Related
well, i tried to install cyanogen mod 7.2 official with no succes
i downloaded the files needed (gapps and cyanogen) put in sd card and i turn off phone then boot up again while pressing home.
i wipe factory reset + user data
then i went in sd card and install both gapps and cyanogen(first) afterwards i reboot the phone. my phone boot normally, it displays samsung and then it displays android and stuck on it..... and when i try to turn the phone off it turn on by itself again . i have to remove battery so that it wont turn on again... help plz need to know what to do ><
i bet u didnt do a " wipe cache partition" try it and report.....and remember that the first boot takes a bit long( the cm7 boot animation goes on and on )
and is your phone gt s5830 or gt s5830i???? bcoz the cm7 rom is ONLY for gts5830
reply fast...
Are you sure you did that with Cwm 5, and not the stock recovery???
If not, install Cwm 5, wipe everything, install Cm 7.2, reboot.
Then reboot again in recovery, and install Gapps.
Done!
Edit: Don not forget to mount system and data before flashing gapps.
Sent from my GT-S5830 using xda premium
when i enter recovery system (home + power)
in yellow appling multi csc E: failed to mount system invalid argument
and each time i wipe cache partition/ data factory reset : rfs format failed on /dev/st113
and /dev/st114
but i tried to install cyanogem 7.2 then reboot and then my phone boot normally but stuck on android
like it shows a black screen and on the center it shows android(in white)....
MadDoxX_imba said:
when i enter recovery system (home + power)
in yellow appling multi csc E: failed to mount system invalid argument
and each time i wipe cache partition/ data factory reset : rfs format failed on /dev/st113
and /dev/st114
but i tried to install cyanogem 7.2 then reboot and then my phone boot normally but stuck on android
like it shows a black screen and on the center it shows android(in white)....
Click to expand...
Click to collapse
PLZ help me ><
MadDoxX_imba said:
PLZ help me ><
Click to expand...
Click to collapse
u still didnt answer this question from earlier guy who ask
Darvadouille said:
Are you sure you did that with Cwm 5, and not the stock recovery???
Click to expand...
Click to collapse
so let me ask again, on what recovery are u on? stock? cwm 4? cwm 5?
an0nym0us_ said:
u still didnt answer this question from earlier guy who ask
so let me ask again, on what recovery are u on? stock? cwm 4? cwm 5?
Click to expand...
Click to collapse
i dont know what that means, i followed a guide i found on the internet.
i didnt had cwm 4 neither stock or whatever.... i had android and the guide told me to download cwm 7.2 + gapps and report with home+power and wipe user partition and wipe factory reset and then install cwm from sd... now my phone just display android on screen each time it boot and stuck on it zZz
anyone can tell me what to do plz? i just want to get my phone working again TT
Yeah right. Nowadays people never stop to amaze me. U want to flash cm yet u didnt even know what recovery u use. Didnt the tutoriual u followed mention anything about cm roms needs cwm recovery?
Now my advice would be flashing stock rom via odin and stay with it before u do any more damage to the poor phone. look in the sticky thread or in the dev subforum howto flash stock rom via odin.
an0nym0us_ said:
Yeah right. Nowadays people never stop to amaze me. U want to flash cm yet u didnt even know what recovery u use. Didnt the tutoriual u followed mention anything about cm roms needs cwm recovery?
Now my advice would be flashing stock rom via odin and stay with it before u do any more damage to the poor phone. look in the sticky thread or in the dev subforum howto flash stock rom via odin.
Click to expand...
Click to collapse
just a last question, is it possible to flash pphone via sd card? cuz i dont have wires to connect my phone to pc ><
Nope, not possible. U need a working pc with windows and a usb cable if u wanna flash stock rom via odin.
ok thx i gonna give it a try as soon i got a usb cable for my phone.
Hi All!
I have an HTC One X+, International. I have decided to try and "play" with it and so I have Unlocked and Rooted and then tried Installing a Custom Rom, based on those instructions:
http://forum.xda-developers.com/showthread.php?t=2213910
Unlock and Root went well, and so installing TWRP (its present).
Then I got here: http://forum.xda-developers.com/showthread.php?t=2067325
After trying to install the ROM (first image then zip - followed the instructions), the device is booting with the CM logo spinning, but then it gives out an "Unfortunately, NFC Service has stopped " error...
