAX for rom global dev and china dev..please give me solution :crying::crying:
Thanks..
Click to expand...
Click to collapse
If your repeatedly getting disconnect/reconnect I would suggest you use another USB cable or USB port because that's not normal.
If not then it may be a driver/PC issue.
Sent from my Redmi Note 4 using Tapatalk
Wilderone said:
If your repeatedly getting disconnect/reconnect I would suggest you use another USB cable or USB port because that's not normal.
If not then it may be a driver issue.
Sent from my Redmi Note 4 using Tapatalk
Click to expand...
Click to collapse
Ok..I'm going to buy a new cable.
Still unresolved. I try memory test SPFT can run normally. Device manager detects as MediaTek DA vcom usb .. But if I format or flashing error message appears again .. STATUS_DA_HASH_MISMATCH.
Perhaps try downloading different firmware if you're getting a hash error?
I still think getting into fastboot is important...Since Official MIUI doesn't have a real recovery, you're better off installing TWRP and seeing if you can do something from within recovery.
arilevint said:
Still unresolved. I try memory test SPFT can run normally. Device manager detects as MediaTek DA vcom usb .. But if I format or flashing error message appears again .. STATUS_DA_HASH_MISMATCH.
Click to expand...
Click to collapse
Is your Rn4 a mtk device or snapdragon device???? Please check.
If it is mtk then u would require scatter file along with correct firmware.
And if it is a snapdragon device, u can flash most of the things through bootloader mode.
Hope it helps.
subodhverma21 said:
Is your Rn4 a mtk device or snapdragon device???? Please check.
If it is mtk then u would require scatter file along with correct firmware.
And if it is a snapdragon device, u can flash most of the things through bootloader mode.
Hope it helps.
Click to expand...
Click to collapse
Im sure my device xiaomi redmi note 4 mediatek 3/64gb with logo china mobile in back casing.
arilevint said:
Im sure my device xiaomi redmi note 4 mediatek 3/64gb with logo china mobile in back casing.
Click to expand...
Click to collapse
Working with MTK devices is bit tricky.
though you will get success, i Hope
If you are sure that your device is MTK, then ofcourse your bootloader mode will not work. So try to adopt this solution:
1. Get SPFlash Tool, the latest one. http://spflashtool.com/
2. Get MediaTek USB VCOM drivers. http://spflashtool.com/
3. Now most important Get your Original Firmware along with the Scatter file. The SPflashtool only recognizes the scatter file. So you need ROM along with scatter file.
check this link and follow the instructions http://en.miui.com/thread-370620-1-1.html
check your ROM if it is here. Only Use the correct firmware for your devices otherwise you may do a permanent damage to your device. http://en.miui.com/download-309.html#454
Hope it helps.
Hi i have the same problem, spft always give me an error, i cannot enter in fastboot or recovery, did you solve the problem?
have you flashed preloader or had you selected "Format all and Download"? If not, or maybe yes,, try to flash custom cust.img and just plug in your phone without holding vol-down button. Also make sure that you disable driver signature enforcement. Anyway it sounds scary as I reflash my fastboot firmware on SP Flash Tool ocasionally after using twrp.
---------- Post added at 06:14 PM ---------- Previous post was at 06:12 PM ----------
If it doesn't work,, have a motherboard replacement
hello i managed to flash with sp flash tool but after flashing it is not charging and couldnt be powered on. i have held the power button for more than 20 secs
jr1945 said:
hello i managed to flash with sp flash tool but after flashing it is not charging and couldnt be powered on. i have held the power button for more than 20 secs
Click to expand...
Click to collapse
go to help at care centre buddy it look like a serious problem
subodhverma21 said:
Working with MTK devices is bit tricky.
though you will get success, i Hope
If you are sure that your device is MTK, then ofcourse your bootloader mode will not work. So try to adopt this solution:
1. Get SPFlash Tool, the latest one.
2. Get MediaTek USB VCOM drivers.
3. Now most important Get your Original Firmware along with the Scatter file. The SPflashtool only recognizes the scatter file. So you need ROM along with scatter file.
check this link and follow the instructions
check your ROM if it is here. Only Use the correct firmware for your devices otherwise you may do a permanent damage to your device.
Hope it helps.
Click to expand...
Click to collapse
i stuck in (Vol -) ,( Vol - and power button )and plug in USB. red bar not appear in SP tool, why it happen? please help
chimouw said:
i stuck in (Vol -) ,( Vol - and power button )and plug in USB. red bar not appear in SP tool, why it happen? please help
Click to expand...
Click to collapse
are you able to go to VCOM mode?
you have to go to VCOM mode in the MTK device to use the SP Flash Tool.
1. Install Vcom drivers from internet.
2. Phone will get detected. Then the SP Flash Tool will Run
Hope it helps.
subodhverma21 said:
are you able to go to VCOM mode?
you have to go to VCOM mode in the MTK device to use the SP Flash Tool.
1. Install Vcom drivers from internet.
2. Phone will get detected. Then the SP Flash Tool will Run
Hope it helps.
Click to expand...
