Hi,
I try to connect my z2 tablet to 2 different routers which deliver a "300Mbps" signal (150mbps in fact, verified with a PC).
The maximum speed connection is limited to 75mbps on the tablet (which is very close from the router).
We can see : "Wi-Fi 802.11 a/b/g/n/ac, Wi-Fi Direct, dual-band, DLNA, Wi-Fi hotspot" in the specifications, is there something that i don't understand ?
Thanks
berbar38 said:
Hi,
I try to connect my z2 tablet to 2 different routers which deliver a "300Mbps" signal (150mbps in fact, verified with a PC).
The maximum speed connection is limited to 75mbps on the tablet (which is very close from the router).
We can see : "Wi-Fi 802.11 a/b/g/n/ac, Wi-Fi Direct, dual-band, DLNA, Wi-Fi hotspot" in the specifications, is there something that i don't understand ?
Thanks
Click to expand...
Click to collapse
I have the same issue with mine. I haven't tried changing any router channels or settings yet. Using my galaxy s5 and Z2 tablet from the same location I get around 270mbps on the s5 and only 75 on the Z2.
Dual-band means: 2.4 GHz as well as 5Ghz Wifi. (Either / or, not at the same time.)
In any case the Wifi is restricted to 150 mbps.
Go into your router settings and look for a setting called "HT 20/40 Coexistence" and disable it (in dlink routers it's in Advanced > Advanced wireless). This worked for me when I had a similar issue.
degraaff said:
Go into your router settings and look for a setting called "HT 20/40 Coexistence" and disable it (in dlink routers it's in Advanced > Advanced wireless). This worked for me when I had a similar issue.
Click to expand...
Click to collapse
I've tried before and it's not the solution. My wifi network is on the 40mhz frequency and i can have 150 mbps on a pc but still 75mbps on with the z2.
Actually now I just tested my z2 tablet's wifi speed, and it doesn't seem to go above 56 Mb/s (link speed for the connection in wifi settings is rated at 72 Mb/s), on my PC I reach my ISP's advertised 120 Mb/s. Odd stuff.
I found out that the tablet is unable to get above 72mbps link speed on a 2.4 GHz signal. When using a 5 GHz signal, the link speed leaps to 135 mbps (with a floor/ceiling between the access point and tablet). Maybe for some reason the tablet is unable to use the 40 MHz channel with 2.4 GHz?
Related
I looked into other topics on this forum and didn't find an answer so I hope someone could help me out.
I want to share my PC Broadband Connection through a wireless device (MSI US60SE) so I can browse internet on my LG O1 when I'm at home. I am aware things might be easier with a WiFi router ... but far as it goes this is what I tried, not looking fwd to buy a wireless router at the moment.
Over Broadband Connection > Properties > Sharing I selected "Allow other network users to connect through this computer's Internet connection" and over > Home networking connection < I selected "Wireless connection" and I hit OK.
I set up an ad-hoc internet sharing with a name and password WEP2.
I activated the connections... broadband and ad-hoc. For the 2nd one there was a note "Awaiting connections" a green light was blinking ... so it was on...
I activated the WiFi on my LG O1 P500 and surprise.... there was no sign of my ad-hoc sharing connection. I tried to add it... and there was a note "Not in range"
MSI US60SE is an USB wireless adapter, 802.11b/g, 108Mbs and far as I know Optimus One P500 has WiFi 802.11b/g
Here are some info about the MSI:
Networking
Connectivity Technology Wireless
Data Link Protocol IEEE 802.11b, IEEE 802.11g, 802.11 Super G
Spread Spectrum Method OFDM, DSSS
Data Transfer Rate 108 Mbps
Line Coding Format DBPSK, DQPSK, CCK, OFDM
Frequency Band 2.4 GHz
Max Range Open Space 830 m
Compliant Standards IEEE 802.11b, IEEE 802.11g, IEEE 802.1x
Encryption Algorithm AES, 128-bit WEP, 64-bit WEP, 152-bit WEP, TKIP, WPA, WPA2
Compliant Standards CE, FCC
If I would want to connect my PC through the MSI US60SE I can see the same WiFi (locked) connection I get on my P500
Can anyone explain if I messed up somewhere or if the US60SE is capable of acting as a WiFi router so I could share my PPOE via US60SE to connect my P500
Thanks!