Please help!
I tried to go back to the original restore via TWRP - no luck. The HTC screen appears and then stuck in it.
moxah1981 said:
Hi All!
I have an HTC One X+, International. I have decided to try and "play" with it and so I have Unlocked and Rooted and then tried Installing a Custom Rom, based on those instructions:
http://forum.xda-developers.com/showthread.php?t=2213910
Unlock and Root went well, and so installing TWRP (its present).
Then I got here: http://forum.xda-developers.com/showthread.php?t=2067325
After trying to install the ROM (first image then zip - followed the instructions), the device is booting with the CM logo spinning, but then it gives out an "Unfortunately, NFC Service has stopped " error...
Please help!
I tried to go back to the original restore via TWRP - no luck. The HTC screen appears and then stuck in it.
Click to expand...
Click to collapse
Try and flash another ROM & Image. It appears the ROM might not have been downloaded properly.
BTW what happened after it gave the NFC error? Did you complete the rest of the process and simply restarted the device?
flash the CORRECT kernel! read the op!!!!!!! why do you people not read?! seriously!
full wipe the rom before flashing CM on top of whatever you had before!
the rom works correct! the problem is you
Cant flash another rom
Addicted2xda said:
Try and flash another ROM & Image. It appears the ROM might not have been downloaded properly.
BTW what happened after it gave the NFC error? Did you complete the rest of the process and simply restarted the device?
Click to expand...
Click to collapse
I cant get a new rom to the device - the computer stopped recognizing it and I have no idea how to get a file on it (maybe somehow via the terminal/SDK.bat?).
After it gives the NFC error, there is an "OK' button. I hit it a few times and nothing happens. Then the screen goes off and I cant turn it back on, unless I use the power button/volume down...
I did though tried a different image... same result.
moxah1981 said:
I cant get a new rom to the device - the computer stopped recognizing it and I have no idea how to get a file on it (maybe somehow via the terminal/SDK.bat?).
After it gives the NFC error, there is an "OK' button. I hit it a few times and nothing happens. Then the screen goes off and I cant turn it back on, unless I use the power button/volume down...
I did though tried a different image... same result.
Click to expand...
Click to collapse
I am assuming you have latest ADB tools installed in your system.
You can use ADB sideload to copy ROM in the phone
When you are pressing the powerbutton + vol down - I hope you are getting to boot loader?
Lloir said:
flash the CORRECT kernel! read the op!!!!!!! why do you people not read?! seriously!
full wipe the rom before flashing CM on top of whatever you had before!
the rom works correct! the problem is you
Click to expand...
Click to collapse
Hi Lloir!
I much appreciate the personnel response and the time you took to reply to me.
Before I had the original HOX+ rom+sense and I believe I DID a full wipe
I flashed the kernel from your post. I believe that my lack of knowledge lead me to download the wrong one (?) boot-BLADE-42-201305062233
Would you be so kind and please guide me to the correct steps? I have spent several hours allready trying to fix this issue.
Once again, your (and everyone else`s) help is MUCH appreciated!
moxah1981 said:
Hi Lloir!
I much appreciate the personnel response and the time you took to reply to me.
Before I had the original HOX+ rom+sense and I believe I DID a full wipe
I flashed the kernel from your post. I believe that my lack of knowledge lead me to download the wrong one (?) boot-BLADE-42-201305062233
Would you be so kind and please guide me to the correct steps? I have spent several hours allready trying to fix this issue.
Once again, your (and everyone else`s) help is MUCH appreciated!
Click to expand...
Click to collapse
sorry for my ranty response: anyway
the kernel you need is boot-BLADE-CM10.1-whateverdatehere
not the 42 kernels, those are for AOSP\PA\AOKP
soon this won't be an issue
-Lloir
Addicted2xda said:
I am assuming you have latest ADB tools installed in your system.
You can use ADB sideload to copy ROM in the phone
When you are pressing the powerbutton + vol down - I hope you are getting to boot loader?
Click to expand...
Click to collapse
Sorry, I am going to try Lloir`s solution... You guys reply so fast that I dont manage to reply in time to all!
THANK YOU very much!
