My buddies rooted i717 with CM10 4.2 has been running great. Then it started to turn just turn off on it's own. Last time it turned off now it won't turn on.
When you hit the power samsung logo flashes normally then screen goes blank. At this point it keeps making that powering on vibrating sensation repeatedly. Touch power button and this routine repeats.
It will not boot into recovery. After the sammy logo flash continuing to hold down power +/- does not yield recovery mode. It just starts the vibrating loop.
I thought I will just install stock via kies or flash JB via odin. Well odin mode turns on ok but shuts off after barely 2 to 3 seconds. I have tried this with and without battery, plugged in and not plugged in on pc but end up the same way.
I have checked battery, same is super aok. I swapped batteries with my i717 and mine turns on just fine all the way. My buddy doesn't mind any which way the phone comes back to life.
jayinc11 said:
My buddies rooted i717 with CM10 4.2 has been running great. Then it started to turn just turn off on it's own. Last time it turned off now it won't turn on.
When you hit the power samsung logo flashes normally then screen goes blank. At this point it keeps making that powering on vibrating sensation repeatedly. Touch power button and this routine repeats.
It will not boot into recovery. After the sammy logo flash continuing to hold down power +/- does not yield recovery mode. It just starts the vibrating loop.
I thought I will just install stock via kies or flash JB via odin. Well odin mode turns on ok but shuts off after barely 2 to 3 seconds. I have tried this with and without battery, plugged in and not plugged in on pc but end up the same way.
I have checked battery, same is super aok. I swapped batteries with my i717 and mine turns on just fine all the way. My buddy doesn't mind any which way the phone comes back to life.
Click to expand...
Click to collapse
If you read and run any kind of search, you would find similarities to the all common stuck power button.
Flick tye back of the phone a few times.
I know, you can feel it click.......doesnt matter, flick the phone.
If you are brave enough, you can open phone and clean with qtip and alcohol.
I am not.
Sent from my SAMSUNG-SGH-I527 using XDA Free mobile app
I did actually, it didn't work. I thought there's was something that could help before I have to open it up cause of time. I change ports, cameras, etc on these models so it's not a biggie to clean it. Will do this this weekend.
jayinc11 said:
I did actually, it didn't work. I thought there's was something that could help before I have to open it up cause of time. I change ports, cameras, etc on these models so it's not a biggie to clean it. Will do this this weekend.
Click to expand...
Click to collapse
There have been multiple times that I couldn't get into recovery mode, but download mode worked fine.... I just reinstalled CWM and reflashed.
May not help the root cause, but may get you past the no-recovery mode issue.
morgandc said:
There have been multiple times that I couldn't get into recovery mode, but download mode worked fine.... I just reinstalled CWM and reflashed.
May not help the root cause, but may get you past the no-recovery mode issue.
Click to expand...
Click to collapse
Neither works. DL mode turns off after 2-3 seconds; I have even induced it with a DL dongle. Repeats the same. Recovery mode is a no go-phone flashes sammy logo and goes silent. You are right the first issue to fix is the power button. I will update this weekend once I take it apart. Thanx all the same.
Related
Hi everyone
My SGS 2 won't start anymore
I charged my phone, then went somewhere, used the phone, put it back in my pocket and the next time i looked at it it was shut down and i couldn't turn it on anymore, nothing happens at all.
theres no problem with the battery (it works on another SGS 2)
I rooted my phone and put lightning rom 1.2 on it. i had no problem rooting the phone and its the first rom since stockrom.
What should I do?
So you mean your phone won't boot anymore? There is no Samsung logo or anything?
Sent from my GT-I9100 using XDA App
no logo, no vibration, just black
tried normal startup as well as "vol down, home, power"
Recovery vol up + home + pwr release at splash screen .
You can either try the usb recovery jig though this poster says it does not work but in my view worth a try.
http://forum.xda-developers.com/showthread.php?t=1206967
Or take your chance and return the phone under warranty .
jje
Did you try removing battery, replacing and then turning on. I had the same issue yesterday and this worked for me.
Sent from my GT-I9100 using XDA Premium App
Samsung GS2 - System Crashed black screen
+1 Here. I got the same thing
I’m really newbie, first time play on Android phone and got crash
However, below are what I did in chronological order
1) I did and success
http://www.inspiredgeek.com/2011/04...ng-odin-and-superoneclick-step-by-step-guide/
2) Did & Success
http://forum.xda-developers.com/showthread.php?t=1154252
3) Did & fail
http://forum.xda-developers.com/showthread.php?t=892297
4) Outcome
It restarted, and keep restarting at Samsung start-up flash screen repeatly, can not load into mobile home screen.