Dude by default android doesn't. Search in the forum you will find a post with a zip file flash it and u can see the adhoc network. Or if using win7 use connnectify
Sent from my LG-P500 using XDA App
Thanks for the tip... I got the answer here. I didn't search using adhoc... well my O1 runs Froyo 2.2.2 and I need to root, for that need to downgrade to 2.2.0... so guess is easier to get a WiFi router or go out downtown fishing for unsecured connections )
Hi guys, anyone can help me out here with regards to connecting our SGS2 to Wireless N network? I have tried changing my radio frequency setting and even resorted to using WEP authentication instead of WPA, but I just can't get the phone to connect via N network, it always connects via G instead. But under the same settings, I am able to connect my acer laptop and my wife's iphone4 to the N network.
Is there any specific settings I need to configure on my router? I am using a Prolink H5004N adsl2+ modem with wireless N router. The modem is compliant to IEEE 802.11n standards, not draft-n and should work with the SGS2?
wind79 said:
Hi guys, anyone can help me out here with regards to connecting our SGS2 to Wireless N network? I have tried changing my radio frequency setting and even resorted to using WEP authentication instead of WPA, but I just can't get the phone to connect via N network, it always connects via G instead. But under the same settings, I am able to connect my acer laptop and my wife's iphone4 to the N network.
Is there any specific settings I need to configure on my router? I am using a Prolink H5004N adsl2+ modem with wireless N router. The modem is compliant to IEEE 802.11n standards, not draft-n and should work with the SGS2?
Click to expand...
Click to collapse
Not sure, but I think that it will connect if your N-network are in the 2.4 GHz frequency area, but not in the 5.0 GHz
mljjlm said:
Not sure, but I think that it will connect if your N-network are in the 2.4 GHz frequency area, but not in the 5.0 GHz
Click to expand...
Click to collapse
Yup, tried that too, but still connects to G only. I have also tried configuring router to accept only N networks instead of G/N, but then the SGS2 will not even see the SSID when its performing a wireless scan.
wind79 said:
connecting our SGS2 to Wireless N network?
Click to expand...
Click to collapse
Ive got the same issue. Router Asus RT-N16 (b/g/n, 2.4GHz). Playing with different router firmwares, settings and so on - no luck so far.
Check the "advanced" settings by pressing the menu button in the wireless and make sure nothing wierd is set in there.
Otherwise, as long as the router is set to N only on the 2.4ghz band, it should at _least_ see the SSID.
That modem supports WPS, try pressing the WPS button on the back of the modem and then use the "WPS button connection" option in the wi-fi settings menu on the SGS2.
Remember the single-channel 802.11n 2.4ghz such as the SGS2 supports will only max out at 72mbps anyway so there's not a huge improvement over the 54mbps that 11g will give you, although 11n is more efficient.
grey77 said:
Ive got the same issue. Router Asus RT-N16 (b/g/n, 2.4GHz). Playing with different router firmwares, settings and so on - no luck so far.
Click to expand...
Click to collapse
I've got the same unit and it works fine with it, that said I'm running a recent build of the Tomato firmware on mine. I don't think I even powered it up fully with the original firmware...
knightnz said:
Check the "advanced" settings by pressing the menu button in the wireless and make sure nothing wierd is set in there.
Otherwise, as long as the router is set to N only on the 2.4ghz band, it should at _least_ see the SSID.
Click to expand...
Click to collapse
thx for fast reply
SGS2 can see SSID, but fails to connect until I force RT-N16 (with custom firmware, RT-N16-1.9.2.7-rtn-r3121) down to "Use 802.11 G only".
Never had any problems with other 802.11 N powered devices.
only wpa2-aes or no encryption are N-standard
wind79 said:
Hi guys, anyone can help me out here with regards to connecting our SGS2 to Wireless N network? I have tried changing my radio frequency setting and even resorted to using WEP authentication instead of WPA, but I just can't get the phone to connect via N network, it always connects via G instead. But under the same settings, I am able to connect my acer laptop and my wife's iphone4 to the N network.
Click to expand...
Click to collapse
wireless N only officially supports either WPA2-AES encryption or no encryption. Devices with drivers that more closely comply to the spec will not connect to WEP or WPA.