Lloir said:
sorry for my ranty response: anyway
the kernel you need is boot-BLADE-CM10.1-whateverdatehere
not the 42 kernels, those are for AOSP\PA\AOKP
soon this won't be an issue
-Lloir
Click to expand...
Click to collapse
This was FAST answer!
I see my mistake (reading comprehension) :
CM10 - for 4.1 based roms e.g. CM10 and AOKP 4.1.2
CM10.1 - ONLY for CM10.1
42 - 4.2 based roms e.g. AOKP 4.2.1 and AOSP 4.2.1
I thought that your ROM is based on the 4.2 (?)
Downloading the Kernel now.
By the way, when and how do I add the gapps?
flash kernel
flash rom
after rom flash the gapps
vensterbank said:
flash kernel
flash rom
after rom flash the gapps
Click to expand...
Click to collapse
Thank you. I already flashed kernel and rom. Phone booted up and seem to work. A few issues:
1) I did not put the gapps zip on the phone before the process.
2) Though the phone appears as a drive in Windows, I can not copy any file to it.
3) Camera says NO SD Card and exits....
Thank you for your help!
moxah1981 said:
This was FAST answer!
I see my mistake (reading comprehension) :
CM10 - for 4.1 based roms e.g. CM10 and AOKP 4.1.2
CM10.1 - ONLY for CM10.1
42 - 4.2 based roms e.g. AOKP 4.2.1 and AOSP 4.2.1
I thought that your ROM is based on the 4.2 (?)
Downloading the Kernel now.
By the way, when and how do I add the gapps?
Click to expand...
Click to collapse
Even if you install gapps after one full reboot - it won't be a problem... Actually - it's whenver you feel like
moxah1981 said:
Thank you. I already flashed kernel and rom. Phone booted up and seem to work. A few issues:
1) I did not put the gapps zip on the phone before the process.
2) Though the phone appears as a drive in Windows, I can not copy any file to it.
3) Camera says NO SD Card and exits....
Thank you for your help!
Click to expand...
Click to collapse
Go to the Lloir's thread there is a solution for it - I read. I don't remember it as I am not using AOSP / AOKP / CM ROM at the moment...
Addicted2xda said:
Even if you install gapps after one full reboot - it won't be a problem... Actually - it's whenver you feel like
Click to expand...
Click to collapse
Hi,
See my next post -
1) I cant copy any files to the phone.
2) I dont know HOW to install the gapps
Sorry for being a noob
moxah1981 said:
Hi,
See my next post -
1) I cant copy any files to the phone.
2) I dont know HOW to install the gapps
Sorry for being a noob
Click to expand...
Click to collapse
Use ADB sideload to copy the file...
I believe that will work.
Addicted2xda said:
Use ADB sideload to copy the file...
I believe that will work.
Click to expand...
Click to collapse
Thank you! What do I do AFTER I get the gapps.zip to the phone? what do I do with the TWRP?
Is this what I should do to get the zip to the phone:
Set the device into ADB sideload mode. In TWRP you do this by going to Advanced then ADB Sideload.
From the command line, type adb sideload /path/to/rom.zip
moxah1981 said:
Thank you! What do I do AFTER I get the gapps.zip to the phone? what do I do with the TWRP?
Is this what I should do to get the zip to the phone:
Set the device into ADB sideload mode. In TWRP you do this by going to Advanced then ADB Sideload.
From the command line, type adb sideload /path/to/rom.zip
Click to expand...
Click to collapse
Yup.
Then from TWRP flash the Zip.
Wipe Cache & Davlik...
Reboot...
Addicted2xda said:
Yup.
Then from TWRP flash the Zip.
Wipe Cache & Davlik...
Reboot...
Click to expand...
Click to collapse
ADB termianl says : "error: device not found"
Phone plugged to USB, debug mode etc...
Maybe I should just re-flash EVERYTHING - rom, image?
UPDATE: re-done everything, full wipe. Still camera wont work - "No sd card..." ALSO, still cant move anything to phone... help!
Gmail app?
OK, got the latest gapps. Installed.
Play Store wont open, camera says no sd card and no Gmail app (???)
moxah1981 said:
OK, got the latest gapps. Installed.
Play Store wont open, camera says no sd card and no Gmail app (???)
Click to expand...
Click to collapse
Did you create the '0' folder before flashing the ROM?