I bought to Malaysia Samsung Service Center. They mention can try to flash my phone but not guaranteed. Worst still, Result:- black out, can’t start the phone even pressing power button.
Thanks, appreciate that
ps: I bought from Bangkok, is Malaysia version different? Btw, I did try to do the hard reset but same. (Vol Up + Home + Power button, then Wipe Data/ Factory Reset)
I screen capture baseband version is DXKF1, Build number is Gingerbread.DXKF4
Thanks alot man. Truly appreciate if any alternative solution or suggestion?
Having the exact same problem,
Charged phone
Listened to some music for 30 minutes
put the phone away on the table
Two hours later I noticed the phone had shut down.
Trying to boot it nothing.
Nothing when put in wall socket charger.
Nothing when connected to USB.
Vol Up + Home + Power button does nothing.
running Lightning rom 1.2 or 1.3
Phone is 2.5months old.
You may have your last try - USB jig
Same problem here, shut down the phone to put a new microsd and when i try to start it only a black screen, no samsung logo, no vibrate, no nothing....
I try to remove sim and microsd and no result, changed battery, no result, battery works in another SGS2....
Any solution?
EDIT: WORKS AGIAN!!!! i leave it alone without battery around 30 mins then put battery and working again...
my phone won't turn on. I set it down around 26% battery and went to check it about 30 min later. BLACK. plugged it in. battery break still nothing... no vibrate no lights nothing!
im leaving battery out for the night and will try it back in in the morning but im doubtful! my life sucks.
tylerlaczko said:
my phone won't turn on. I set it down around 26% battery and went to check it about 30 min later. BLACK. plugged it in. battery break still nothing... no vibrate no lights nothing!
im leaving battery out for the night and will try it back in in the morning but im doubtful! my life sucks.
Click to expand...
Click to collapse
Tried many things and not working. Sending it in for warranty. At least they wont know its hacked until they fix it. Maybe they wont charge me...
tylerlaczko said:
Tried many things and not working. Sending it in for warranty. At least they wont know its hacked until they fix it. Maybe they wont charge me...
Click to expand...
Click to collapse
So what happened? Did they work out that it was hacked and were you charged?
Hi guys,
Very confused here!
I was running the latest AOKP Hydrogen rom and one of the latest Siyah kernels...
I recently moved onto the S3, so I was basically prepping my S2 to be sold. What happened was as follows:
I had my S2 connected to my PC to get some data off of it;
I went into the factory reset menu and it froze so I unplugged the USB cable (I assume it was waiting for the SD card to become available.
It displays the "settings is not responding. Would you like to close?" message, but I clicked wait and it seemed to work fine as I'd disconnected the USB cable;
At this point the battery was at about 19%;
I clicked factory reset with wipe SD card;
After a few minutes I check the phone and it's completely blank. I figure it's doing something and can't turn the screen on so I leave it for a few more minutes;
Eventually I grow concerned and assume the phone has crashed, so I hold down the power button to do a hard reset.
After this the phone does not turn on.
It does the following:
If I try to turn it on it displays the SGS2 logo (with the yellow triangle) for a few seconds and then turns off.
If I connect it to the power it displays the loading screen of the battery charge app for a few seconds and then turns off.
Sometimes if I mash the buttons it will flash on and off with a pure white screen until I hold the power button and turn it off.
Any ideas, guys?
My only idea is that something crazy has happened with the battery as I did swap my extended battery with my girlfriend's normal battery last night. As I work in a phone shop, I'll charge up the battery in another phone to make sure it has power.
But I know the battery has power, and the phone it doing exactly the same thing with my old 1650mah battery (which may or may not have power in it).
Any ideas? I was going to be selling it for around £200, so it was gonna really take the load of my shiny, new S3! 0_o
SirCanealot said:
Hi guys,
Very confused here!
I was running the latest AOKP Hydrogen rom and one of the latest Siyah kernels...
I recently moved onto the S3, so I was basically prepping my S2 to be sold. What happened was as follows:
I had my S2 connected to my PC to get some data off of it;
I went into the factory reset menu and it froze so I unplugged the USB cable (I assume it was waiting for the SD card to become available.
