[Q] Battery doesn't charge - HTC Droid DNA

Hi, I had no issues with battery or battery life but all of a sudden the battery stopped charging even with the original OEM charger. Even if I put the charger for hours, it only goes till 2%. When its off, the charge led blinks for 20-30 mins after which I can switch it on. I suspect if it has anything to do with a screen protector installation that I did. I applied the protector after moistening it with this liquid spray provided with the zagg protector. I've seen the battery issues a day after that. Does it have anything to do with moisture forming inside the phone which is causing issues charging my battery?
Kindly share your thoughts and experiences on how it can be recovered and if battery replacement would be a solution. Adding to above, I can see no other issues which are seen when water goes into the phone.

Any suggestions please? It's been 3 days for me without a phone

This may be a stupid question, but, knowing you've tried different chargers, have you tried a different cable? I know mine's really worn down, and will lose connection easily if I push down on the plug attached to the phone. If you can, see if it behaves any differently on a Qi wireless charger.

Related

[Q] Phone Charging While Unplugged (vbus_present)

Hey guys!
I have a weird issue with my phone, and after doing a bit of research I got a bit pessimistic, so here it is:
When I unplug my phone from the charger, the phone stays in "charging" state, which means the charging icon is there, the battery stats are not shown correctly, I can't plug it into my PC via USB, etc. It also doesn't enter deep sleep, since there is a vbus_present wakelock held, which is normal for charging.
I've read that water damage can be one of the causes, and if I think of it, I did have my phone with me, while I took a long bath. While the phone didn't touch any water, the air humidity was really high , so I could blame this for the issue.
Do you have any suggestions / ideas?
Thanks!
Hello?
My phone is dying here!
Sounds like water damage to me... however sometimes, to my knowledge, the issue can be solved like the fuel_alerted wakelocks: pull battery for a while and reinsert. But I assume you already tried that, so water damage would be my best guess although air humidity shouldn't cause that...
It is the same for me when I dropped my phone into water. However, it is now normal again ( lucky me). For your case, I think it water damaged, I would suggest you dry your phone. Take out the battery, dont use phone for some hour(4-5hrs in my case), dry the phone by whatever you can( I just put in under the sun for 15mins, and put it in a bag of rice). It was 2 days since I got the problem, but now its ok. Just try it.
Hope it helps
P/s: still get some minor problem but I can bear with it though
Fixed ?
Hi,
It seams a bit too laste to answer, but it might help someone esle.
I had quite the same issue, and it seams that the solution is to clean the phone USB slot with a toothbrush...
cant post the reference url cause i'm new... so search for "galaxy s2 won't turned off"...
VBUS present wakelock caused by using Apple compatible charger
It does not look like this was ever resolved, so figured I would chime in since I have been looking at this for a while.
If you use a charger which is compatible with Apple products, it will cause the vbus_present wakelock since Apple does not adhere to USB standards and requires two of the pins to be bridged or open (can't remember which) to work for their products. However, when you charge a device that does adhere to USB standards with one of these chargers, it will cause the wakelock (on all the samsung phones I have seen, anyway).
Another downside to using an apple compatible charger is that you can never get more than 500ma out of it due to the non-standard USB connection, even if the charger is capable of 2000ma output. So you get slower charging.
When you are connected to any charger, this wakelock will be present. If you use an Apple compatible charger, it will persist after you unplug it and will drain your battery around 10% per hour since it prevents it from going into deep sleep. You can clear the wakelock by rebooting the phone or plugging it into a standard USB charger, such as a PC or Samsung charger, even for a few seconds.
You can use Better Battery Stats to see the effects of this wakelock. Note that it can take a few minutes to show up once you have unplugged from the apple charger.
Yes, this really p*sses me off. This is one of the reasons I no longer have any Apple products in my house and long since thrown away all the Apple compatible wall chargers I once had. It still comes back to bite me since I still have a couple of chargers that contain batteries to charge when you are away from a wall outlet and they both cause this. When I use them I just have to make sure I reboot afterward. The USB outlet I have installed behind the stereo in my car also causes this wakelock. I have one to replace it but have not gotten around to removing the stereo to do this yet.
The next best solution to never using an apple compatible charger at this point would be to have a kernel that addresses this and removes the wakelock after it is unplugged but I don't see this happening.
Man, I know you love your S II, but don't go taking a bath with it!
Was this recent? why don't you give the little guy a rest and leave it a day in rice, stucked inside a zip lock bag, can't hurt.
Googled this "vbus_present android battery not plugged in"
found this thread. Seems to have worked for me by simply rebooting. thx!

