My son got the above mentioned for his Christmas and has only gone and put a pin on it to forget the pin and now we can't get into anything, any instruction welcome.
Hello what device is that your son forgotten the password??
Its for a Asus transformer pad tf103c
If you are unable to power off , try this process from point 2.
1. Unplug the power cord and shut the unit off .
2. Press and hold the VOL DOWN and then POWER button at the same time for at least 10- 12
seconds until after the start - up screen appears and is joined by some small print at the top of
the screen, then let them both go . If the TF booted the way it always does , you have not
accomplished the task , try again until you have seen 2 icons ( ICS), 4 icons ( JB ) in the screen.
3. After a few seconds you should see some icons in the middle of the screen - in ICS they are
called "Wipe Data" and " Android" . The right " Android" will have a green highlight fading in and
out. In JB there are four, the first of which is RCK .
4. Press the VOL DOWN button to select the " Wipe Data" icon then VOL UP to confirm it .
Thanks, these are the same instruction as Asus gave but when doing so the start up Asus screen shows then goes black and nothing when I let the buttons go and press only the power button it quickly goes white and switches off, any ideas?
Hello so may you show me pictures to see the problem with your tablet.
Send from my RCA TAB 7" RCT6378W2
Related
Hi All,
I just got a Tab yester and I noticed a couple of this which am not sure if its normal to the tab or not.
1. When I press and hold the power button I was expecting a dialogue box with options to switch off or restart etc but it just shutdown the Tab as against the rooting video available on here where the guy pressed and held the power button to get a couple of option, not sure if this is a fault with my tablet or not.
2. when I turn off the screen and switch it back on I was expecting a lockscreen that I can just drag to unlock but i do not seem to get that, I ve been to security and the only options are pattern, PIN and password, but i was just looking for a drag to unlock screen option which is not available.
Please advise.
Thanks in advance.
I have the same problem
I have a problem with my truesmart I have a keyboard that stays on permanently , I cannot get rid of it it comes up across the clock like it wantsme to type something in the box , I cannot get into anything else on the watch , I have tried taking the battery out but it still comes back it just wont go and I cant use the watch"
Pull the battery
Put battery in
Hold down both buttons (this gets you to recovery)
If you see no menu on the screen, hit the power button
In the menu use the back button to scroll down to factory reset
Hit the power button to select
You will loose what ever apps and data you put on the watch but this should fix it. If not your options are to either flash a ROM or send it back to Omate.
I have a Blu Touchbook Pro 7, recently when trying to unlock it, the keyboard would not pop-up to type the password. After re-starting, and shutting the tablet down, the problem still remains. I tried looking for a hard reset option but I don't see any little hole I can insert a clip in.
So, when I tap the touchscreen the keyboard does not appear. For all other options the touchscreen works perfectly.
Does anyone know how to solve this problem???
HedilinaV said:
I have a Blu Touchbook Pro 7, recently when trying to unlock it, the keyboard would not pop-up to type the password. After re-starting, and shutting the tablet down, the problem still remains. I tried looking for a hard reset option but I don't see any little hole I can insert a clip in.
So, when I tap the touchscreen the keyboard does not appear. For all other options the touchscreen works perfectly.
Does anyone know how to solve this problem???
Click to expand...
Click to collapse
You don't need to go poking around in holes. Just hold down the Vol+ and the Power button. A little menu pops up. select "recovery mode" with volume down key, then run it by pressing volume down...and you will be in recovery. From there, select "wipe data/factory reset" and you will be able to reboot normally without the screen code (it is wiped as well as all of your data!)
I have installed the newest Malaysk ROM on my HU. On the picture attached you can see the Advanced Power Menu like it should be. In my case there is only Reboot after long pressing the button on the top right. Does it belong to the launcher? If I am pressing the button only short my device turns black, but the knobs are still lightning (also you can hear the radio). It seems that the device is hanging up so I had to press the reset button.
Also I want to know If its possible to shutdown the unit completely. Without having connected the ACC wire.
I have the same question about the pwer menu. Like you I only get one option.
How to enter Recovery mode in intex Irist, please please please help me some one.
Probably it's too late to reply but it may help somebody else so here it goes...
Turn off your watch phone. Wait till it's completely off and some more time. Then, press the bottom button and top button simultaneously until you land on the recovery screen. Basically you can first press the bottom button, keep it pressed and then power the watch phone with the top button, as you normally do, while the bottom button is pressed.
In the recovery mode, as far as I remember, the bottom button is used to scroll the cursor down and top button is used to select. Cursor goes back to the top when the end of the list is reached and then comes down in cycle.
Addy11 said:
Probably it's too late to reply but it may help somebody else so here it goes...
Turn off your watch phone. Wait till it's completely off and some more time. Then, press the bottom button and top button simultaneously until you land on the recovery screen. Basically you can first press the bottom button, keep it pressed and then power the watch phone with the top button, as you normally do, while the bottom button is pressed.
In the recovery mode, as far as I remember, the bottom button is used to scroll the cursor down and top button is used to select. Cursor goes back to the top when the end of the list is reached and then comes down in cycle.
Click to expand...
Click to collapse
It goes in test mode not in recovery