It displays the "settings is not responding. Would you like to close?" message, but I clicked wait and it seemed to work fine as I'd disconnected the USB cable;
At this point the battery was at about 19%;
I clicked factory reset with wipe SD card;
After a few minutes I check the phone and it's completely blank. I figure it's doing something and can't turn the screen on so I leave it for a few more minutes;
Eventually I grow concerned and assume the phone has crashed, so I hold down the power button to do a hard reset.
After this the phone does not turn on.
It does the following:
If I try to turn it on it displays the SGS2 logo (with the yellow triangle) for a few seconds and then turns off.
If I connect it to the power it displays the loading screen of the battery charge app for a few seconds and then turns off.
Sometimes if I mash the buttons it will flash on and off with a pure white screen until I hold the power button and turn it off.
Any ideas, guys?
My only idea is that something crazy has happened with the battery as I did swap my extended battery with my girlfriend's normal battery last night. As I work in a phone shop, I'll charge up the battery in another phone to make sure it has power.
But I know the battery has power, and the phone it doing exactly the same thing with my old 1650mah battery (which may or may not have power in it).
Any ideas? I was going to be selling it for around £200, so it was gonna really take the load of my shiny, new S3! 0_o
Click to expand...
Click to collapse
If it was bricked it wouldnt turn on even a bit. Just charge it or try changing the battery.
coolstorybro_123 said:
If it was bricked it wouldnt turn on even a bit. Just charge it or try changing the battery.
Click to expand...
Click to collapse
If I try to charge it it displays the SGS2 charging screen for a few seconds and then switcher straight off.
I just got into work and tried my colleagues 2000mah battery which had 32% in it. Exactly the same problem. WTF????
Thanks
Edit: FYI, it turns off before entering download mode or recovery. WTF????
Maybe you hit this ?
VAXXi said:
Maybe you hit this ?
Click to expand...
Click to collapse
That's just what I was thinking, actually
I couldn't find a description of what actually happens when this brick happens. The page doesn't really say... Does anywhere say?
Edit: I swear I didn't even flash the Siyah RC6 that was known to brick the phones either... -_-;;
Thanks!
It's not just a specific kernel, more are actually faulty. The whole story is here.
SirCanealot said:
Hi guys,
Very confused here!
I was running the latest AOKP Hydrogen rom and one of the latest Siyah kernels...
I recently moved onto the S3, so I was basically prepping my S2 to be sold. What happened was as follows:
I had my S2 connected to my PC to get some data off of it;
I went into the factory reset menu and it froze so I unplugged the USB cable (I assume it was waiting for the SD card to become available.
It displays the "settings is not responding. Would you like to close?" message, but I clicked wait and it seemed to work fine as I'd disconnected the USB cable;
At this point the battery was at about 19%;
I clicked factory reset with wipe SD card;
After a few minutes I check the phone and it's completely blank. I figure it's doing something and can't turn the screen on so I leave it for a few more minutes;
Eventually I grow concerned and assume the phone has crashed, so I hold down the power button to do a hard reset.
After this the phone does not turn on.
It does the following:
If I try to turn it on it displays the SGS2 logo (with the yellow triangle) for a few seconds and then turns off.
If I connect it to the power it displays the loading screen of the battery charge app for a few seconds and then turns off.
Sometimes if I mash the buttons it will flash on and off with a pure white screen until I hold the power button and turn it off.
Any ideas, guys?
My only idea is that something crazy has happened with the battery as I did swap my extended battery with my girlfriend's normal battery last night. As I work in a phone shop, I'll charge up the battery in another phone to make sure it has power.
But I know the battery has power, and the phone it doing exactly the same thing with my old 1650mah battery (which may or may not have power in it).
Any ideas? I was going to be selling it for around £200, so it was gonna really take the load of my shiny, new S3! 0_o
Click to expand...
Click to collapse
your phone is ok as far as it shows u the s2 logo
you have 2 things to do , try to go to recovery or download mode and formate data/factory reset then flash another rom , btw what kernel u used before your phone go to this situation ? if you were using stable kernel "cm,neak,fluxi,syah stable" so you are safe from hardbrick bug , and the hard brick bug is done only if you have faulty kernel and wibed your data through recovery , and this isn't your situation , so don't be afraid
evaworld said:
your phone is ok as far as it shows u the s2 logo
you have 2 things to do , try to go to recovery or download mode and formate data/factory reset then flash another rom , btw what kernel u used before your phone go to this situation ? if you were using stable kernel "cm,neak,fluxi,syah stable" so you are safe from hardbrick bug , and the hard brick bug is done only if you have faulty kernel and wibed your data through recovery , and this isn't your situation , so don't be afraid
Click to expand...