I hope you fixed the issue. I stumbled across this thread while asking the same question; maybe someone else will benefit by having this thread wrapped-up also. No haters, egos, persons, etc please. It's been necessary already to block a few of you.
I am not able to connect my Transformer Prime with my new Asus N66U router. I tried all channels and security settings and it only connected when to the router with open system setting. I am able to connect it to my old Netgear WDR3700 in good speed without any problems. Does anyone run into similar situation?
I have the rt-n66u router as well and never had a problem. Are you sure you are using the right encryption settings, Do other devices connect, have you updated the router's firmware? There was a new update just today.
http://support.asus.com/download.as...T-N66U (VER.B1)&os=&hashedid=PZkFHlMrGWzVROxT
have you ensured your router has the latest firmware?
I have the N56u model and no issues.
Yes, I have the latest firmware. My Galaxy Nexus connects just fine. The Transformers Prime actually see the router with strong signal. It just refuses to connect to it. BTW I set the router using WPA-PSK.
Is your prime running the latest update? Or, have you tried DD-WRT?
I have the latest firmware in both devices. However, my Prime is the first batch and may suffers from wifi issues. I may have to try Tomato or Dd-wrt firmware.
Sent from my Galaxy Nexus using Tapatalk 2
Some routers let you disable the broadcasting of the network name (SSID). Computers/network cards that conform correctly with the 802.11 specification will refuse to connect. Have you checked the settings for both 2.4 and 5GHz? - of course the router should not allow disabling of the SSID!
odd. Try wiping the data. Small pin hole in back of router. Reset it. Then 192.168.1.1. go in there and reenter your SSID etc on wireless.
For ****s and giggles. Pump up your 80mw Tx power of wireless to around 160mw. I been running 160mw tx power for awhile and have not and any problems. This baby can go all the way up to 500mw. Of course that is U.S. FCC range limit. With 500mw you can see your wireless from few blocks away.
If your prime is connecting to your other wireless router. Then has to do with some setting in on the RTN66U. Hopefully the wipe will clear any setting in the firmware.
Forgot to mention. Your prime will only connect to the 2.4ghz. It won't connect to the 5ghz wireless.
Did that already. My Transformer does see the 2.4 Ghz SSID with very strong signal. It just keeps reconnecting and fails to connect again eventually. My Galaxy Nexus can connect in a very good speed. Change back to my old Netgear WDR3700 and my transformer connects to it right away. It seems to me that the problem is the security encryption as connection is established right away in open system. However, it just refuse to connect on whatever setting I tried.
ariesting said:
Did that already. My Transformer does see the 2.4 Ghz SSID with very strong signal. It just keeps reconnecting and fails to connect again eventually. My Galaxy Nexus can connect in a very good speed. Change back to my old Netgear WDR3700 and my transformer connects to it right away. It seems to me that the problem is the security encryption as connection is established right away in open system. However, it just refuse to connect on whatever setting I tried.
Click to expand...
Click to collapse
What are the WiFi standards on the Router set to?
Sometimes when a router is set to b/g/n (all combined) it can lead to issues.
I generally keep mine at b/g (no n) on the 2.4 Mhz band, since my n devices run on my router's 5 Ghz band anyway. Try that out.
I tried "auto", "legacy" and "n only" with or without "b and g protection" but still could not connect to the router in any combinations. Will like to know the feedback from anyone who put Tomato on N66U.
If you have kept the same SSID as your old router did you delete the old network settings for that SSID in your TP? Also try a new SSID on the router.
If the router supports WiFi Multimedia (WMM) try disabling it and re-enable it after a connection has been made.
I presume you would know if you had enabled an allowed devices table -MAC addresses. The only other thing I can think of is the size of the "hello I'm here" beacon that the router transmits is too long for the TP and I think that would only be an issue with a very long SSID
Yes, I do keep the old SSID. However, I did forget the network and reconnect to it again in Transformer. My SSID is less than 10 characters. It seems to me that the Transformer is not able to get an IP nor pass the authentication stage.
ariesting said:
Did that already. My Transformer does see the 2.4 Ghz SSID with very strong signal. It just keeps reconnecting and fails to connect again eventually. My Galaxy Nexus can connect in a very good speed. Change back to my old Netgear WDR3700 and my transformer connects to it right away. It seems to me that the problem is the security encryption as connection is established right away in open system. However, it just refuse to connect on whatever setting I tried.