If not - would suggest you to load some other ROM...
Also, check the Lloir''s thread...
Hi,
I've been trying to install CM 11 based on Kitkat 4.4.2 on my Xperia P. The following are the details / steps followed:
- The bootloader is unlocked
- The phone is rooted
- CWM 6.0.1.2 is installed ( I think this is the latest available for Xperia P)
1) Downloaded CM11-RC1 from the links in this thread http://forum.xda-developers.com/showthread.php?t=2626639
2) Modified 'updater-script' to get rid of Error 7
3) Extracted 'boot.img' and flashed it using FlashTool in fastboot mode.
After reboot, the phone stops at Sony logo and vibrates once.
4) Pressed the Power button to load CWM Recovery
5) Wiped Data, Cache/Partition, Dalvik Cache
6) Tried to install CM11-RC1 zip file using CWM
Now I get the message "Installation aborted", as soon as the installation begins, without any error code being displayed
I can't seem to get past this step, and don't know where I'm going wrong.
Can anyone please help me out?
Are you sure that your phone is unlocked bootloader ? Did you unlocked yourself ? And you should not change anything in update script because i had flash this rom without problem ...
Sent from my Xperia P using Tapatalk 2
-ss- said:
Are you sure that your phone is unlocked bootloader ? Did you unlocked yourself ? And you should not change anything in update script because i had flash this rom without problem ...
Sent from my Xperia P using Tapatalk 2
Click to expand...
Click to collapse
Yes. The bootloader is unlocked. I did it myself following the instructions on the Sony website.
The installation shows an error 7 if I don't modify the updater script.
Delete sorry
Sent from my Xperia P using Tapatalk
yomayne said:
Yes. The bootloader is unlocked. I did it myself following the instructions on the Sony website.
The installation shows an error 7 if I don't modify the updater script.
Click to expand...
Click to collapse
What i have done with flashing this rom was just followed the OP : format system, format data and format catch then flash ROM and gapps without problem ...
Sent from my Xperia P using Tapatalk 2
-ss- said:
What i have done with flashing this rom was just followed the OP : format system, format data and format catch then flash ROM and gapps without problem ...
Sent from my Xperia P using Tapatalk 2
Click to expand...
Click to collapse
Could it be a version issue? Which one did you flash? I did RC1
Hey I had exactly the same problem. What I did was this:
I used Sony Mobile EMMA to re-install latest stock firmware.
After that I rooted it and Installed CWM 1.0 Nypon, I believe this is CWM somewhere in V6.xxxx (other versions wouldn't work for me..)
I also edited the updater script because it wouldn't pass the assert section, so I deleted this.
After that Recompiled it, (Zip format ofcourse) and copied it to SD card.
Next, I flashed boot.img and rebooted the phone after that. Then access CWM.
Now what I did was userdata/factory reset after that I deleted cache, and last but not least dalvik cache.
After that I flashed the recompiled ROM file and then It passed the status 7 error.
When that was finished I flashed gapps
This was what I did, becuz' I had exactly the same problem. I don't know if this works for you but you might give it a try.
(Sorry for bad Englisch)
(Make sure that your bootloader is unlocked! (To verify, I did try to unlock it again. Then I got a message saying that it was allready unlocked)
ReplayMitta said:
Hey I had exactly the same problem. What I did was this:
I used Sony Mobile EMMA to re-install latest stock firmware.
After that I rooted it and Installed CWM 1.0 Nypon, I believe this is CWM somewhere in V6.xxxx (other versions wouldn't work for me..)
I also edited the updater script because it wouldn't pass the assert section, so I deleted this.
After that Recompiled it, (Zip format ofcourse) and copied it to SD card.
Next, I flashed boot.img and rebooted the phone after that. Then access CWM.
Now what I did was userdata/factory reset after that I deleted cache, and last but not least dalvik cache.
After that I flashed the recompiled ROM file and then It passed the status 7 error.
When that was finished I flashed gapps
This was what I did, becuz' I had exactly the same problem. I don't know if this works for you but you might give it a try.
(Sorry for bad Englisch)
(Make sure that your bootloader is unlocked! (To verify, I did try to unlock it again. Then I got a message saying that it was allready unlocked)
Click to expand...