Click to collapse
Thanks for saying, but I can't get into recovery or download. The phone switches off before then!
That's what's so confusing! xD
Thanks
With a known good batter try hard resetting to download mode 2x in a row.. Hold the button config to get into download mode.. Hold it through two restarts.. Might work.
Sent from my GT-I9100 using xda premium
I've nuked mine a few times with buggy kernels, sounds like a similar situation. I got my device back by flashing CM9 resurrection, then flashing Siyah, and finally from CWM flashing an ICS-based stock ROM.
I'd suggest taking a backup of your efs unless you're selling it with stock.
Sent from my GT-I9100 using XDA
SirCanealot said:
Hi guys,
Very confused here!
I was running the latest AOKP Hydrogen rom and one of the latest Siyah kernels...
I recently moved onto the S3, so I was basically prepping my S2 to be sold. What happened was as follows:
I had my S2 connected to my PC to get some data off of it;
I went into the factory reset menu and it froze so I unplugged the USB cable (I assume it was waiting for the SD card to become available.
It displays the "settings is not responding. Would you like to close?" message, but I clicked wait and it seemed to work fine as I'd disconnected the USB cable;
At this point the battery was at about 19%;
I clicked factory reset with wipe SD card;
After a few minutes I check the phone and it's completely blank. I figure it's doing something and can't turn the screen on so I leave it for a few more minutes;
Eventually I grow concerned and assume the phone has crashed, so I hold down the power button to do a hard reset.
After this the phone does not turn on.
It does the following:
If I try to turn it on it displays the SGS2 logo (with the yellow triangle) for a few seconds and then turns off.
If I connect it to the power it displays the loading screen of the battery charge app for a few seconds and then turns off.
Sometimes if I mash the buttons it will flash on and off with a pure white screen until I hold the power button and turn it off.
Any ideas, guys?
My only idea is that something crazy has happened with the battery as I did swap my extended battery with my girlfriend's normal battery last night. As I work in a phone shop, I'll charge up the battery in another phone to make sure it has power.
But I know the battery has power, and the phone it doing exactly the same thing with my old 1650mah battery (which may or may not have power in it).
Any ideas? I was going to be selling it for around £200, so it was gonna really take the load of my shiny, new S3! 0_o
Click to expand...
Click to collapse
i am having exactly the same problem.i did a factory reset after flashing siyah kernel (SiyahKernel v3.3.1) on Resurrection remix v2.2.let me know if you guys find any solutions
JIG
try to use a download mode JIG.
I'm not sure if a link will violate xda-rules....
google it
dont worry
if you boot up and are getting the sg2 logo then you have not bricked you phone.
to fix simply download a .tar version of any rom and run odin to pda reinstall if you wanted to you could go the whole hog and reflash a fresh cf-kernal (rooted or stock) and then flash fresh firmware. just remember to get the kernal that originally matches the (ithink) your correct baseband ie xxki4
there should be no worries aslong as you dont pull the plug.
could have had a worse error saying installation incomplete please use kies then you would have to had taken battry out reinserted and hoped the three butn combo for rec. mode worked happened to me awhile back lol
hope i helped you
ps never read your post fully just skimmd the jist of it although the above should be applicable
also try resetting your battry stats in cwm
finally fixed
thanks for the help everyone.i have fixed it now.it seems like the problem was with the updated version of siyah kernel .i managed to put the phone in download mode.(kept the phone on the charger for a while. than, i don't know some how when i tried to go to download mode it did).and flashed siyah kanel v3.2.6.4 via odin
My Samsung Stratosphere turned itself off sometime and now is rebooting to the Samsung logo, and then turning back off, and rebooting (a couple times earlier it booted to the main android menu, but turned back off immediately afterwards) and when I plugged it into the charger it acts like it's charging and then turns off and acts like it's charging and over and over again, even when the battery indicates that it's at more than half full.
Does anyone know what's happening? (no custom ROMs or anything, it's all standard btw). I took the battery out and everything and it still does the same thing when I put it back. I tried to do a factory reset, but the recovery mode screen always jumps away when I try to activate it (I press both Vol+ and Vol-, recovery mode screen comes up but goes instantly, then the phone goes into a boot loop again).