Click to expand...
Click to collapse
Well. Go under advanced settings and then Wireless.
Wireless -General tab.
Frequency click (2.4ghz).
Your SSID (name).
Hide SSID = (No)
Wireless Mode put in (N Only).
Control Channel (1).
Channel Bandwidth (20mhz).
Authentication Method (WPA2-Personal).
WPA Encryption (AES).
Enter your WPA Pre-Shared Key (password for SSID).
Network Key Rotation Interval to (0).
Wireless -Professional Tab
Frequency (2.4ghz)
Enable Radio (yes)
Date to Enable Radio (Check all days)
Set AP Isolatd (No)
Multicast Rate (Disable)
RTS (2347)
DTIM (3)
Beacon (100)
Enable TX burst (Enable)
Enable Wireless Multi (Disable)
Enable WMM (Enable)
Tx Power adjustment (80)
Try those settings. See what happens.
Will try it as soon as I get back home. Thanks.
I am finally able to get my Transformer connecting to my RT-N66U router by changing the SSID to a new one. The speed and range are not better to my old Netgear WDR3700 though. Thanks for all the help anyway.
ariesting said:
I am finally able to get my Transformer connecting to my RT-N66U router by changing the SSID to a new one. The speed and range are not better to my old Netgear WDR3700 though. Thanks for all the help anyway.
Click to expand...
Click to collapse
Good to hear!
I've had the occasional connectivity problem with mine, on certain routers I can get connection but no online connectivity.
some routers use a nonstandard DHCP range (i think it may the ones that utilise 192.168.1.x) anyway, if you encounter this it's simple to correct once you know you simply define a manual ip on the prime for that connection and voila! :>
ariesting said:
I am finally able to get my Transformer connecting to my RT-N66U router by changing the SSID to a new one. The speed and range are not better to my old Netgear WDR3700 though. Thanks for all the help anyway.
Click to expand...
Click to collapse
Cool. Glad you got it working.
Well you can always try and pump your TX power adjustment from the default 80 to 160 or more. I was able to increase my range. I think the max is like 500mw the chip is rated at. However, I havent tried that high. I don't want to burn out my chip. Plus heat increases dramatically at those higher mw's. You would have to toss a little laptop cooler underneath it. (run via the routers usb port there).
My connection problem happens again. Just in case someone has similar issue, I solve the problem by exchanging a new one from store.
ariesting said:
I am not able to connect my Transformer Prime with my new Asus N66U router. I tried all channels and security settings and it only connected when to the router with open system setting. I am able to connect it to my old Netgear WDR3700 in good speed without any problems. Does anyone run into similar situation?
Click to expand...
Click to collapse
I have the n66u too and have no issues.
Hi! I've replaced a router to Asus RT-N56U and my Photon can't see neither standard, nor 5GHz wi-fi networks. I have googled that the router may use higher channels of Wi Fi (12-13) while some devices only scan for channels 1-11. After I tried changing the channel from Auto to no. 5 - the network became visible right away.
I'm on stock 2.3.4 ROM currently. Is there any fix for WiFi module (drivers?) on MoPho so it scans channels 12 and 13?
Thanks in advance!
I was quite surprised to see there is no configuration to choose 2.4ghz or 5ghz, on top of this I cant find a way to view the current band in use. Why make a dual band phone where 5ghz is effectively disabled?
I then read that the option used to exist in 4.0 but was removed in 4.1 and someone made this app.
http://forum.xda-developers.com/showthread.php?t=1891970
Now this app works, I can now use 5ghz which more than doubles my wireless speed, great right?
Well its ok but it resets to 2.4ghz everytime wifi is turned on again, so the setting doesnt stick. So basically everytime I use wifi I have to open the app and select 5ghz. Even the app itself doesnt report what band is in use, it just allows you to select the band to use.
Is there a way to (a) easily see what band is in use and (b) set 5ghz as the default.
Thread moved to porper forum.
I have tried giving 5ghz its own wireless ssid so seperate from 2.4ghz but then its much slower. It seems when the ssid is shared, it uses some kind of parallel mode where both can be used at the same time.
So what I want is when 2.4ghz and 5ghz share the same ssid and the phone connects to 5ghz. (preferably via an option on the phone).