Click to collapse
Thanks. I'll try doing that. Let's see if it works. Which CM11 build did you flash?
yomayne said:
Thanks. I'll try doing that. Let's see if it works. Which CM11 build did you flash?
Click to expand...
Click to collapse
I flashed RC1 also, I tried almost all nightly's and the RC1 lol but they all wouldn't work before I used this sort of 'method'
Yesterday RC1 workied succesfully for me, today I updated to nightly 25 and everything works fine. Note that once you get passed the installation of RC1, that you can only access the CWM recovery with holding the power button, when your phone vibrates when you see the sony logo.. The CW11 comes with CMW touchable. Goodluck
And did it work?
I've solved my status 7 problem with this video ;
http://www.youtube.com/watch?v=QW1znjDLe-k
gilgin said:
I've solved my status 7 problem with this video ;
http://www.youtube.com/watch?v=QW1znjDLe-k
Click to expand...
Click to collapse
Auful way way to "fix" things.
You can "fix" galaxy ROM to be installed on your phone and brick it permanently, it's already been done.
If you have flashed galaxy kernel you probably won't be able to boot but still able to recover.
Tha asserts are there for a reason.
ChikeD said:
Auful way way to "fix" things.
You can "fix" galaxy ROM to be installed on your phone and brick it permanently, it's already been done.
If you have flashed galaxy kernel you probably won't be able to boot but still able to recover.
Tha asserts are there for a reason.
Click to expand...
Click to collapse
I didn't flash a wrong kernel or rom. İf friend is sure of the right pack to flash, than he can use this method.
I wanted to flash cm nightly 25 (percy's rom) to my xperia p, and the cwm gave status 7 error. Then i have searched a solution for my problem, and i found this video and did what he shows in the video, and i have a cm11 flashed xperia p now. And i also flashed over cm11-weekly.
(sorry if i have a bad english)
gilgin said:
I didn't flash a wrong kernel or rom. İf friend is sure of the right pack to flash, than he can use this method.
I wanted to flash cm nightly 25 (percy's rom) to my xperia p, and the cwm gave status 7 error. Then i have searched a solution for my problem, and i found this video and did what he shows in the video, and i have a cm11 flashed xperia p now. And i also flashed over cm11-weekly.
(sorry if i have a bad english)
Click to expand...
Click to collapse
Sp they released a ROM that cannot be flushed, is that what you say? And no one else reporting it?
Somehow I find it difficult to believe.
If you have followed the instructions I'm sure there would be no problem, or the instructions are incomplete, or there is some issue, either way it's up to the developer to fix it.
Avoid "fixing" errors in this manner or one day you may regret it dearly.
ChikeD said:
Sp they released a ROM that cannot be flushed, is that what you say? And no one else reporting it?
Somehow I find it difficult to believe.
If you have followed the instructions I'm sure there would be no problem, or the instructions are incomplete, or there is some issue, either way it's up to the developer to fix it.
Avoid "fixing" errors in this manner or one day you may regret it dearly.
Click to expand...
Click to collapse
I have followed the instructions in a good way and this was the problem i have lived. Some of my friends lived this problem in a Turkish Forum and i recommended this way, they did it and flash the rom. I will give the link here; http://forum.donanimhaber.com/m_58138440/mpage_242/f_//tm.htm#87204228
My nick is ENG_civ on that forum. Everything is right about the rom but something goes in a wrong way, so this way makes the compiler not asking "is this right rom?", that's all. İn my opinion, if you are sure of the rom, there is no risk.
And i am new in this forum, and i couldn't write at development part, and this is the first time i am writing to a foreign language forum. So i couldn't reported them, and these rom's are not the final, so there could be faults on them i think.
gilgin said:
I've solved my status 7 problem with this video ;
(video)
Click to expand...
Click to collapse
I solved the problem with the CM11 this way too. But when I tried to install gapps after install cm11 appear the "status 7". What can I do?
Edit: I can flash the normal cm11 (without edit the .txt) but the problem with the gapps continues. I turned on my phone and then the cyanogenmod logo start running and don't leave this screen. Anyone can help me?
Error:
set_metadata_recursive: some changes failed
E:Error in /storage/sdcard0/gapps-kk-20140105.signed.zip (status 7)
Installation aborted.
nortonz said:
I solved the problem with the CM11 this way too. But when I tried to install gapps after install cm11 appear the "status 7". What can I do?