Click to collapse
I finally installed mediatek driver but it didn't give any progress, btw test point can work??
chimouw said:
I finally installed mediatek driver but it didn't give any progress, btw test point can work??
Click to expand...
Click to collapse
Do you have the scatter file?
where did you get the scatter file?
Which SPF tool are you working with?
Download the latest SPFT and then try.
hope it helps.
subodhverma21 said:
Do you have the scatter file?
where did you get the scatter file?
Which SPF tool are you working with?
Download the latest SPFT and then try.
hope it helps.
Click to expand...
Click to collapse
I has scatter file from en. Miui /a-234 with codename nikel, I used spf tool the latest version.
Otherwise, my phone can not detected in my pc, neither unknown device or Vcom statuse. How should I do again? With test point or DFC can work??
Really my phone is Deep Death, before DD I flashed with snap dragon rom, result is DD
chimouw said:
I has scatter file from en. Miui /a-234 with codename nikel, I used spf tool the latest version.
Otherwise, my phone can not detected in my pc, neither unknown device or Vcom statuse. How should I do again? With test point or DFC can work??
Really my phone is Deep Death, before DD I flashed with snap dragon rom, result is DD
Click to expand...
Click to collapse
Have patience, it should not be problem.
Is your battery removable?
If yes, take it out. Unplug usb.
Plug usb again with battery out. Press -vol to detect vcom driver.
Most important , adb driver or usb debugging mode should not be enabled. Otheewise the vcom drivers will not install.
Once vcom mode works. SPFT will work on its own.
Hope it helps.
I was just trying to install MediaTek MT65xx USB VCOM Drivers on Windows 10 to Flash firmware in my Android phone,
But it is returning me Error code 10.
The drivers are not working too,
Please give me it's solution as soon as possible...
Thanks...
This error isn't returned by MT65xx USB VCOM Driver. I suppose it's returned by SP Flash Tool. Please be more precise if you want to get helped.
jwoegerbauer said:
This error isn't returned by MT65xx USB VCOM Driver. I suppose it's returned by SP Flash Tool. Please be more precise if you want to get helped.
Click to expand...
Click to collapse
I don't know who returns it,
Btw, here is the error in the image I attached,
When I try to flash firmware using Sp Flash Tool, it returns me error: STATUS_BROM_CMD_SEND_DA_FAIL (0xC0060003)
And I read from another xda problem,
That this error seemed to be occur when MediaTek MT65xx USB VCOM Drivers(MediaTek DA USB VCOM Port Drivers) are not installed correctly...
That's what I know, and no doubt you have more knowledge than that I have, So please clear my concepts if wrong and give me its solution... please...
Mr. Stranger 404 said:
I don't know who returns it,
Btw, here is the error in the image I attached,
When I try to flash firmware using Sp Flash Tool, it returns me error: STATUS_BROM_CMD_SEND_DA_FAIL (0xC0060003)
And I read from another xda problem,
That this error seemed to be occur when MediaTek MT65xx USB VCOM Drivers(MediaTek DA USB VCOM Port Drivers) are not installed correctly...
That's what I know, and no doubt you have more knowledge than that I have, So please clear my concepts if wrong and give me its solution... please...
Click to expand...
Click to collapse
First off, go to Control Panel > Device Manager while your device is connected. Right-click the device and uninstall device.
This will also uninstall any associated existing drivers from your computer.
Once this is done, reboot the computer, connect the device again and try these drivers: https://drive.google.com/file/d/1qVmxaQxddvPRjEKHjQVjj3Eo_cawSE9C/view
DJBhardwaj said:
First off, go to Control Panel > Device Manager while your device is connected. Right-click the device and uninstall device.
This will also uninstall any associated existing drivers from your computer.
Once this is done, reboot the computer, connect the device again and try these drivers: https://drive.google.com/file/d/1qVmxaQxddvPRjEKHjQVjj3Eo_cawSE9C/view
Click to expand...
Click to collapse
I tried installing the drivers you provided, changed the version of sp flash tool, but nothing worked, same error occurred every time...
Mr. Stranger 404 said:
I tried installing the drivers you provided, changed the version of sp flash tool, but nothing worked, same error occurred every time...
Click to expand...
Click to collapse
What's your full device brand/model? What's Windows OS version?
Mr. Stranger 404 said:
When I try to flash firmware using Sp Flash Tool, it returns me error: STATUS_BROM_CMD_SEND_DA_FAIL (0xC0060003)
Click to expand...
Click to collapse
Means SP Flash Tool is unable to read from and/or write to device
Mr. Stranger 404 said:
I tried installing the drivers you provided, changed the version of sp flash tool, but nothing worked, same error occurred every time...
Click to expand...
Click to collapse
Try changing the cable or the port. Preferably USB 2.0. And as @jwoegerbauer asked, please provide more details about the device itself and the Windows version being used.
jwoegerbauer said:
Means SP Flash Tool is unable to read from and/or write to device
Click to expand...
Click to collapse
Yeah...
jwoegerbauer said:
What's your full device brand/model? What's Windows OS version?
Click to expand...
Click to collapse
I use tecno spark 4 kc2,
Trying to flash on Windows 10...