Please help, thank you!
Bump!
Bump please!
Bump!
Please help, thanks!
Hi, I'd recommend sending the phone into warranty, add the phone isn't rooted, you can't do much.
Sent from my HTC One S using Tapatalk 2
Had same problem on 3 phones. This is a connection problem within the phone. Disassembly & cleaning contacts often helps for a while, but problem comes back. Bumping the phone on the side or top, often allows it to work properly, for a short while, and so does squeezing it, in certain places. Get a new one, since the problem will re-cur.
I have an s3 that has been rooted running a custom rom perfectly for about 5 months.
Today I was using my phone and it locked up - totally froze..screen was frozen and everything was unresponsive. So I pulled the battery.
When I put the battery back in my phone displayed the Samsung logo and after that just displays a black screen.
I can put the phone in download mode, however it will only be on the download screen for about 3 seconds before the phone either turns off or the screen goes black.
The really weird thing is, when I put the battery into my phone it will instantly boot up (I don't have to hold download the power button). The power button is NOT stuck in the down position.
I know the battery is charged. So what in the hell happened? I don't know if my phone is bricked or not. I could re-flash it but I can't do anything in download mode because of it turning off.
Any help would be appreciated. Thanks.
irodex said:
I have an s3 that has been rooted running a custom rom perfectly for about 5 months.
Today I was using my phone and it locked up - totally froze..screen was frozen and everything was unresponsive. So I pulled the battery.
When I put the battery back in my phone displayed the Samsung logo and after that just displays a black screen.
I can put the phone in download mode, however it will only be on the download screen for about 3 seconds before the phone either turns off or the screen goes black.
The really weird thing is, when I put the battery into my phone it will instantly boot up (I don't have to hold download the power button). The power button is NOT stuck in the down position.
I know the battery is charged. So what in the hell happened? I don't know if my phone is bricked or not. I could re-flash it but I can't do anything in download mode because of it turning off.
Any help would be appreciated. Thanks.
Click to expand...
Click to collapse
what about recovery mode? does that work?
the power button can be shorted even though the button is not pressed
Sounds like SDS send it for repair.
KayKrate said:
Sounds like SDS send it for repair.
Click to expand...
Click to collapse
no, it really doesn't
lefttobleed said:
what about recovery mode? does that work?
Click to expand...
Click to collapse
When it tries to enter recovery mode I get the black screen as well
take out the battery. insert it after atleast 5 minutes. i've read somewhere that S3 is sensitive to the order of the keys we hold to enter download or recovery modes. so to enter download mode, 1st hold HOME button, then VOLUME DOWN button and then the POWER button. (not sure i did this all the time but no problem for me till now). good luck
SRIRAM
Sent from GALAXY S3 I9300 running PARANOID ANDROID 3+
Today while getting lunch my GS4 shut off and wouldn't turn back on. I am running Hyperdrive RLS18.1, and it has been working fine up until today. I have tried everything to get it to boot past the samsung custom logo. The steps I take to get it to the logo are- 1) Take out the battery 2) Put battery back in 3) Screen boots up with samsung logo(if it is plugged into the charger it shows the charging battery then goes to black) 4)the screen turns off. I have tried putting it into download mode by holding the home-power button-volume button combo, but it won't boot into download mode. I tried plugging it into the computer and it doesnt recognize it because it is off. I have two different batteries that I tried to put in the back, but they both do the same thing. Does anyone have any suggestions on how to go about fixing this? And if I go into the verizon store and my phone gives the samsung logo with custom underneath it will they uphold the warranty? I doubt since rooting voids it....Thanks for any help in advance!
After trying some more options to fix the phone, I was able to get it into download mode, but then the screen turned off again. I realize that the problem is the screen won't stay on for more than a second or two. No matter what comes up, the screen turns off. But when plugged into the computer, it also just shuts down.
can you get into safestrap?
bamige1 said:
can you get into safestrap?
Click to expand...
Click to collapse
I actually had this phone before the bootloader was locked, I think. I never had to use it to root.
I have no idea why this worked, but after letting my phone sit all night, I tried this video -https://www.youtube.com/watch?annotation_id=annotation_1286109531&feature=iv&src_vid=SSLZFmhmBlc&v=uc0afHKahR4 . I have no idea why it worked, but it did. So if anyone comes upon this thread and has this problem, feel free to contact me and I will try to help you fix the problem.