Edit: I can flash the normal cm11 (without edit the .txt) but the problem with the gapps continues. I turned on my phone and then the cyanogenmod logo start running and don't leave this screen. Anyone can help me?
Error:
set_metadata_recursive: some changes failed
E:Error in /storage/sdcard0/gapps-kk-20140105.signed.zip (status 7)
Installation aborted.
Click to expand...
Click to collapse
For gapps its normal. Its actually flashed
Sent from my Xperia P using Tapatalk
AndroidNoob69 said:
For gapps its normal. Its actually flashed
Sent from my Xperia P using Tapatalk
Click to expand...
Click to collapse
How "normal" ?
PS: now my celphone has cyanogenmod 11 ! I'm so glad and grateful for this post!
nortonz said:
How "normal" ?
Click to expand...
Click to collapse
'normal' as in everyone has it. The zip is actually flashed.
Sent from my Xperia P using Tapatalk
It worked!
Thanks so much ! I'm finally running 4.4.2
Hello guys, im lg g2 mini (d618) owner. Yesterday i get root for last update of my device. After dat i decided to flash cwm, but i missclicked and not noticed that i chose Kernel flash. Now my phone boots to logo and screen is purple, after purple screen loads cwm. Idk what to do. Guys help pls and sry for such bad eng :c
upd
Is it possible to flash original boot.img?
ww_w.youtube.com/watch?v=rV4gr8qhhzM&feature=youtu.be
Suicadere said:
Hello guys, im lg g2 mini (d618) owner. Yesterday i get root for last update of my device. After dat i decided to flash cwm, but i missclicked and not noticed that i chose Kernel flash. Now my phone boots to logo and screen is purple, after purple screen loads cwm. Idk what to do. Guys help pls and sry for such bad eng :c
upd
Is it possible to flash original boot.img?
ww_w.youtube.com/watch?v=rV4gr8qhhzM&feature=youtu.be
Click to expand...
Click to collapse
try to flash - wipe data etc and install an original rom or a custom rom .. you ****ed the system..
Abarai91 said:
try to flash - wipe data etc and install an original rom or a custom rom .. you ****ed the system..
Click to expand...
Click to collapse
i'll try. Nope.
Is any other issues of theese?
Man put the new rom with gaps on SD and install
Inviato dal mio LG-D620 utilizzando Tapatalk
Abarai91 said:
Man put the new rom with gaps on SD and install
Inviato dal mio LG-D620 utilizzando Tapatalk
Click to expand...
Click to collapse
I tryed. But its dont works
But it doesn't seem the phone is dead it give u the options to install and do what u want from recovery
Send with - LG g2 mini - d620
Abarai91 said:
But it doesn't seem the phone is dead it give u the options to install and do what u want from recovery
Send with - LG g2 mini - d620
Click to expand...
Click to collapse
i flashed cwm instead of original boot.img coz im dumb
so i have 2 recovery now, cwm and stock
U can have 2 solution
1)put rom on SD card then wipe data. After it will ask u to install from SD card and do the procedure...
2)do an hard reset. Search on xda how to do it...
Send with - LG g2 mini - d620
18911
Abarai91 said:
U can have 2 solution
1)put rom on SD card then wipe data. After it will ask u to install from SD card and do the procedure...
2)do an hard reset. Search on xda how to do it...
Send with - LG g2 mini - d620
Click to expand...
Click to collapse
1) dont't works
2)can't hard reset. After boot i see logo aaand after screen becomes purple so i cant enter hard reset mode (fast press vol up and power) or Download mode
But you did a "wipe date" ? Try to another partition and if it work deleted the new recovery with triangle away
Send with - LG g2 mini - d620
Abarai91 said:
But you did a "wipe date" ? Try to another partition and if it work deleted the new recovery with triangle away
Send with - LG g2 mini - d620
Click to expand...
Click to collapse
same
Abarai91 said:
But you did a "wipe date" ? Try to another partition and if it work deleted the new recovery with triangle away
Send with - LG g2 mini - d620
Click to expand...
Click to collapse
somehow i have entered Factory Reset menu aaaand i press yes. but same
Flash KDZ
sebatox said:
Flash KDZ
Click to expand...