Gtab won't charge

:crying: So this is the first time in a while I have posted here. But annoyingly enough my Gtab (for the second time) has not been taking charge. It will turn on when plugged it (but no red light) so I assume its the battery that won't take a charge. The last time this happened I formatted it, then nvflashed it, and let it sit for 24 hrs before charging. I will try that again but any help or input is appreciated
One of my Gtabs doesn't charge very well either. The charging pin is messed up and will only charge when I plug it in and prop it in a certain way. Sometimes the red light turns off, sometimes it stays on but still doesn't charge. Eventually I will have to re-solder the connection, but have been putting it off. If you cannot fix it by other means (try a different charging cable? reflash as you suggested?) here is a good set of instructions on how to do this.
Gtab Charging Pin Repair
Good luck and I hope it doesn't come to this. You could also buy a charging dock if you don't want to tear apart and solder your tablet. Also, here is some info on battery replacement if that turns out to be your problem.
Info on Gtab Battery
Gtab Battery Ebay (not advertising, just trying to help)
+1 to DaggerDave's suggestion.
From my research the Gtabs power plug is very VERY flimsy. I've had to solder mine back on (and a hefty amounts of glue) and now it works fine, though I treat it very delicately. The dock is going at around $50 on fleabay (search malata/gtab dock)
YAY
DaggerDave said:
One of my Gtabs doesn't charge very well either. The charging pin is messed up and will only charge when I plug it in and prop it in a certain way. Sometimes the red light turns off, sometimes it stays on but still doesn't charge. Eventually I will have to re-solder the connection, but have been putting it off. If you cannot fix it by other means (try a different charging cable? reflash as you suggested?) here is a good set of instructions on how to do this.
Gtab Charging Pin Repair
Good luck and I hope it doesn't come to this. You could also buy a charging dock if you don't want to tear apart and solder your tablet. Also, here is some info on battery replacement if that turns out to be your problem.
Info on Gtab Battery
Gtab Battery Ebay (not advertising, just trying to help)
Click to expand...
Click to collapse
tthats really good information thanks! :laugh:
but i did get it to work. I opened up my tablet and checked to make sure the battery was plugged in its socket thing. Guess what. it wasnt.
It probably became loose when i had to open it up to fix my screen. So all i did was reattach it and put a small piece of electrical tape over it, just in case.
:laugh:

[Q] Droid Razr Maxx Screen Fixed, But Wont charge Past 5%

Hello all!
I recently purchased a used Droid Razr Maxx from a co-worker. The lcd screen was cracked so I replaced it. I took apart the phone completely and reassembled it with the new screen in place. The phone turns on just fine, the Motorola icon shows up and it gets to the charging battery icon with 5%, but after a few hours of letting it charge, it stays at 5% and wont turn on. Keep in mind, the phone has been charging for two hours from the time this post was made.
My question is, did I somehow damage the battery when operating internally? I can replace the battery if needed.
Another question. If I damaged the motherboard, would the phone turn on at all?
I am kind of wondering if there is a certain thing I needed to do before plugging it in.
To answer any questions that might be asked: The battery was completely dead when I did repair the screen. The charger is a wall usb charger, not plugged into my computer. I did place all the components inside the phone, to the best of my knowledge. I have had experiences when it comes to internal repair.
check for how long this 5% charge remain. it usually happen due to problematic battery guage
faheemakbar18 said:
check for how long this 5% charge remain. it usually happen due to problematic battery guage
Click to expand...
Click to collapse
Morning now. The battery is still at 5%. The phone shuts off soon as the charger is not connected. Does not seem to hold a charge. Think I should buy a new one?
Garret27 said:
Hello all!
I recently purchased a used Droid Razr Maxx from a co-worker. The lcd screen was cracked so I replaced it. I took apart the phone completely and reassembled it with the new screen in place. The phone turns on just fine, the Motorola icon shows up and it gets to the charging battery icon with 5%, but after a few hours of letting it charge, it stays at 5% and wont turn on. Keep in mind, the phone has been charging for two hours from the time this post was made.
My question is, did I somehow damage the battery when operating internally? I can replace the battery if needed.
Another question. If I damaged the motherboard, would the phone turn on at all?
I am kind of wondering if there is a certain thing I needed to do before plugging it in.
To answer any questions that might be asked: The battery was completely dead when I did repair the screen. The charger is a wall usb charger, not plugged into my computer. I did place all the components inside the phone, to the best of my knowledge. I have had experiences when it comes to internal repair.
Click to expand...
Click to collapse
It could be a faulty charger.
Normally, If the battery is poor, it won't hold charge but it won't stick to a particular percentage. It will only discharge sooner. But given the fact you got the phone dead, it might as well be the battery.
Worst scenario, you damaged the charging port.
I'd begin with using a different charger, if that doesn't work, try another battery.
neo.ank said:
It could be a faulty charger.
Normally, If the battery is poor, it won't hold charge but it won't stick to a particular percentage. It will only discharge sooner. But given the fact you got the phone dead, it might as well be the battery.
Worst scenario, you damaged the charging port.
I'd begin with using a different charger, if that doesn't work, try another battery.
Click to expand...
Click to collapse
I have used other chargers and they all work for my other phones, just not this one. I am hoping it's a dead battery and not something to do with the motherboard. My friend wont let me dismantle his phone to see if it's the batter, lol.
Just the clarify, the phone doesn't boot up completely, only to the charging screen. The battery icon with 5% shown. When I unplug the phone from the charging screen, it just dies. Will not even boot up to the phone animation.
I purchased a battery replacement off of Ebay. It'll arrive in a few days. Let's hope this works!
Still could be the charger. Did you check voltage and amp specs? 850amps 5.1v
This phone can be picky. First razr I got had broken screen, repaired it and found myself in the same situation.
Connecting to a laptop would not charge it. Only stock charger. IPhone charger or chargers designed for iphones will not work.
Edit: When replacing battery, position is critical. If battery terminals are a little bit displaced it will not turn on.
Displacement can be minimal or imperceptible but will cause troubles. If possible don't place cover before checking that it turns on. (please avoid touching circuits or battery terminals or will get worse).
Sent from my XT910 using xda app-developers app
angrist said:
Still could be the charger. Did you check voltage and amp specs? 850amps 5.1v
This phone can be picky. First razr I got had broken screen, repaired it and found myself in the same situation.
Connecting to a laptop would not charge it. Only stock charger. IPhone charger or chargers designed for iphones will not work.
Edit: When replacing battery, position is critical. If battery terminals are a little bit displaced it will not turn on.
Displacement can be minimal or imperceptible but will cause troubles. If possible don't place cover before checking that it turns on. (please avoid touching circuits or battery terminals or will get worse).
Sent from my XT910 using xda app-developers app
Click to expand...
Click to collapse
That was exactly the problem....
I got the new battery, but not 24 hours later, I was realigning the cables inside it (like the front facing and rear cameras, along with the WiFi antenna) I slightly moved the replaced battery and the cable to the battery to the motherboard tore itself. After a long face-palm moment, I got the old battery back in place and realigned it very carefully. It turns out it still works, but I am out a new battery.
Apart from the battery, I need to find out why the front speaker won't work. Either the speaker is damaged or something needs to be in place correctly, besides the cable. Also need to get some adhesive gel to bond the screen and case together.
Damn I really had forgotten about that speaker. The fact is it tends to break. It has very fine copper wire winding that can break when you remove it the wrong way.
Having no experience I pulled not knowing that speaker is glued to motherboard. At that time I didn't knew it and thought that little bar left was part of the motherboard.
Since you disassembled almost everything, that must be the reason it is failing. If it is not that, it is badly plugged but I really doubt it.
Alas Never fixed it, so i can't tell correct process to reassemble or disassemble that speaker. Instead I searched for apps that would activate loud speaker automatically during calls.
Would have been nice to fix it but I got the opportunity to acquire a RAZR maxx so never touched and sold instead.
Removing that glue might involve using a hot air gun. So that you don't damage motherboard removing by force. (But again too much heat could Fry motherboard)
Maybe someone could share it's experience?
About that screen, Remember to have read about a 3m adhesive spray in some thread.
Also some one just passed hot air that melted original glue but it would be better not to play with heat over a battery.
Sent from my XT910 using xda app-developers app

[Q] Will not boot, flickers quickly

Hello. My wife recently dropped her S2, with enough force to eject the battery. It had worked after she put it back in and all, and even called me to tell me about it. However, the battery ended up dying before she plugged in it. When plugging the phone into usb, the button lights would flicker and the battery charging icon would flash on for about a second. Rinse and repeat. If there is no battery in the phone, it just flickers the buttons, and the screen will flicker back, and just do it over and over.
The USB port on it was already really shoddy, so I bought a new ribbon and replaced it. Same symptoms. Pretty sure this is a hardware problem, although what the problem is exactly I do not know. I've already reseated all of the ribbon connections I could find. There's obvious signs of previous water damage, but it looks like very old damage. I wouldnt' be surprised if something is corroded, but the timing of this happening after it was dropped makes me think something else came loose. I just don't know what. I could potentially try to reflow the motherboard with my heat gun, but before I waste my time doing that, I was wondering if there's _anything_ else that could be causing these symptoms.
Thank you.
Over the 2-1/2+ years I have been reading this forum, I have seen a number of cases reported where the battery discharges fully and then will not recharge in the phone, while the phone exhibits symptoms similar to the ones you report. As far as I can remember, in every case the phone would boot up when a fully charged battery was inserted. And once the battery was charged, phone would then recharge the battery as long as it was not completely discharged. Not all phones behave this way. For instance, I have fully discharged my phone on several occasions without issue.
Therefore, I would first try inserting a fully charged battery to see if the phone boots up ok, and see if it will charge with a partially charged battery. Some have had to buy an external charger just for this purpose, or borrow a charged battery from another phone, etc.
creepyncrawly said:
Over the 2-1/2+ years I have been reading this forum, I have seen a number of cases reported where the battery discharges fully and then will not recharge in the phone, while the phone exhibits symptoms similar to the ones you report. As far as I can remember, in every case the phone would boot up when a fully charged battery was inserted. And once the battery was charged, phone would then recharge the battery as long as it was not completely discharged. Not all phones behave this way. For instance, I have fully discharged my phone on several occasions without issue.
Therefore, I would first try inserting a fully charged battery to see if the phone boots up ok, and see if it will charge with a partially charged battery. Some have had to buy an external charger just for this purpose, or borrow a charged battery from another phone, etc.
Click to expand...
Click to collapse
Thanks for the detailed reply. I will try to find a battery. I do have a question though. If the battery was the cause of this, should the phone not act like this if the battery was not inserted? I would expect it to boot up just fine with the wall charger plugged into it without the battery in it, but that does the same thing (minus the battery icon).
Thank you.
I'm just not sure the answer to that. I can't remember if anyone mentioned that, although as I think about it, it seems like someone mentioned that as well. Still, I think this should be the first step in trouble shooting, because if this is the issue, and the phone is otherwise fine, then you don't want to be using a heat gun on it, or any other more difficult steps until you have eliminated this possibility.
Also, you might consider sending the phone out for repair if this step does not solve the issue. Assuming you are in the USA, Mobile Tech Videos is a very reputable shop that can deal with many issues.
You may be correct on this. The battery won't even charge through the external charger (my atrix battery charges fine on it so the charger is good). New battery (even though this is new) it is.
Update: The pins on the battery were labeled wrong. The label wasn't placed in teh correct position. I looked up a pic of another battery and found the label was offset by 1 pin, so I offset the charging pins by 1 and bam, it started charging. 50% charge, popped in the battery, and boom, booted right up.
Thanks creepycrawler!

[Q] Truesmart not charging!

OK. I know this has been discussed many times before, but I can't seem to find an answer. I have tested the cradle extensively with digital testers and probes, the problem is not with the cradle nor is it with the contacts on the back plate of the watch itself. The watch just randomly refuses to charge no matter what the voltage of the battery is. The only way I can get it to start charging again is to pull the battery for a few minutes. the only thing I can think of at this point is it's some kind of software bug. it's happening more and more frequently, the battery is currently at 97% and it stopped charging again, popped the battery for a few minutes put it back together and bam! ... charging again! This is so frustrating anyone else had this specific problem? and again let me reiterate, it is not an issue with the cradle or the back plate of the watch.

Categories

Resources