Click to collapse
I can't enter download mode and pc can't see device
Suicadere said:
I can't enter download mode and pc can't see device
Click to expand...
Click to collapse
then bring the phone to assistence... but i think it's something wrong with you lol becouse you can access recovery and you should do what u want
Abarai91 said:
then bring the phone to assistence... but i think it's something wrong with you lol becouse you can access recovery and you should do what u want
Click to expand...
Click to collapse
the only thing dat i've done installed twrp. now i have 2 custom recovery modes. I try to boot rom, but it not boots after install.
recovery just reboots due install. I think i need working backup, coz i can boot my broken. Can u zip sys and boot backup for me? Please?
I.have italy version d620r. Now i m busy e when i go home i lo do it
Send with - LG g2 mini - d620
Suicadere said:
the only thing dat i've done installed twrp. now i have 2 custom recovery modes. I try to boot rom, but it not boots after install.
recovery just reboots due install. I think i need working backup, coz i can boot my broken. Can u zip sys and boot backup for me? Please?
Click to expand...
Click to collapse
ok tell me what i have to do to help you
Maybe you should try with Lg mobile support tool app in the pc conect the cell to pc first , if you are lucky enough it will recognize the cell and download the drivers , and then you can go to recovery from update error option
veritovdr said:
Maybe you should try with Lg mobile support tool app in the pc conect the cell to pc first , if you are lucky enough it will recognize the cell and download the drivers , and then you can go to recovery from update error option
Click to expand...
Click to collapse
i'm not so lucky. Tryed it several times. No result.
EVERYTHING THAT HAPPENED
I was running on AICP, then i noticed that Stock rom for marshmallow was out. So i tried installing it with twrp it gave me some errors and then installed the stock recovery and then installed the Stock rom, it all went well. After installation everything was working and i wanted to root then get the TWRP back, then i rooted my device using kingroot and installed TWRP using TWRP manager the app showed that it's a success and the i booted into recovery but then nor was i able to access the recovery neither able to install the stock recovery . Then I tried to unlock the bootloader and install recovery using adb. I followed the oneplus fourm thread(cannot post outside links as I'm a new member) to do everything and then after the command " fastboot oem unlock" my phone did try to reboot but i got stuck on the bootlogo and i cannot access the recovery as well.
ONLY fastboot mode seems to be working.
:crying:
can anyone tell me how should i go about this?
EDIT: My device was fixed. I followed the Unbricking thread by Naman Bhalla and yea it worked.
Link- http://forum.xda-developers.com/oneplus-x/general/guide-mega-unbrick-guide-hard-bricked-t3272108
i m facing the same problem.
please anybody help.
did your issue got solved bro?
You installed stock recovery, right ? then boot into it, wipe everything and flash Stock OOS 2.2.2.
If still doesn't work, the install official TWRP, do a full wipe, and install any Custom ROM, see if that resolves your issue.
All links can be found on the Index Thread.
Not really
Joshwin Aranha said:
You installed stock recovery, right ? then boot into it, wipe everything and flash Stock OOS 2.2.2.
If still doesn't work, the install official TWRP, do a full wipe, and install any Custom ROM, see if that resolves your issue.
All links can be found on the Index Thread.
Click to expand...
Click to collapse
I wasn't able to access my recovery then also but I fixed my device yesterday , my device was hard bricked XD
well i followed this http://forum.xda-developers.com/oneplus-x/general/guide-mega-unbrick-guide-hard-bricked-t3272108 thread by Naman Bhalla and it worked like a charm. IF anyone is still facing the issue follow this thread.
Hello.
anshu4590 said:
i m facing the same problem.
please anybody help.
Click to expand...
Click to collapse
Bro, Folllow this http://forum.xda-developers.com/oneplus-x/general/guide-mega-unbrick-guide-hard-bricked-t3272108 thread step by step and it will be resolved .
Akash52k said:
Bro, Folllow this http://forum.xda-developers.com/oneplus-x/general/guide-mega-unbrick-guide-hard-bricked-t3272108 thread step by step and it will be resolved .
Click to expand...
Click to collapse
Thnks bro
anshu4590 said:
Thnks bro
Click to expand...
Click to collapse
No problem man :laugh: